Browse
Records Added in April 2023
Records added in April 2023
Change month: January | February | March | April | May | June | July | August | September | October | November | December
8568. LAPSE:2023.26921
A Study for the Optimal Exploitation of Solar, Wind and Hydro Resources and Electrical Storage Systems in the Bormida Valley in the North of Italy
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: hydro, loads, Optimization, Renewable and Sustainable Energy, solar, storage batteries, Wind
The exploitation of distributed renewable energy sources leads to a low-carbon energy transition, mainly based on the optimal integration of hydro, PV and wind power plants with the remaining high-performance fossil-fuel power stations. In the last twenty years, European Union (EU) countries have shown a significant increase of the power installed in new PV and wind power plants, together with the refurbishment of small and medium size hydro stations. In particular, in Italy, PV and wind energy production has strongly increased and nowadays there are regions characterized by a very green energy mix. In this new scenario, energy storage becomes a viable solution to mitigate the variability of renewable energy sources thus optimizing the network operation. The present paper is focused on the Liguria region, in the North of Italy and in particular on the Bormida Valley where nowadays more than the half of the annual electricity consumption is covered by the renewable energy local producti... [more]
8569. LAPSE:2023.26920
Methods to Optimize Carbon Footprint of Buildings in Regenerative Architectural Design with the Use of Machine Learning, Convolutional Neural Network, and Parametric Design
April 3, 2023 (v1)
Subject: Environment
Keywords: AI, Algorithms, Artificial Intelligence, Big Data, circular economy, computer vision, GHG emissions, life cycle assessment, Machine Learning, neural networks, Optimization, parametric, sustainable architecture
The analyzed research issue provides a model for Carbon Footprint estimation at an early design stage. In the context of climate neutrality, it is important to introduce regenerative design practices in the architect’s design process, especially in early design phases when the possibility of modifying the design is usually high. The research method was based on separate consecutive research works−partial tasks: Developing regenerative design guidelines for simulation purposes and for parametric modeling; generating a training set and a testing set of building designs with calculated total Carbon Footprint; using the pre-generated set to train a Machine Learning Model; applying the Machine Learning Model to predict optimal building features; prototyping an application for a quick estimation of the Total Carbon Footprint in the case of other projects in early design phases; updating the prototyped application with additional features; urban layout analysis; preparing a new approach based... [more]
8570. LAPSE:2023.26919
Experimental Investigation of the Effects of Water and Polymer Flooding on Geometric and Multifractal Characteristics of Pore Structures
April 3, 2023 (v1)
Subject: Materials
Keywords: displacement experiment, fractal dimension, multifractal analysis, polymer flooding, pore structure, water flooding
During water and polymer flooding for enhanced oil recovery, pore structures may vary because of the fluid−rock interactions, which can lead to variations in petrophysical properties and affect oil field production. To investigate the effects of fluid flooding on pore structures, six samples were subjected to brine water, dual-system, and alkaline−surfactant−polymer (ASP) polymer displacement experiments. Before and after experiments, samples were scanned by X-ray CT. Thin sections, X-ray diffraction, and high pressure mercury injection tests were also carried out to characterize mineralogy and fractal dimension of pore systems before experiments. Experiment results show that water flooding with low injection pore volume ratio (IPVR) can improve reservoir quality since total porosity and connected porosity of samples rise after the flooding and the proportion of large pores also increases and heterogeneity of pore structure decreases. However, water flooding with high IPVR has reverse... [more]
8571. LAPSE:2023.26918
Regional Disparities and Transformation of Energy Consumption in China Based on a Hybrid Input-Output Analysis
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: energy structure decomposition, Hybrid Input-Output Analysis, RAS method, regional energy consumption
Different regions in China have different energy consumption characteristics and changing trends. This paper focuses on analyzing trends in energy consumption changes along the timeline for 30 regions in China. Using the Hybrid Input-Output Model, this paper decomposes energy consumption in 30 regions in 2007, 2012 and 2016 into energy embedded of final consumption expenditure, gross capital formation, inflow and outflow. We use these four dimensions as coordinates to draw a regional radar map. According to the changing characteristics of the radar map, 30 regions are divided into three groups. By analyzing the reasons for the changes in three regions, we draw the following conclusions. For regions where energy consumption is mainly inflow, the economically developed regions have to form a low energy consumption environment while achieving economic growth. The economically underdeveloped regions need to carry out energy conservation and emission reduction as well as ensuring the level... [more]
8572. LAPSE:2023.26917
Logical-Information Model of Energy-Saving Production of Organic Sulfur Compounds from Low-Molecular Sulfur Waste Fuel Oil
April 3, 2023 (v1)
Subject: Modelling and Simulations
Keywords: energy-saving technology, fuel oil, logical information modeling, sulfur waste, synthesis, wave effects
A logical-informational model of energy resource-efficient chemical technology for the utilization of hydrogen sulfide and low molecular alkanethiols, which are toxic and difficult to remove sulfur components of residual fuel (fuel oil), is proposed. Based on the IDEF1 methodology and existing knowledge about the technological processes of the demercaptanization of various hydrocarbon raw materials (oils, gas condensates), a scheme for the production of organic sulfur compounds from sulfur waste extracted from fuel oil has been modeled. For a sufficiently complete removal of hydrogen sulfide and low molecular weight alkanethiols, energy- and resource-saving stages of the technological process have been developed, which are implemented by ultrasonic and/or magnetic treatment of fuel oil. It is proposed to use the combined action of two alternative methods of processing fuel oil to increase the efficiency of cleaning fuel oil from sulfur components. For the first time, an approach has be... [more]
8573. LAPSE:2023.26916
Experimental Investigation of the Effect of a Recuperative Heat Exchanger and Throttles Opening on a CO2/Isobutane Autocascade Refrigeration System
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: autocascade, Carbon Dioxide, isobutane, natural refrigerants, R744
An experimental evaluation of an autocascade refrigeration (ACR) system was carried out. A zeotropic mixture of isobutane and CO2 was employed as a working fluid in an autocascade refrigeration (ACR) system. An experimental system was designed and built to study the influence of the recuperative heat exchanger (RHX) and openings of the throttle valves on the system performance. The use of RHX facilitated the condensation process and improved the cycle characteristics. The working mass concentration of CO2 was higher, as it was closer to the nominal concentration and the discharge pressure was lower by 19% to even 39% when the RHX was employed in the system. An increase of up to 20% in the coefficient of performance (COP) was observed. Furthermore, the effects of the openings of the throttle valves on the system characteristics were studied. The change in the openings of the expansion valves affected the mass flows and the working mixture composition. The working CO2 mass fraction incre... [more]
8574. LAPSE:2023.26915
Influence of Thermoelastic Phenomena on the Energy Conservation in Non-Contacting Face Seals
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: heat transfer, mechanical seal, non-contacting face seal, thermal analysis
The purpose of this study was to develop a mathematical model for non-contacting face seals to analyze how their performance is affected by thermoelastic phenomena. The model was used to solve thermal conductivity and thermoelasticity problems. The primary goal was to calculate the values of thermal deformations of the sealing rings in a non-contacting face seal with a flexibly mounted rotor (FMR) for a turbomachine. The model assumes the conversion of mechanical energy into heat in the fluid film. The heat flux generated in the fluid film is transferred first to the sealing rings and then to the fluid surrounding them. Asymmetric distribution of temperature within the sealing rings leads to the occurrence of thermal stresses and, consequently, a change in the geometry of the rings. The model is solved analytically. The distributions of temperature fields for the sealing rings in the cross-sections are calculated using the Fourier-Bessel series as a superficial function of two variable... [more]
8575. LAPSE:2023.26914
Diagnoses for Potential Enaction of Water−Energy Nexus in Green Building Rating Systems: Case Study of the Pearl Rating System of United Arab Emirates
April 3, 2023 (v1)
Subject: Environment
Keywords: built environment, Estidama, green buildings rating systems, Pearl Rating System, Sustainability, United Arab Emirates, water–energy nexus
The green building rating system within the sustainability framework of the United Arab Emirates (UAE), the Pearl Rating System (PRS), similar to most international rating systems such as LEED, considers several strategies, regulations, and policies to improve the energy and water performance in buildings. However, the applicability of considering water as part of energy or the fact that the utilization of energy mandates the usage of water seems unexplored and is not yet included in any of the existing building rating systems. A unified approach of water and energy resources is thus vital for future considerations in energy policy, planning, and the inclusion of the same in the sustainability rating systems. This paper investigated, as a case study, the prospects of water−energy nexus in the prevailing UAE green building rating system—PRS—to uncover whether any water conservation strategy has an adverse effect on energy and vice versa. The review revealed that the major shortcomings o... [more]
8576. LAPSE:2023.26913
Thermal and Flow Characteristics in a Concentric Annular Heat Pipe Heat Sink
April 3, 2023 (v1)
Subject: Process Design
Keywords: annular heat pipe, cooling, electronics, heat sink
A concentric annular heat pipe heat sink (AHPHS) was proposed and fabricated to investigate its thermal behavior. The present AHPHS consists of two concentric pipes of different diameters, which create vacuumed annular vapor space. The main advantage of the AHPHS as a heat sink is that it can largely increase the heat transfer area for cooling compared to conventional heat pipes. In the current AHPHS, condensation takes place along the whole annular space from the certain heating area as the evaporator section. Therefore, the whole inner space of the AHPHS except the heating area can be considered the condenser. In the present study, AHPHSs of different diameters were fabricated and studied experimentally. Basic studies were carried out with a 50 mm-long stainless steel AHPHS with diameter ratios of 1.1 and 1.3 and the same inner tube diameter of 76 mm. Several experimental parameters such as volume fractions of 10−70%, different air flow velocity, flow configurations, and 10−50 W heat... [more]
8577. LAPSE:2023.26912
Development of Decision-Making Tool and Pareto Set Analysis for Bi-Objective Optimization of an ORC Power Plant
April 3, 2023 (v1)
Subject: Optimization
Keywords: decision-making, geothermal, multi-objective, Optimization, ORC
Power plants based on organic Rankine cycle (ORC) are known for their capacity in converting low and medium-temperature energy sources to electricity. To find the optimal operating conditions, a designer must evaluate the ORC from different perspectives including thermodynamic performance, technological limits, economic viability, and environmental impact. A popular approach to include different criteria simultaneously is to formulate a bi-objective optimization problem. This type of multi-objective optimization (MOO) allows for finding a set of optimal design points by defining two different objectives. Once the optimization is completed, the decision-making analysis shall be carried out to identify the final design solution. This study aims to develop a decision-making tool for facilitating the choice of the optimal design point. The proposed procedure is coded in MATLAB based on the commonly used Technique for Order Preference by Similarity to Ideal Solution (TOPSIS). By providing t... [more]
8578. LAPSE:2023.26911
Real-Time Dispatch of Coupled Transmission and Distribution Systems within a Distributed and Cooperative Framework
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: distributed optimization, real-time dispatch, renewable energy resources, security-constrained economic dispatch
This paper presents a real-time dispatch strategy for coupled transmission and distribution systems within a distributed and cooperative control framework to maintain reliable and secure operation with minimum generation costs and maximum renewable energy consumption. The presented strategy transforms each distribution system into a dispatchable active source via an average-consensus-based active power control of renewable distributed energy resources (DERs) at the distribution level and then dispatches the active power reference of conventional generators as well as the distribution systems in a measurement-based way at a transmission level. The voltage fluctuation caused by the DER active power control is smoothened with a distributed voltage control method, which can also reduce the active power loss in the distribution systems. Compared to existing real-time dispatch strategies, the proposed strategy can eliminate security issues in the transmission system in a short time by regula... [more]
8579. LAPSE:2023.26910
Serial Switch Only Rectifier as a Power Conditioning Circuit for Electric Field Energy Harvesting
April 3, 2023 (v1)
Subject: Energy Management
Keywords: capacitance transducers, electromagnetic coupling, electromagnetic induction, energy harvesting, home area network
Because traditional electronics cannot directly use the alternating output voltage and current provided by electric field energy harvesters, harvesting systems require additional regulating and conditioning circuits. In this field, this work presents a conditioning circuit, called serial switch-only rectifier (SSOR) for low-voltage electric field energy harvesting (EFEH) applications. The proposed approach consists of a tubular topology harvester mounted on the outer jacket of a 230 V three-wires electrical cable (neutral, ground, and phase), in which terminals are connected to SSOR. We compare SSOR performance with classic electronic approaches, such as a full-bridge rectifier and voltage doubler. Experimental findings showed that the gathered energy by a 1 m cylindrical harvester increased in approximately 73.3% using the SSOR as a power management circuit. Experimental findings showed that the gathered energy by a 1 m cylindrical harvester increase in approximately 73.3% using the S... [more]
8580. LAPSE:2023.26909
The Effect of Fracturing Fluid Saturation on Natural Gas Flow Behavior in Tight Reservoirs
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: gas relative permeability, hydraulic fracturing, tight reservoirs, water saturation
Hydraulic fracturing becomes an essential method to develop tight gas. Under high injection pressure, fracturing fluid entering into the formation will reduce the flow channel. To investigate the influence of water saturation on gas flow behavior, this study conducted the gas relative permeability with water saturation and the flow rate with the pressure gradient at different water saturations. As the two dominant tight gas-bearing intervals, the Upper Paleozoic Taiyuan and Shihezi Formations deposited in Ordos Basin were selected because they are the target layers for holding vast tight gas. Median pore radius in the Taiyuan Formation is higher than the one in the Shihezi Formation, while the most probable seepage pore radius in the Taiyuan Formation is lower than the one in the Shihezi Formation. The average irreducible water saturation is 54.4% in the Taiyuan Formation and 61.6% in the Shihezi Formation, which indicates that the Taiyuan Formation has more movable water. The average... [more]
8581. LAPSE:2023.26908
Modeling the Future California Electricity Grid and Renewable Energy Integration with Electric Vehicles
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: electric vehicle, grid integration, Renewable and Sustainable Energy, utility power, vehicle-to-grid
This study focuses on determining the impacts and potential value of unmanaged and managed uni-directional and bi-directional charging of plug-in electric vehicles (PEVs) to integrate intermittent renewable resources in California in the year 2030. The research methodology incorporates the utilization of multiple simulation tools including V2G-SIM, SWITCH, and GridSim. SWITCH is used to predict a cost-effective generation portfolio to meet the renewable electricity goals of 60% in California by 2030. PEV charging demand is predicted by incorporating mobility behavior studies and assumptions charging infrastructure and vehicle technology improvements. Finally, the production cost model GridSim is used to quantify the impacts of managed and unmanaged vehicle-charging demand to electricity grid operations. The temporal optimization of charging sessions shows that PEVs can mitigate renewable oversupply and ramping needs substantially. The results show that 3.3 million PEVs can mitigate ove... [more]
8582. LAPSE:2023.26907
Projecting the Price of Lithium-Ion NMC Battery Packs Using a Multifactor Learning Curve Model
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: battery prices, lithium-ion NMC battery, multifactor learning curve
Renewable energy (RE) utilization is expected to increase in the coming years due to its decreasing costs and the mounting socio-political pressure to decarbonize the world’s energy systems. On the other hand, lithium-ion (Li-ion) batteries are on track to hit the target 100 USD/kWh price in the next decade due to economy of scale and manufacturing process improvements, evident in the rise in Li-ion gigafactories. The forecast of RE and Li-ion technology costs is important for planning RE integration into existing energy systems. Previous cost predictions on Li-ion batteries were conducted using conventional learning curve models based on a single factor, such as either installed capacity or innovation activity. A two-stage learning curve model was recently investigated wherein mineral costs were taken as a factor for material cost to set the floor price, and material cost was a major factor for the battery pack price. However, these models resulted in the overestimation of future pric... [more]
8583. LAPSE:2023.26906
A Proposed New Approach for the Assessment of Selected Operating Conditions of the High Voltage Cable Line
April 3, 2023 (v1)
Subject: Modelling and Simulations
Keywords: cable line, energy systems analysis, mathematical modeling, numerical simulation, power grid
Calculation models for the selection of cable lines used for expansion and modernization in the energy system and energy transmission planning are recognized tools supporting decision-making in both the energy sector and energy policy. At the same time, the above calculation models contain a large number of correction factors taking into account the temperature of the external environment at various points, the mutual influence of which is not taken into account. This means limitations to today’s common approaches to solutions, especially with regard to the required safety buffer for cable line selection. To meet this challenge, this article presents a parameter that takes into account the change and difference in temperature at various points in the external environment in the analyzed cable line systems. The purpose of this paper was to develop a new approach to the selection of a cable line in order to minimize failure during operation. For this purpose, possible temperature cases t... [more]
8584. LAPSE:2023.26905
Determination and Fire Analysis of Gob Characteristics Using CFD
April 3, 2023 (v1)
Subject: Modelling and Simulations
Keywords: coal fire, coal seam, Computational Fluid Dynamics, FDS, fire behavior
A laboratory-scale analysis using coal from an underground mine was carried out, emulating a mixture from the gob area in an actual mine, consisting of waste, coal, and free space for the flow of air. Experimental tests and computational fluid dynamics modelling were done to define and verify the behavior of the collapsed region in a time-dependent analysis. In addition, the characteristics of coal were defined, regarding the self-combustion, combustion rate, and pollutants generated in each stage of the fire. The results achieved are useful for determining the behavior of the collapsed area in full-scale conditions and to provide valuable information to study different scenarios of a potential fire in a real sublevel coal mine regarding how the heat is spread in the gob and how pollutants are generated.
8585. LAPSE:2023.26904
Study on Bearing Capacity of Tank Foundation with Alternatively Arranged Vortex-Compression Nodular Piles
April 3, 2023 (v1)
Subject: Process Design
Keywords: bearing capacity, composite foundation, tank foundation, vortex-compression nodular pile
Types of tapered piles are widely applied in tank foundation consolidation, but their inherent deficiencies in design and construction limit their further promotion. Vortex compression pile is a novel nodular pile. Compared with the traditional equal-section pile, vortex compression nodular pile is featured by stronger bearing capacity and slighter settlement. In this paper, the model test results showed that vortex compression nodular pile can greatly improve the bearing capacity and reduce the settlement. Through the finite element software ABAQUS analysis the bearing characteristics of equal-section pile foundation and vortex-compression nodular pile foundation were compared. The three-dimensional solid model was established by ABAQUS finite element software. The impact of cushion modulus, cushion thickness, vertical load, pile modulus, soil modulus around the pile on the bearing capacity of the vortex-compression nodular pile foundation were studied.
8586. LAPSE:2023.26903
The Nexus Between Convergence of Conventional and Renewable Energy Consumption in the Present European Union States. Explorative Study on Parametric and Semi-Parametric Methods
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: energy consumption, EU member states, renewable energy consumption, β-convergence, σ-convergence
Economic and social progress is directly and closely related to energy consumption. In the latest decades, there is a higher need to reduce energy consumption from conventional sources, replacing it with energy obtained from unconventional sources. The environmental concern is one of the objectives of the European economic policy, with a particular focus on renewable energy consumption and energy efficiency in order to lower the environmental impact. In this context, we analyzed energy consumption per capita and renewable energy consumption per capita in the EU with the help of parametric methods, using the β-convergence model, and semiparametric methods, using the σ-convergence model. In this research we proposed to study six analysis models of the period 1960−2015, based on the availability of data. We concluded that the EU states went through a convergence process in a slow pace of energy consumption per capita and renewable energy per capita, showing a convergence pattern. The resu... [more]
8587. LAPSE:2023.26902
Modified Biochar—A Tool for Wastewater Treatment
April 3, 2023 (v1)
Subject: Environment
Keywords: biochar, fertilizer, iron(III) phosphate, phosphorus, purification, recycling, Wastewater
Global deposits of concentrated phosphates, which are a necessary source for the production of phosphate fertilizers, are limited. These reserves keep getting thinner, and every day, large amounts of phosphorus end up in watercourses. In this study, we verified that modified biochar (saturated with FeCl3 solution and then neutralized with NaOH solution) can adsorb significant amounts of phosphorus from wastewater. Moreover, the agrochemical qualities of sludge water from a municipal wastewater treatment plant, struvite, phosphorus-saturated biochar, and iron(III) phosphate from a reused biochar filter were tested in this study. We determined the amount of mobile phosphorus as well as the amount of extractable phosphorus and its five fractions. It was found that modified biochar can hold one-third of the phosphorus amount contained in the commonly used agricultural fertilizer simple superphosphate (1 × 105 g of modified biochar captures up to 2.79 × 103 g of P). Moreover, plants can mor... [more]
8588. LAPSE:2023.26901
Differences of Flow Patterns and Pressure Pulsations in Four Prototype Pump-Turbines during Runaway Transient Processes
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: differences, flow patterns, pressure pulsations, pump-turbine, runaway transient process, S-shaped characteristics, similarities
Frequent working condition conversions in pumped-storage power stations often induce stability problems, especially when the operating point enters the S-shaped region, during which flow transitions and pressure fluctuations are serious. The pump-turbines with different specific speed values show different characteristics, but their differences in stability features are still not clear. In this study, four different pump-turbines were selected to simulate the runaway processes from turbine modes. The similarities and differences of flow patterns and pressure fluctuations were analyzed. For the similarities, pressure pulsations increase gradually and fluctuate suddenly once the backflows occur at the runner inlets. For the differences, the evolutions of backflows and pressure pulsations are related to specific speeds and runner shapes. Firstly, it is easier for the lower specific speed turbines to enter the reverse pump mode. Secondly, the blade lean angle influences the position where... [more]
8589. LAPSE:2023.26900
A Converter with Automatic Stage Transition Control for Inductive Power Transfer
April 3, 2023 (v1)
Subject: Process Control
Keywords: automatic stage transition, efficiency, energy injection, inductive power transfer, soft switching condition
An automatic stage transition converter for an inductive power transfer system is presented in this paper. An effective control strategy with two working stages of independent energy injection stage and free resonance stage is employed in the proposed converter. With the automatic stage transition strategy, when the frequency of the resonance network changes, the ending time of the free resonance stage is automatically determined. At the same time, the phase angle of the free resonance stage is automatically set as half a resonant cycle. As the stage transition is not triggered by the switches, the switch motion can be executed in advance of the transition moments. Time margins are offered for every switch in the converter, which make the switching moments of the switches flexible and the control simple. Another feature of this converter is that during the energy injection stage, the energy is injected into the inductor independently. Therefore, the input power can be easily regulated... [more]
8590. LAPSE:2023.26899
Emission Measurement of Buses Fueled with Biodiesel Blends during On-Road Testing
April 3, 2023 (v1)
Subject: Energy Systems
Keywords: biodiesel, PEMS, RME, SORT, transit bus, UCOME
Increasing the biodiesel content of diesel fuels is encouraged because of its reduced carbon footprint. Pure rapeseed methyl ester (RME)and used cooking oil methyl ester (UCOME) are characterised by well-to-tank greenhouse gas (GHG) reductions of 54% and 88% compared to pure B0 petrodiesel, respectively. Captive fleets such as public transport buses could benefit from these GHG reductions by increasing the biodiesel content of their fuel because they have a consequent yearly fuel consumption. The aim of this paper is to compare on-road tailpipe emissions of a diesel bus when increasing the biodiesel concentration in the fuel. The tests were carried out on a standard city bus belonging to the Euro V EEV emission standard that was equipped with a portable emission measurement system measuring NO, NO2, PN, CO and CO2 at the tailpipe. The bus followed the SORT which is representative of urban bus driving. The heavy urban on-road measurements indicated increased NOx emissions (24−26%), decr... [more]
8591. LAPSE:2023.26898
The Economic Value of Wind Energy Nowcasting
April 3, 2023 (v1)
Subject: Energy Management
Keywords: balancing strategies, electricity market, nowcasting, wind energy forecasting
In recent years, environmental concerns resulted in an increase in the use of renewable resources such as wind energy. However, high penetration of the wind power is a challenge due to the intermittency of this resource. In this context, the wind energy forecasting has become a major issue. In particular, for the end users of wind energy forecasts, a critical but often neglected issue is the economic value of the forecast. In this work, we investigate the economic value of forecasting from 30 min to 3 h ahead, also known as nowcasting. Nowcasting is mainly used to inform trading decisions in the intraday market. Two sources of uncertainty affecting wind farm revenues are investigated, namely forecasting errors and price variations. The impact of these uncertainties is assessed for six wind farms and several balancing strategies using market data. Results are compared with the baseline case of no nowcasting and with the idealized case of perfect nowcast. The three settings show signific... [more]
8592. LAPSE:2023.26897
Catalytic Electrochemical Water Splitting Using Boron Doped Diamond (BDD) Electrodes as a Promising Energy Resource and Storage Solution
April 3, 2023 (v1)
Subject: Materials
Keywords: BDD, boron doped diamond, CuO NPs, Energy Storage, water splitting, ZnO NPs
The present study developed a new system of electrochemical water splitting using a boron doped diamond (BDD) electrode in the electrochemical reactor. The new method assessed the electrical current, acidity (pH), electrical conductivity, absorbance, dissipation, and splitting energies in addition to the water splitting efficiency of the overall process. Employing CuO NPs and ZnO NPs as catalysts induced a significant impact in reducing the dissipated energy and in increasing the efficiency of splitting water. Specifically, CuO NPs showed a significant enhancement in reducing the dissipated energy and in keeping the electrical current of the reaction stable. Meanwhile, the system catalyzed with ZnO NPs induced a similar impact as that for CuO NPs at a lower rate only. The energy dissipation rates in the system were found to be 48% and 65% by using CuO and ZnO NPs, respectively. However, the dissipation rate for the normalized system without catalysis (water buffer at pH = 6.5) is known... [more]
[0.17 s]

