Browse
Records Added in April 2023
Records added in April 2023
Change month: January | February | March | April | May | June | July | August | September | October | November | December
8593. LAPSE:2023.26896
Comparative Analysis of Effectiveness of Resistance and Induction Turnout Heating
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: Energy Efficiency, induction heating, railway, resistance heating, safety of rail traffic, stock-rail, switch-rail, turnouts
Turnouts are key parts of rail roads and are exposed to adverse weather conditions such as snowfall, snow drifts, low temperatures, or sleet. Effective protection assures good turnout function and contributes to rail traffic efficiency and safety. Presently, resistance heating (RH) is the most common system of turnout heating in Europe. In this study, we attempted to implement energy-saving induction heating (IH) in order to cut costs of operation and electricity. A turnout heating test stand, including a stock-rail and a switch-rail, was executed in a climatic chamber. Air temperature was constant at the time of heating. Active power received by both the systems was identical for any measurement (450 W). Test results enabled an assessment of switch-rail position and variations of climatic chamber air temperature on growth of turnout temperatures. Effects of heating type on correct lubrication of the slide plate surface were compared. Dynamics of heating variations and their impact on... [more]
8594. LAPSE:2023.26895
Variable Pitch Propeller for UAV-Experimental Tests
April 3, 2023 (v1)
Subject: Optimization
Keywords: drone, drone rotor, energy optimization, experimental aerodynamics, UAV, variable pitch propeller
Growth in application fields of unmanned aerial vehicles (UAVs) and an increase in their total number are followed by higher and higher expectations imposed on improvements in UAV propulsion and energy management systems. Most commercial vertical takeoff and landing (VTOL) UAVs employ a constant pitch propeller that forces a mission execution tradeoff in the majority of cases. An alternative solution, presented here, consists of the use of a variable pitch propeller. The paper summarizes experimental measurements of the propulsion system equipped with an innovative variable pitch rotor. The investigations incorporated characteristics of the rotor for no wind conditions and a new approach to optimize pitch settings in hover flight as a function of UAV weight and energy consumption. As UAV battery capacity is always limited, efficient energy management is the only way to increase UAV mission performance. The study shows that use of a variable pitch propeller can increase the maximal take... [more]
8595. LAPSE:2023.26894
Effect of Insulation on the Energy Demand of a Standardized Container Facility at Airports in Spain under Different Weather Conditions
April 3, 2023 (v1)
Subject: Materials
Keywords: airports, HVAC, insulation, PCM, standard shipping container
Airports, broadly spread world-wide, present continuously increasing energy demands for heating and cooling purposes. Relocatable facilities within them could be built on recycling shipping containers provided with the right insulation layer, to reduce the outstanding consumption of the heating, ventilation and air conditioning systems (HVAC). This research focuses on studying the effect of added insulation on the thermal performance of a construction in the scope of an airport facility, based on a recycled shipping container. Passive heating and cooling insulation strategies have shown good results in terms of energy savings. A series of simulations were performed along six different Spanish airports locations, selected to represent several climate conditions. Temperature evolution inside the container, and energy demands of the HVAC system were obtained to show that the insulation provided by phase change materials (PCM) is performing better than traditional insulation, or a raw cont... [more]
8596. LAPSE:2023.26893
Duckweed from a Biorefinery System: Nutrient Recovery Efficiency and Forage Value
April 3, 2023 (v1)
Subject: Biosystems
Keywords: biogas plant, duckweed, farm biorefinery, nutritional value, P and N recovery
This paper presents the results of an interdisciplinary study aimed at assessing the possibility of using duckweed to purify and recover nutrients from the effluent remaining after struvite precipitation and ammonia stripping from a liquid fraction of anaerobic digestate in a biorefinery located at a Dutch dairy cattle production farm. The nutritional value of duckweed obtained in a biorefinery was assessed as well. Duckweed (Lemna minuta) was cultured on a growth medium with various concentrations of effluent from a biorefinery (EFL) and digested slurry (DS) not subjected to the nutrient recovery process. The study’s results showed that duckweed culture on the media with high contents of DS or EFL was impossible because they both inhibited its growth. After 15 days of culture, the highest duckweed yield was obtained from the ponds with DS or EFL contents in the medium reaching 0.39% (37.8 g fresh matter (FM) and 16.8 g FM per 8500 mL of the growth medium, respectively). The recovery o... [more]
8597. LAPSE:2023.26892
Numerical Study of CO2 Geological Storage in Saline Aquifers without the Risk of Leakage
April 3, 2023 (v1)
Subject: Numerical Methods and Statistics
Keywords: dissolved CO2 injection, mineralization mechanisms, storage safety
The purpose of this study is to reduce the risk of leakage of CO2 geological storage by injecting the dissolved CO2 solution instead of the supercritical CO2 injection. The reservoir simulation method is used in this study to evaluate the contributions of the different trapping mechanisms, and the safety index method is used to evaluate the risk of CO2 leakage. The function of the dissolved CO2 solution injection is performed by a case study of a deep saline aquifer. Two scenarios are designed in this study: the traditional supercritical CO2 injection and the dissolved CO2 solution injection. The contributions of different trapping mechanisms, plume migrations, and the risk of leakage are evaluated and compared. The simulation results show that the risk of leakage via a natural pathway can be decreased by the approach of injecting dissolved CO2 solution instead of supercritical CO2. The amount of the CO2 retained by the safe trapping mechanisms in the dissolved CO2 solution injection s... [more]
8598. LAPSE:2023.26891
A Probabilistic Modeling Based on Monte Carlo Simulation of Wind Powered EV Charging Stations for Steady-States Security Analysis
April 3, 2023 (v1)
Subject: Modelling and Simulations
Keywords: electric vehicles charging demands, Gaussian mixture distribution, Monte-Carlo simulation, steady-states security analysis, Weibull distribution, wind power output
As renewable energy resources such as wind and solar power are developing and the penetration of electric vehicles (EVs) is increasingly integrated into existing systems, uncertainty and variability in power systems have become important issues. The charging demands for EVs and wind power output are recognized as highly variable generation resources (VGRs) with uncertainty, which can cause unexpected disturbances such as short circuits. This can deteriorate the reliability of existing power systems. In response, research is required to identify the uncertainties presented by VGRs and is required to examine the ability of power system models to reflect those uncertainties. The deterministic method, which is the most basic method that is currently in use, does not reflect the uncertainty of system components. Therefore, this paper proposes a probabilistic method to assess the steady-state security of power systems, reflecting the uncertainty of VGRs using Monte Carlo simulation (MCS). In... [more]
8599. LAPSE:2023.26890
Modeling of the Thermal Efficiency of a Whole Cement Clinker Calcination System and Its Application on a 5000 MT/D Production Line
April 3, 2023 (v1)
Subject: Modelling and Simulations
Keywords: decomposition rate, effective heat, thermal efficiency, whole system
This paper proposes that the scope of research should be extended to the whole clinker calcination system from its single device or specific process (i.e., its functional subunits) as conventionally conducted. Mass/heat flow and effective heat were first analyzed to obtain the thermal efficiencies of its subunits (φi); a thermal efficiency model of the whole system φQY was thus established by correlating the relationship between φi and φQY. The thermal efficiency model of the whole system showed that φi had a positive linear correlation with φQY; it was found that the thermal efficiency of the decomposition and clinker calcination unit (φDC) had the greatest weight on φQY, where a 1% increase in φDC led to a 1.73% increase in φQY—improving φDC was shown to be the most effective way to improve φQY. In this paper, the developed thermal efficiency model was applied to one 5000 MT/D production line. It was found that its φQY was only 61.70%—about 2.35% lower than a representative line; suc... [more]
8600. LAPSE:2023.26889
Next-Day Prediction of Hourly Solar Irradiance Using Local Weather Forecasts and LSTM Trained with Non-Local Data
April 3, 2023 (v1)
Subject: Process Control
Keywords: long short-term memory, solar irradiance, weather prediction
Solar irradiance prediction is significant for maximizing energy-saving effects in the predictive control of buildings. Several models for solar irradiance prediction have been developed; however, they require the collection of weather data over a long period in the predicted target region or evaluation of various weather data in real time. In this study, a long short-term memory algorithm−based model is proposed using limited input data and data from other regions. The proposed model can predict solar irradiance using next-day weather forecasts by the Korea Meteorological Administration and daily solar irradiance, and it is possible to build a model with one-time learning using national and international data. The model developed in this study showed excellent predictive performance with a coefficient of variation of the root mean square error of 12% per year even if the learning and forecast regions were different, assuming that the weather forecast was correct.
8601. LAPSE:2023.26888
Experimental Study on the Inhibition Effects of Nitrogen and Carbon Dioxide on Coal Spontaneous Combustion
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: Carbon Dioxide, coal spontaneous combustion, inhibition effect, nitrogen
Inert gases can effectively inhibit coal spontaneous combustion. In this paper, the inhibition effect of inert gases (N2 and CO2) on coal spontaneous combustion was studied. In the low-temperature oxidation stage, the constant-temperature heat release and apparent activation energy of coal sample were measured and calculated by the C80 micro-calorimeter. In the high-temperature combustion stage, the critical temperature, maximum peak temperature, ignition temperature, and burn-out temperature of coal samples were analyzed by the synchronous thermal analyzer. The results demonstrate that with the decrease of O2 concentration, the oxidation heat release of coal samples drops gradually while the apparent activation energy increases gradually. In the N2 and CO2 atmospheres, as the O2 concentration is reduced to 1.5% and 3%, respectively, the value of apparent activation energy changes from negative to positive, and the spontaneous reaction transits to a nonspontaneous reaction. The TG-DTG... [more]
8602. LAPSE:2023.26887
Dutch Hybrid Neighbourhoods of 1860−1910 in Heat Transition: The Case Study of Zeeheldenkwartier in The Hague
April 3, 2023 (v1)
Subject: Energy Policy
Keywords: energy transition, heritage, hybrid neighbourhood
This paper explores the typo-morphologic characteristics of late 19th century hybrid neighbourhoods in urban regions of The Netherlands and possibilities of a feasible climate neutral energy system in the future. The Zeeheldenkwartier neighbourhood in The Hague is used as a case study. Sustainable Development Goals (SDG) are involved to ensure access to affordable and clean energy (SDG 7) and make cities inclusive, safe, resilient and sustainable (SDG 11). With the 2019 Dutch-Climate-Agreement The Netherlands decided on a neighbourhood approach to the transition from natural gas to a climate neutral energy supply in buildings. Implicit homogeneity in most buildings of neighbourhoods is presupposed, in contrast to older neighbourhoods that were laid out before World War I. These are nowadays heterogenic, attractive, mixed and often protected neighbourhoods because of the quality of the architecture. Establishing a generic energy plan here is a challenge. The foremost important conclusio... [more]
8603. LAPSE:2023.26886
Potential and Impacts of Cogeneration in Tropical Climate Countries: Ecuador as a Case Study
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: Biomass, cogeneration, industrial energy efficiency, Sustainability, trigeneration, tropical climate country
High dependency on fossil fuels, low energy efficiency, poor diversification of energy sources, and a low rate of access to electricity are challenges that need to be solved in many developing countries to make their energy systems more sustainable. Cogeneration has been identified as a key strategy for increasing energy generation capacity, reducing greenhouse gas (GHG) emissions, and improving energy efficiency in industry, one of the most energy-demanding sectors worldwide. However, more studies are necessary to define approaches for implementing cogeneration, particularly in countries with tropical climates (such as Ecuador). In Ecuador, the National Plan of Energy Efficiency includes cogeneration as one of the four routes for making energy use more sustainable in the industrial sector. The objective of this paper is two-fold: (1) to identify the potential of cogeneration in the Ecuadorian industry, and (2) to show the positive impacts of cogeneration on power generation capacity,... [more]
8604. LAPSE:2023.26885
Stability Analysis and Optimal Design for Virtual Impedance of 48 V Server Power System for Data Center Applications
April 3, 2023 (v1)
Subject: Process Design
Keywords: output impedance, stability analysis, virtual impedance
In the past literature on virtual impedance to series systems, most of the discussion focused on stability without in-depth research on the system design of the series converter and the overall output impedance. Accordingly, this study takes an open-loop resonant LLC converter series-connected closed-loop Buck converter as an example. First, the conditions required for the direct connection of the small-signal model in the series, the effect of feedback compensation on the input impedance of the load stage, the operating frequency, and passive components of the two-stage converter are discussed in detail―the relationship between the matching and the output impedance. Afterwards, a mathematical model is used to discuss the effect of adding parallel virtual impedance on the output impedance of the overall series converter and then derive an optimized virtual impedance design. Finally, an experimental platform of 48 V to 12 V and maximum wattage of 96 W are implemented. The output impedan... [more]
8605. LAPSE:2023.26884
Role of TiO2 Phase Composition Tuned by LiOH on The Electrochemical Performance of Dual-Phase Li4Ti5O12-TiO2 Microrod as an Anode for Lithium-Ion Battery
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: hydrothermal, Li4Ti5O12-TiO2, lithium-ion battery, microrod, TiO2 rutile
In this study, a dual-phase Li4Ti5O12-TiO2 microrod was successfully prepared using a modified hydrothermal method and calcination process. The stoichiometry of LiOH as precursor was varied at mol ratio of 0.9, 1.1, and 1.3, to obtain the appropriate phase composition between TiO2 and Li4Ti5O12. Results show that TiO2 content has an important role in increasing the specific capacity of electrodes. The refinement of X-ray diffraction patterns by Rietveld analysis confirm that increasing the LiOH stoichiometry suppresses the TiO2 phase. In the scanning electron microscopy images, the microrod morphology was formed after calcination with diameter sizes ranging from 142.34 to 260.62 nm and microrod lengths ranging from 5.03−7.37 μm. The 0.9 LiOH sample shows a prominent electrochemical performance with the largest specific capacity of 162.72 mAh/g and 98.75% retention capacity achieved at a rate capability test of 1 C. This finding can be attributed to the appropriate amount of TiO2 that i... [more]
8606. LAPSE:2023.26883
Integration of a Heuristic Multi-Agent Protection System into a Distribution Network Interconnected with Distributed Energy Resources
April 3, 2023 (v1)
Subject: Energy Management
Keywords: distributed energy resources (DER), heuristic decision making, interconnected distribution network, multi-agent system, power system protection
In conventional method protection schemes are devised for certain operation conditions with fixed settings throughout their operation life, however, protection systems in interconnected distribution networks rely on a detailed analysis of fault current contribution and variation in operation conditions under real-world scenarios. In fact, the concept of Adaptive Protection System (APS) and possibility of the adjustment for protection settings within modern Intelligent Electronic Devices (IEDs) have introduced desired functionalities for protection systems to cope with complex operation scenarios envisioned within future power system networks. In this paper, a novel protection system based on Multi-Agent System (MAS) and heuristic decision-making is proposed to update protection settings of the protection IEDs with respect to prevailing operation conditions in an interconnected distribution network. The adopted methodology is reliant on real-time simulation of a distribution network int... [more]
8607. LAPSE:2023.26882
Screening Life Cycle Assessment of Tall Oil-Based Polyols Suitable for Rigid Polyurethane Foams
April 3, 2023 (v1)
Subject: Environment
Keywords: environment assessment, life cycle assessment, polyols, polyurethane, tall oil
A screening Life Cycle Assessment (LCA) of tall oil-based bio-polyols suitable for rigid polyurethane (PU) foams has been carried out. The goal was to identify the hot-spots and data gaps. The system under investigation is three different tall oil fatty acids (TOFA)-based bio-polyol synthesis with a cradle-to-gate approach, from the production of raw materials to the synthesis of TOFA based bio-polyols at a pilot-scale reactor. The synthesis steps that give the most significant environmental footprint hot-spots were identified. The results showed the bio-based feedstock was the main environmental hot-spot in the bio-polyol production process. Future research directions have been highlighted.
8608. LAPSE:2023.26881
AATTENUATION—The Atmospheric Attenuation Model for CSP Tower Plants: A Look-Up Table for Operational Implementation
April 3, 2023 (v1)
Subject: Process Operations
Keywords: atmospheric extinction, attenuation loss, central receiver, CSP, solar energy, solar resource assessment, solar tower plant, transmittance model
Attenuation of solar radiation between the receiver and the heliostat field in concentrated solar power (CSP) tower plants can reduce the overall system performance significantly. The attenuation varies strongly with time and the average attenuation at different sites might also vary strongly from each other. If no site specific attenuation data is available, the optimal plant design cannot be determined and rough estimations of the attenuation effect are required leading to high uncertainties of yield analysis calculations. The attenuation is caused mainly by water vapor content and aerosol particles in the lower atmospheric layer above ground. Although several on-site measurement systems have been developed during recent years, attenuation data sets are usually not available to be included during the plant project development. An Atmospheric Attenuation (AATTENUATION) model to derive the atmospheric transmittance between a heliostat and receiver on the basis of common direct normal i... [more]
8609. LAPSE:2023.26880
Thermocatalytic Pyrolysis of Exhausted Arthrospira platensis Biomass after Protein or Lipid Recovery
April 3, 2023 (v1)
Subject: Biosystems
Keywords: Biofuels, FTIR, GC–MS, microalgae, silica–alumina, zeolite
Microalgae and cyanobacteria are unicellular microorganism that contain high-added-value compounds. To make their extraction economically feasible, the biorefinery concept is the only solution. In this study, the residues resulting from lipid or protein extraction from Arthrospira platensis biomass were valorized by catalytic pyrolysis using ZSM5 zeolite or amorphous silica−alumina as catalyst. The reaction was performed in a quartz reactor, and the catalysts were placed in a fixed bed, to force the reaction gases to pass through it. The reaction products were analyzed by FTIR and GC−MS analyses. The reaction gases and liquids obtained from the extraction residues had higher hydrocarbon contents compared with the untreated biomass. Moreover, the pyrolysis of biomass after protein extraction led to fractions with lower nitrogenated component contents, while that after lipid extraction to fractions with lower oxygenated component contents. This study showed that the pyrolysis process cou... [more]
8610. LAPSE:2023.26879
Operation Analysis of a SAG Mill under Different Conditions Based on DEM and Breakage Energy Method
April 3, 2023 (v1)
Subject: Process Operations
Keywords: DEM, fill level, mill power, mill speed, SAG mill, steel ball ratio
As one of the machines widely used in mining, a semi-autogenous grinding (SAG) mill can significantly improve the roughing efficiency of rock. But the SAG mill still faces the obstacles of significant energy consumption and empirical operation parameters. In order to obtain the optimal operation parameters of a SAG mill, in this paper, the discrete element method (DEM) is used to simulate the breakage process of the particles by controlling three parameters, i.e., the mill speed ratio, the mill fill level ratio, and the steel ball ratio. This method simulates the particles size, mill power, and qualified particles quality of crushed particle, which reveal the grinding strength and energy consumption of the SAG mill. In this paper, the grinding changes of a SAG mill under different parameter conditions are explored. Firstly, an experiment on the influence of a single parameter change on the mill’s operation is set up, and then the influence of three parameter changes on the mill’s opera... [more]
8611. LAPSE:2023.26878
Identification of the Determinants of the Effectiveness of On-Road Chicanes in Transition Zones to Villages Subject to a 70 km/h Speed Limit
April 3, 2023 (v1)
Subject: System Identification
Keywords: chicane, solar cells, speed reduction, speed restriction, traffic calming, transition zone
In recent decades traffic calming, especially in villages situated on through roads, has become an urgent issue. Various schemes are applied in the transition zones to reduce the inbound traffic speeds and thus improve the traffic safety. The studies conducted in several countries point to different determinants of the speed reduction obtained in this way. This article deals with the schemes including a central island horizontally deflecting one lane, located in transition zones to villages with 70 km/h speed restriction on two-lane roads (6 m carriageway width). In order to identify the speed reduction determinants, the speeds before and after chicanes were measured and the effect of the three criteria was investigated, characterising: the traffic management scheme, road design parameters, landscape elements present in the surroundings of the transition zone and visibility conditions. Based on the confirmation of logical tautology of many pre-selected factors, one aggregate parameter... [more]
8612. LAPSE:2023.26877
Feedback Linearization Based Robust Control for Linear Permanent Magnet Synchronous Motors
April 3, 2023 (v1)
Subject: Other
Keywords: feedback linearization, linear permanent magnet synchronous motor, robust control
In this study, we designed a feedback linearization control strategy for linear permanent magnet synchronous motors (LPMSMs) as well as a robust control mechanism. First, the highly nonlinear system was transformed into an exact linear system by the feedback linearization technique. Then, we designed a robust controller to mitigate the impact of system parameter disturbances on system performance. This novel robust feedback controller can be applied to electromagnetic force, speed and position control loops in linear motors, correct the errors created by uncertainty factors in the entire system in real time, and set the system’s settling time based on the application environment of the plant. Finally, we performed simulations and experiments using a PC-based motor control system, which demonstrated that the proposed robust feedback controller can achieve good performance in the controlled system with robust anti-disturbance control.
8613. LAPSE:2023.26876
Numerical and Physical Simulation of Heat Transfer Enhancement Using Oval Dimple Vortex Generators—Review and Recommendations
April 3, 2023 (v1)
Subject: Modelling and Simulations
Keywords: efficiency, experiment, heat transfer enhancement, hydraulic resistance, numerical simulation, oval dimples, vortex generators
Vortex generation and flow disruption in heat exchanger passages by means of surface modification is a widely used passive heat transfer augmentation technique. The present paper contains the results of numerical and experimental studies of the hydraulic resistance and heat transfer in the rectangle duct with oval-trench- and oval-arc-shaped dimples applied to the heat transfer surface. For the turbulent flow in the duct (Pr = 0.71, Red = 3200−9 × 104—for heat transfer determination and Red = 500−104—for the friction factor measurements), rational geometrical parameters of the oval-trench dimple were determined: relative elongation of dimple l/b = 5.57−6.78 and relative depth l/b = 5.57−6.78, while the value of the attack angle to the mean flow was fixed φ = (45−60)°. The comparison of the experimental and numerical modeling for the flow in the narrow duct over the surface with a single- and multi-row dimple arrangement has revealed a good agreement. It was found that the average heat... [more]
8614. LAPSE:2023.26875
Thermal Calculation and Experimental Investigation of Electric Heating and Solid Thermal Storage System
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: experimental investigation, fluid-solid coupling, heat transfer characteristics, solid sensible heat storage, thermal calculation
Electric heating and solid thermal storage systems (EHSTSSs) are widely used in clean district heating and to flexibly adjust combined heat and power (CHP) units. They represent an effective way to utilize renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of an EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed. The calculation flow and calculation method for key parameters of the heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by the FLUENT 15 software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the E... [more]
8615. LAPSE:2023.26874
Look Ahead Based Control Strategy for Hydro-Static Drive Wind Turbine Using Dynamic Programming
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: dynamic program, hydro-static turbine, non-linear optimization, wind energy
This research paper presents a look-ahead optimal control strategy for a Hydro-static Drive Wind Turbine when look ahead wind speed information is available. The proposed predictive controller is a direct numerical optimizer based on the well established principles of Hamilton-Jacobi-Bellman (Dynamic Programming). Hydro-static transmission based, non-linear model of wind turbine is used in this optimization work. The optimal behavior of the turbine used the non-linearity of aerodynamic maps and hydro-static drive train by a convex combination of state space controller with measurable generator speed and hydraulic motor displacement as scheduling parameters. A comparative analysis between a optimal controller based on Maximum Power Point Tracking (MPPT) algorithm as published in literature and the proposed look ahead based predictive controller is presented. The simulation results show that proposed look ahead strategy offered optimal operation of the wind turbine by closely tracking th... [more]
8616. LAPSE:2023.26873
Feasible Reserve in Day-Ahead Unit Commitment Using Scenario-Based Optimization
April 3, 2023 (v1)
Subject: Planning & Scheduling
Keywords: metaheuristic optimization, Particle Swarm Optimization, reserve schedule, robust optimization, unit commitment
This paper investigates the feasible reserve of diesel generators in day-ahead unit commitment (DAUC) in order to handle the uncertainties of renewable energy sources. Unlike other studies that deal with the ramping of generators, this paper extends the ramp rate consideration further, using dynamic limits for the scheduling of available reserves (feasible reserve) to deal with hidden infeasible reserve issues found in the literature. The unit commitment (UC) problem is solved as a two-stage day-ahead robust scenario-based unit commitment using a metaheuristic new variant of particle swarm optimization (PSO) called partitioned step PSO (PSPSO) that can deal with the dynamic system. The PSPSO was pre-optimized and was able to find the solution for the base-case UC problem in a short time. The evaluation of the optimized UC schedules for different degrees of reserve consideration was analyzed. The results reveal that there is a significant advantage in using the feasible reserve formulat... [more]
8617. LAPSE:2023.26872
Enhanced CH4-CO2 Hydrate Swapping in the Presence of Low Dosage Methanol
April 3, 2023 (v1)
Subject: Food & Agricultural Processes
Keywords: anti-agglomeration, CH4-CO2 hydrate swapping, Methanol, surface active compound
CO2-rich gas injection into natural gas hydrate reservoirs is proposed as a carbon-neutral, novel technique to store CO2 while simultaneously producing CH4 gas from methane hydrate deposits without disturbing geological settings. This method is limited by the mass transport barrier created by hydrate film formation at the liquid−gas interface. The very low gas diffusivity through hydrate film formed at this interface causes low CO2 availability at the gas−hydrate interface, thus lowering the recovery and replacement efficiency during CH4-CO2 exchange. In a first-of-its-kind study, we have demonstrate the successful application of low dosage methanol to enhance gas storage and recovery and compare it with water and other surface-active kinetic promoters including SDS and L-methionine. Our study shows 40−80% CH4 recovery, 83−93% CO2 storage and 3−10% CH4-CO2 replacement efficiency in the presence of 5 wt% methanol, and further improvement in the swapping process due to a change in temper... [more]
[0.07 s]

