In this work, an energetic and environmental evaluation of the electricity generation process through refuse-derived fuel (RDF) gasification coupled to a gas microturbine (GM) was performed. Two scenarios are considered with different gasification agents in RDF gasification modeling: air and air enriched with oxygen. A thermodynamic chemical equilibrium approach was used to analyze the gasification parameters. The results of RDF gasification indicate a maximum value of syngas low heating value (LHV) equal to 8.0 MJ/Nm3, obtained for an equivalence ratio of 0.3. The use of these syngas in the gas microturbine produces 79.6 kW of electrical power. For the environmental evaluation of gasification and electricity generation systems, the Life Cycle Assessment methodology was employed. The calculated environmental impacts indicate that the emission of contaminants from fossil fuel combustion (in the stage of transport by heavy load vehicles) and that the electricity consumption for equipment... [more]

High azoxystrobin (AZO), difenoconazole (DFZ), and imidacloprid (IMD) pesticide removal rates in sixteen bench-scale experiments concerning tomato washing water treatment were obtained through a UVC/H2O2 advanced oxidative process. Experimental conditions ([H2O2]0) and irradiance (EUVC) were optimized for higher degradation rates (pseudo-first-order reaction). To consider both economic aspects and environmental impacts when defining the treatment technology, as well as technological requirements, this study applied a multi-criteria decision-making method (MCDM) to assess and differentiate similar UVC/H2O2 process configurations. This allowed for the identification of the cheapest experimental arrangement with the lowest associated environmental impacts, coupled to the highest degradation rate (kIMD). After consulting experts to determine the importance of the applied criteria and measuring alternative performances, experiment E7 ([H2O2]0 = 43.5 mg L−1; EUVC = 15.0 W m−2; kIMD = 0.236 s... [more]

A considerable amount of food waste ends up in centralized treatment plants due to the lack of preventive measures, resulting in significant environmental impacts. Hospitality food waste management is even more resource-intensive because of animal by-products regulation. According to this regulation, companies must store and then consign waste to specific waste managers. The extensive need for transportation of high-moisture-content materials is the leading cause of the impact. Moreover, the management of category III animal by-products is costly for companies. A previous study has shown the economic benefits of decentralized animal by-product treatment by intensive composting in catering companies. Although the produced compost was characterized by exceptional quality parameters, it was phytotoxic. The investigation of hospitality waste management is scarcely discussed among scholars, and waste management on a regional scale is nearly absent. This study examines the regional managemen... [more]

In this work, the Life Cycle Assessment (LCA) methodology is used to examine the implications of CO2 capture from a natural gas combined cycle power plant with post-combustion carbon capture (NGCC-CCS) in Iraq, taking into account two different design scenarios. In the first scenario (retrofit), the carbon capture unit is considered as an end pipe technology that can be linked to an existing power plant. The second scenario considers a grassroots design, in which a new power plant equipped with a carbon capture unit needs to be constructed. The LCA is carried out based on different impact assessment (LCIA) methodologies of ReCipe 2016 Midpoint (H), TRACI 2.1, and IMPACT 2002+ to investigate whether the chosen LCIA method influences the LCA scenario analysis for decision support in process development. The results of three impact categories applied to both scenarios reveal a 28% reduction in Global Warming Potentials (GWPs) and a 14% and 17% increase in the Particulate Matter Formation... [more]

High energy consumption is one of the main problems of drying, a critical process for many industrial sectors. The optimization of drying energy use results in significant energy saving and has become a topic of interest in recent decades. We investigate benefits of heat recovery in a convective drying system by comparing two different scenarios. The Baseline Scenario is a conventional industrial dryer, and Scenario 1 includes the preheating of drying air by exhausts from the drying chamber. We show that the energy efficiency of the drying cycle is strictly related to the properties of the dried material and operative conditions, and performance improves significantly (by 59% to 87%) when installing a heat recovery unit (Scenario 1). Additionally, the temperature of drying air affects performance. We assess both scenarios by LCA analysis, measuring the environmental impacts and externalities of four different fuels (natural gas, light fuel oil, biomethane, and hardwood chips). Our find... [more]

Many studies have evaluated CO2 emission from batteries. However, the impact of Li-ion battery (LiB) degradation on the CO2 emissions from the material through operation phases has not been sufficiently examined. This study aims to clarify the dominant CO2 emission phase and the impact of the degradation of general industrial LiBs from repetitive cycle applications. We developed a model common to general LiB composition and calculated CO2 emissions by the LCA method using the IDEA database. Our model simplifies the degradation process, including capacity decrease and internal resistance increase. We used it in a sensitivity analysis of the carbon intensity of electricity charged to a LiB. The loss mechanism was determined by experimental data for an electric bus with an industrial LiB. The results illustrate that the carbon intensity of electricity affects CO2 emissions dominance, the operation phase for mix (71.3%), and the material phase for renewables (70.9%), and that battery degra... [more]

Net-zero climate districts are gaining wide attention at the European and international levels. Urban regeneration competitions have been launched recently to stimulate development; nevertheless, the literature does not yet provide a shared scope definition (i.e., product system). Using the process-based life cycle assessment method, the authors evaluate the climate profile of a new district in Milan (14 buildings with 36,000 m2 of gross surface area in total) aiming to become the first net-zero social housing project in Italy. The authors show in the results section how climate neutrality is achieved on the part of the real estate operator by varying the scope. The most conservative scenario (including all the emission sources considered in the analysis) indicates that the net-zero climate target is reached only by purchasing voluntary carbon credits. The authors also highlight: (i) a district composed of nearly-zero energy buildings is far from the definition of a net-zero climate em... [more]

There are different configurations selected by both industry and academia as the drivetrain for wind turbines in the power range of 10 to 16 MW. The choice of drivetrain system influences the levelized cost of energy, and, as the turbines become larger, and, therefore, costlier, there is more potential for the optimization of cost critical systems, like the drivetrain. The latter motivates the utilization of a life cycle assessment approach to profoundly influence the choice of drivetrain technology such that it offers a better compromise between the different aspects in the drivetrain life cycle. To this end, in this paper, various permanent magnet synchronous generator (PMSG)-based drivetrain technologies for 15 MW bottom-fixed and floating offshore wind turbine applications are designed and compared. The technologies under investigation are based on direct-drive, medium- and high-speed generators. The conceptual design of the drivetrain for the three technologies under consideration... [more]

The aim of this paper is to evaluate the overall life cycle environmental impact of an adiabatic compressed air energy storage (ACAES) system, which is designed to achieve the best match between the power production of a photovoltaic (PV) power plant and the power demand from the final user. The electrical energy demand of a small town, with a maximum power load of about 10 MW, is considered a case study. The ACAES system is designed with a compressor-rated power of about 10 MW and charging and discharging times of 10 and 24 h, respectively. Different sizes of the PV plant, ranging from 20 to 40 MWp, and two different solutions for the compressed air storage, an underground cavern, and a gas pipeline, are analyzed. The aim of this analysis is to compare the impacts on human health, ecosystem quality, climate change, and resource consumption of the PV power generation plant and the integrated PV-ACAES system with those of a reference scenario in which the end user demand is met entirely... [more]

The electric power industry is one of the major industries in terms of carbon dioxide (CO2) emissions, and it is necessary to explore low-carbon green power generation models. In recent years, more research has focused on the difference in carbon emissions in fossil energy versus renewable energy but ignored the impact of energy on human well-being. The life cycle assessment (LCA) method is a better method for assessing the impact of the low-carbon model on human well-being. In this paper, the carbon footprints of coal power plants and photovoltaic power (PV) plants generating 1 Kilowatt hour (kWh) of electricity are compared to analyze the degree of carbon emissions at different stages of the two models, and the environmental impact potential of the two models is analyzed using the LCA method. The differences between the two models in terms of human well-being were analyzed through questionnaires and quantified using the hierarchical analysis method. The impact of the different models... [more]

In Spain, most businesses are medium to small size enterprises, representing 90% of the total, but there is a lack of studies of the types of building this sector uses. The main objective of this paper is to present a method for the evaluation of small industrial construction projects to facilitate the introduction of eco-efficient solutions. For this, it is necessary to identify the most representative buildings and the aspects of these which have the most environmental impact. A methodology in place for the evaluation of dwelling construction is adapted, for the first time, to evaluate industrial buildings. The construction solutions characterized are those traditionally used in the sector, as identified through 87 surveys. A standardized classification of work units is proposed to enable the use of environmental product information, such as eco-labels and/or EPD, and LCA databases. The carbon footprint (CF) and water footprint (WF) are the indicators selected because of their straig... [more]

In the oil and gas industry, there has not been a consistent, concerted effort to reduce global greenhouse gas (GHG) emissions across the supply chain. In addressing this challenge, this study evaluates the potential GHG emissions reduction that may be realized through deployment of a geothermal power co-production system in two Colombian oil fields, compared to a base case where energy needs are derived through non-renewable sources such as gas and diesel. These geothermal power co-production systems make use of organic Rankine cycle (ORC) engines to convert the heat from produced oilfield fluids into electrical energy. The energy potential of this resource is evaluated through the exergy concept, and a life cycle analysis is implemented to calculate the carbon footprint using the Intergovernmental Panel on Climate Change (IPCC) 2013 methodology. In the two oil fields of interest, OFA and OFB, the results show a maximum potential energy production of 2260 kWe for OFA and 657 kWe for O... [more]

Expanding cities means increasing the need for energy in the residential sector. The supply of this energy must be in environmentally friendly ways; one method of meeting demand in the residential sector is the use of combined cooling, heating, and power (CCHP) systems. The current review paper shows that due to the high cost of gas and electricity, CCHP can be used in various sectors, such as hospitals and airports, to reduce energy consumption with lower environmental impacts by using renewable energy systems as the main driver. While CCHP systems are not feasible in tropical regions with high cooling demand, a solar hybrid system is a superior candidate for regions with sufficient radiation. CCHP can also be used in sectors such as wastewater treatment units, desalination systems, and hydrogen production units to improve performance and increase productivity. The carbon and water footprints of CCHP systems are discussed in detail. The main drivers for reducing carbon and water footp... [more]

In the context of climate change and the reduction in CO2 emissions from fossil fuel combustion, the integration of CO2 capture technologies in steam power plants is a key solution. The aim of this study was to analyze the use of ammonia, at different mass concentrations, in capturing post-combustion CO2 in a coal-fired power station and comparing it with the reference 30% MEA case. In this regard, a multi-criteria model was developed to establish the optimal solvent used, considering the least impact on technical performance, economic, and environmental indicators. As a result, the lowest CO2 capture cost was obtained for the CO2 capture process based on 7% NH3, with 59.07 €/tCO2. Integration of the CO2 capture process is more economically viable when the CO2 emissions tax is higher than 70 €/tCO2 for 7% NH3 and 15% NH3, 80 €/tCO2 for 5% NH3 and 30% MEA, and 90 €/tCO2 for 2% NH3. Regarding the overall efficiency, the energy penalty associated with the CO2 capture process integration v... [more]

At present, there are significant knowledge gaps in the research on the resource and environmental effects of rare earth exploitation, especially the carbon emission coefficient. This study applies the life cycle assessment approach to calculate the carbon footprint of producing mixed oxide rare earths using ionic rare earth resources and analyze the sources and influencing factors of the carbon footprint. The results show that the carbon footprint of producing 1 kg of mixed oxide rare earths using ionic rare earths is 17.8~24.3 kg CO2 eq, but its uncertainty is 15.54%; the total carbon footprint from 2012 to 2017 reaches 1.6 × 108~2.19 × 108 kg CO2 eq/year, and after 2018, the carbon footprint decreases to 1.51 × 108~2.07 × 108 kg CO2 eq /year. The total carbon footprint of illegal mining is around 1.50 × 108~1.59 × 108 kg CO2 eq/ year. In principle, the higher the recovery rate, the lower the carbon footprint of 1 kg REO production, but with the increase in the recovery rate, the car... [more]

Carbon-reinforced concrete (CRC) has the potential to play a pivotal role in optimizing the built environment and has therefore been experiencing a wave of research and development in the construction industry in recent years. The production of carbon fibers for CRC is energy-intensive, prompting the need to explore circular economy approaches (e.g., recycling at the End-of-Life (EoL)) to optimize the environmental performance of this material. Underdeveloped processes and a resulting lack of primary data regarding the recycling of CRC have hampered a comprehensive sustainability assessment of the novel composite building material. The novelty of this article is the detailed presentation of possible EoL scenarios for CRC and the detailed determination of the respective environmental impacts. This study aims to model EoL options within a Life Cycle Assessment (LCA), focusing on the EoL stage based on ISO 14040/44 using the GaBi ts 10.5.1.124 software and the CML2001 (2016) methodology.... [more]

The copper demand and production in China are the largest in the world. In order to obtain the trends of the energy consumption and GHG emissions of copper production in China over a number of years, this paper uses a life cycle analysis method to calculate the above two indexes, in the years between 2004 and 2017. The life cycle energy consumption ranged between 101.78 and 31.72 GJ/t copper and the GHG emissions varied between 9.96 and 3.09 t CO2 eq/t copper due to the improvements in mining and smelting technologies. This study also analyses the influence of electricity sources, auxiliary materials consumption, and copper ore grade on the life cycle performance. Using wind or nuclear electricity instead of mixed electricity can reduce energy consumption by 63.67−76.27% or 64.23−76.94%, and GHG emissions by 64.42−77.84% or 65.08−78.63%, respectively. The GHG emissions and energy consumption of underground mining are approximately 2.97−7.03 times that of strip mining, while the influen... [more]

This paper provides a brief review on wastewater treatment system and the application of life cycle assessment (LCA) for assessing its environmental performance. An extensive review regarding the geographical relevance of LCA for WWTPs, and the evaluation of sustainable wastewater treatment by LCA in both developed and developing countries are also discussed. The objective of the review is to identify knowledge gap, for the improvement of the LCA application and methodology to WWTPs. A total of 35 published articles related to wastewater treatment (WWT) and LCA from international scientific journals were studied thoroughly and summarised from 2006 to 2022. This review found that there is lack of studies concerning LCA of WWTPs that consider specific local criteria especially in the developing countries. Thus, it is important to: (1) assess the influence of seasonality (i.e., dry and wet seasons) on the environmental impact of WWT, (2) investigate environmental impacts from WWTPs in dev... [more]

The activated sludge process is the most widespread sewage treatment method. It typically consists of a pretreatment step, followed by a primary settling tank, an aerobic degradation process, and, finally, a secondary settling tank. The secondary effluent is then usually chlorinated and discharged to a water body. Tertiary treatment aims at improving the characteristics of the secondary effluent to facilitate its reuse. In this work, through a literature review of the most prominent tertiary treatment methods, a benchmarking of their technical efficiency, economic feasibility, and environmental impact was carried out. The photo-Fenton method proved to be the most technically efficient process, significantly reducing the microbial load and pharmaceutical content (by 4.9 log and 84%, respectively) of the secondary effluent. Chlorination and UV irradiation exhibited the lowest treatment costs (0.004 EUR/m−3) and the lowest global warming potential (0.04 and 0.09 kg CO2eq. m−3, respectivel... [more]

Aluminum production is a major energy consumer and important source of greenhouse gas (GHG) emissions globally. Estimation of the energy consumption and GHG emissions caused by aluminum production in China has attracted widespread attention because China produces more than half of the global aluminum. This paper conducted life cycle (LC) energy consumption and GHG emissions analysis of primary and recycled aluminum in China for the year 2020, considering the provincial differences on both the scale of self-generated electricity consumed in primary aluminum production and the generation source of grid electricity. Potentials for energy saving and GHG emissions reductions were also investigated. The results indicate that there are 157,207 MJ of primary fossil energy (PE) consumption and 15,947 kg CO2-eq of GHG emissions per ton of primary aluminum ingot production in China, with the LC GHG emissions as high as 1.5−3.5 times that of developed economies. The LC PE consumption and GHG emiss... [more]

The unsustainable take-make-dispose linear economy prevalent in healthcare contributes 4.4% to global Greenhouse Gas emissions. A popular but not yet widely-embraced solution is to remanufacture common single-use medical devices like electrophysiology catheters, significantly extending their lifetimes by enabling a circular life cycle. To support the adoption of catheter remanufacturing, we propose a comprehensive emission framework and carry out a holistic evaluation of virgin manufactured and remanufactured carbon emissions with Life Cycle Analysis (LCA). We followed ISO modelling standards and NHS reporting guidelines to ensure industry relevance. We conclude that remanufacturing may lead to a reduction of up to 60% per turn (−1.92 kg CO2eq, burden-free) and 57% per life (−1.87 kg CO2eq, burdened). Our extensive sensitivity analysis and industry-informed buy-back scheme simulation revealed long-term emission reductions of up to 48% per remanufactured catheter life (−1.73 kg CO2eq).... [more]

In this study, cradle-to-product life cycle analyses were conducted for a variety of natural-gas-based and coal-based SOFC power plant conceptual designs, while also accounting for long-term SOFC degradation. For each type of plant, four base case designs were considered: a standalone SOFC plant, a standalone SOFC plant with a steam cycle, an SOFC/GT hybrid plant, and an SOFC/GT hybrid plant with a steam cycle. The boundary of each base case was subsequently expanded to include either wet cooling or dry cooling options and DC to AC conversion, and was subjected to additional cradle-to-product life cycle analyses. The environmental impact results were computed using ReCiPe 2016 (H) and TRACI 2.1 V1.05 in SimaPro. The main factors affecting the midpoint impacts between cases were the plant efficiency and total SOFC manufacturing required over the plant’s lifetime, which were both strongly connected to long-term degradation effects. The findings also showed that the standalone SOFC plant... [more]

SimaPro model used in this work.

The co-cracking of vacuum gas oil (VGO) and bio-oil has been proposed to add renewable carbon into the co-processing products. However, the environmental performance of the co-processing scheme is still unclear. In this paper, the environmental impacts of the co-processing scheme are calculated by the end-point method Eco-indicator 99 based on the data from actual industrial operations and reports. Three scenarios, namely fast pyrolysis scenario, catalytic pyrolysis scenario and pure VGO scenario, for two cases with different FCC capacities and bio-oil co-processing ratios are proposed to present a comprehensive comparison on the environmental impacts of the co-processing scheme. In Case 1, the total environmental impact for the fast pyrolysis scenario is 1.14% less than that for the catalytic pyrolysis scenario while it is only 26.1% of the total impacts of the pure VGO scenario. In Case 2, the environmental impact of the fast pyrolysis scenario is 0.07% more than that of the catalyti... [more]

Carbon capture, transport, and storage (CCS) is an essential technology to mitigate global CO2 emissions from power and industry sectors. Despite the increasing recognition and interest in both the scientific community and stakeholders, current CCS deployment is far behind targeted ambitions. A key reason is that CCS is often perceived as too expensive to reduce CO2 emissions. The costs of CCS have however traditionally been looked at from the industrial plant point of view which does not necessarily reflect the end-user’s perspective. This paper addresses the incomplete view by investigating the impact of implementing CCS in industrial facilities on the overall costs and CO2 emissions of end-user products and services. As an example, this work examines the extent to which an increase in costs of raw materials (cement and steel) due to CCS impact the costs of building a bridge. Our results show that although CCS significantly increases the cost of cement and steel, the subsequent incre... [more]