Browse
Records Added in April 2023
Records added in April 2023
Change month: January | February | March | April | May | June | July | August | September | October | November | December
8618. LAPSE:2023.26871
Experimental Investigation of Critical Heat Flux on Different Surfaces at Low Pressure and Low Flow
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: annulus, critical heat flux, flow boiling, Inconel 625, low pressure, two phase flow
Steady state flow boiling experiments were carried out on several heated tubes with outer diameter 9.14 mm at outlet pressures 120, 200 and 300 kPa, inlet temperatures 64, 78 and 91 °C and approximately 400, 500, 600 and 800 kg/(m2·s) mass flux entering the vertically aligned test annulus until critical heat flux (CHF) was reached. The tubes were made of Inconel 625 with a length of 400 mm. The Inconel tubes were tested in three different modifications as smooth, abraded with 150 grit sandpaper and bead blasted. Multiple experiments were repeated on the same specimen to investigate the effect of surface characteristic changes (i.e., wettability, roughness and oxide layer morphology) on the occurrence of CHF. Despite the changes in initial wettability, the CHF dependency was not clearly observed, however, the changes in roughness led to an increase in CHF. The total number of 115 experimental runs were collected and the results were also compared with other literature experimental data.
8619. LAPSE:2023.26870
A Novel Approach to the Analysis of Thermal Response Test (TRT) with Interrupted Power Input
April 3, 2023 (v1)
Subject: Other
Keywords: borehole thermal parameters, interrupted power input, measuring outputs, thermal response test (TRT)
The quality of measuring datasets of the thermal response test (TRT) significantly influences the interpretation of borehole thermal parameters (BTP). A thermal response test with an unstable power input may induce an unacceptable error in the estimation of the borehole thermal parameters. This paper proposes a novel approach to treat the dataset with interrupted power input. In this approach, the test records were segmented into several subsections with a constant time interval of 100 min, 60 min, and 30 min, separately. The quality of each data section was assessed and analyzed. Then, two algorithms, including the continuous algorithm and semi-superposition algorithm, were developed. The results estimated by the linear source model (LSM) were compared with one Thermal response test datasets with a stable power input at the same testing site. It shows that the effects of power interruption during the test can be effectively mitigated by deploying both the continuous and semi-superposi... [more]
8620. LAPSE:2023.26869
Seismic Reflection Coefficient Inversion Using Basis Pursuit Denoising in the Joint Time-Frequency Domain
April 3, 2023 (v1)
Subject: Numerical Methods and Statistics
Keywords: basis pursuit denoising, dominant frequency band, joint time-frequency inversion, reflection coefficient, sparse constraint
Seismic reflection coefficient inversion in the joint time-frequency domain is a method for inverting reflection coefficients using time domain and frequency domain information simultaneously. It can effectively improve the time-frequency resolution of seismic data. However, existing research lacks an analysis of the factors that affect the resolution of inversion results. In this paper, we analyze the influence of parameters, such as the length of the time window, the size of the sliding step, the dominant frequency band, and the regularization factor of the objective function on inversion results. The SPGL1 algorithm for basis pursuit denoising was used to solve our proposed objective function. The applied geological model and experimental field results show that our method can obtain a high-resolution seismic reflection coefficient section, thus providing a potential avenue for high-resolution seismic data processing and seismic inversion, especially for thin reservoir inversion and... [more]
8621. LAPSE:2023.26868
Fast Pyrolysis of Lignin Pretreated with Magnesium Formate and Magnesium Hydroxide
April 3, 2023 (v1)
Subject: Materials
Keywords: lignin, magnesium salts, pyrolysis
Kraft lignin (Indulin AT) pretreated with magnesium formate and magnesium hydroxide was fast-pyrolyzed in a continuously fed, bench-scale system. To avoid fouling issues typically associated with lignin pyrolysis, a simple laboratory test was used to determine suitable ranges of magnesium hydroxide and formic acid to lignin for feeding without plugging problems. Various feedstock formulations of lignin pretreated with magnesium hydroxide and formic acid were pyrolyzed. For comparison, calcium formate pretreated lignin was also tested. The organic oil yield ranged from 9% to 17% wt % on a lignin basis. Carbon yields in the oil ranged from 10% to 18% wt % on a lignin basis. Magnesium formate pretreatment increased oil yield and carbon yield in the oil up to 35% relative to the higher 1:1 g magnesium hydroxide/g lignin pretreatment. However, a lower magnesium hydroxide pretreatment (0.5:1 g magnesium hydroxide/g lignin) resulted in oil yields and carbon yields in the oils similar to the m... [more]
8622. LAPSE:2023.26867
Dynamic Stall Model for Tower Shadow Effects on Downwind Turbines and Its Scale Effects
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: blade element and momentum method, downwind rotor, tower shadow
A dynamic stall model for tower shadow effects is developed for downwind turbines. Although Munduate’s model shows good agreement with a 1.0 m wind tunnel test model, two problems exist: (1) it does not express load increase before the entrance of the tower wake, and (2) it uses the empirical tower wake model to determine the wind speed profile behind the tower. The present research solves these problems by combining Moriarty’s tower wake model and the entrance condition of the tower wake. Moriarty’s model does not require any empirical parameter other than tower drag coefficient and it expresses positive wind speed around the tower also. Positive wind speed change is also allowed as the tower wake entrance condition in addition to the negative change observed in the previous model. It demonstrates better agreement with a wind tunnel test and contributes to the accuracy of the fatigue load, as it expresses a slight increase in load around the entrance of the tower wake. Furthermore, th... [more]
8623. LAPSE:2023.26866
Tax Reform for the Energy Transition in Korea’s Power Generation Sector
April 3, 2023 (v1)
Subject: Energy Policy
Keywords: economic dispatch model, energy transition, merit order, Pigouvian tax
The tax structure capable of achieving an energy transition in the power sector was analyzed by applying the Pigouvian tax on generation fuels. Under the 2018 Tax Act Amendment, the tax rate criteria for the excise tax on power generation fuels changed from the calorific value to environmental externalities of the fuel. However, to reverse the merit order of bituminous coal generation with liquefied natural gas (LNG) generation, reflecting only some external costs of the environment as a tax is not enough. In this paper, we established four tax reform scenarios for bituminous coal and LNG considering environmental externalities, and we analyzed the reversal of dispatch priority using the electricity system unit commitment and M-Core economic dispatch model. According to the analysis results, the share of bituminous coal generation will be reduced to 10−20% depending on the scenario, reflecting the relative tax rate equalizing the fuel costs of bituminous coal and LNG power. To achieve... [more]
8624. LAPSE:2023.26865
Low-Carbon R&D Can Boost EU Growth and Competitiveness
April 3, 2023 (v1)
Subject: Energy Policy
Keywords: D, endogenous technology progress, GEM-E3-FIT, innovation-induced growth, low-carbon R&
Research and Innovation (R&I) are a key part of the EU strategy towards stronger growth and the creation of more and better jobs while respecting social and climate objectives. In the last decades, improvements in costs and performance of low-carbon technologies triggered by R&I expenditures and learning-by-doing effects have increased their competitiveness compared to fossil fuel options. So, in the context of ambitious climate policies as described in the EU Green Deal, increased R&I expenditures can increase productivity and boost EU economic growth and competitiveness, especially in countries with large innovation and low-carbon manufacturing base. The analysis captures the different nature of public and private R&I, with the latter having more positive economic implications and higher efficiency as it is closer to industrial activities. Public R&D commonly focuses on immature highly uncertain technologies, which are also needed to achieve the climate neutrality target of the EU. T... [more]
8625. LAPSE:2023.26864
Non-Strategic Capacity Withholding from Distributed Energy Storage within Microgrids Providing Energy and Reserve Services
April 3, 2023 (v1)
Subject: Energy Management
Keywords: ancillary services, battery energy storage systems, capacity degradation, capacity withholding, microgrids, power system economics, power system reliability
Microgrids have the potential to provide security and flexibility to power systems through the integration of a wide range of resources, including distributed energy storage, usually in the form of batteries. An aggregation of microgrids can enable the participation of these resources in the main system’s energy and ancillary services market. The traditional minimum-cost operation, however, can undermine microgrid’s ability to hold reserve capacity for operation in islanded mode and can rapidly degrade distributed batteries. This paper studies the impacts of various operational strategies from distributed energy storage plants on their revenues and on market prices, considering an array of microgrids that act in a synchronized fashion. The operational model minimizes the entire electric power system cost, considering transmission-connected and distributed energy resources, and capturing capacity degradation of batteries as part of the cost function. Additionally, microgrid-based, distr... [more]
8626. LAPSE:2023.26863
Lifting Off Spatial Degeneracy of Functions, Where Does It Lead Us for Photovoltaic Device Systems?
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: concentrator solar cell, discrete translational symmetry, high efficiency, redirection waveguide, two-dimensional photoreceptor-conversion (2DPRC) scheme
The defact standard of a solar cell is that electric power generation is made at the same place as photoharvesting is performed, i.e., the function of photoharvesting/photoreception is spatially degenerated with that of electric power generation (photo-electroconversion). Here, in this review paper, we investigate how liberated we are when the degeneracy is lifted off. A conventional concentrator system is, in a sense, a system in which the primary photoharvesting place is decoupled from the photo-conversion part, but is too bulky because the two parts are connected three-dimensionally by photons. We propose a two-dimensional photoreceptor-conversion (2DPRC) scheme in which the photoreception part is spatially decoupled from, but is two-dimensionally connected to the photo-conversion part by a redirection waveguide (RWG). The whole system is in an edge-illumination/photoinjection configuration and concentrator system is quite naturally built, and the edge-injection lift off the trade-o... [more]
8627. LAPSE:2023.26862
A Linear Relaxation-Based Heuristic for Iron Ore Stockyard Energy Planning
April 3, 2023 (v1)
Subject: Planning & Scheduling
Keywords: heuristic methods, iron ore stockyard energy planning, linear relaxation-based heuristic, mixed integer linear programming
Planning the use of electrical energy in a bulk stockyard is a strategic issue due to its impact on efficiency and responsiveness of these systems. Empirical planning becomes more complex when the energy cost changes over time. The mathematical models currently studied in the literature consider many actors involved, such as equipment, sources, blends, and flows. Each paper presents different combinations of actors, creating their own transportation flows, thus increasing the complexity of this problem. In this work, we propose a new mixed integer linear programming (MILP) model for stockyard planning solved by a linear relaxation-based heuristic (LRBH) to minimize the plan’s energy cost. The proposed algorithm will allow the planner to find a solution that saves energy costs with an efficient process. The numerical results show a comparison between the exact and heuristic solutions for some different instances sizes. The linear relaxation approach can provide feasible solutions with a... [more]
8628. LAPSE:2023.26861
Clarke Transformation Solution of Asymmetrical Transients in Three-Phase Circuits
April 3, 2023 (v1)
Subject: Numerical Methods and Statistics
Keywords: analytical methods, asymmetrical three-phase transients, Clarke transformation, space vector representation, time-domain analysis
This work deals with the use of the Clarke transformation for the theoretical derivation of circuit models for the analysis of asymmetrical transients in three-phase circuits. Asymmetrical transients occur when only one or two phases of a three-phase power system are involved in a switch operation. Such a condition is critical from a theoretical viewpoint since the Clarke transformation is based on the assumption of circuit symmetry between the three phases. If the symmetry assumption is not met, the equivalent circuits in the transformed variables α, β, and 0 are not uncoupled. The literature concerning numerical approaches for asymmetrical transient analysis is very rich, but a comprehensive and rigorous analytical investigation of circuit models within the framework of the Clarke transformation is still lacking. Contrary to numerical approaches, analytical solutions provide deeper insight into the phenomenon and allow for theoretical interpretation and better understanding of the tr... [more]
8629. LAPSE:2023.26860
Variable Geometry in Miniature Gas Turbine for Improved Performance and Reduced Environmental Impact
April 3, 2023 (v1)
Subject: Environment
Keywords: combustion chamber variable geometry, gas turbine efficiency, hot section variable geometry, miniature gas turbine, variable area turbine nozzle
A miniature gas turbine (MGT) is proposed as a promising future energy source. Increasingly stringent requirements related to harmful combustible gas emissions and a trend towards improved energy generation efficiency drive the quest for new MGT technologies. Variable geometry systems are promising due to enhanced heat management and flow control. Variable combustor cooling and dilution holes together with the variable area nozzle (VAN) system allow for the improvement of gas turbine performance and reduction in pollutant emissions. The proposed systems are based on hot-section geometry changes, in which the size of the combustion chamber holes and turbine nozzle angle can be adjusted. Component and module experimental research were performed at the Warsaw University of Technology, on an MGT test stand. A significant decrease in fuel consumption (up to 47% reduction) and harmful nitrogen oxide emission reduction (NO−by 78% and NO2−by 82%) were achieved. These results are related to com... [more]
8630. LAPSE:2023.26859
Recent Advances in Technology, Strategy and Application of Sustainable Energy Systems
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: Biomass, building energy conservation, electric system, emission reduction, fuel conversion efficiency, Renewable and Sustainable Energy
The global COVID-19 pandemic has had strong impacts on national and international freight, construction and tourism industry, supply chains, and has resulted in a rapid decline in the demand for traditional energy sources. In fact, research has outlined that urban areas depend on global supply chains for their day-to-day basic functions, including energy supplies, food and safe access to potable water. The disruption of global supply chains can leave many urban areas in a very vulnerable position, in which their citizens may struggle to obtain their basic supplies, as the COVID-19 crisis has recently shown. Therefore, solutions aiming to enhance local food, water and energy production systems, even in urban environments, have to be pursued. The COVID-19 crisis has also highlighted in the scientific community the problem of people’s exposure to outdoor and indoor pollution, confirmed as a key element for the increase both in the transmission and severity of the contagion, on top of invo... [more]
8631. LAPSE:2023.26858
Improvement of the Pseudocapacitive Performance of Cobalt Oxide-Based Electrodes for Electrochemical Capacitors
April 3, 2023 (v1)
Subject: Materials
Keywords: cobalt oxide nanoparticles, core-shell nanoparticles, electrode material, reduced cobalt oxide, supercapacitor
Cobalt oxide nanopowders are synthesized by the pyrolysis of aerosol particles of water solution of cobalt acetate. Cobalt nanopowder is obtained by subsequent reduction of obtained cobalt oxide by annealing under a hydrogen atmosphere. The average crystallite size of the synthesized porous particles ranged from 7 to 30 nm, depending on the synthesis temperature. The electrochemical characteristics of electrodes based on synthesized cobalt oxide and reduced cobalt oxide are investigated in an electrochemical cell using a 3.5 M KOH solution as the electrolyte. The results of electrochemical measurements show that the electrode based on reduced cobalt oxide (Re-Co3O4) exhibits significantly higher capacity, and lower Faradaic charge−transfer and ion diffusion resistances when compared to the electrodes based on the initial cobalt oxide Co3O4. This observed effect is mainly due to a wide range of reversible redox transitions such as Co(II) ↔ Co(III) and Co(III) ↔ Co(IV) associated with di... [more]
8632. LAPSE:2023.26857
A Study on the Application Possibility of the Vehicle Air Conditioning System Using Vortex Tube
April 3, 2023 (v1)
Subject: Environment
Keywords: temperature separation, the low-temperature air flow ratio (yc), inlet pressure (Pi), vortex generator, vortex tube
Since refrigerants applied to vehicle air conditioning systems exacerbate global warming, many studies have been conducted to supplement them. However, most studies have attempted to maximize the efficiency and minimize the environmental impact of the refrigerant, and thus, an air conditioning system without refrigerant is required. The vortex tube is a temperature separation system capable of separating air at low and high temperatures using compressed air. When applied to an air conditioning system, it is possible to construct an eco-friendly system that does not use a refrigerant. In this paper, various temperature changes and characteristics of a vortex tube were identified and applied to an air conditioning system simulation device. Additionally, an air conditioning system simulation device using indirect heat exchange and direct heat exchange methods was constructed to test the low-temperature air flow rate (yc), according to the temperature and pressure. As a result of the exper... [more]
8633. LAPSE:2023.26856
Optimized Single-Axis Schedule Solar Tracker in Different Weather Conditions
April 3, 2023 (v1)
Subject: Planning & Scheduling
Keywords: efficiency of solar panels, electronic control unit, encoder, exact orientation to the Sun, schedule- and LDR-based solar trackers, single-axis solar tracker
Improving the efficiency of solar panels is the main task of solar energy generation. One of the methods is a solar tracking system. One of the most important parameters of tracking systems is a precise orientation to the Sun. In this paper, the performance of single-axis solar trackers based on schedule and light dependent resistor (LDR) photosensors, as well as a stationary photovoltaic installation in various weather conditions, were compared. A comparative analysis of the operation of a manufactured schedule solar tracker and an LDR solar tracker in different weather conditions was performed; in addition, a simple method for determining the rotation angle of a solar tracker based on the encoder was proposed. Finally, the performance of the manufactured solar trackers was calculated, taking into account various weather conditions for one year. The proposed single-axis solar tracker based on schedule showed better results in cloudy and rainy weather conditions. The obtained results c... [more]
8634. LAPSE:2023.26855
Influence of Active Power Output and Control Parameters of Full-Converter Wind Farms on Sub-Synchronous Oscillation Characteristics in Weak Grids
April 3, 2023 (v1)
Subject: Process Control
Keywords: active power output, control parameters, eigenvalue analysis, full-converter wind, subsynchronous oscillation, weak grids
Active power outputs of a wind farm connected to a weak power grid greatly affect the stability of grid-connected voltage source converter (VSC) systems. This paper studies the impact of active power outputs and control parameters on the subsynchronous oscillation characteristics of full-converter wind farms connected weak power grids. Eigenvalue and participation factor analysis was performed to identify the dominant oscillation modes of the system under consideration. The impact of active power output and control parameters on the damping characteristics of subsynchronous oscillation is analysed with the eigenvalue method. The analysis shows that when the phase-locked loop (PLL) proportional gain is high, the subsynchronous oscillation damping characteristics are worsened as the active power output increases. On the contrary, when the PLL proportional gain is small, the subsynchronous oscillation damping characteristics are improved as the active power output increases. By adjusting... [more]
8635. LAPSE:2023.26854
Similitude Analysis of Experiment and Modelling of Immiscible Displacement Effects with Scaling and Dimensional Approach
April 3, 2023 (v1)
Subject: Numerical Methods and Statistics
Keywords: dimensional analysis, dimensionless products, immiscible displacement, mathematical modelling, regression analysis, scaling, similitude
This paper presents the use of scaling and dimensional analysis to assess the viability of conventional modelling of immiscible displacement occurring when water is injected into the oil-saturated, porous rock—a conventional secondary oil-recovery method. A brief description of the laboratory tests of oil displacement with water performed on long core sets taken from wells operating on a Polish oil reservoir was presented. A dimensionless product generator based on dimensional analysis and Buckingham Π theorem was used to generate all possible combinatorial sets of dimensionless products for physical variables describing the phenomenon. The mathematical model of the phenomenon was transformed to its dimensionless form, using a selected set of the products. The results of the laboratory tests were analyzed as functions of the products. Statistically verified quantities describing both dependent and independent experiment variables were subject to a regression analysis to study dependenc... [more]
8636. LAPSE:2023.26853
Study on the Effect of Second Injection Timing on the Engine Performances of a Gasoline/Hydrogen SI Engine with Split Hydrogen Direct Injecting
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: combustion, emission, hydrogen direct injection, hydrogen mixture distribution, second injection timing, split injection
Split hydrogen direct injection (SHDI) has been proved capable of better efficiency and fewer emissions. Therefore, to investigate SHDI deeply, a numerical study on the effect of second injection timing was presented at a gasoline/hydrogen spark ignition (SI) engine with SHDI. With an excess air ratio of 1.5, five different second injection timings achieved five kinds of hydrogen mixture distribution (HMD), which was the main factor affecting the engine performances. With SHDI, since the HMD is manageable, the engine can achieve better efficiency and fewer emissions. When the second injection timing was 105° crank angle (CA) before top dead center (BTDC), the Pmax was the highest and the position of the Pmax was the earliest. Compared with the single hydrogen direct injection (HDI), the NOX, CO and HC emissions with SHDI were reduced by 20%, 40% and 72% respectively.
8637. LAPSE:2023.26852
A Temperature-Risk and Energy-Saving Evaluation Model for Supporting Energy-Saving Measures for Data Center Server Rooms
April 3, 2023 (v1)
Subject: Environment
Keywords: baseline, continuous and reliable operation, data center, energy saving, energy simulation, Machine Learning, server room, temperature environment, temperature prediction
As data centers have become increasingly important in recent years their operational management must attain higher efficiency and reliability. Moreover, the power consumption of a data center is extremely large, and it is anticipated that it will continue to increase, so energy saving has become an urgent issue concerning data centers. In the meantime, the environment of the server rooms in data centers has become complicated owing to the introduction of virtualization technology, the installation of high-heat density information and communication technology (ICT) equipment and racks, and the diversification of cooling methods. It is very difficult to manage a server room in the case of such a complicated environment. When energy-saving measures are implemented in a server room with such a complicated environment, it is important to evaluate “temperature risks” in advance and calculate the energy-saving effect after the measures are taken. Under those circumstances, in this study, two... [more]
8638. LAPSE:2023.26851
Intelligent Recognition of Insulator Contamination Grade Based on the Deep Learning of Ultraviolet Discharge Image Information
April 3, 2023 (v1)
Subject: Modelling and Simulations
Keywords: contamination grade, deep belief network (DBN), noncontact detection, sparse autoencoder (SAE), ultraviolet image
In order to achieve the noncontact detection of the contamination grade of insulators and to provide guidance for preventing the contamination flashover of insulators based on the pollution state, we propose a contamination grade recognition method based on the deep learning of ultraviolet discharge images using a sparse autoencoder (SAE) and a deep belief network (DBN). Under different humidity conditions, we filmed and preprocessed the ultraviolet discharge images of insulators at different contamination grades and we obtained the ultraviolet spot area sequence as original data for contamination grade recognition. A double-layer sparse autoencoder was used to extract sparse features that could characterize different contamination grades from the ultraviolet spot area sequence. Using the extracted features, a DBN composed of three layers of restricted Boltzmann machine was trained to provide contamination grade recognition. To verify the effectiveness of the method proposed in this pa... [more]
8639. LAPSE:2023.26850
Resonance Stability Analysis of Large-Scale Wind Power Bases with Type-IV Wind Generators
April 3, 2023 (v1)
Subject: Modelling and Simulations
Keywords: negative-resistance effect, resonance stability, s-domain nodal admittance matrix method, Type-IV wind generator (WG)
To guarantee the reliable and efficient development of wind power generation, oscillation problems in large-scale wind power bases with Type-IV generators are investigated from the view of resonance stability in this paper. Firstly, the transfer characteristics of disturbances in Type-IV wind generators are analyzed to establish their impedance model, based on the balance principle of frequency components. Subsequently, considering the dynamic characteristics of the transmission network and the interaction among several wind farms, the resonance structure of a practical wind power base is analyzed based on the s-domain nodal admittance matrix method. Furthermore, the unstable mechanism of the resonance mode is further illustrated by the negative-resistance effect theory. Finally, the established impedance model of the Type-IV wind generator and the resonance structure analysis results of the wind power bases are verified through the time-domain electro-magnetic transient simulation in... [more]
8640. LAPSE:2023.26849
Heat Transfer Enhancement of Plate-Fin Heat Sinks with Different Types of Winglet Vortex Generators
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: friction factor, Nusselt number, plate-fin, thermal enhancement factor, winglet
Because the delta winglet in common-flow-down configuration has been recognized as an excellent type of vortex generators (VGs), this study aims to experimentally and numerically investigate the thermo-hydraulic performance of four different forms of winglet VGs featuring sweptback delta winglets in the channel flow in the range 200 < Re < 1000. Both Nusselt number and friction factor of plate-fin heat sinks having different forms of winglets, including delta winglet pair (DWP), rectangular winglet pair (RWP), swept delta winglet pair (SDWP), and swept trapezoid winglet pair (STWP), were measured in a standard wind tunnel without bypass in this study. Four rows of winglets with in-line arrangement were punched on each 10-mm-long, 0.2-mm-thick copper plate, and a total of 16 pieces of copper plates with spacing of 2 mm were fastened together to achieve the heat sink. The projected area, longitudinal and winglet tip spacing, height and angle of attack of those winglets were fixed.... [more]
8641. LAPSE:2023.26848
Cooperative Control for Multi-Module Charging Systems of Ultracapacitors
April 3, 2023 (v1)
Subject: Process Control
Keywords: cascade control, charging, cooperative control, cyber-physical system, ultracapacitor
Ultracapacitors have recently received great attention for energy storage due to their small pollution, high power density, and long lifetime. In many applications, ultracapacitors need to be charged with a high current, where a multi-module charging system is typically adopted. Although the classical decentralized control method can control the charging process of ultracapacitors, there exists a problem that the charging current may be imbalanced among charging modules. In this paper, a cooperative cascade charging method is proposed for the multi-module charging system to reduce the current imbalance among charging modules. First, the state-space averaging method and graph theory are used to model the multiple-module charging system. Second, an effective cooperative cascade control is proposed, where the outer voltage loop stabilizes the output voltage to the desired voltage and the inner current loop guarantees the current of each charger to follow the target current. The block diag... [more]
8642. LAPSE:2023.26847
Solar-hybrid Thermochemical Gasification of Wood Particles and Solid Recovered Fuel in a Continuously-Fed Prototype Reactor
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: beechwood, Biomass, hybridization, solar gasification, solid recovered fuels, Syngas, waste conversion
Solar thermochemical gasification is a promising solution for the clean production of low-emission synthetic fuels. It offers the possibility to upgrade various biomasses and waste feedstocks and further provides an efficient way to sustainably store solar energy into high-value and energy-intensive chemical fuels. In this work, a novel continuously-fed solar steam gasifier was studied using beechwood and solid recovered fuels (SRF) particles. Solar-only and hybrid solar/autothermal gasification experiments were performed at high temperatures to assess the performance of the reactor and its flexibility in converting various types of feedstocks. The hybrid operation was considered to increase the solar reactor temperature when the solar power input is not sufficient thanks to partial feedstock oxy-combustion. The hybrid solar process is thus a sustainable alternative option outperforming the conventional gasification processes for syngas production. Wood and waste particles solar conver... [more]
[0.07 s]

