Low-salinity water flooding (LSWF) is environment-friendly and operates similarly to conventional waterflooding without the need for synthetic chemical materials. The application of LSWF makes sense in Vietnam as HC production has steadily declined since 2002, and the majority of main oil fields have become near mature and mature fields. In the next years, Enhanced Oil Recovery (EOR) should be a top priority for Petro Vietnam to boost its oil production, for which the key issue is how to select a suitable EOR technology. In this study, LSWF of the Lower Miocene sand using low salinity water from Lower Oligocene sand was investigated. Previously at the Ruby field in the Cuu Long Basin, an LSWF feasibility study was carried out based on a conventional core flooding experiment, which is time-consuming and costly. This study targets the Chim Sao field in the Nam Con Son Basin, for which a cheaper and faster assessing method is required. As a result, a numerical code written in Matlab was d... [more]

Perovskite solar cells (PVSC) have drawn increasing attention due to their high photovoltaic performance and low-cost fabrication with solution processability. A variety of methods have been developed to make uniform and dense perovskite thin films, which play a critical role on device performance. Herein, we demonstrate a polymer additive assisted approach with Polyamidoamine (PAMAM) dendrimers to facilitate the growth of uniform, dense, and ultra-smooth perovskite thin films. Furthermore, a lamp annealing approach has been developed to rapidly anneal perovskite films using an incandescent lamp, resulting in comparable or even better device performance compared to the control hotplate annealing. The facile polymer additive assisted method and the rapid lamp annealing technique offer a clue for the large-scale fabrication of efficient PVSCs.

The influence of the briquetting process on SO2 and NO release characteristics, combustion properties and kinetic characteristics during biomass combustion was investigated. Two biomass (Wheat straw and Tree bulk) and two obtained briquettes were analysed. The briquetting process helps to prevent the release of SO2 and NO. The experimental results show that once the biomass is made into a briquette, when the reaction temperature is 900 ∘C, the sulphur release ratio for TB was reduced from 34.7% to 4.3% and for WS was reduced from 12.4% to 1.6%. When the reaction temperature increases to 1000 ∘C, the sulphur release ratio for TB was reduced from 73.4% to 30.4%, for WS it was reduced from 58.4% to 10.2%. SEM micrographs show that the compact structure of the TB-Briquette and WS-Briquette reduce the rate of SO2 and NO release during combustion. The thermogravimetry confirmed that the combustion performance of WS-Briquette is the best, while the TB-Briquette is the worst. According to the... [more]

The paper presents data from a monthly campaign studying the elemental composition of PM10, as measured by a specific receptor in Kotórz Mały (Opole Voivodeship)—located in the vicinity of a moderately inhabited rural area—measured in one-hour samples using a Horiba PX-375 analyzer. The hourly variability of SO2, NO, NO2, CO, and O3 concentrations, as well as the variability of meteorological parameters, was also determined. On average, during the entire measurement period, the elements related to PM10 can be arranged in the following order: As < V < Ni < Pb < Cr < Mn < Cu < Ti < Zn < K < Fe < Ca < Al < Si < S. Trace elements, including toxic elements—such as As, V, Ni, Pb, Cr, and Mn—were present in low concentrations, not exceeding 10 ng/m3 (average daily value). These elements had fairly even concentrations, both daily and hourly. The concentrations of the main elements in the PM10, as measured by the receptor, are subject to strong hourly c... [more]

This paper presents a novel single-phase (SP) active-neutral point clamped (ANPC) five-level bidirectional converter (FLBC) for enhancing the power quality (PQ) during the grid-to-vehicle (G2V) and vehicle-to-grid (V2G) operation of an electric vehicle (EV) charger connected in series. This EV charger is based on a dual-active half-bridge DC-DC converter (DAHBC) with a high frequency isolation transformer. Unlike the comparable ANPC topologies found in literature, the proposed one has two more switches, i.e., ten instead of eight. However, with the addition of these components, the proposed multilevel converter not only becomes capable of properly balancing the voltage of the DC-link split capacitors under various step-changing conditions but it achieves a better efficiency, a lower stress of the switching devices and a more even distribution of the power losses. The resulting grid-tied ANPC-SPFLBC and DAHBC are accurately controlled with a cascaded control strategy and a single-phase... [more]

Accurate estimation of crude oil Bubble Point Pressure (Pb) plays a vital rule in the development cycle of an oil field. Bubble point pressure is required in many petroleum engineering calculations such as reserves estimation, material balance, reservoir simulation, production equipment design, and optimization of well performance. Additionally, bubble point pressure is a key input parameter in most oil property correlations. Thus, an error in a bubble point pressure estimate will definitely propagate additional error in the prediction of other oil properties. Accordingly, many bubble point pressure correlations have been developed in the literature. However, they often lack accuracy, especially when applied for global crude oil data, due to the fact that they are either developed using a limited range of independent variables or developed for a specific geographic location (i.e., specific crude oil composition). This research presents a utilization of the state-of-the-art Bayesian opt... [more]

Countries worldwide must dramatically reduce their emissions to achieve the goal of limiting temperature increases in line with the Paris Agreement. Involving developing countries in global actions on emission reduction will greatly enhance the effectiveness of global warming mitigation. This study investigated the feasibility of establishing a wind farm at four onshore and three offshore sites in Indonesia. Installing wind turbines with the highest hub height, largest rotor diameter, and lowest cut-in and rated wind speed in an identified area off Wetar Island presented the highest time-based availability and a capacity factor of 46%, as well as the highest power-based availability at 76%. The levelized cost of electricity at 0.082 USD/kWh was comparable to that of power generated from fossil fuels, which ranges from 0.07 to 0.15 USD/kWh in Indonesia. Increasing the feed-in-tariff for wind power from the current 0.08 USD/kWh would provide sufficient incentive for investment. Moving su... [more]

Coal seam gas (CSG), also known as coalbed methane (CBM), is an important source of gas supply to the liquefied natural gas (LNG) exporting facilities in eastern Australia and to the Australian domestic market. In late 2018, Australia became the largest exporter of LNG in the world. 29% of the country’s LNG nameplate capacity is in three east coast facilities that are supplied primarily by coal seam gas. Six geological basins including Bowen, Sydney, Gunnedah, Surat, Cooper and Gloucester host the majority of CSG resources in Australia. The Bowen and Surat basins contain an estimated 40Tcf of CSG whereas other basins contain relatively minor accumulations. In the Cooper Basin of South Australia, thick and laterally extensive Permian deep coal seams (>2 km) are currently underdeveloped resources. Since 2013, gas production exclusively from deep coal seams has been tested as a single add-on fracture stimulation in vertical well completions across the Cooper Basin. The rates and reserves... [more]

Rechargeable power sources are an essential element of large-scale energy systems based on renewable energy sources. One of the major challenges in rechargeable battery research is the development of electrode materials with good performance and low cost. Carbon-based materials have a wide range of properties, high electrical conductivity, and overall stability during cycling, making them suitable materials for batteries, including stationary and large-scale systems. This review summarizes the latest progress on materials based on elemental carbon for modern rechargeable electrochemical power sources, such as commonly used lead−acid and lithium-ion batteries. Use of carbon in promising technologies (lithium−sulfur, sodium-ion batteries, and supercapacitors) is also described. Carbon is a key element leading to more efficient energy storage in these power sources. The applications, modifications, possible bio-sources, and basic properties of carbon materials, as well as recent developme... [more]

To effectively mitigate global greenhouse gas emissions, both industrialized and developing countries should participate in the energy transition that to replace fossil fuels with renewable energy. Multilateral development banks (MDBs) have been scaling up their renewable energy finance to developing countries to help them achieve their renewable energy targets. This study examines the evolution of energy financing of the World Bank, the oldest and largest MDB, by reviewing and estimating its sector-specific energy investments made over the last 35 years (1985−2019). The results confirm that the World Bank is on the right track supporting energy transition in developing countries, overall; however, limitations exist. While the share of investments in non-hydro renewable energy (NHRE) in the World Bank’s total energy finance was expanded from 1% (1985−1990) to 16.5% (2011−2019), the share of fossil fuels contracted from 51.8% (1985−1990) to 15.2% (2011−2019). However, commitments to fos... [more]

A database for flowing condensation of three hydrocarbons, namely propane (R290), isobutane (R600a), and propylene (R1270), is extended by experimental tests in a smooth tube and two microfinned tubes with an increase of heat exchange area of 1.51 and 2.63, respectively. The outer diameter for all of the test tubes was 5 mm. Heat transfer coefficient and pressure drop are compared between the fluids and tubes. Tests were conducted at saturation temperatures of 35 °C and mass fluxes between 200 to 500 kgm−2s−1. Results show that isobutane (R600a) has a higher heat transfer coefficient and pressure drop while propylene (R1270) and propane (R290) present very similar characteristics. Both microfinned tubes increase the heat transfer coefficient compared to the smooth tube, but with different magnitude and tendencies and almost independently of the fluid tested. The maximum increase of heat transfer coefficient reached values of up to 1.8 while the maximum increase in pressure drop was by... [more]

Frost deposits on the outdoor heat exchanger of an air source heat pump (ASHP) air conditioner and reduces its capacity during winter operation. However, the prevailing reverse-cycle defrosting (RCD) turns the indoor heat exchanger into an evaporator and ceases heat supply to the living space. Consequently, the thermal comfort for indoor occupants is deteriorated. This article proposes a heater-assisted ASHP to tackle this problem. With an 800 W electromagnetic heater equipped upstream of the outdoor heat exchanger to provide refrigerant with additional heat, the ASHP retarded frost under original throttling control and compressor speed during the heating cycle (frostless mode), and even removed frost with uninterrupted heat supply to indoor space under little throttling and reduced compressor speed (anti-frost mode). Compared with the original operation of the ASHP when the heater was off (baseline mode), frostless and anti-frost modes extended heating duration by 17.9% and 99.7%, res... [more]

This paper presents a novel single-phase grid-tied neutral-point-clamped (NPC) five-level converter (SPFLC). Unlike the literature on five-level NPC topologies, the proposed one is capable of inherently balancing the voltage of the DC-link split capacitors. For this purpose, a simple Multicarrier Phase Disposition (MPD) Pulse Width Modulation (PWM) technique is used, thus avoiding both complex modifications to the Space Vector Modulation (SVM) and offset voltage injections into the carrier based (CB) PWM, as commonly done in most conventional balancing algorithms. Bearing in mind that the proposed balancing strategy only requires measuring the capacitors’ voltages and the sign of the converter output current, it has a very low complexity. The developed strategy is not only straightforwardly implemented but is also very effective for obtaining symmetrical and undistorted voltage levels from the proposed multilevel converter, as well as for significantly improving the power quality of th... [more]

In recent years, the need to reduce environmental impacts and increase flexibility in the energy sector has led to increased penetration of renewable energy sources and the shift from concentrated to decentralized generation. A fuel cell is an instrument that produces electricity by chemical reaction. Fuel cells are a promising technology for ultimate energy conversion and energy generation. We see that this system is integrated, where we find that the wind and photovoltaic energy system is complementary between them, because not all days are sunny, windy, or night, so we see that this system has higher reliability to provide continuous generation. At low load hours, PV and electrolysis units produce extra power. After being compressed, hydrogen is stored in tanks. The purpose of this study is to separate the Bahr AL-Najaf Area from the main power grid and make it an independent network by itself. The PEM fuel cells were analyzed and designed, and it were found that one layer is equal... [more]

The process of material removal from a workpiece to obtain the desired shape is termed machining. Present-day material removal technologies have high spindle speeds and thus allow quick material removal. These high-speed spindles are highly exposed to vibrations and, as a result, the accuracy of the final workpiece’s dimensions is compromised. To overcome this problem, the motion of the tool is restricted, and multiple degrees of freedom are given through the motion of the workpiece in different axes. A machining bed configured as a parallel manipulator capable of giving six degrees of freedom (DOF) to the workpiece is proposed in this regard. However, the proposed six DOF machining bed should be energy efficient to avoid an increase in machining cost. The benefit of using the proposed configuration is a reduction in dimensional error and computational time which, as a result, reduces the energy utilization, vibrations, and machining time in practice. This paper presents kinematics, dy... [more]

The reference literature contains data on the ideal gas-phase heat capacities and enthalpies of substances obtained experimentally. In this brief report, the highly accurate and simple unified analytical dependences of the heat capacity and enthalpy of normal alkanes larger than propane in the ideal gas state on temperature and the number of carbon atoms in a molecule are derived based on the analysis of the structure of chemical groups in the molecules and on the reference values of heat capacity and enthalpy for any two selected normal alkanes at one temperature. The dependences include a single set of coefficients for all normal alkanes and can be applied even to normal alkanes with the number of carbon atoms larger than 20, for which there is no data available. The dependences are thoroughly checked against two different sets of experimental data and two different sets of computational data obtained by low- and high-level theoretical methods: PM6 and G4. The error in calculating th... [more]

The objective of this paper is to identify the determinants of decarbonization processes in Poland by urban and rural areas. It also presents directions for knowledge diffusion on decarbonization to develop a sustainable energy strategy for Poland, particularly for local governments and cities. Despite extensive research on the determinants of decarbonization and sustainable energy development, there is a lack of specific solutions in this area. The authors of this paper investigated which determinants, according to the respondents, would lead to better decarbonization solutions in cities and villages in terms of sustainability. The studied sample was purposefully selected and an online questionnaire was used with the use of the “snowball” method. The authors conducted surveys that allowed the concerned parties themselves (respondents) to indicate which factors they believe best influence decarbonization. Such measures are helpful in terms of the understanding public acceptance of deca... [more]

This publication presents a multi-faceted analysis of the fuel consumption of motor vehicles and the way human impacts the environment, with a particular emphasis on the passenger cars. The adopted research methodology is based on the use of artificial neural networks in order to create a predictive model on the basis of which fuel consumption of motor vehicles can be determined. A database containing 1750 records, being a set of information on vehicles manufactured in last decade, was used in the process of training the artificial neural networks. The MLP (Multi-Layer Perceptron) 22-10-3 network has been selected from the created neural networks, which was further subjected to an analysis. In order to determine if the predicted values match the real values, the linear Pearson correlation coefficient r and coefficient of determination R2 were used. For the MLP 22-10-3 neural network, the calculated coefficient r was within range 0.93−0.95, while the coefficient of determination R2 assu... [more]

Climate change requires the reduction of energy consumption in transport and the associated fuel consumption, and emission of pollutants into the atmosphere. This issue is particularly relevant to air transport. Referring to the current legislative actions aimed at reducing the negative impact of air transport on the environment, the paper describes the possibilities of reducing energy consumption and related emissions. The Boeing 737 aircraft equipped with Snecma CFM 56C engines was adopted for the research. The research problem focused on determining a cruising trajectory characterized by the shortest cruising time and the lowest energy consumption by the aircraft during the flight between two selected European airports in given meteorological conditions. In the analysis, the Dijsktra’s algorithm was applied and built-in MATLAB functions were used. Based on the studied case, it was shown that it was possible to reduce both energy consumption and CO2 emissions by 10%. The novelty of t... [more]

Cities have been struggling for many years with many transport problems, including the impact of carbon monoxide emitted by vehicles on the environment, traffic jams, high energy consumption, numerous accidents or high infrastructure costs. There is also a dynamic growth of vehicles on the roads, which is why an increasing number of cities are introducing intelligent transportation systems (ITS), which is part of the concept of smart cities. This paper proposes a new matrix to assess the effects of the ITS implementation in the context of a concept Smart City, which consists of five criteria: (1) movement speed; (2) safety; (3) environmental; (4) economic; (5) satisfaction and amenities for society/passengers. In this new approach the benchmark values of the indicators assigned to the criteria are involved and, therefore, it is possible to determine the level of effectiveness of the ITS in public transport that uses low-carbon energy. This research used literature studies to establish... [more]

This study examined the feasibility of green hydrogen as a transport fuel for the very heavy vehicle (VHV) fleet in New Zealand. Green hydrogen is assumed to be produced through water electrolysis using purely renewable energy (RE) as an electricity source. This study chose very heavy vehicles as a potential market for green hydrogen, because it is considered “low-hanging fruit” for hydrogen fuel in a sector where battery electrification is less feasible. The study assumed a large-scale, decentralized, embedded (dedicated) grid-connected hydrogen system of production using polymer electrolytic membrane (PEM) electrolysers. The analysis comprised three steps. First, the hydrogen demand was calculated. Second, the additional RE requirement was determined and compared with consented, but unbuilt, capacity. Finally, the hydrogen production cost was calculated using the concept of levelized cost. Sensitivity analysis and cost reduction scenarios were also undertaken. The results indicate an... [more]

During the fast-filling of a high-pressure hydrogen tank, the temperature of hydrogen would rise significantly and may lead to failure of the tank. In addition, the temperature rise also reduces hydrogen density in the tank, which causes mass decrement into the tank. Therefore, it is of practical significance to study the temperature rise and the amount of charging of hydrogen for hydrogen safety. In this paper, the change of hydrogen temperature in the tank according to the pressure rise during the process of charging the high-pressure tank in the process of a 82-MPa hydrogen filling system, the final temperature, the amount of filling of hydrogen gas, and the change of pressure of hydrogen through the pressure reducing valve, and the performance of heat exchanger for cooling high-temperature hydrogen were analyzed by theoretical and numerical methods. When high-pressure filling began in the initial vacuum state, the condition was called the “First cycle”. When the high-pressure charg... [more]

Currently, Lithium-ion batteries (LiB) are widely applied in energy storage devices in smart grids and electric vehicles. The state of charge (SOC) is an indication of the available battery capacity, and is one of the most important factors that should be monitored to optimize LiB’s performance and improve its lifetime. However, because the SOC relies on many nonlinear factors, it is difficult to estimate accurately. This paper presented the design of an effective SOC estimation method for a LiB pack Battery Management System (BMS) based on Kalman Filter (KF) and Artificial Neural Network (ANN). First, considering the configuration and specifications of the BMS and LiB pack, an ANN was constructed for the SOC estimation, and then the ANN was trained and tested using the Google TensorFlow open-source library. An SOC estimation model based on the extended KF (EKF) and a Thevenin battery model was developed. Then, we proposed a combined mode EKF-ANN that integrates the estimation of the E... [more]

To meet the stated climate change targets and to ensure the capability of meeting the current and future energy demands, there is an urgent need to develop renewable energy sources, such as geothermal systems. If geothermal systems are to be cost-efficient and are to enjoy public confidence, it is essential that they are designed and installed in accordance with the prevailing site-specific conditions. A thorough understanding of the thermal behaviour of the surrounding ground is, therefore, critical. In this work, we investigated temperature and its evolution in the vicinity of a shallow geothermal helix-shaped borehole heat exchanger (BHE). To measure the temperature close to the actual geothermal system, an additional U-tube probe was installed at the edge of the same borehole. A thermal load was then applied to the BHE, and the temperature was detected in the nearby U-tube. The temperature measurements were made with a GEOSniff monitoring device. To understand these localised tempe... [more]

To meet rising energy demands, power plant operations will expand, influencing the interactions between the water−energy nexus and society. However, a major challenge is integration of social dimensions within electricity generation. To address this, we generate a baseline dataset using US public data (2014−2019) from the Energy Information Administration and US Bureau of Labor Statistics. We identify the rate of energy consumed, CO2, SO2 and NOx emissions generated, and water used per MWh net electricity as well as employee wellbeing per unit MW capacity during electricity generation. Rates of energy consumption (MMBtu/MWh) decreased 4.9%, but water consumption and withdrawal (m3/MWh) both increased 0.93% and 0.31%, respectively. Emissions of CO2, SO2 and NOx decreased 22.64%, 75% and 25% MT/MWh, respectively. Thermoelectric cooling withdrawal and consumption is led by natural gas (50.07%, 38.31%), coal (29.61%, 25.07%), and nuclear energies (13.55%, 18.99%). Electric power generation... [more]