The present study proposes a complete 3D integrated model to simulate the top-blown supersonic coherent jet decarburization in the electric arc furnace (EAF) refining process. The 3D integrated model avoids the direct simulation of the supersonic coherent jet interacting with the liquid steel bath and provides a feasible way to simulate the decarburization in the liquid steel-oxygen two-phase reacting flow system with acceptable computational time. The model can be used to dynamically predict the details of the molten bath, including 3D distribution of in-bath substances, flow characteristics and bath temperature and provide a basis for optimizing the decarburization rate or other required parameters during the refining process.

The movement of water in the oceans generates a vast store of kinetic energy, which has led to the development of a wide variety of offshore energy harvesters all over the world. In our energy harvester, we used ionic polymer-metal composites (IPMCs) to convert the ocean energy into electricity. This paper presents a simulated model of an IPMC-based electrochemical kinetic energy harvesting system installed in the ocean and produced using the computational fluid dynamics (CFD) method. The simulation processes focused on the movement and structural stability of the system design in the ocean for the protection of the IPMC module against possible damage, which would directly affect the power output. Furthermore, the experimental tests under real marine conditions were also studied to analyze the electrical harvesting performance of the IPMC system. These results showed that the use of IPMC materials has many advantages as they are soft and durable; as a result, they can respond faster to... [more]

This paper focuses on the numerical modeling of the effect of the height of a combustion chamber on the development of a reference calorimeter whose objective is to measure the calorific value of natural gas. The impacts of temperature, velocity, and mass fraction on the exhaust gases were evaluated by varying the height of the combustion chamber. The eddy dissipation concept (EDC) approach was used to model combustion with two different chemical kinetic mechanisms: one with three steps, called the three-step mechanism defined by default in the software used, and second skeletal model, which consists of 41 steps, through the ChemKin-import file with 16 species. The main result of this study is the selection of a combustion chamber height for the reference calorimeter that produces the best performance in the combustion process, which is 70 mm, as well as the main differences in using a three-step mechanism and a skeletal model to simulate an oxy-fuel combustion reaction.

Buoyancy-driven airflow that included two isothermal inner plates established in a vented cavity is investigated numerically. The thermally optimum wall-to-wall spacing of the immersed channel, as well as its dependence with respect to the relevant governing parameters, are determined. Results are presented as a function of the aspect ratio b/H for a wide range of Rayleigh numbers RaH. A logarithmic correlation for the optimum (b/H)opt as a function of RaH is presented. In addition, since the outlined configuration might be subject to intense heating conditions, the influence of considering variable thermophysical properties is also included in the analysis. In fact, an appreciable influence of the variation of properties on (b/H)opt is also detected for a representative value of RaH = 109. Obtained results can be directly applied to the optimization of electronic equipment cooling, or even to thermal passive devices in buildings.

Coastal waves are an abundant nonpolluting and renewable energy source. A wave energy converter (WEC) must be designed for efficient and steady operation in highly energetic ocean environments. A direct-drive wave energy conversion (D-DWEC) system with a tubular permanent magnet linear generator (TPMLG) on a wind and solar photovoltaic complementary energy generation platform is proposed to improve the conversion efficiency and reduce the complexity and device volume of WECs. The operating principle of D-DWECs is introduced, and detailed analyses of the proposed D-DWEC’s floater system, wave force characteristics, and conversion efficiency conducted using computational fluid dynamics are presented. A TPMLG with an asymmetric slot structure is designed to increase the output electric power, and detailed analyses of the magnetic field distribution, detent force characteristics, and no-load and load performances conducted using finite element analysis are discussed. The TPMLG with an asym... [more]

Computational methods have become reliable tools in many disciplines for research and industrial design. There are, however, an ever-increasing number of details waiting to be included in the models and software, including, e.g., chemical reactions and many physical phenomena, such as particle and droplet behavior and their interactions. The dominant method for copper production, flash smelting, has been extensively investigated, but the settler part of the furnace containing molten high temperature melts termed slag and matte, still lacks a computational modeling tool. In this paper, two commercial modeling software programs have been used for simulating slag−matte interactions in the settler, the target being first to develop a robust computational fluid dynamics (CFD) model and, second, to apply a new approach for molten droplet behavior in a continuum. The latter is based on CFD coupled with the discrete element method (DEM), which was originally developed for modeling solid partic... [more]

This study proposed a kind of optimization design for a reversible axial-flow pump based on an ordinary one-way pump. Three-dimensional (3D) Reynolds-averaged Navier−Stokes (RANS) equations was used to predict the pump performance, and the optimized design was validated by an external characteristic test. Six main geometry parameters of an impeller and diffuser based on an orthogonal experiment were set as design variables. The efficiency and head under forward and reverse design conditions were set as the optimization objective. Based on 120 groups of sample designs obtained from Latin hypercube sampling (LHS), a two-layer artificial neural network (ANN) was used to build a non-linear function with high accuracy between the design variables and optimization objective. The optimized design was obtained from 300 groups of Pareto-optimal solutions using the non-dominated based genetic algorithm (NSGA) for multiobjective optimization. After optimization, there was a slight decrease in the... [more]

Slug flow is a multiphase flow pattern characterized by the occurrence of long gas bubbles (Taylor bubbles) separated by liquid slugs. This multiphase flow regime is present in many and diversified natural and industrial processes, at macro and microscales, such as in eruption of volcanic magmas, oil recovery from pre-salt regions, micro heat exchangers, and small-sized refrigerating systems. Previous studies in the literature have been mostly focused on tubular gas bubbles flowing in Newtonian liquids. In this work, results from several numerical simulations of tubular gas bubbles flowing in a shear thinning liquid in microchannels are reported. To simulate the shear thinning behavior, carboxymethylcellulose (CMC) solutions with different concentrations were considered. The results are compared with data from bubbles flowing in Newtonian liquids in identical geometric and dynamic conditions. The numerical work was carried out in computational fluid dynamics (CFD) package Ansys Fluent... [more]

Gas−solid cyclone separators are widely utilized in many industrial applications and usually involve complex multi-physics of gas−solid flow and heat transfer. In recent years, there has been a progressive interest in the application of computational fluid dynamics (CFD) to understand the gas−solid flow behavior of cyclones and predict their performance. In this paper, a review of the existing CFD studies of cyclone separators, operating in a wide range of solids loadings and at ambient and elevated temperatures, is presented. In the first part, a brief background on the important performance parameters of cyclones, namely pressure drop and separation efficiency, as well as how they are affected by the solids loading and operating temperature, is described. This is followed by a summary of the existing CFD simulation studies of cyclones at ambient temperature, with an emphasis on the high mass loading of particles, and at elevated temperatures. The capabilities as well as the challenge... [more]

An advanced algorithm has been developed in order to analyze the performance of re-boiling process of crude oil flowing inside reboilers tubes. The proposed model is composed from Heptane fire heater and a tube array. The heat flux produced from burner is transferred to the crude oil flowing inside the tube. The computational model is composed of two phases—Simulation of fire by using Fire Dynamics Simulator software (FDS) version 5.0 and then a nucleate boiling computation of the crude oil. FDS code is formulated based on CFD (Computational Fluid Dynamics) of fire heater. The thermo-physical properties (such as: thermal conductivity, heat capacity, surface tension, viscosity) of the crude oil were estimated by using empirical correlations. The thermal heat transfer to evaporating two-phase crude oil mixture occur by bubble generation at the wall (nucleate boiling) has been calculated by using Chen correlation. It has been assumed that the overall convective heat transfer coefficient i... [more]

High rate activated sludge (HRAS) processes have a high potential for carbon and energy recovery from sewage, yet they suffer frequently from poor settleability due to flocculation issues. The process of flocculation is generally optimized using jar tests. However, detailed jar hydrodynamics are often unknown, and average quantities are used, which can significantly differ from the local conditions. The presented work combined experimental and numerical data to investigate the impact of local hydrodynamics on HRAS flocculation for two different jar test configurations (i.e., radial vs. axial impellers at different impeller velocities) and compared the hydrodynamics in these jar tests to those in a representative section of a full scale reactor using computational fluid dynamics (CFD). The analysis showed that the flocculation performance was highly influenced by the impeller type and its speed. The axial impeller appeared to be more appropriate for floc formation over a range of impell... [more]

Renewed interest in freeze desalination has emerged due to its advantages over other desalination technologies. A major advantage of the freeze desalination process over evaporative methods is its lower energy consumption (latent heat of freezing is 333.5 kJ/kg and latent heat of evaporation is 2256.7 kJ/kg). Cryogenic fluids like LN2/LAir are emerging as an effective energy storage medium to maximise utilisation of intermittent renewable energy sources. The recovery of this stored cold energy has the potential to be used for freeze desalination. Computational Fluid Dynamics (CFD) modelling was developed to simulate the evaporation of liquid nitrogen to simultaneously conduct freeze desalination to investigate the feasibility of using cryogenic energy for freeze desalination. This integrated CFD model was validated using experimental heat exchanger test facility constructed, to evaporate liquid nitrogen to supply the cooling required for freezing. Parametric study on the LN2 flow rate... [more]

The unsteady flow process of waterjet pumps is related to the comprehensive performance and phenomenon of rotating stall and cavitation. To analyze the unsteady flow process on the unsteady condition, a computational domain containing nozzle, impeller, outlet guide vane (OGV), and shaft is established. The surface vortex of the blade is unstable at the valley point of the hydraulic unstable zone. The vortex core and morphological characteristics of the vortex will change in a small range with time. The flow of the best efficiency point and the start point of the hydraulic unstable zone on each turbo surface is relatively stable. At the valley point of the hydraulic unstable zone, the flow and pressure fields are unstable, which causes the flow on each turbo surface to change with time. The hydraulic performance parameters are measured by establishing the double cycle test loop of a waterjet propulsion device compared with numerical simulated data. The verification results show that the... [more]

The secondary settling tank is an essential unit for the biochemical treatment of domestic sewage, and its operational effect influences the quality of effluent. Under the influence of the confluence of rainwater and sewage, wastewater use habits, etc., the inflow of the secondary sedimentation tank changes over time. In this paper, OpenFOAM, an open-source computational fluid dynamics package, was used to study the dynamic behaviors of solid−liquid two-phase flow in the tank under influent flow rate variations. A coupled method including a mixture model, drift equation and a dynamic boundary method is proposed. Numerical investigations were carried out for a 2D axisymmetric sedimentation tank using 12 cases. With increasing influent flow rate, sludge accumulates continuously in the bottom left side of the tank, sludge hopper, and inlet; the sludge blanket thickness near the right end of the tank increases continuously; and the sludge concentration in the tank approximately linearly in... [more]

Computational Fluid Dynamics (CFD) has been firmly established as a fundamental discipline to advancing research on energy engineering. The major progresses achieved during the last two decades both on software modelling capabilities and hardware computing power have resulted in considerable and widespread CFD interest among scientist and engineers. Numerical modelling and simulation developments are increasingly contributing to the current state of the art in many energy engineering aspects, such as power generation, combustion, wind energy, concentrated solar power, hydro power, gas and steam turbines, fuel cells, and many others. This review intends to provide an overview of the CFD applications in energy and thermal engineering, as a presentation and background for the Special Issue “CFD Applications in Energy Engineering Research and Simulation” published by Processes in 2020. A brief introduction to the most significant reviews that have been published on the particular topics is... [more]

An internal circulation (IC) anaerobic reactor is widely used in the treatment of municipal and industrial wastewater with high volumetric loading rates. The performance of an IC reactor is closely related with hydrodynamic behaviors of anaerobic granules. Typically, anaerobic granules work in swarms and the settling behavior of a granule is disturbed by other granules. However, the research on anaerobic granule swarms is insufficient. In this work, Computational Fluid Dynamics (CFD) method was employed to study the hydrodynamic behaviors of anaerobic granule swarms with various voidages. The simulated results showed that the average velocity inside granules increased significantly as the voidage of granule swarm decreased and as the Reynolds number increased. The maximum shear stress on the granule’s surface increased with decreasing voidage and increasing Reynolds number. Based on the hydrodynamic behaviors of anaerobic granule swarms, an improved model of drag force coefficient for... [more]

In recent years and with the increasing rigor of the International Maritime Organization (IMO) emission regulations, the shipping industry has focused more on environment-friendly and efficient power. Low-pressure dual-fuel (LP-DF) engine technology with high efficiency and good emissions has become a promising solution in the development of marine engines. This engine often uses pre-combustion chamber (PCC) to ignite natural gas due to its higher ignition energy. In this paper, a parametric study of the LP-DF engine was proceeded to investigate the design scheme of the PCC. The effect of PCC parameters on engine performance and emissions were studied from two aspects: PCC nozzle diameter and PCC nozzle angle. The results showed that the PCC nozzle diameter affected the propagation of the flame in the combustion chamber. Moreover, suitable PCC nozzle diameters helped to improve flame propagation stability and engine performance and reduce emissions. Furthermore, the angle of the PCC no... [more]

A computational fluid dynamics (CFD) analysis of air distribution in a representative railway vehicle equipped with a heating, ventilation, air conditioning (HVAC) system is presented in this paper. Air distribution in the passenger’s compartment is a very important factor to regulate temperature and air velocity in order to achieve thermal comfort. A complete CFD model, including the car’s geometry in detail, the passengers, the luminaires, and other the important features related to the HVAC system (air supply inlets, exhaust outlets, convectors, etc.) are developed to investigate eight different typical scenarios for Northern Europe climate conditions. The results, analyzed and discussed in terms of temperature and velocity fields in different sections of the tram, and also in terms of volumetric parameters representative of the whole tram volume, show an adequate behavior from the passengers’ comfort point of view, especially for summer climate conditions.

In order to simulate the energy efficiency fluctuation behavior of an industrial centrifugal pump with a six-blade impeller, a full-scale three-dimensional (3D) an unsteady state computational fluid dynamics (CFD) model was used. Five operational points with different flow fluxes were numerically investigated by using the Navier⁻Stokes code with shear-stress transport (SST) k-ω turbulence model. The predicted performance curves agreed well with the test data. A sine function was fitted to the transient calculation results and the results show that the efficiency fluctuates mainly on the blade passing frequency, while the fluctuation level varies with flow rate. Furthermore, high efficiency is not necessarily associated with low fluctuation level. The efficiency fluctuation level is high at part-load points, and becomes relatively low when flow rate exceeds the design value. The effect of change in torque is greater than that of the head lift with respect to fluctuations of efficiency.... [more]

The injection flow rates of two liquid phases play a decisive role in the slug generation of the liquid-liquid slug flow. However, most injection flow rates so far have been constant. In order to investigate the effects of dynamic injection flow rates on the slug generation, including the slug size, separation distance and slug generation cycle time, a transient numerical model of a cross-junction square microchannel is established. The Volume of Fluid method is adopted to simulate the interface between two phases, i.e., butanol and water. The model is validated by experiments at a constant injection flow rate. Three different types of dynamic injection flow rates are applied for butanol, which are triangle, rectangular and sine wave flow rates. The dynamic injection flow rate cycles, which are related to the constant slug generation cycle time t0, are investigated. Results show that when the cycle of the disperse phase flow rate is larger than t0, the slug generation changes periodica... [more]

Rotating packed bed (RPB) has been demonstrated as a significant and emerging technology to be applied in natural gas desulfurization. However, droplet characteristics and principle in H2S selective absorption with N-methyldiethanolamine (MDEA) solution have seldom been fully investigated by experimental method. Therefore, a 3D Eulerian−Lagrangian approach has been established to investigate the droplet characteristics. The discrete phase model (DPM) is implemented to track the behavior of droplets, meanwhile the collision model and breakup model are employed to describe the coalescence and breakup of droplets. The simulation results indicate that rotating speed and radial position have a dominant impact on droplet velocity, average residence time and average diameter rather than initial droplet velocity. A short residence time of 0.039−0.085 s is credited in this study for faster mass transfer and reaction rate in RPB. The average droplet diameter decreases when the initial droplet ve... [more]

Limiting global temperature rise to well below 2 °C according to the Paris climate accord will require accelerated development, scale-up, and commercialization of innovative and environmentally friendly reactor concepts. Simulation-based design can play a central role in achieving this goal by decreasing the number of costly and time-consuming experimental scale-up steps. To illustrate this approach, a multiscale computational fluid dynamics (CFD) approach was utilized in this study to simulate a novel internally circulating fluidized bed reactor (ICR) for power production with integrated CO2 capture on an industrial scale. These simulations were made computationally feasible by using closures in a filtered two-fluid model (fTFM) to model the effects of important subgrid multiphase structures. The CFD simulations provided valuable insight regarding ICR behavior, predicting that CO2 capture efficiencies and purities above 95% can be achieved, and proposing a reasonable reactor size. The... [more]

The oscillating flow field of the double nozzle flapper servo valve pre-stage is numerically analyzed through Large Eddy Simulation (LES) turbulent modeling with the previous grid independence verification. The vortex street flow phenomenon can be observed when the flow passes through the nozzle flapper channel, the vortex alternating in each side produces the periodical flow oscillation. The structural and flow parameter effects on the oscillating flow are emphasized, and it could be determined that the pressure on the flapper is nearly proportional to the flow velocity and inversely proportional to the actual distance between the flapper and the nozzle. On the other hand, the main frequency of oscillation decreases with the velocity and increases with the distance between the nozzle flapper. The main stage movement is further considered with a User Defined Function (UDF), and it could be determined that the influences of the structural and flow parameters on the flow oscillation are... [more]

Anaerobic digestion (AD) is an established process for integrating waste management with renewable energy and nutrient recovery. Much of the research in this field focuses on the utilisation of new substrates, yet their effects on operational aspects such as fluid behaviour and power requirement for mixing are commonly overlooked, despite their importance for process optimisation. This study analysed rheological characteristics of samples from 21 laboratory-scale continuous stirred-tank biogas reactors (CSTBRs) digesting a range of substrates, in order to evaluate substrate effect on mixing efficiency and power demand through computational fluid dynamics (CFD). The results show that substrate and process parameters, such as solids content and organic loading, all have a significant effect on CSTBR fluid rheology. The correlation levels between rheological and process parameters were different across substrates, while no specific fluid behaviour patterns could be associated with substra... [more]

Stirred bioreactors are commonly used unit operations in the pharmaceutical industry. In this study, computational fluid dynamics (CFD) was used in order to analyze the influence of the impeller configuration (Segment−Segment and Segment−Rushton impeller configurations) and the impeller rotational speed (an operational parameter) on the hydrodynamic behaviour and mixing performance of a bioreactor equipped with a double impeller. A relatively close agreement between the power values obtained from the CFD model and those measured experimentally was observed. Various parameters such as velocity profiles, stress generated by impellers due to the turbulence and velocity gradient, flow number, and mixing time were used to compare the CFD simulations. It was observed that the impeller’s RPM could change the intensity of the interaction between the impellers when a Segment−Rushton impeller was used. In general, increasing the RPM led to an increase in total power and the stress acting on the... [more]