Browse
Records Added in April 2023
Records added in April 2023
Change month: January | February | March | April | May | June | July | August | September | October | November | December
8118. LAPSE:2023.27371
Economic Viability of Renewable Energy Communities under the Framework of the Renewable Energy Directive Transposed to Austrian Law
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: Austria, beneficial composition of energy communities, clean energy package, economic viability, national transposition of guidelines for renewable energy communities, renewable energy communities, renewable energy directive, shared photovoltaics
This study is concerned with the national transposition of the European Renewable Energy Directive into Austrian law. The objective is to estimate the economic viability for residential customers when participating in a renewable energy community (REC), focused on PV electricity sharing. The developed simulation model considers the omission of certain electricity levies as well as the obligatory proximity constraint being linked to grid levels, thus introducing a stepwise reduction of per-unit grid charges as an incentive to keep the inner-community electricity transfer as local as possible. Results show that cost savings in residential RECs cover a broad range from 9 EUR/yr to 172 EUR/yr. The lowest savings are gained by customers without in-house PV systems, while owners of a private PV system make the most profits due to the possibility of selling as well as buying electricity within the borders of the REC. Generally, cost savings increase when the source is closer to the sink, as w... [more]
8119. LAPSE:2023.27370
Voltage Quality Enhancement of Grid-Integrated PV System Using Battery-Based Dynamic Voltage Restorer
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: converters, dynamic voltage restorer (DVR), photovoltaic systems, power distribution faults, power filters, state of charge (SOC)
The advancement of power electronic-based sensitive loads drives the power utilities’ devotion to power quality issues. The voltage disturbance could be happening due to fault conditions, switching of loads, energizing of transformers, or integration of highly intermittent energy sources such as PV systems. This research work attempts to enhance the voltage fluctuation of a sensitive load connected to a grid-integrated PV system using a battery-based dynamic voltage restorer (DVR). The proposed battery energy storage-based DVR has two separate controlling stages that are implemented at the DC−DC buck/boost converter of the battery and voltage source converter (VSC) system. Charging and discharging of the battery is operated based on the state-of-charge (SOC) value of the battery and the measured root mean square (RMS) voltage at the point of common coupling (PCC). The VSC of the DVR detection and reference generation control is done appropriately. In the detection control of the VSC, a... [more]
8120. LAPSE:2023.27369
Modeling of Axial Flux Permanent Magnet Generators
April 4, 2023 (v1)
Subject: Other
Keywords: axial flux machine, disk generator, permanent magnet, PM generator
This article focuses on modeling of an Axial Flux Permanent Magnet Generator (AFPMG). The authors analyzed selected variants of disk generators, including coreless stator constructions and with iron core ones, also taking into account the Permanent Magnet (PM) arrangement in order to show the way to obtain the optimal machine characteristics based on analytical equations. In addition to the full model, which takes into account the higher harmonics of the magnetic field distribution, the paper presents a simplified mathematical model developed for generator operation cases such as standalone, connected to a 3-phase power grid and loaded with a diode rectifier. The analytical and finite-element method (FEM) calculations were performed as well as laboratory tests to confirm the correctness of presented model assumptions.
8121. LAPSE:2023.27368
Distributed Energy Resources and the Application of AI, IoT, and Blockchain in Smart Grids
April 4, 2023 (v1)
Subject: Information Management
Keywords: automated services in microgrids, blockchain, cybersecurity, deep learning, distributed energy resources, electric vehicle as DER, electricity system networks, energy Internet, Internet of Things, Machine Learning, modern power system, peer to peer network, power infrastructure, renewable energy resources, resilience, smart grid services, smart microgrids
Smart grid (SG), an evolving concept in the modern power infrastructure, enables the two-way flow of electricity and data between the peers within the electricity system networks (ESN) and its clusters. The self-healing capabilities of SG allow the peers to become active partakers in ESN. In general, the SG is intended to replace the fossil fuel-rich conventional grid with the distributed energy resources (DER) and pools numerous existing and emerging know-hows like information and digital communications technologies together to manage countless operations. With this, the SG will able to “detect, react, and pro-act” to changes in usage and address multiple issues, thereby ensuring timely grid operations. However, the “detect, react, and pro-act” features in DER-based SG can only be accomplished at the fullest level with the use of technologies like Artificial Intelligence (AI), the Internet of Things (IoT), and the Blockchain (BC). The techniques associated with AI include fuzzy logic,... [more]
8122. LAPSE:2023.27367
Drivers behind Residential Electricity Demand Fluctuations Due to COVID-19 Restrictions
April 4, 2023 (v1)
Subject: Numerical Methods and Statistics
Keywords: behaviour, COVID-19, demand, Energy, energy literacy, household, human-computer interaction
The COVID-19 pandemic rapidly reoriented the lives of billions of people across the globe toward working, learning, and subsisting from home. This paper examines the consequences of this disruption of electricity use in Australian households. Using high-frequency electricity monitoring from 491 houses and per-circuit monitoring and in-depth interviews with 17 households, the paper (1) compares changes in energy use before and during COVID-19 lockdown, (2) quantifies the key drivers of changes in energy use experienced by households during lockdown, and (3) tracks households’ interactions with energy use feedback. The findings identify significant increases in certain aspects of household electricity use directly related to COVID-19, including increased cooking and digital device use. Yet despite the government mandate requiring a large proportion of the population to remain at home, overall energy use among the majority of Queensland households monitored actually decreased during lockd... [more]
8123. LAPSE:2023.27366
Soot Particle Size Distribution, Regulated and Unregulated Emissions of a Diesel Engine Fueled with Palm Oil Biodiesel Blends
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: engine load, palm oil biodiesel, regulated emissions, unregulated emissions
In this study, five fuels including pure diesel (B0), pure palm oil biodiesel (B100), and their blends (B10, B20, and B30) were investigated in relation to soot particle distribution and regulated and unregulated emission characteristics in a common rail direct injection (CRDI) diesel engine. The results indicated that CO, hydrocarbon (HC), and particulate matter (PM) regulated emissions were effectively controlled to a very low level by combining the addition of palm oil biodiesel (POB) to diesel with optimized engine operating conditions. Paper filters and TEM grids were used to capture the diesel particles. All the PM primary particles were less than 100 nm in diameter observed by TEM, and the average diameters of the PM primary particles for the biodiesel blends were distributed between 20 and 26 nm. Unregulated emissions such as trace metals including Pb, Mn, and Ba were found in the PM particles, and the xylene, toluene, and benzene unregulated emissions of B100 were reduced by 5... [more]
8124. LAPSE:2023.27365
A Concept of Integration of a Vactrain Underground Station with the Solidarity Transport Hub Poland
April 4, 2023 (v1)
Subject: Process Design
Keywords: hyperloop, hyperloop station building, low-pressure high-speed trains, spatial design, vactrain, vacuum tube high-speed train
This paper provides an analysis of a designed underground station infrastructure for vacuum tube high-speed trains for the planned mega transport hub in Poland. The potential of integrating the infrastructure of the station building with sealed low-pressure tubes system is analyzed. The Solidarity Transport Hub Poland is a planned mega hub to be located in Baranów Municipality, Poland, which is comprised of an airport, an airport city, a road, and railway infrastructure. It is to be integrated with the first route of vactrains in Poland. The aim of this paper is to design a hyperloop station building adequate for the advanced technology of low-pressure high-speed trains. Designing a hyperloop station is not trivial, due to technological aspects which have not been hitherto present in airport or railway planning and design, such as low-pressure zones or airlocks which determine possible passenger paths and evacuation roads. Both the mega airport and Polish hyperloop are in the planning... [more]
8125. LAPSE:2023.27364
CO2 Foam and CO2 Polymer Enhanced Foam for Heavy Oil Recovery and CO2 Storage
April 4, 2023 (v1)
Subject: Materials
Keywords: CO2 foam, CO2 storage, fractured reservoir, heavy oil recovery, polymer enhanced foam
Enhanced oil recovery (EOR) from heavy oil reservoirs is challenging. High oil viscosity, high mobility ratio, inadequate sweep, and reservoir heterogeneity adds more challenges and severe difficulties during any EOR method. Foam injection showed potential as an EOR method for challenging and heterogeneous reservoirs containing light oil. However, the foams and especially polymer enhanced foams (PEF) for heavy oil recovery have been less studied. This study aims to evaluate the performance of CO2 foam and CO2 PEF for heavy oil recovery and CO2 storage by analyzing flow through porous media pressure profile, oil recovery, and CO2 gas production. Foam bulk stability tests showed higher stability of PEF compared to that of surfactant-based foam both in the absence and presence of heavy crude oil. The addition of polymer to surfactant-based foam significantly improved its dynamic stability during foam flow experiments. CO2 PEF propagated faster with higher apparent viscosity and resulted i... [more]
8126. LAPSE:2023.27363
Experimental Analysis and CFD Modeling for Conventional Basin-Type Solar Still
April 4, 2023 (v1)
Subject: Modelling and Simulations
Keywords: CFD ANSYS, Egyptian climate, solar still, thermal desalination
With the rising population, environmental pollution, and social development, potable water is reducing and being contaminated day by day continually. Thus, several researchers have focused their studies on seas and oceans in order to get potable fresh water by desalination of their saltwater. Solar still of basin type is one of the available technologies to purify water because of free solar energy. The computational fluid dynamic CFD model of the solar still can significantly improve means for optimization of the solar still structure because it reduces the need for conducting large amount of experiments. Therefore, the main purpose of this study is presenting a multi-phase, three-dimensional CFD model, which predicts the performance of the solar still without using any experimental measurements, depending on the CFD solar radiation model. Simulated results are compared with experimental values of water and glass cover temperatures and yield of fresh water in climate conditions of She... [more]
8127. LAPSE:2023.27362
Comparative Studies on Water- and Vapor-Based Hydrothermal Carbonization: Process Analysis
April 4, 2023 (v1)
Subject: Materials
Keywords: hydrochar, hydrothermal carbonization (HTC), phase distribution of water, process conditions, reactor pressure, solid contents, vapothermal carbonization (VTC)
Hydrothermal carbonization (HTC) reactor systems used to convert wet organic wastes into value-added hydrochar are generally classified in the literature as liquid water-based (HTC) or vapor-based (VTC). However, the distinction between the two is often ambiguous. In this paper, we present a methodological approach to analyze process conditions for hydrothermal systems. First, we theoretically developed models for predicting reactor pressure, volume fraction of liquid water and water distribution between phases as a function of temperature. The reactor pressure model predicted the measured pressure reasonably well. We also demonstrated the importance of predicting the condition at which the reactor system enters the subcooled compression liquid region to avoid the danger of explosion. To help understand water−feedstock interactions, we defined a new solid content parameter %S(T) based on the liquid water in physical contact with feedstock, which changes with temperature due to changes... [more]
8128. LAPSE:2023.27361
Mechanisms and Applications of Pressure Relief by Roof Cutting of a Deep-Buried Roadway near Goafs
April 4, 2023 (v1)
Subject: Modelling and Simulations
Keywords: deep coal mine, roadway near goaf, roof cutting and pressure relief, similarity simulation
Affected by high ground stress, the surrounding rock control of a roadway is one of the most important factors restricting the utilization of deep resources. Therefore, it is necessary to propose a method to improve the stress environment of the deep-buried roadway and reduce its deformation. The article focuses on the 121,302 machine roadway in Kouzidong coal mine to analyze the large deformations of roadways near goafs (RNGs) in deep coal mines and reveal the mechanisms related to pressure relief via roof cutting. Through physical simulation, overburdened structures and the migration laws of RNGs in deep coal mines are studied, and the overburdened RNGs will eventually have a double short-arm “F”-type suspended roof structure. The superposition movement of the structure is the prime cause for the large deformation of the RNGs considered here. Artificial roof cutting can weaken the superposition effect of the double “F” structure and induce the roof to produce a new fracture. Meanwhil... [more]
8129. LAPSE:2023.27360
Exploring the Charge Compensation Mechanism of P2-Type Na0.6Mg0.3Mn0.7O2 Cathode Materials for Advanced Sodium-Ion Batteries
April 4, 2023 (v1)
Subject: Materials
Keywords: charge compensation mechanism, electronic structure, P2-tpye oxides, sodium-ion batteries, X-ray absorption spectroscopy
P2-type sodium layered transition metal oxides have been intensively investigated as promising cathode materials for sodium-ion batteries (SIBs) by virtue of their high specific capacity and high operating voltage. However, they suffer from problems of voltage decay, capacity fading, and structural deterioration, which hinder their practical application. Therefore, a mechanistic understanding of the cationic/anionic redox activity and capacity fading is indispensable for the further improvement of electrochemical performance. Here, a prototype cathode material of P2-type Na0.6Mg0.3Mn0.7O2 is comprehensively investigated, which presents both cationic and anionic redox behaviors during the cycling process. By a combination of soft X-ray absorption spectroscopy and electroanalytical methods, we unambiguously reveal that only oxygen redox reaction is involved in the initial charge process, then both oxygen and manganese participate in the charge compensation in the following discharge proc... [more]
8130. LAPSE:2023.27359
Smooth-Switching Control of Robot-Based Permanent-Magnet Synchronous Motors via Port-Controlled Hamiltonian and Feedback Linearization
April 4, 2023 (v1)
Subject: Process Control
Keywords: feedback linearization, hamiltonian, robot, smooth-switching
To solve the contradiction between dynamic performance and steady-state performance of the robot system, a smooth-switching control strategy is proposed. By combining robot and motor model, the complete model of the robot driving system is established. The single-loop Feedback Linearization (FL) controller and Port-Controlled Hamiltonian (PCH) controller based on the complete model are derived to ensure the rapidity and stability of the system respectively. A smooth-switching function based on position error is designed. It can ensure the smooth-switching between two controllers and avoid the instability caused by switch-switching. The proposed algorithm can make the robot system have good dynamic and steady performance. Simulation and experiment results demonstrate the effectiveness of the smooth-switch control strategy.
8131. LAPSE:2023.27358
The Performance of a Spectral Wave Model at Predicting Wave Farm Impacts
April 4, 2023 (v1)
Subject: Environment
Keywords: environmental impacts, numerical modeling, spectral wave models, wave energy converters, wave farms
For renewable ocean wave energy to support global energy demands, wave energy converters (WECs) will likely be deployed in large numbers (farms), which will necessarily change the nearshore environment. Wave farm induced changes can be both helpful (e.g., beneficial habitat and coastal protection) and potentially harmful (e.g., degraded habitat, recreational, and commercial use) to existing users of the coastal environment. It is essential to estimate this impact through modeling prior to the development of a farm, and to that end, many researchers have used spectral wave models, such as Simulating WAves Nearshore (SWAN), to assess wave farm impacts. However, the validity of the approaches used within SWAN have not been thoroughly verified or validated. Herein, a version of SWAN, called Sandia National Laboratories (SNL)-SWAN, which has a specialized WEC implementation, is verified by comparing its wave field outputs to those of linear wave interaction theory (LWIT), where LWIT is theo... [more]
8132. LAPSE:2023.27357
Mechanical-Level Hardware-In-The-Loop and Simulation in Validation Testing of Prototype Tower Crane Drives
April 4, 2023 (v1)
Subject: Other
Keywords: control system, crane drive, hardware in the loop testing, measurement, permanent magnet motor
In this paper, the static and dynamic simulations, and mechanical-level Hardware-In-the-Loop (MHIL) laboratory testing methodology of prototype drive systems with energy-saving permanent-magnet electric motors, intended for use in modern construction cranes is proposed and described. This research was aimed at designing and constructing a new type of tower crane by Krupiński Cranes Company. The described research stage was necessary for validation of the selection of the drive system elements and confirmation of its compliance with applicable standards. The mechanical construction of the crane was not completed and unavailable at the time of testing. A verification of drive system parameters had to be performed in MHIL laboratory testing, in which it would be possible to simulate torque acting on the motor shaft. It was shown that the HIL simulation for a crane may be accurate and an effective approach in the development phase. The experimental tests of selected operating cycles of pro... [more]
8133. LAPSE:2023.27356
An Improved Inverse-Time Over-Current Protection Method for a Microgrid with Optimized Acceleration and Coordination
April 4, 2023 (v1)
Subject: Optimization
Keywords: coordination optimization, distributed generation, inverse-time over-current protection, microgrid
This paper presents an improved inverse-time over-current protection method based on the compound fault acceleration factor and the beetle antennae search (BAS) optimization method for a microgrid. The proposed method can not only significantly increase the operation speed of the inverse-time over-current protection but also improve the protection coordination by considering the possible influential factors in terms of microgrid operation modes, distributed generation (DG) integration status, fault types, and positions, which are marked as the most challenging problems for over-current protection of a microgrid. In this paper, a new Time Dial Setting (TDS) of inverse-time protection is developed by applying a compound fault acceleration factor, which can notably accelerate the speed of protection by using low-voltage and short-circuit impedance during the fault. In order to improve the protection coordination, the BAS algorithm is then used to optimize the protection parameters of the... [more]
8134. LAPSE:2023.27355
Magnetic Coupling for a 10 kW Tidal Current Turbine: Design and Small Scale Experiments
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: counter-rotating turbine, cylindrical air gap magnetic coupling, marine current turbine, tidal current energy
This paper presents a coupling design that improves water tightness of a marine current turbine (MCT). The coupling is numerically analyzed and incorporated into the design of an MCT from a previous study. The performance of the MCT with the magnetic coupling is compared to the previous results in small scale turbine experiments. The results show that the new design is water tight and has lower mechanical losses when compared with previous results. The new turbine has increased maximum power output (from 116 W to 122 W) and hydrodynamic coefficient of power (Previously 0.45 to 0.46). Using these results, the coupling design is scaled for a 10 kW MCT and further analyzed by finite element analysis. The results obtained show that the magnetic coupling is capable of withstanding the combined weight of the hub and blade assembly. The results in this study will be used for developing a prototype for deployment in real seas.
8135. LAPSE:2023.27354
Estimation of the Heat Loss Coefficient of Two Occupied Residential Buildings through an Average Method
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: average method, building envelope’s in-use energy performance, heat loss coefficient
The existing performance gap between the design and the real energy consumption of a building could have three main origins: the occupants’ behaviour, the performance of the energy systems and the performance of the building envelope. Through the estimation of the in-use Heat Loss Coefficient (HLC), it is possible to characterise the building’s envelope energy performance under occupied conditions. In this research, the estimation of the HLC of two individual residential buildings located in Gainsborough and Loughborough (UK) was carried out using an average method. This average method was developed and successfully tested in previous research for an occupied four-story office building with very different characteristics to individual residential buildings. Furthermore, one of the analysed residential buildings is a new, well-insulated building, while the other represents the old, poorly insulated semidetached residential building typology. Thus, the monitored data provided were filter... [more]
8136. LAPSE:2023.27353
Thermal and Energy Performance Assessment of the Prefab Electric Ondol System for Floor Heating in a Residential Building
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: heating cost, heating energy, prefab electric Ondol system, residential building, thermal performance
In South Korea, radiant floor heating has been used from old housing to the recently constructed residential buildings, which is called “Ondol”. The Ondol system is generally a water-based system and it uses hot water as a heat medium provided by boilers fueled by natural gas. With great effort to reduce greenhouse gas emissions, electric Ondol panels have been increasingly applied to the recent residential buildings for floor heating. While the prefab electric Ondol panels were developed with the demand for dry construction method, the information about the prefab electric Ondol system is not sufficient. For the present study, the thermal performance of the prefab electric Ondol panels was investigated through field measurement. In addition, the heating energy and economic performance of the electric panel were compared with the conventional Ondol system. As a result, a significant surface temperature difference was observed. Moreover, the heating cost for the prefab electric Ondol sy... [more]
8137. LAPSE:2023.27352
Building 1D and 3D Mechanical Earth Models for Underground Gas Storage—A Case Study from the Molasse Basin, Southern Germany
April 4, 2023 (v1)
Subject: Modelling and Simulations
Keywords: geomechanical model, HM coupled modeling, Molasse Basin, underground gas storage
Hydromechanical models of gas storage in porous media provide valuable information for various applications ranging from the prediction of ground surface displacements to the determination of maximum reservoir pressure and storage capacity to maintain fault stability and caprock integrity. A workflow to set up such models is presented and applied to a former gas field in southern Germany for which transformation to a gas storage site is considered. The workflow comprises 1D mechanical earth modeling (1D MEM) to calculate elastic properties as well as a first estimate for the vertical and horizontal stresses at well locations by using log data. This information is then used to populate a 3D finite element model (3D MEM) which has been built from seismic data and comprises not only the reservoir but the entire overburden up to the earth’s surface as well as part of the underburden. The size of this model is 30 × 24 × 5 km3. The pore pressure field has been derived from dynamic fluid flow... [more]
8138. LAPSE:2023.27351
Photovoltaic Concentration: Research and Development
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: acceptance angle, concentrated photovoltaic, concentration, concentration ratio, efficiency, optical efficiency, primary optics, secondary optics
Concentrator Photovoltaic (CPV) technology, by using efficient optical elements, small sizes and high efficiency multi-junction solar cells, can be seen as a bright energy source to produce more cost-effective electricity. The main and basic idea is to replace the use of expensive solar cells with less expensive optical elements made from different materials. This paper aims to give to the readers a rapid and concise overview of CPV and the main characteristics to be considered when designing a CPV system. It reviews the main optical configurations presented in the literature, their advantages and drawbacks, as well as the recent progress in the concentration ratio and the major performances achieved in the field. The paper considers the more recent works, their optical designs, as well as their optical and electrical performances. It also relates the major achievements on the industrial side with the major milestones in CPV developments.
8139. LAPSE:2023.27350
Enhancing Oil Recovery with Hydrophilic Polymer-Coated Silica Nanoparticles
April 4, 2023 (v1)
Subject: Materials
Keywords: crude oil recovery, flow diversion, interfacial tension, polymer-coated nanoparticles, wettability alteration
Nanoparticles (NPs) have been proposed for enhanced oil recovery (EOR). The research has demonstrated marvelous effort to realize the mechanisms of nanoparticles EOR. Nevertheless, gaps still exist in terms of understanding the nanoparticles-driven interactions occurring at fluids and fluid−rock interfaces. Surface-active polymers or other surface additive materials (e.g., surfactants) have shown to be effective in aiding the dispersion stability of NPs, stabilizing emulsions, and reducing the trapping or retention of NPs in porous media. These pre-requisites, together with the interfacial chemistry between the NPs and the reservoir and its constituents, can result in an improved sweep efficiency. This paper investigates four types of polymer-coated silica NPs for the recovery of oil from water-wet Berea sandstones. A series of flooding experiments was carried out with NPs dispersed at 0.1 wt.% in seawater in secondary and tertiary oil recovery modes at ambient conditions. The dynamic... [more]
8140. LAPSE:2023.27349
Outdoor Air-Cooling System for a Computer Room and Its Corresponding Energy-Saving Effect
April 4, 2023 (v1)
Subject: Environment
Keywords: computer room, energy saving, field application, outdoor air-cooling system
The recent expansion of the internet network and rapid advancements in information and communication technology are expected to lead to a significant increase in power consumption and the number of data centers. However, these data centers consume a considerable amount of electric power all year round, regardless of working days or holidays; thus, energy saving at these facilities has become essential. A disproportionate level of power consumption is concentrated in computer rooms because air conditioners in these rooms are required to operate throughout the year to maintain a constant indoor environment for stable operation of computer equipment with high-heat release densities. Considerable energy-saving potential is expected in such computer rooms, which consume high levels of energy, if an outdoor air-cooling system and air conditioners are installed. These systems can reduce the indoor space temperature by introducing a relatively low outdoor air temperature. Therefore, we studied... [more]
8141. LAPSE:2023.27348
An Optimal Energy Optimization Strategy for Smart Grid Integrated with Renewable Energy Sources and Demand Response Programs
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: demand response programs, multi-objective energy optimization, photovoltaic, renewable energy sources, smart grid, Wind
An energy optimization strategy is proposed to minimize operation cost and carbon emission with and without demand response programs (DRPs) in the smart grid (SG) integrated with renewable energy sources (RESs). To achieve optimized results, probability density function (PDF) is proposed to predict the behavior of wind and solar energy sources. To overcome uncertainty in power produced by wind and solar RESs, DRPs are proposed with the involvement of residential, commercial, and industrial consumers. In this model, to execute DRPs, we introduced incentive-based payment as price offered packages. Simulations are divided into three steps for optimization of operation cost and carbon emission: (i) solving optimization problem using multi-objective genetic algorithm (MOGA), (ii) optimization of operating cost and carbon emission without DRPs, and (iii) optimization of operating cost and carbon emission with DRPs. To endorse the applicability of the proposed optimization model based on MOGA... [more]
8142. LAPSE:2023.27347
Cooling Panel with Integrated PCM Layer: A Verified Simulation Study
April 4, 2023 (v1)
Subject: Modelling and Simulations
Keywords: cooling panel, Energy Storage, overheating, passive cooling, PCM, TABS
The focus of this research paper is to develop a verified simulation model for a cooling panel with integrated phase-change materials (PCMs)—a stainless steel panel filled with PCM and integrated hydronic piping circuit. This solution is targeted for passive cooling of residential buildings in Baltic Sea region that experience overheating for most of the year due to highly insulated building envelopes and extensive glazing—a phenomena for nearly zero energy buildings (NZEBs). This approach aims to maintain comfortable indoor temperature all year round by passive means—free-cooling, adiabatic (evaporative) cooling or limited mechanical cooling. The simulations are performed with IDA ICE 4.8 and the measurements for simulation model verification are collected from a test chamber. The results show that reasonable agreement can be reached for simulated and experimentally measured data.
[0.08 s]

