A nonlinear reduced-order state observer is applied to estimate the degree of polymerization in a series of polycondensation reactors. The finishing stage of polyethylene terephthalate synthesis is considered in this work. This process has a special structure of lower block triangular form, which is properly utilized to facilitate the calculation of the state-dependent gain in the observer design. There are two possible on-line measurements in each reactor. One is continuous, and the other is slow-sampled with dead time. For the slow-sampled titration measurement, inter-sample behavior is estimated from an inter-sample output predictor, which is essential in providing continuous corrections on the observer. Dead time compensation is carried out in the same spirit as the Smith predictor to reduce the effect of delay in the measurement outputs. By integrating the continuous-time reduced-order observer, the inter-sample predictor and the dead time compensator together, the degree of polym... [more]

This study aimed to develop optimal microwave assisted extraction conditions for recovery of phenolic compounds and antioxidant properties from the macadamia skin, an abundant waste source from the macadamia industry. Water, a safe, accessible, and inexpensive solvent, was used as the extraction solvent and Response Surface Methodology (RSM) was applied to design and analyse the conditions for microwave-assisted extraction (MAE). The results showed that RSM models were reliable for the prediction of extraction of phenolic compounds and antioxidant properties. Within the tested ranges, MAE radiation time and power, as well as the sample-to-solvent ratio, affected the extraction efficiency of phenolic compounds, flavonoids, proanthocyanidins, and antioxidant properties of the macadamia skin; however, the impact of these variables was varied. The optimal MAE conditions for maximum recovery of TPC, flavonoids, proanthocyanidins and antioxidant properties from the macadamia skin were MAE ti... [more]

Kinetic modeling of the bulk copolymerization of d-limonene (Lim) and n-butyl acrylate (BA) at 80 °C was performed using PREDICI®. Model predictions of conversion, copolymer composition and average molecular weights are compared to experimental data at five different feed compositions (BA mol fraction = 0.5 to 0.9). The model illustrates the significant effects of degradative chain transfer due to the allylic structure of Lim as well as the intramolecular chain transfer mechanism due to BA.

Developing “good” membrane modules and materials is a key step towards reducing the cost of membrane-based CO2 capture. While this is traditionally being done through incremental development of existing and new materials, this paper presents a new approach to identify membrane materials with a disruptive potential to reduce the cost of CO2 capture for six potential industrial and power generation cases. For each case, this approach first identifies the membrane properties targets required to reach cost-competitiveness and several cost-reduction levels compared to MEA-based CO2 capture, through the evaluation of a wide range of possible membrane properties. These properties targets are then compared to membrane module properties which can be theoretically achieved using 401 polymeric membrane materials, in order to highlight 73 high-potential materials which could be used by membrane development experts to select materials worth pushing towards further development once practical conside... [more]

This work is a meta-study of CO2 capture processes for coal and natural gas power generation, including technologies such as post-combustion solvent-based carbon capture, the integrated gasification combined cycle process, oxyfuel combustion, membrane-based carbon capture processes, and solid oxide fuel cells. A literature survey of recent techno-economic studies was conducted, compiling relevant data on costs, efficiencies, and other performance metrics. The data were then converted in a consistent fashion to a common standard (such as a consistent net power output, country of construction, currency, base year of operation, and captured CO2 pressure) such that a meaningful and direct comparison of technologies can be made. The processes were compared against a standard status quo power plant without carbon capture to compute metrics such as cost of CO2 emissions avoided to identify the most promising designs and technologies to use for CO2 emissions abatement.

Two process designs for the separation section of a flexible dimethyl ether and methanol polygeneration plant are presented, as well as an optimization method which can determine the optimal design under market uncertainty quickly and to global optimality without loss of model fidelity. The polygeneration plant produces a product mixture that is either mostly dimethyl ether or mostly methanol depending on market conditions by using a classic two-stage dimethyl ether production catalytic reaction route in which the second stage is bypassed when the market demand is such that methanol production is more favorable than dimethyl ether. The downstream distillation sequence is designed to purify the products to desired specifications despite the wide variability in feed condition that corresponds to the upstream reaction system operating either in DME-rich or methanol-rich mode. Because the optimal design depends on uncertain market conditions (realized as the percentage of the time in which... [more]