This paper presents a method for supplying stable electricity using renewable energy sources and energy storage systems (ESSs) in a small-scale microgrid (MG) such as an island. Traditional control methods, such as master−slave control and droop control, have focused on equalizing power sharing among a small number of generators and do not deal well with emergencies such as unplanned generator failures. This paper proposes a control method that can stably maintain the frequency of the MG in various situations by combining the advantages of master−slave control and droop control and complementing the disadvantages. Simulations were performed under various conditions to verify the proposed control method.

The power sector plays a significant role in carbon neutrality strategies, and the grid system is a crucial part of the power sector. In particular, with less mitigation potential from technology efficiency, the credit from whole life cycles is critical. This paper describes the investigation of the environmental impacts of various scenarios from the perspective of life cycles. By using the life cycle assessment (LCA) method, various grid systems are examined as a case study, including a traditional, renewable energy, and power storage grid system, as well as a microgrid, in Guangdong. The results highlight the fact that with the systematic improvement of a grid, significant environmental benefits can be achieved. For a grid system, optimization through technology has significant carbon reduction effects even if the power grid structure is not changed. Using renewable energy instead of traditional fuel can reduce the emission of 0.05 kg of CO2-equivalent greenhouse gas per 1 kWh of ele... [more]

Vanadium nitride (VN) with a wide working window has been identified as a promising electrode material candidate for batteries due to the high specific capacitance and the excellent electrical conductivity. Here, we have successfully prepared VCN nanobelts, which display mesoporous structure with high specific surface area (54.4 m2 g−1) and the total pore volume was 0.266 cm3 g−1. Furthermore, the prepared flexible Zn-ion battery (FZIB) with VCN-5 not only exhibited high specific capacitance (81 μAh cm−2), excellent rate capability, and long cyclic durability (77% after 1000 cycles at 0.6 mA cm−2) but also had the characteristics of flexibility. This FZIB is important to reduce the difficulty in thermal management and can be used in a series of applications, including wearable electric devices.

As renewable energy sources, such as solar systems, are becoming more popular, the focus is moving into more effective utilization of these energy sources and harvesting more energy for intermittency reduction in this renewable source. This is opening up a market for methods of energy storage and increasing interest in batteries, as they are, as it stands, the foremost energy storage device available to suit a wide range of requirements. This interest has brought to light the downfalls of batteries and resultantly made room for the investigation of ultra-capacitors as a solution to these downfalls. One of these downfalls is related to the decrease in capacity, and temperamentality thereof, of a battery when not used precisely as stated by the supplier. The usable capacity is reliant on the complete discharge/charge cycles the battery can undergo before a 20% degradation in its specified capacity is observed. This article aims to investigate what causes this degradation, what aggravates... [more]

In this work, a commercial paraffin PCM (RT35) characterized by a change range of the solid-liquid phase transition temperature Ts−l=29−36 °C and the low thermal conductivity λSL=0.2 W/m K is experimentally tested by submitting it to thermal charging/discharging cycles. The paraffin is contained in a case with a rectangular base and heated from the top due to electrical resistance. The aim of this research is to show the benefits that a 95% porous copper metal foam (pore density PD=20PPI) can bring to a PCM-based thermal storage system by simply loading it, due to the consequent increase in the effective thermal conductivity of the medium (λLOAD=7.03 W/m K). The experimental results highlight the positive effects of the copper foam presence, such as the heat conduction improvement throughout the system, and a significant reduction in time for the complete melting of the PCM. In addition, the experimental data highlight that in the copper-foam-loaded PCM the maximum temperature reached... [more]

Climate change motivated by human activities constitutes one of the main challenges of this century. To cut carbon emissions in order to mitigate carbon’s dangerous effects, the current energy generation mix should be shifted to renewable sources. The main drawback of these technologies is their intermittency, which will require energy storage systems to be fully integrated into the generation mix, allowing them to be more controllable. In recent years, great progress to develop an effective and economically feasible energy storage systems, particularly motivated by the recent rise of demand for electric transportation, has been made. Lithium-ion (Li-ion) battery prices have fallen near 90% over the past decade, making possible the affordability of electric vehicles and transforming the economics of renewable energy. In this work, a study on storage capacity demand previously presented as conference paper is expanded, including a deep analysis of the Spanish generation mix, the evaluat... [more]

The work deals with a newly developed prototype of an electrical control unit (ECU) for a magnetorheological (MR) damper powered by energy harvested from vibrations. The ECU, consisting of a rectifying bridge, a driver unit, a microcontroller, and an internal power supply system, is an advanced version of the specially designed processing system for energy harvested from vibrations and the use of this energy to control the MR damper. Unlike a typical MR damper control system in which electrical circuits are powered from an external energy source, the ECU is powered by a part of the energy extracted from a vibrating system using an electromagnetic harvester. However, the excess amount of energy recovered over that necessary to power the MR damper and electrical circuits can be collected in harvested energy storage. The study presents the design concept of the ECU, computer simulations of the in-built driver unit (DU), the method of connecting the ECU with the harvester, the MR damper an... [more]

The penetration of renewable energy sources (RESs) in the electrical power system has increased significantly over the past years due to increasing global concern about climate change. However, integrating RESs into the power market is highly problematic. The output of RESs such as wind turbines (WTs) and photovoltaics (PVs) is highly uncertain. Their correlation with load demand is not always guaranteed, which compromises system reliability. Distributed energy resources (DERs), especially demand response (DR) programs and energy storage systems (ESSs), are possible options to overcome these operational challenges under the virtual power plant (VPP) setting. This study investigates the impact of using a DR program and battery energy storage system (BESS) on the VPP’s internal electricity market, and also cost-minimization analysis from a utility viewpoint. Three different constrained optimal power flow (OPF) problems are solved such as base case, DR case, and BESS case to determine tot... [more]

Due to failures or even the absence of an electricity grid, microgrid systems are becoming popular solutions for electrifying African rural communities. However, they are heavily stressed and complex to control due to their intermittency and demand growth. Demand side management (DSM) serves as an option to increase the level of flexibility on the demand side by scheduling users’ consumption patterns profiles in response to supply. This paper proposes a demand-side management strategy based on load shifting and peak clipping. The proposed approach was modelled in a MATLAB/Simulink R2021a environment and was optimized using the artificial neural network (ANN) algorithm. Simulations were carried out to test the model’s efficacy in a stand-alone PV-battery microgrid in East Africa. The proposed algorithm reduces the peak demand, smoothing the load profile to the desired level, and improves the system’s peak to average ratio (PAR). The presence of deferrable loads has been considered to br... [more]

The synchronous integration of numerous input and output loads is possible with multi-input (MI) and multi-output (MO) DC−DC converters. In this paper, the non-isolated DC−DC converter described, which has a high step-up capability and multiple ports for outputs and inputs for energy storage system (ESS) applications. The voltage level of the converter is changeable. The capacity to provide the large voltage increases with a low duty cycle portion, the ease with which each duty cycle can be controlled, and minimal power losses are all advantages of the proposed design. The proposed system offers advantages for applications requiring energy storage. In the continuous conduction mode (CCM), the operation principles, steady-state evaluation, and extracting of the voltage and current coefficients are performed. The supply sources can be inserted or withdrawn without causing a cross-regulation issue in the proposed converter. Ultimately, the functionality of the proposed structure is examin... [more]

The resistance−capacitance (RC) model is one of the most applicable circuits for modeling the charging and discharging processes of supercapacitors (SCs). Although this circuit is usually used in the electric and thermal investigation of the performance of SCs, it does not include leakage currents. This paper presents exact analytical formulas of leakage-current-based supercapacitor models that can be used in industrial applications, i.e., constant-power-based applications. In the proposed model, current and voltage are represented as a solution of nonlinear equations that are solved using the standard Newton method. The proposed expressions’ accuracy is compared with the results obtained using traditional numerical integration methods with leakage current formulation and other methods, found in the literature, with no leakage current formulation. The results confirm that including leakage current represents a more accurate and realistic manner of modeling SCs. The results show that th... [more]

The cryogenic carbon capture (CCC) process is a promising post-combustion CO2 removal method. This method is very novel compared with conventional and well-developed methods. However, cryogenic carbon capture is not yet commercially available despite its techno-economic benefits. Thus, a model-based design approach for this process can provide valuable information. This paper will first introduce the cryogenic carbon capture process. Then, a comprehensive literature overview that focuses on different methods for modeling the process at the component level will be given. The modelling methods which are deemed most effective are presented more in depth for each of the key system components. These methods are compared with each other in terms of complexity and accuracy and the simplest methods with an acceptable level of precision for modelling a specific component in the CCC process are recommended. Furthermore, potential research areas in modeling and simulation of the CCC process are a... [more]

In the future, there will be more and more abandoned oil-gas wells with the exploitation of onshore oilfield resources. However, the large height difference in abandoned oil-gas wells can be used as building blocks for gravity power generation, thus maximizing the economic value of abandoned oil-gas wells. In this study, a scheme of gravity power generation by virtue of the spud-in casing depth of oil-gas wells is proposed, and a gravity power generation model based on abandoned oil-gas wells is established. The parameters and economic benefits of gravity energy storage are calculated for oil-gas wells in the Huabei oilfield, the Daqing oilfield, and the Xinjiang oilfield. It is shown that the power density and discharge time of the gravity energy storage system in abandoned oil-gas wells are suitable for distributed power generation. In addition, the fast response characteristics of energy storage in abandoned oil-gas wells are verified, which makes the system suitable for correcting... [more]

An energy storage system based on a Proton Exchange Membrane (PEM) electrolyzer system, which could be managed by a nanoGrid for Home Applications (nGfHA), is able to convert the surplus of electric energy produced by renewable sources into hydrogen, which can be stored in pressurized tanks. The PEM electrolyzer system must be able to operate at variable feeding power for converting all the surplus of renewable electric energy into hydrogen in reasonable time. In this article, the dynamic electric simulation model of a PEM electrolyzer system with its pressurized hydrogen tanks is developed in a proper calculation environment. Through the calculation code, the stack voltage and current peaks to a supply power variation from the minimum value (about 56 W) to the maximum value (about 440 W) are controlled and zeroed to preserve the stack, the best range of the operating stack current is evaluated, and hydrogen production is monitored.

Bidirectional DC/DC converters are widely adopted in new energy power generation systems. Because of the low conversion efficiency and non-isolation for conventional, bidirectional DC/DC converters in the photovoltaic energy storage complementary system, this paper proposes a bidirectional isolation LLC converter topology, with compensating inductance for the energy storage system; it has excellent characteristics, such as wide input voltage range and soft switching in full-load range. First, an AC equivalent model based on the fundamental wave equivalent method is established to derive the voltage gain. Meanwhile, a small signal model is also built to design a reasonably closed-looped controller. Finally, the improved bidirectional LLC resonant converter is applied to the photovoltaic energy storage complementary system. The correctness and feasibility for the bidirectional LLC converter topology under the proposed charging and discharging control strategy of the DC bus are verified b... [more]

Thermo-mechanical energy storage can be a cost-effective solution to provide flexibility and balance highly renewable energy systems. Here, we present a concise review of emerging thermo-mechanical energy storage solutions focusing on their commercial development. Under a unified framework, we review technologies that have proven to work conceptually through project demonstration at a scale above 1 MW by describing the current state of commercial development, quantifying techno-economic parameters, outlining the challenges, and assessing each technology’s potential for commercial viability. The levelized cost of storage for thermo-mechanical energy storage at storage duration between 8 h and 1 week is cheaper than that of lithium-ion batteries and hydrogen storage; however, energy storage for such duration does not pay for itself at the current renewable penetration levels. For medium-term energy storage to be viable, at the realistic storage cost of 15 USD/kWh to 40 USD/kWh, the inves... [more]

This paper aims to analyse two energy storage methods—batteries and hydrogen storage technologies—that in some cases are treated as complementary technologies, but in other ones they are considered opposed technologies. A detailed technical description of each technology will allow to understand the evolution of batteries and hydrogen storage technologies: batteries looking for higher energy capacity and lower maintenance, while hydrogen storage technologies pursuing better volumetric and gravimetric densities. Additionally, as energy storage systems, a mathematical model is required to know the state of charge of the system. For this purpose, a mathematical model is proposed for conventional batteries, for compressed hydrogen tanks, for liquid hydrogen storage and for metal hydride tanks, which makes it possible to integrate energy storage systems into management strategies that aim to solve the energy balance in plants based on hybrid energy storage systems. From the technical point... [more]

Increased renewable energy production and storage is a key pillar of net-zero emission. The expected growth in the exploitation of offshore renewable energy sources, e.g., wind, provides an opportunity for decarbonising offshore assets and mitigating anthropogenic climate change, which requires developing and using efficient and reliable energy storage solutions offshore. The present work reviews energy storage systems with a potential for offshore environments and discusses the opportunities for their deployment. The capabilities of the storage solutions are examined and mapped based on the available literature. Selected technologies with the largest potential for offshore deployment are thoroughly analysed. A landscape of technologies for both short- and long-term storage is presented as an opportunity to repurpose offshore assets that are difficult to decarbonise.

A plethora of multi-functional materials with properties that can be adjusted and tuned to meet the needs of energy storage and conversion has emerged over the last years [...]

As wearable electronic devices are becoming an integral part of modern life, there is a vast demand for safe and efficient energy storage devices to power them. While the research and development of microbatteries and supercapacitors (SCs) have significantly progressed, the latter has attracted much attention due to their excellent power density, longevity, and safety. Furthermore, SCs with a 1D fiber shape are preferred because of their ease of integration into today’s smart garments and other wearable devices. Fiber supercapacitors based on carbon nanotubes (CNT) are promising candidates with a unique 1D structure, high electrical and thermal conductivity, outstanding flexibility, excellent mechanical strength, and low gravimetric density. This review aims to serve as a comprehensive publication presenting the fundamentals and recent developments on CNT-fiber-based SCs. The first section gives a general overview of the supercapacitor types based on the charge storage mechanisms and e... [more]

Slovenia is a Central European country with a long history of hydropower. This paper gives a brief introduction to the current status of hydropower utilization and informs about some selected successful examples of hydropower plant operation. One such example is fish passage and flood risk reduction on the lower reaches of the Sava River at the Brežice hydroelectric power plant, taking into account a complex of morphological, hydrological, hydraulic, and anthropogenic factors. Future development is considered against the background of the National Energy and Climate Plan, which does not envisage any significant expansion in the capacity or function of the hydropower sector. The envisaged capacity increase is from the current 4430 GWh to around 4580 GWh by 2030. It is shown that the current energy storage capacity of Slovenia’s only pumped storage plant will be sufficient to offset the introduction of new non-dispatchable renewable energy sources by 2030. By around 2028, the country wil... [more]

Moving towards clean energy generation seems essential. To do so, renewable energy penetration is growing in the power systems. Although energy sources such as wind and solar are clean, they are not available consistently. Using energy storage will help to tackle variability. Liquid air energy storage is gaining attention among different energy storage technologies, as it is a promising option for grid-scale energy storage. This paper presents a detailed mixed integer linear model of liquid air energy storage to be used in scheduling and planning problems. A comprehensive cycle diagram of different processes of liquid air energy storage is presented, and a model has been developed accordingly. Simulations of the proposed model are carried out for the power system of Tenerife island and compared with the basic models. Basic models overlook specific characteristics of liquid air energy storage systems, such as charging and discharging start energy. Results confirm that the use of simple... [more]

The energy storage is an important character for sustainable energy structures and the prospective future economy. This paper aims to propose a multi-attribute decision analysis (MADA) approach to prioritize and choose the energy storage system (ESS) alternatives in terms of the different technical, economic, environmental and social aspects of them. In this line, an integrated approach is developed with the combination of intuitionistic fuzzy sets (IFSs), a method using the removal effects of criteria (MEREC), rank sum (RS) and the measurement of the alternatives and ranking based on compromise solution (MARCOS) methods for prioritizing the ESSs. The IF-MEREC-RS was used to find the integrated weight by combining the objective and subjective weights of the different indicators for prioritizing the ESSs. The MARCOS method was implemented to rank the various ESSs over several crucial indicators of sustainability. The practical outcome illustrates that the Li-ion battery (LIB) is the bes... [more]

Electrical energy storage systems have a fundamental role in the energy transition process supporting the penetration of renewable energy sources into the energy mix. Compressed air energy storage (CAES) is a promising energy storage technology, mainly proposed for large-scale applications, that uses compressed air as an energy vector. Although the first document in literature on CAES appeared in 1976 and the first commercial plant was installed in 1978, this technology started to gain attention only in the decade 2000−2010, with remarkable scientific production output and the realization of other pre-commercial demonstrators and commercial plants. This study applies bibliometric techniques to draw a picture of the current status of the scientific progress and analyze the trend of the research on CAES and identify research gaps that can support researchers and manufacturers involved in this entering technology. Recent trends of research include aspects related to the off-design, the de... [more]

To manage the imbalance between energy supply and demand in various energy systems such as energy storage and energy conversion, “phase change materials” are presented as promising options for these applications. To overcome the long-standing disadvantages of PCMs, for instance, small values of thermal conductivity, liquid leakage, separation of phase, and the problem of supercooling, advanced phase change composites (PCCs) manufactured by chemical modifications or the incorporation of functional additives are essential to overcome these disadvantages and promote the large-scale application of PCMs. Herein, we discuss a complete assessment of the recent development and crucial topics concerning PCCs, with a brief description of PCC preparation using different techniques, enhancing PCCs thermal conductivity approaches, and their applications. The various techniques of elaboration of PCCs used can be illustrated as polymerization, encapsulation, and hybrid confinement. Phase change mater... [more]