The scouring by a tidal turbine is investigated by using a joint theoretical and experimental approach in this work. The existence of a turbine obstructs a tidal flow to divert the flow passing through the narrow channel in between the blades and seabed. Flow suppression is the main cause behind inducing tidal turbine scouring, and its accelerated velocity is being termed as tip-bed velocity (Vtb). A theoretical equation is currently proposed to predict the tip-bed velocity based on the axial momentum theory and the conservation of mass. The proposed tip-bed velocity equation is a function of four variables of rotor radius (r), tip-bed clearance (C), efflux velocity (V0) and free flow velocity (V∞), and a constant of mass flow coefficient (Cm) of 0.25. An experimental apparatus was built to conduct the scour experiments. The results provide a better understanding of the scour mechanism of the horizontal axis tidal turbine-induced scour. The experimental results show that the scour dept... [more]

Sustainable liquid fuels will be needed for decades to fulfil the world’s growing energy demands. Combustion systems must be able to operate with a variety of renewable and sustainable fuels. This study focused on how the use of various alternative fuels affects combustion, especially in-cylinder combustion. The study investigated light fuel oil (LFO) and six alternative liquid fuels in a high-speed, compression-ignition (CI) engine to understand their combustion properties. The fuels were LFO (baseline), marine gas oil (MGO), kerosene, rapeseed methyl ester (RME), renewable diesel (HVO), renewable wood-based naphtha and its blend with LFO. The heat release rate (HRR), mass fraction burned (MFB) and combustion duration (CD) were determined at an intermediate speed at three loads. The combustion parameters seemed to be very similar with all studied fuels. The HRR curve was slightly delayed with RME at the highest load. The combustion duration of neat naphtha decreased compared to LFO as... [more]

To solve the problem of the low utilization ratio of clean renewable energy in public institutions, the basic information of energy utilization in public institutions was investigated. The suitability of passive energy use in public institutions was studied. According to the basic information and evaluation index of passive energy utilization in public institutions, the suitability of different types of passive energy (solar and geothermal energy) was studied by combining the resource conditions in different climate zones and the characteristics of energy utilization in typical public institutions, and the suitability distribution map was formed. In terms of research methods, the CRITIC (Criteria Importance Though Intercrieria Correlation) method based on the characteristics of objective data, and the natural breakpoint method based on the structure of objective data, were selected. Based on the climatic zoning of the buildings, this study conducted a suitability zoning. Each climatic... [more]

The necessity of transport electrification is already undeniable due to, among other facts, global Greenhouse Gas (GHG) emissions and fossil-fuel dependency. In this context, electric vehicles (EVs) play a fundamental role. Such vehicles are usually seen by the network as simple loads whose needs have to be supplied. However, they can contribute to the correct operation of the network or a microgrid and the provision of ancillary services and delay the need to reinforce the power lines. These concepts are referred to as Vehicle-to-Grid (V2G), Vehicle-to-Building (V2B) and Vehicle-to-Home (V2H). In paper, a deep classification and analysis of published charging strategies is provided. In addition, optimal charging strategies must minimise the degradation of the batteries to increase their lifetime, since it is considered that the life of a battery ends when its capacity is reduced by 20% with respect to its nominal capacity. Therefore, an optimal integration of EVs must consider both gr... [more]

The significant penetration of renewables, in the Hellenic electricity system, during the last 12 years, was based on feed-in tariff-supporting schemes, according to the compliance to European Directives. The characteristics of this penetration are presented and analyzed in this paper based on real data. Photovoltaics, wind parks, hydroelectric plants, biomass-driven plants, and cogeneration systems are examined. The cost of the feed-in tariff incentives is qualified and analyzed. Simple but effective models are proposed to describe renewable seasonal variation: (a) A simple cosine model adequately describes the seasonal performance of various renewable technologies in terms of capacity factor; (b) a smart seasonal model based on the separation between winter and summer consumption activities (both following normal distributions) adequately describes the electricity consumption profile. The predicted values of renewable shares using the proposed models were also validated with historic... [more]

This study investigated the effects of H2 and CH4 concentrations on the ignition delay time and laminar flame speed during the combustion of CH4/H2 and multicomponent syngas mixtures using a novel constructed reduced syngas chemical kinetics mechanism. The results were compared with experiments and GRI Mech 3.0 mechanism. It was found that mixture reactivity decreases and increases when higher concentrations of CH4 and H2 were used, respectively. With higher H2 concentration in the mixture, the formation of OH is faster, leading to higher laminar flame speed and shorter ignition delay time. CH4 and H2 concentrations were calculated at different pressures and equivalence ratios, showing that at high pressures CH4 is consumed slower, and, at different equivalence ratios CH4 reacts at different temperatures. In the presence of H2, CH4 was consumed faster. In the conducted two-stage sensitivity analysis, the first analysis showed that H2/CH4/CO mixture combustion is driven by H2-based reac... [more]

The building sector accounts for one third of the global energy consumption and it is expected to grow in the next decades. This evidence leads researchers, engineers and architects to develop innovative technologies based on renewable energies and to enhance the thermal performance of building envelopes. In this context, the potential applicability and further energy performance analysis of these technologies when implemented into different building typologies and climate conditions are not easily comparable. Although massive information is available in data sources, the lack of standardized methods for data gathering and the non-public availability makes the comparative analyses more difficult. These facts limit the benchmarking of different building energy demand parameters such as space heating, cooling, air conditioning, domestic hot water, lighting and electric appliances. Therefore, the first objective of this study consists in providing a review about the common typologies of r... [more]

DC to AC inverters are the well-known and improved in various kinds photovoltaic (PV) and gird tied systems. However, these inverters are require interfacing transformers to be synchronized with the grid-connected system. Therefore, the system is bulky and not economy. The transformerless inverter (TLI) topologies and its grid interface techniques are increasingly engrossed for the benefit of high efficiency, reliability, and low cost. The main concern in the TL inverters is common mode voltage (CMV), which causes the switching-frequency leakage current, grid interface concerns and exaggerates the EMI problems. The single-phase inverter two-level topologies are well developed with additional switches and components for eliminating the CMV. Multilevel inverters (MLIs) based grid connected transformerless inverter topology is being researched to avail additional benefits from MLI, even through that are trust topologies presented in the literature. With the above aim, this paper has propo... [more]

The share of global CO2 emissions deriving from the cement industry is about 5%. More than 50% of these are process-related and cannot be avoided. This paper addresses the application of CO2 capture technology to the cement industry. Analyses focusing on post-combustion technology for cement plants are carried out on the basis of detailed model calculations. Different heat supply variants for the regeneration of loaded wash solution were investigated. CO2 avoidance costs are in a range of 77 to 115 EUR/tCO2. The achievable CO2 avoidance rate for the investigated cases was determined to be 70% to 90%. CO2 reduction potentials were identified using CCS technology, focusing on the German cement industry as a case study. The results show that adopting carbon capture technology could lead to a significant reduction in CO2 emissions.

Doubly-fed induction generators (DFIGs) are widely used in wind energy conversion systems. The dynamic features of DFIGs make it important to focus on designing high-performance control schemes. However, the dynamic characteristics of such generators depend on nonlinear parameters, such as stator flux, stator current, and rotor current, which increase the overall system complexity. In addition, the DFIG Wind Energy Conversion Systems (WECSs) size is growing beyond 7 MW, which increases stress on both the mechanical drive train and the power circuits during connection to the grid. Such stress and dynamic features cannot be neglected. Therefore, robust controllers must be implemented which have the ability to support the dynamic frequencies of wind energy to ensure system stability in grid connection mode and during subsequent use. Conventional vector control configurations that use proportional-integral controllers have various drawbacks, such as parameter tuning difficulties, mediocre... [more]

The Chang 7 reservoir in Changqing oilfield is rich in tight oil. However, due to the low formation permeability, it is very difficult to obtain economical oil production without stimulation treatments. Volume fracturing seems to be a more efficient tight oil recovery enhancement (EOR) method in Chang 7 pilot tests compared with conventional hydraulic fracturing. In this study, Chang 7 tight oil reservoir was first characterized by its geological property, hydrocarbon source rock distribution, and formation physiochemical property. Tight core flooding tests were then conducted to experimentally investigate the EOR ability of the volume fracturing technique. The field-scale practice was also demonstrated and analyzed. The results show that Chang 7 reservoir is favorable for the generation of a large amount of tight oil. Fractures created in tight cores can significantly improve the fluid flow conductivity and enhance the imbibition of displacing water, resulting in a greater tight oil r... [more]

The purpose of this paper is to improve the utilization of renewable energy by exergy and exergoeconomic analysis of the novel combined cooling, heating, and power (CCHP) system, which is based on solar thermal biomass gasification. The source of heat to assist biomass and steam gasification is the solar heat collected by a dish collector, and the product gas being fuel that drives the internal combustion engine to generate electricity and then to produce chilled/hot water by a waste heat unitization system. The analysis and calculation of the exergy loss and exergy efficiency of each component reveal the irreversibility in the heating and cooling conditions. Then, the exergoeconomic costs of multi-products such as electricity, chilled water, heating water, and domestic hot water are calculated by using the cost allocation method based on energy level. The influencing factors of the unit exergy cost of products are evaluated by sensitivity analysis, such as initial investment cost, bio... [more]

Low-field nuclear magnetic resonance (NMR) has been widely used in the petroleum industry for reservoir evaluation. Fluid properties and petrophysical parameters can be determined from NMR spectra, obtained from processing echo data measured from the NMR tool. The more accurate NMR spectra are, the higher the reliability of reservoir evaluation based on NMR logging is. The purpose of this paper is to obtain more precise T1−T2 spectra in heavy oil reservoirs, with focus on the T1−T2 data acquisition and inversion. To this end, four inversion algorithms were tested on synthetic T1−T2 data, their precision was evaluated and the optimal inversion algorithm was selected. Then, the sensitivity to various acquisition parameters (wait time and echo spacing) was evaluated with T1−T2 experiments using a disordered accumulation of glass beads with a diameter of 45 μm saturated with heavy oil and distilled water. Finally, the sensitivity to various inversion parameters (convergence tolerance, maxi... [more]

This paper presents a study on the energy efficiency and emissions of a converted high-revolution bore 79.5 mm/stroke 95 mm engine with a conventional fuel injection system for operation with dual fuel feed: diesel (D) and natural gas (NG). The part of NG energy increase in the dual fuel is related to a significant deterioration in energy efficiency ( η i ) , particularly when engine operation is in low load modes and was determined to be below 40% of maximum continuous rating. The effectiveness of the D injection timing optimisation was established in high engine load modes within the range of a co-combustion ratio of NG ≤   0.4: with an increase in η i , compared to D, the emissions of NO x + HC decreased by 15%   to   25%, while those of CO 2 decreased by 8% to16%; the six-fold CO emission increase, up to 6 g/kWh, was unregulated. By referencing the indicated process characteristics of the established... [more]

In this paper, based on stochastic optimization methods, a technique for optimal sizing of battery energy storage systems (BESSs) under wind uncertainties is provided. Due to considerably greater penetration of renewable energy sources, BESSs are becoming vital elements in microgrids. Integrating renewable energy sources in a power system together with a BESS enhances the efficiency of the power system by enhancing its accessibility and decreasing its operating and maintenance costs. Furthermore, the microgrid-connected BESS should be optimally sized to provide the required energy and minimize total investment and operation expenses. A constrained optimization problem is solved using an optimization technique to optimize a storage system. This problem of optimization may be deterministic or probabilistic. In case of optimizing the size of a BESS connected to a system containing renewable energy sources, solving a probabilistic optimization problem is more effective because it is not po... [more]

Integration of wind energy into the grid faces a great challenge regarding power quality. The International Electrotechnical Commission (IEC) 61400-21 standard defines the electrical characteristics that need to be assessed in a Wind Turbine (WT), as well as the procedure to measure the disturbances produced by the WT. One of the parameters to be assessed are voltage fluctuations or flicker. To estimate the flicker emission of a Wind Power Plant (WPP), the standard establishes that a quadratic exponent should be used in the summation of the flicker emission of each WT. This exponent was selected based on studies carried out in WPPs with type I and II WTs. Advances in wind turbine technology have reduced their flicker emission, mainly thanks to the implementation of power electronics for the partial or total management of the power injected into the grid. This work is based on measurements from a WPP with 16 type III WTs. The flicker emission of a single WT and of the WPP were calculate... [more]

Electrifying the energy system with heat pumps and battery electric vehicles (BEV) is a strategy of Switzerland and many other countries to reduce CO2 emissions. A large electrification, however, poses several new challenges for the electricity system, particularly in combination with a simultaneous substitution of nuclear power plants (NPP) by volatile renewables such as photovoltaics (PV). In this study, these challenges in terms of additional electricity demands, deficits and surpluses as well as effective CO2 mitigation are assessed in a dynamic and data-driven approach. To this end, electricity demand and production profiles are synthesized based on measured data and specifications and assumptions of the key technologies at a high temporal resolution. The additional electricity demand of heat pumps is estimated from hourly measured heat demand profiles of a Swiss district heating provider, while for BEV different recharging patterns are combined. For electricity production, NPP ar... [more]

This paper presents wind tunnel tests on the wake characteristics of a three-blade horizontal axis wind turbine and the wake effect on the performance of a downstream turbine. For a single turbine model, the performance was determined and this was followed by measurement of the wind characteristics including velocities, turbulence intensities, and correlation in the wake flow field. Subsequently, taking two horizontal axis wind turbines in a tandem arrangement into account, their performance was tested and the aerodynamic mechanism was discussed. The results showed that the upstream turbine with blades set at a small pitch angle provided smaller disturbance to the flow, but as the blade turned faster, larger changes in the velocity and the turbulence intensity occurred in its wake due to the more frequent disturbance of the wind turbine. The correlation of wake velocities in the turbine swept area also obviously decreased from the free-stream situation. For the downstream turbine, the... [more]

The direct current circuit breakers are considered a promising option to protect the transmission line against commonly appearing line-to-ground fault. However, the challenges of losses in the nonoperational stage, escalation of response against fault current, and large fault current handling capability remain the debatable issues for direct current circuit breakers. This paper introduces a novel topology of the hybrid circuit breaker with fault-current-limiting characteristics, which contains three branches: the main branch, fault-current-limiting branch, and energy absorption branch. The main branch includes a mechanical switch, breaker impedance, and bidirectional power electronics switches. In the fault-current-limiting branch, a fault-current-limiting circuit is introduced which contains n numbers of bidirectional switches and current-limiting inductors, which are connected in series to make the design modular in nature. During the normal working stage, the current flows through t... [more]

China has set stringent fuel consumption rate (FCR) targets to address the serious environmental and energy security problems caused by vehicles. Estimating the technological progress and tradeoffs between FCR and vehicle attributes is important for assessing the viability of meeting future targets. In this paper, we explored the relationship between vehicle FCR and other attributes using a regression model with data from 2009−2016. We also quantified the difference in the tradeoff between local and joint venture brands. The result showed that from 2009 to 2016, if power and curb mass were held constant, 2.3% and 2.9% annual technological progress should have been achieved for local and joint venture brands, respectively. The effectiveness of fuel-efficient technologies for joint venture brands is generally better than that of local brands. Impacts of other attributes on FCR were also assessed. The joint venture brands made more technological progress with FCR improvement than that of... [more]

Residents’ willingness to use green energy products is a major concern for different stakeholders and policymakers due to the reformed Chinese electricity market since 2015. This study focused on the Chinese consumer’s willingness to opt and pay for environmentally-friendly electricity sources in Shanghai’s residential sector. A questionnaire survey was used to find out the influence of gender, age, education, awareness and income level on consumers’ attitudes to alter their energy sources to green ones. The results indicated that income level and awareness are significant barriers in the usage of green energy products. Increasing the respondent’s awareness about the issues of non-green energy products convinced 97% of them to change their electricity sources completely or partly, in line with their monthly income. This clearly shows that clarifying the benefits of green energy products is a key tool to achieve a green environment in China.

Waste heat recovery (WHR) from exhaust gases in natural gas engines improves the overall conversion efficiency. The organic Rankine cycle (ORC) has emerged as a promising technology to convert medium and low-grade waste heat into mechanical power and electricity. This paper presents the energy and exergy analyses of three ORC−WHR configurations that use a coupling thermal oil circuit. A simple ORC (SORC), an ORC with a recuperator (RORC), and an ORC with double-pressure (DORC) configuration are considered; cyclohexane, toluene, and acetone are simulated as ORC working fluids. Energy and exergy thermodynamic balances are employed to evaluate each configuration performance, while the available exhaust thermal energy variation under different engine loads is determined through an experimentally validated mathematical model. In addition, the effect of evaporating pressure on the net power output, thermal efficiency increase, specific fuel consumption, overall energy conversion efficiency,... [more]

The recent growing attention to energy saving and environmental protection issues has brought attention to the possibility of exploiting syngas from gasification of biomass and coal for the firing of industrial plants included in the, so called, Integrated Gasification Combined Cycle power plants. In order to improve knowledge on the employ of syngas in lean premixed turbulent flames, a large scale swirl stabilized gas-turbine burner has been operated with a simplified model of H2 enriched syngas from coal gasification. The experimental campaign has been performed at atmospheric pressure, with operating conditions derived from scaling the real gas turbines. The results are reported here and consist of OH-PLIF (OH Planar Laser Induced Fluorescence) measurements, carried out at decreasing equivalence of air/fuel ratio conditions and analysed together with the mean aerodynamic characterisation of the burner flow field in isothermal conditions obtained through LDV (Laser Doppler Velocimetr... [more]

Advanced building envelopes targeting high energy performance should combine high thermal performance with easy and fast installation. The combination of lightweight steel-framed building systems with vacuum insulation panels (VIPs) form an attractive solution toward this requirement. In the present study, a lightweight metal frame drywall building insulated with VIPs is constructed and experimentally/theoretically investigated, focusing on the impact of every type of thermal bridges on the thermal performance of the envelope and its upgrade due to the presence of the VIPs at the walls. Temperature measurements obtained at several locations of the envelope, over a period of one year, are presented and analyzed. The results are in agreement with the theoretical values and demonstrate that the VIPs can reduce the thermal transmittance of the central part of the wall by ca. 50%, limiting the impact of metal studs. The paper discusses the impact of dimensional inaccuracies and damaged pane... [more]

This paper reports on the effects of different load profiles on the transient behavior of a polymer electrolyte fuel cell (PEFC). A protocol of six tests, each with different current density ramps, was conducted. The corresponding cell voltage, pressure drop response, and ohmic resistance were then experimentally investigated. The time-dependent voltage profiles were applied to represent the cell performance. The cathodic pressure drop and ohmic resistance were utilized to analyze the water dynamic behavior inside the cell. The voltage overshoot and undershoot behavior were observed throughout the experiment. It was found that with an increase of the current change rates, the magnitude of voltage over/undershoots also increased. When the holding time at the constant current density was zero, the overshoot or undershoot behavior disappeared. The results of the pressure drop analysis showed that the load ramp did not have a significant effect on the average pressure drop in the tests. Du... [more]