Browse
Records Added in April 2023
Records added in April 2023
Change month: January | February | March | April | May | June | July | August | September | October | November | December
8093. LAPSE:2023.27396
Reduced-Scale Models of Variable Speed Hydro-Electric Plants for Power Hardware-in-the-Loop Real-Time Simulations
April 4, 2023 (v1)
Subject: Modelling and Simulations
Keywords: ‘Hill Charts’, hydro-electric plant, power hardware-in-the-loop, real-time simulation, reduced-scale model, testing and validation, variable speed operation
Variable Speed Hydro-Electric Plant (VS-HEP) equipped with power electronics has been increasingly introduced into the hydraulic context. This paper is targeting a VS-HEP Power Hardware-In-the-Loop (PHIL) real-time simulation system, which is dedicated to different hydraulic operation schemes tests and control laws validation. Then, a proper hydraulic model will be the key factor for building an efficient PHIL real-time simulation system. This work introduces a practical and generalised modelling hydraulic modelling approach, which is based on ‘Hill Charts’ measurements provided by industrial manufacturers. The hydraulic static model is analytically obtained by using mathematical optimization routines. In addition, the nonlinear dynamic model of the guide vane actuator is introduced in order to evaluate the effects of the induced dynamics on the electric control performances. Moreover, the reduced-scale models adapted to different laboratory conditions can be established by applying sc... [more]
8094. LAPSE:2023.27395
Application of Perovskite Layer to Rotor for Enhanced Stator-Rotor Capacitance for PMSM Shaft Voltage Reduction
April 4, 2023 (v1)
Subject: Other
Keywords: adjustable speed drive, bearing voltage ratio, common mode voltage, electric discharge machining bearing currents, shaft voltage
Adjustable speed drives use Pulse Width Modulation (PWM) to switch DC-bus voltage for the synthesis of three-phase voltages to provide power to the permanent magnet synchronous motor (PMSM). This switching action produces very short rise and fall times and Common Mode Voltage (CMV) in the motor winding, exciting the parasitic capacitances inherent to the motor geometry. These parasitic capacitances give rise to shaft voltage due to a voltage divider action. Therefore, in this paper, first, motor parasitic capacitances and voltage divider action is explained. Second, the Barium Titanate (BTO) layer is coated onto the rotor to enhance stator-to-rotor compound capacitance and a simulation is performed showing the dependence of the shaft voltage on the permittivity of the perovskite (BTO) layer. The rotor BTO layer reduces the bearing voltage ratio as well. Third, experimental results are presented showing effectiveness of the application of the BTO layer to rotor and reduction of shaft vo... [more]
8095. LAPSE:2023.27394
Field Test of Wind Power Output Fluctuation Control Using an Energy Storage System on Jeju Island
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: energy storage system, fluctuation control, Renewable and Sustainable Energy, small power system, wind power generation
At present, renewable energy installations are expanding to solve both environmental problems and expensive energy fuel import prices in isolated areas. However, in a small-scale power system, rapid output fluctuations of renewable energy may cause power quality problems such as voltage and frequency fluctuations in the power system. To solve this problem, the local government of Jeju Island in South Korea implemented a megawatt (MW)-class pilot project to stabilize the output power of wind turbines using an energy storage system (ESS). In this project, a 0.5 MWh lithium-ion battery was connected to a 3 MW wind turbine via 1 MW power conversion system (PCS). In this paper, the field test results were divided into four categories as follows. First, the performance of stabilizing the output of the wind turbine using ESS was confirmed. Second, the control performance of the ESS was confirmed when the wind turbine suddenly stopped due to an accident. Third, it was confirmed that the ESS di... [more]
8096. LAPSE:2023.27393
Development of a Coupled TRNSYS-MATLAB Simulation Framework for Model Predictive Control of Integrated Electrical and Thermal Residential Renewable Energy System
April 4, 2023 (v1)
Subject: Process Control
Keywords: building optimization, energy optimization, genetic algorithm optimization, global pattern search optimization, HVAC-building MPC, optimizer performance analysis, Particle Swarm Optimization, residential prosumer, self-consumption, whitebox MPC
An integrated electrical and thermal residential renewable energy system consisting of solar thermal collectors, gas boiler, fuel cell combined heat and power, a photovoltaic system with battery, inverter, and thermal storage for a single-family house of Sonnenhaus standard is investigated with a model predictive controller (MPC). The main focus of this article is to define a multi-objective mathematical function, develop a coupled simulation framework for the nonlinear time-varying deterministic discrete-time problem of the energy system using TRNSYS and MATLAB. With the developed methodology, a sensitivity analysis of maximum optimization time, swarm (or population or mesh) size of a typical spring day and a typical summer day assuming a 100% accurate weather and load forecast with three different algorithms: particle swarm optimization (PSO), genetic algorithm (GA) and global pattern search (GPS) are analyzed. Finally, the obtained results are compared with a status quo controller.... [more]
8097. LAPSE:2023.27392
Influence of the Calcination Temperature of Synthetic Gypsum on the Particle Size Distribution and Setting Time of Modified Building Materials
April 4, 2023 (v1)
Subject: Materials
Keywords: calcination process, Fraunhofer method, particle size distribution, setting time, synthetic gypsum
The paper assesses the influence of the calcination temperature of synthetic gypsum binder on the binding properties of innovative gypsum pastes, as well as on masonry and plastering mortars. The calcination process of gypsum binder was carried out at four different temperatures ranging from 170 to 190 °C. The specimens for testing were prepared on the basis of the obtained raw material with a constant water to gypsum ratio of w/g = 0.75. It was noted that the calcination temperature influenced the setting time of the gypsum. Based on synthetic gypsum, mixtures of masonry and plastering mortars modified with tartaric acid and Plast Retard were designed. During the experiment, the particle diameter distribution of aqueous suspensions of building and synthetic gypsum particles (before and after calcination) was determined using the Fraunhofer laser method. The dimensions of the obtained artificial gypsum grains did not differ from the diameters of the gypsum grains in the reference sampl... [more]
8098. LAPSE:2023.27391
A Novel Electricity Theft Detection Scheme Based on Text Convolutional Neural Networks
April 4, 2023 (v1)
Subject: Numerical Methods and Statistics
Keywords: data-driven approaches, electricity theft detection, smart meters, text convolutional neural networks (TextCNN), time-series classification
Electricity theft decreases electricity revenues and brings risks to power usage’s safety, which has been increasingly challenging nowadays. As the mainstream in the relevant studies, the state-of-the-art data-driven approaches mainly detect electricity theft events from the perspective of the correlations between different daily or weekly loads, which is relatively inadequate to extract features from hours or more of fine-grained temporal data. In view of the above deficiencies, we propose a novel electricity theft detection scheme based on text convolutional neural networks (TextCNN). Specifically, we convert electricity consumption measurements over a horizon of interest into a two-dimensional time-series containing the intraday electricity features. Based on the data structure, the proposed method can accurately capture various periodical features of electricity consumption. Moreover, a data augmentation method is proposed to cope with the imbalance of electricity theft data. Exten... [more]
8099. LAPSE:2023.27390
The Identification of Hotspots in the Bioenergy Production Chain
April 4, 2023 (v1)
Subject: System Identification
Keywords: bioeconomy, bioenergy, biogas plant, energy return on investment, hotspot analysis, life cycle assessment
Increasing interest in bioenergy production in the context of the transition towards a circular economy and the promotion of renewable energy has produced demands for optimization of the value chain of energy production to improve the environmental viability of the system. Hotspot analysis based on life cycle assessment (LCA) contributes to the mitigation of environmental burdens and is a very important step towards the implementation of a bioeconomy strategy. In this study, hotspots identified using two parallel pathways: a literature review and empirical research on four different biogas plants located in Poland. LCA and energy return on investment (EROI) analysis of the whole bioenergy production chain were considered to identify unit processes or activities that are highly damaging to the environment. The biogas plants differ mainly in the type of raw materials used as an input and in the method of delivery. The results show that the most impactful processes are those in the delive... [more]
8100. LAPSE:2023.27389
Robust Decentralized Tracking Voltage Control for Islanded Microgrids by Invariant Ellipsoids
April 4, 2023 (v1)
Subject: Energy Management
Keywords: decentralized control, invariant set, islanded mode, microgrid, robust tracking
This manuscript presents a robust tracking (servomechanism) controller for linear time-invariant (LTI) islanded (autonomous, isolated) microgrid voltage control. The studied microgrid (MG) consists of many distributed energy resources (DERs) units, each using a voltage-sourced converter (VSC) for the interface. The optimal tracker design uses the ellipsoidal approximation to the invariant sets. The MG system is decomposed into different subsystems (DERs). Each subsystem is affected by the rest of the system that is considered as a disturbance to be rejected by the controller. The proposed tracker (state feedback integral control) rejects bounded external disturbances by minimizing the invariant ellipsoids of the MG dynamics. A condition to design decentralized controllers is derived in the form of linear matrix inequalities. The proposed controller is characterized by rapid transient response, and zero error in the steady state. A robustness analysis of the control strategy (against lo... [more]
8101. LAPSE:2023.27388
The Potential of Agricultural Biogas Production in Ukraine—Impact on GHG Emissions and Energy Production
April 4, 2023 (v1)
Subject: Food & Agricultural Processes
Keywords: agricultural biogas, bioenergy, biomethane, economic performance, GHG emission, regional analysis, Ukraine
Renewable energy production is gaining importance in the context of global climate changes. However, in some countries other aspects increasing the role of renewable energy production are also present. Such a country is Ukraine, which is not self-sufficient in energy supply and whose dependency on poorly diversified import of energy carriers regularly leads to political tensions and has socio-economic implications. Production of agricultural biogas seems to be a way to both slow down climatic changes and increase energy self-sufficiency by replacing or complementing conventional sources of energy. One of the most substantial barriers to agricultural biogas production is the low level of agricultural concentration and significant economies of scale in constructing biogas plants. The aim of the paper was thus to assess the potential of agricultural biogas production in Ukraine, including its impact on energy self-sufficiency, mitigation of greenhouse gas (GHG) emissions and the economic... [more]
8102. LAPSE:2023.27387
Resonant Combustion Start Considering Potential Energy of Free-Piston Engine Generator
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: combustion starting, free-piston engine, linear motor, mechanical energy, mechanical resonance, potential energy
Free-piston engine generators without a crank mechanism are expected to be used in series hybrid vehicles because of their lower losses. The series hybrid system requires a low starting thrust because the engine frequently starts depending on the battery state. This study clarifies the effectiveness of the constant thrust resonance starting method that utilizes the compression pressure of the engine and the spring thrust. The piston must pass the combustion starting point with a predetermined speed to start combustion. Herein, we present a thrust setting method that uses the energy state diagram to optimize the velocity at the combustion start point. A simulation is performed assuming output when mounted on a vehicle. Consequently, the simulation results show that the maximum thrust can be reduced by more than 90% compared to that without resonance. Moreover, the speed at the combustion start point is in agreement with the value obtained using an energy state diagram. An impulse-like c... [more]
8103. LAPSE:2023.27386
Aerodynamic Analysis of Coning Effects on the DTU 10 MW Wind Turbine Rotor
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: aerodynamic, cone, wind turbine
The size of wind turbine rotors is still rapidly increasing, though many technical challenges emerge. Novel rotor designs emerge to satisfy this up-scale trend, such as downwind load-aligned concepts, which orients the loads along the blade spanwise to greatly decrease the bending moments at the root. As the studies on the aerodynamics of these rotor concepts using 3D body-fitted mesh are very limited, this paper establishes different cone configurations based on the DTU 10 MW reference rotor and conducts a series of simulations. It is found that the cone angle and the distance from the blade section to the tip vortex are two deterministic factors on conning. Upwind rotors have larger power output, less thrust, smaller wake deficit, and smaller influencing area than downwind rotors of the same size, which provides superior aerodynamic priority and benefits wind farm design. The largest upwind cone angle of 14.03°, among the cases studied, leads to the highest torque to thrust ratio whi... [more]
8104. LAPSE:2023.27385
Renewable Energy Promotion Instruments Used by Innovation Brokers in a Technology Transfer Network. Case Study of the Enterprise Europe Network
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: development, efficiency, management, promotion, renewable energy sources
Stable and sustainable economic development—including that of renewable energy resources (RES)—requires institutional support of an environment that would enable market operations, and support them in case they are ineffective. Innovation brokers, including structured technology transfer networks, play a key role in promoting, disseminating, and liaising between the parties in the RES sector. The aim of the paper is to present the structure of events used to promote RES in Europe by the Enterprise Europe Network in the years 2017−2018; to verify whether the type of promotion instrument used is significantly related to the location of the events organized; to research whether the selection of the supporting partner is determined by the organized event’s geographical location. The analysis is carried out by means of an empirical study of the network of innovation brokers, i.e., the Enterprise Europe Network. Additionally, the available data are analyzed in terms of the type of the partne... [more]
8105. LAPSE:2023.27384
LES Analysis of CO Emissions from a High Pressure Siemens Gas Turbine Prototype Combustor at Part Load
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: carbon monoxide, finite rate chemistry (FRC), fuel staging, gas turbine, large-eddy simulations (LES), part load
This work contributes to the understanding of mechanisms that lead to increased carbon monoxide (CO) concentrations in gas turbine combustion systems. Large-eddy simulations (LES) of a full scale high pressure prototype Siemens gas turbine combustor at three staged part load operating conditions are presented, demonstrating the ability to predict carbon monoxide pollutants from a complex technical system by investigating sources of incomplete CO oxidation. Analytically reduced chemistry is applied for the accurate pollutant prediction together with the dynamic thickened flame model. LES results show that carbon monoxide emissions at the probe location are predicted in good agreement with the available test data, indicating two operating points with moderate pollutant levels and one operating point with CO concentrations below 10 ppm. Large mixture inhomogeneities are identified in the combustion chamber for all operating points. The investigation of mixture formation indicates that fue... [more]
8106. LAPSE:2023.27383
Co-Incineration of Rice Straw-Wood Pellets: A Sustainable Strategy for the Valorisation of Rice Waste
April 4, 2023 (v1)
Subject: Environment
Keywords: circular economy, co-incineration, rice straw
Agricultural activities produce an estimated amount of 32.7 MToe/year of residues in EU countries. They are mostly disposed in landfills, incinerated without any control, or abandoned in fields, causing severe impacts on human health and environment. Rice is one of the most consumed crops worldwide with an annual production of 782 million tons according to the Food and Agriculture Organization of the United Nations database. In this context, the EU-funded project LIFE LIBERNITRATE promotes the use of renewable residual sources (i.e., rice straw) to obtain new materials with an added value. The methodology is based on the incineration of rice straw in an own-designed and constructed valorization system. Rice straw/wood pellets are burned in optimized conditions to produce a maximized quantity of ashes with high silica content. These materials will be then used to treat water polluted with nitrates, representing an optimal example of circular economy strategy. In this work, the own-desig... [more]
8107. LAPSE:2023.27382
Prediction of Novel Humified Gas Turbine Cycle Parameters for Ammonia/Hydrogen Fuels
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: Alternative Fuels, ammonia/hydrogen blends, humified gas turbine, Renewable and Sustainable Energy
Carbon emissions reduction via the increase of sustainable energy sources in need of storage defines chemicals such as ammonia as one of the promising solutions for reliable power decarbonisation. However, the implementation of ammonia for fuelling purposes in gas turbines for industry and energy production is challenging when compared to current gas turbines fuelled with methane. One major concern is the efficiency of such systems, as this has direct implications in the profitability of these power schemes. Previous works performed around parameters prediction of standard gas turbine cycles showed that the implementation of ammonia/hydrogen as a fuel for gas turbines presents very limited overall efficiencies. Therefore, this paper covers a new approach of parameters prediction consisting of series of analytical and numerical studies used to determine emissions and efficiencies of a redesigned Brayton cycle fuelled with humidified ammonia/hydrogen blends. The combustion analysis was d... [more]
8108. LAPSE:2023.27381
Review of the Photothermal Energy Conversion Performance of Nanofluids, Their Applications, and Recent Advances
April 4, 2023 (v1)
Subject: Materials
Keywords: nanofluid, photothermal energy conversion performance, solar thermal collector, thermal properties, thermal system
Nanoparticles have been thoroughly investigated in the last few decades because they have many beneficial and functional qualities. Their capability to enhance and manipulate light absorption, thermal conductivity, and heat transfer efficiency has attracted significant research attention. This systematic and comprehensive work is a critical review of research on the photothermal energy conversion performance of various nanofluids as well as the recent advances in several engineering applications. Different nanofluids used in the photothermal energy conversion process were compared to identify the suitable applications of each nanofluid in thermal systems. An analysis of the previous investigations based on experimental and numerical studies has established that nanomaterials have the potential to increase the efficiency of solar thermal systems.
8109. LAPSE:2023.27380
PCB-Embedded Spiral Pattern Pick-Up Coil Current Sensor for WBG Devices
April 4, 2023 (v1)
Subject: Process Operations
Keywords: current sensor, multilayer PCB pattern coil, wide bandgap devices
This paper proposes a current sensor for wide bandgap (WBG) devices. The current of a power semiconductor device is mainly measured using a Rogowski coil, an active current transformer, and a coaxial shunt resistor. The Rogowski coil and active current transformer are not suitable for the current measurement of surface mount WBG devices due to their operating principle. The coaxial shunt resistor causes parasitic inductance. Since WBG devices are more sensitive to parasitic inductance than silicon devices, parasitic inductance may affect circuit operation. To overcome these problems, this paper proposes a printed circuit board (PCB)-embedded spiral pattern pick-up coil current measurement for WBG devices. The proposed pick-up coil has high mutual inductance compared to the conventional pick-up coil, so the measurement sensitivity is high. In addition, there is no need for additional processing outside the PCB. Experimental results using a double pulse tester circuit are provided to ver... [more]
8110. LAPSE:2023.27379
A Broadband Enhanced Structure-Preserving Reduced-Order Interconnect Macromodeling Method for Large-Scale Equation Sets of Transient Interconnect Circuit Problems
April 4, 2023 (v1)
Subject: Modelling and Simulations
Keywords: interconnect circuit, large scale equation set, model order reduction, transient response, wideband frequency
In the transient analysis of an engineering power electronics device, the order of its equivalent circuit model is excessive large. To eliminate this issue, some model order reduction (MOR) methods are proposed in the literature. Compared to other MOR methods, the structure-preserving reduced-order interconnect macromodeling (SPRIM) based on Krylov subspaces will achieve a higher reduction radio and precision for large multi-port Resistor-Capacitor-Inductor (RCL) circuits. However, for very wide band frequency transients, the performance of a Krylov subspace-based MOR method is not satisfactory. Moreover, the selection of the expansion point in this method has not been comprehensively studied in the literature. From this point of view, a broadband enhanced structure-preserving reduced-order interconnect macromodeling (SPRIM) method is proposed to reduce the order of equation sets of a transient interconnect circuit model. In addition, a method is introduced to determine the optimal exp... [more]
8111. LAPSE:2023.27378
Heat Transfer Performance of an Axially Rotating Heat Pipe for Cooling of Grinding
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: green grinding, heat transfer performance, rotating heat pipe, volume of fluid
Coolants are widely used to dissipate grinding heat in conventional grinding. This process, however, is not satisfactory as coolants often lose efficacy in grinding due to film boiling and can result in adverse health and environment effects. The present paper put forward the concept of a rotating heat pipe grinding wheel, attempting to reduce or eliminate the coolant amount and realize green machining. The heat transfer performance of rotating heat pipe grinding wheel was studied by using volume of fluid method in ANSYS/FLUENT. The influence of the input heat flux, filling ratio and rotational speed were investigated by a simulation method. Results show that the appropriate heat flux range for the rotating heat pipe grinding wheel was from 2000 to 100,000 W/m2, the ideal filling ratio was 50% and the rise of the rotational speed turned out to weaken the heat transfer coefficient. Finally, dry grinding experiments on Ti-6Al-4V were performed and the temperatures in both the rotating he... [more]
8112. LAPSE:2023.27377
Decompositions for MPC of Linear Dynamic Systems with Activation Constraints
April 4, 2023 (v1)
Subject: Process Control
Keywords: battery charging, Benders decomposition, EV, MPC, outer approximation
The interconnection of dynamic subsystems that share limited resources are found in many applications, and the control of such systems of subsystems has fueled significant attention from scientists and engineers. For the operation of such systems, model predictive control (MPC) has become a popular technique, arguably for its ability to deal with complex dynamics and system constraints. The MPC algorithms found in the literature are mostly centralized, with a single controller receiving the signals and performing the computations of output signals. However, the distributed structure of such interconnected subsystems is not necessarily explored by standard MPC. To this end, this work proposes hierarchical decomposition to split the computations between a master problem (centralized component) and a set of decoupled subproblems (distributed components) with activation constraints, which brings about organizational flexibility and distributed computation. Two general methods are considere... [more]
8113. LAPSE:2023.27376
Cation-Exchange Capacity Distribution within Hydrothermal Systems and Its Relation to the Alteration Mineralogy and Electrical Resistivity
April 4, 2023 (v1)
Subject: Materials
Keywords: alteration, cation-exchange capacity, clay minerals, electrical resistivity, hydrothermal systems, Iceland, image
Cation-exchange capacity (CEC) measurements are widely used to quantify the smectite content in altered rocks. Within this study, we measure the CEC of drill cuttings in four wells from three different high-temperature geothermal areas in Iceland. The CEC measurements in all four wells show similar depth/temperature related pattern, and when comparing the CEC with electrical resistivity logs, we could show that the low resistivity zone coincides with CEC values >5 meq/100 g. The measurements show, in general, an exponential decrease of the CEC with increasing depth. At the facies boundary between the mixed-layer clay and epidote-chlorite zone, the CEC reaches a steady state at about 5 meq/100 g and below that it only decreases slightly within a linear trend with increasing depth. The facies boundary overlaps with the transition where the electrical resistivity logs show an increase in resistivity. It is shown that the measured CEC can be related to the clay mineral alteration within th... [more]
8114. LAPSE:2023.27375
The Clean Energy Package and Demand Response: Setting Correct Incentives
April 4, 2023 (v1)
Subject: Energy Policy
Keywords: clean energy package, demand response, incentive regulation, network tariffs
We describe how recent EU regulation affects demand response (DR) and highlight some of the remaining regulatory challenges from a legal and economic viewpoint. With the Clean Energy Package (CEP), the EU has opted for a fully market-based, consumer-centered approach for DR. The development of business models and products is left to a large extent to market forces. However, to enable the efficient development of those DR markets, network regulation has to adapt. (1) Network tariffs have to become more cost-reflective to provide correct incentives to market participants. The capacity tariffs have to increase, net-metering should be abolished, and optional tariff components for providing flexibility may need to be considered. (2) The regulation for distribution system operators (DSOs) may need to be fine-tuned to reflect their new roles. We present three scenarios: (a) a horizontal merger of unbundled DSOs under incentive regulation, (b) a DSO as a subsidiary of an integrated utility und... [more]
8115. LAPSE:2023.27374
The Impact of Industry on European Union Emissions Trading Market—From Network Perspective
April 4, 2023 (v1)
Subject: Energy Management
Keywords: EU ETS, industry, network, trading
This study pioneers to investigate the impact of industry on the European Union carbon trading market based on network perspective. All the accounts in the European Union Emissions Trading System (EU ETS) are summarized at the industry level, and then the trading relationship between industries is constructed in the network layout. Based on this network, the centrality of each industry is measured—the industries of electricity, gas, steam and air conditioning supply (EGSAS), bank, broker, exchange, and wholesale trade excluding motor vehicles and motorcycles (WTEM) have higher centrality. Finally, the impact of industry on the evolution of networks is analyzed, Findings show that the financial intermediaries play important roles at the beginning of each phase, while their influences on the network will decrease as the market goes on. On the contrary, influences of some other industries like WTEM are gradually increasing.
8116. LAPSE:2023.27373
In Situ Wettability Investigation of Aging of Sandstone Surface in Alkane via X-ray Microtomography
April 4, 2023 (v1)
Subject: Other
Keywords: in situ porous media, wettability, X-ray microtomography
Wettability of surfaces remains of paramount importance for understanding various natural and artificial colloidal and interfacial phenomena at various length and time scales. One of the problems discussed in this work is the wettability alteration of a three-phase system comprising high salinity brine as the aqueous phase, Doddington sandstone as porous rock, and decane as the nonaqueous phase liquid. The study utilizes the technique of in situ contact angle measurements of the several 2D projections of the identified 3D oil phase droplets from the 3D images of the saturated sandstone miniature core plugs obtained by X-ray microcomputed tomography (micro-CT). Earlier works that utilize in situ contact angles measurements were carried out for a single plane. The saturated rock samples were scanned at initial saturation conditions and after aging for 21 days. This study at ambient conditions reveals that it is possible to change the initially intermediate water-wet conditions of the san... [more]
8117. LAPSE:2023.27372
Hydrodynamic Performance of a Hybrid System Combining a Fixed Breakwater and a Wave Energy Converter: An Experimental Study
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: breakwater, hybrid wave energy device, hydrodynamic performance, Wave Energy, wave tank experiments
In this paper, a hybrid system integrating a fixed breakwater and an oscillating buoy type wave energy converter (WEC) is introduced. The energy converter is designed to extract the wave power by making use of the wave-induced heave motions of the three floating pontoons in front of the fixed breakwater. A preliminary experimental study is carried out to discuss the hydrodynamic performance of the hybrid system under the action of regular waves. A scale model was built in the laboratory at Hohai University, and the dissipative force from racks and gearboxes and the Ampere force from dynamos were employed as the power take-off (PTO) damping source. During the experiments, variations in numbers of key parameters, including the wave elevation, free response or damped motion of the floating pontoons, and the voltage output of the dynamos were simultaneously measured. Results indicate that the wave overtopping and breaking occurring on the upper surfaces of floating pontoons have a signific... [more]
[0.15 s]

