The objective of this review is to provide a deep overview of liquid biofuels produced from sugarcane bagasse and to address the economic challenges of an ethanol and acetone-butanol-ethanol blend in commercial processes. The chemistry of sugarcane bagasse is presented. Pretreatment technologies such as physical, chemical pretreatment, biological, and combination pretreatments used in the fermentation process are also provided and summarised. Different types of anaerobic bacteria Clostridia (yeast) are discussed to identify the ingredient best suited for sugarcane bagasse, which can assist the industry in commercializing ethanol and acetone-butanol-ethanol biofuel from biomass sugarcane. The use of an acetone-butanol-ethanol mixture and ethanol blend in internal combustion engines is also discussed. The literature then supports the proposal of the best operating conditions for fermentation to enhance ethanol and acetone-butanol-ethanol plant efficiency in the sugar waste industry and i... [more]

Accurately measuring carbon dioxide (CO2) emissions is critical for effectively implementing carbon reduction policies, and China’s increased investment in reducing CO2 emissions is expected to significantly impact the world. In this study, the potential of shallow learning for predicting CO2 emissions was explored. Data included CO2 emissions, renewable energy consumption, and the share of primary, secondary, and tertiary industries in China from 1965 to 2021. These time-series data were converted into labeled sample data using the sliding window method to facilitate a supervised learning model for CO2 emission prediction. Then, different shallow learning models with k-fold cross-validation were used to predict China’s short-term CO2 emissions. Finally, optimal models were presented, and the important features were identified. The key findings were as follows. (1) The combined model of RF and LASSO performed best at predicting China’s short-term CO2 emissions, followed by LASSO and SV... [more]

The gas reservoirs in the Northwestern Sichuan Basin have great development potential. However, their production efficiency is seriously reduced by the complex surface multistage throttling process and frequent hydrate plugging caused by the ultra-high-pressure sour gas. Considering the prevention and control of hydrates, properly designing the throttling temperature and pressure to optimize the surface production process is the key to solving this problem. First, this work presents a method for predicting the hydrate formation conditions of ultra-high-pressure sour natural gas based on the vdW-P (van der Waals−Platteeuw) model and the CPA (cubic-plus-association) equation of state (EoS) and considering the association between acid gases (H2S, CO2) and H2O. Secondly, the throttling temperature prediction method was developed by coupling the isenthalpic throttling model and the modified Lee−Kesler EoS mixing rule; the maximum throttling pressure difference calculation method was constru... [more]

The sudden increase in the concentration of carbon dioxide (CO2) in the atmosphere due to the high dependency on fossil products has created the need for an urgent solution to mitigate this challenge. Global warming, which is a direct result of excessive CO2 emissions into the atmosphere, is one major issue that the world is trying to curb, especially in the 21st Century where most energy generation mediums operate using fossil products. This investigation considered a number of materials ideal for the capturing of CO2 in the post-combustion process. The application of aqueous ammonia, amine solutions, ionic liquids, and activated carbons is thoroughly discussed. Notable challenges are impeding their advancement, which are clearly expatiated in the report. Some merits and demerits of these technologies are also presented. Future research directions for each of these technologies are also analyzed and explained in detail. Furthermore, the impact of post-combustion CO2 capture on the cir... [more]

Microbial electrosynthesis is the process of supplying electrons to microorganisms to reduce CO2 and yield industrially relevant products. Such systems are limited by their requirement for high currents, resulting in challenges to cell survival. Electrofermentation is an electron-efficient form of microbial electrosynthesis in which a small cathodic or anodic current is provided to a culture to alter the oxidation−reduction potential of the medium and, in turn, alter microbial metabolism. This approach has been successfully utilised to increase yields of diverse products including biogas, butanediol and lactate. Biomass conversion to lactate is frequently facilitated by ensiling plant biomass with homofermentative lactic acid bacteria. Although most commonly used as a preservative in ensiled animal feed, lactate has diverse industrial applications as a precursor for the production of probiotics, biofuels, bioplastics and platform chemicals. Lactate yields by lactic acid bacteria (LAB)... [more]

Electrifying off-grid and isolated islands in the Philippines remains one of the challenges that hinders community development, and one of the solutions seen to ensure energy security, energy access and promote a low-carbon future is the use of renewable energy sources. This study determines the nearshore wave energy resource during monsoon seasons in Cuyo Island using a 40-year wave hindcast and 8-year on-site wind speed data as inputs to develop a high-resolution wave energy model using SWAN and assesses its annual energy production through matching with wave energy devices. The results show that the average significant wave height (Hs), peak period (Tp) and wave power density (Pd) during a northeast monsoon are Hs = 1.35 m, Tp = 4.79 s and Pd = 4.05 kW/m, respectively, while a southwest monsoon, which is sheltered by the mainland, results in Hs = 0.52 m, Tp = 3.37 s and Pd = 0.34 kW/m. While the simulated model was observed to overestimate the significant wave height (bias = 0.398,... [more]

The Curie point depth (CPD) has been established to enhance the determination of magnetic sources average bottom depth. In this study, the CPD and heat flow regime of the Eratosthenes Seamount in the Eastern Mediterranean were investigated in order to understand the relationship between them. When CPD and heat flow values are determined together, we can understand the types and processes of geothermal resources formation. CPD and heat flow were obtained by applying the spectral analysis method to magnetic data, which was obtained from the Earth Magnetic Anomaly Grid (EMAG2). The result shows that CPD is approximately 22 km across the Seamount and is approximately 9 km in the northern part of the Eratosthenes Seamount near Cyprus. The heat flow regime manifested from CPD is about 95 mW/m2 in the investigated region, where the average thermal conductivity value (k) is considered to be 2.5 W/m °C. The heat flow regime is characterized by an increase in the northward part of the Eratosthen... [more]

The present study provides an energy, exergy and economic analysis of a seawater regasification system (open loop) combining stages of simple organic Rankine cycles (ORCs) arranged in series with an open organic Rankine cycle (OC) in order to exploit the cold energy of liquefied natural gas (LNG). The proposed system, termed ORC-OC, is implemented in a Floating Storage Regasification Unit (FSRU) to achieve the objective of zero greenhouse emissions during the regasification process. Configurations of up to three stages of ORCs and the use of zeotropic mixtures of ethane/propane and n-butane/propane as working fluids are considered in the study of the novel regasification system. Only the two-stage ORC-OC (2ORC-OC) and three-stage (3ORC-OC) configurations accomplish the objective of zero emissions, attaining exergy efficiencies of 61.80% and 62.04%, respectively. The overall cost rate of the latter, however, is 20.85% greater, so the 2ORC-OC results as being more cost-effective. A compa... [more]

The production of biopellets from agricultural residues is an effective method to overcome the expected shortage in the supply of fuel pellets in the future. This work focused on the new potential applications of fuel pellets to produce liquid and gas fuels through thermochemical and hydrothermal biomass-to-gas technologies. The outcomes also provide a basis to compare the effects of steam and hydrothermal gasification techniques on the properties of product and byproduct, as well as their potentials. For steam gasification, the syngas yield increased from 10.7 to 27.8 mmol/g (on a dry and ash-free basis) by a rise in the gasification temperature at a constant steam-to-biomass ratio. In the case of hydrothermal gasification, there was no carbon monoxide, and hydrogen was the main gas product, and with an increase in the temperature, the hydrogen yield rose from 0.4 mmol/g to 3.17 mmol/g with temperatures from 350 to 650 °C. CO had the largest share in the gas product from steam gasific... [more]

Due to high electricity prices and possible shortages of gas and other energy commodities, various fluctuations in electricity generation will need to be regulated. Given the increasing expansion of wind power plants in Europe and worldwide. It is necessary and essential to put power regulation into practice, as mandated by regulation 2016/631 EU. A significant power balance problem may arise on the grid, which may lead to cyclical and recurring blackouts in the future. The motivation for this paper is to raise awareness of the controllability of wind turbines and to highlight the gentle pace of research in this area for pitch angle control. Therefore, the chief idea of the paper is to develop a proposal for wind power plant power control by changing the rotor blade rotation, following previous research in this area, and determining the shortcomings and possibilities. The paper provides a numerical method for controlling the power output of a wind power plant, for which an algorithm ha... [more]

Energy harnessing from renewable energy sources has become more flexible with power electronic technologies. Recent advancements in power electronic technologies achieve converter efficiency higher than 98%. Today, reliable power electronic devices are needed to design a PV-based energy converter (inverter) to reduce the risk of failure and maintenance costs during operation. Wide-bandgap SiC devices are becoming more common in power electronic converters. These devices are designed to reduce switching loss and improve the efficiency of the system. Nevertheless, the cost of SiC devices is a major concern. Hence, to improve the reliability of the PV inverter while considering the economic aspects, this paper develops a highly reliable PV inverter with a hybrid Si/SiC power module that consists of a Si-IGBT with a SiC anti-parallel diode. A test case of a 3 kW PV inverter is considered for reliability analysis. The loading of the PV inverter is done under uncertain environmental conditio... [more]

We propose an experimental study on the influence of the tip speed ratio on the spatial development of a wind turbine wake. To accomplish this, a scaled wind turbine is tested in a wind tunnel, and its turbulent wake measured for streamwise distances between 1 and 30 diameters. Two different tip speed ratios (5.3 and 4.5) are tested by varying the pitch angle of the rotor blades between the optimal setting and one with an offset of +6∘. In addition, we test two Reynolds numbers for the optimal tip speed ratio, ReD=1.9×105 and ReD=2.9×105 (based on the turbine diameter and the freestream velocity). For all cases, the mean streamwise velocity deficit at the centerline evolves close to a power law in the far wake, and we check the validity of the Jensen and Bastankhah-Porté-Agel engineering wind turbine wake models and the Townsend-George wake model for free shear flows for this region. Lastly, we present radial profiles of the mean streamwise velocity and test different radial models. Ou... [more]

AC regenerative electric drives (AC REDs) are widely used in metallurgical rolling due to their reliability, efficiency, and power sufficient to maintain the process. This paper reviews the latest achievements in building the grid connection circuits for the main AC REDs of rolling mills. The paper discusses multipulse connection circuits formed by various transformer types and algorithms for preprogrammed pulse-width modulation with selective harmonic elimination technique (PPWM with SHE) of three-level active front ends (AFE), provides the theoretical and practical measurement results, and gives recommendations for improving existing systems. For 6-, 12-, and 18-pulse grid connection circuits, switching patterns of AFE semiconductor modules with a smooth downward trend within the modulation index range from 0.7 to 1.15 are provided. A simulation was performed under comparable conditions on simulation models in the Matlab/Simulink to objectively evaluate the performance and opportunit... [more]

Issues related to the reduction of the environmental impact of means of road transport by the use of electric motors powered by Proton Exchange Membrane (PEM) fuel cells are presented in this article. The overall functional characteristics of electric vehicles are presented, as well as the essence of the operation of a fuel cell. On the basis of analyzing the energy conversion process, significant advantages of electric drive are demonstrated, especially in vehicles for urban and suburban applications. Moreover, the analyzed literature indicated problems of controlling and maintaining fuel cell power caused by its highest dynamic and possible efficiency. This control was related to the variable load conditions of the fuel cell vehicle (FCV) engine. The relationship with the conventional dependencies in the field of vehicle dynamics is demonstrated. The final part of the study is related to the historical outline and examples of already operating fuel cell systems using hydrogen as an e... [more]

Proton-exchange membrane fuel cells (PEMFCs) are low-temperature fuel cells that have excellent starting performance due to their low operating temperature, can respond quickly to frequent load fluctuations, and can be manufactured in small packages. Unlike existing studies that mainly used hydrogen as fuel for PEMFCs, in this study, methane is used as fuel for PEMFCs to investigate its performance and economy. Methane is a major component of natural gas, which is more economically competitive than hydrogen. In this study, methane gas is reformed by the steam reforming method and is applied to the following five gas post-treatment systems: (a) Case 1—water−gas shift only (WGS), (b) Case 2—partial oxidation reforming only (PROX), (c) Case 3—methanation only, (d) Case 4—WGS + methanation, (e) Case 5—WGS + PROX. In the evaluation, the carbon monoxide concentration in the gas did not exceed 10 ppm, and the methane component, which has a very large greenhouse effect, was not regenerated in... [more]

Developing and underdeveloped countries face innumerable problems related to the accessibility and quality of energy that put the lives of patients, health-care infrastructures, and health workers at risk. Current approaches, such as grid power, unsustainable energy sources such as diesel or gas, and mobile health clinics, have proven insufficient to address this issue. In response, access to reliable health care and electricity has undergone multiple transformations in the last decade, especially in remote and rural areas. Good health and clean energy are two of the 17 United Nations Sustainable Development Goals, originally designed to be a “shared blueprint for peace and prosperity for people and the planet, now and into the future.” Unfortunately, little is known about the interaction between health-care access and energy access in developing and underdeveloped countries, mainly in remote or rural areas. For this reason, this study conducts a review of the literature, including cur... [more]

The building and transportation sectors are responsible for the greatest proportion of energy consumption in cities. While they are intrinsically interlinked with urban built form and density, climate change and technological innovation are having an effect on their relative contributions. This paper aims to develop an optimisation framework to facilitate the identification of the most energy-efficient urban built forms and urban geometry for the future built environment that can be adapted to the changing climate and ongoing technological development. It examines future scenarios for the city of London as a temperate climate zone (as a case study), in 2050, and contrasts it with the present situation. Specifically, the impact of climate change along with the penetration of electric vehicles into the transportation system that can be charged via rooftop photovoltaics is investigated. This study initially develops the geometrical models of four selected urban built forms and, secondly,... [more]

Lithium-ion batteries (LIBs) have been used in many fields, such as consumer electronics and automotive and grid storage, and its applications continue to expand. Several studies have attempted to improve the performance of LIBs. In particular, the use of high-capacity silicon and tin as anodes has been widely studied. Although anodes composed of silicone and tin have high theoretical capacities, poor electrical conductivity and considerable volume expansion of such anodes deteriorate the LIB performance. Thus, Li4Ti5O12 (LTO), a zero-strain material, has attracted much attention with high cycle stability and rate capability through improved electrical conductivity. However, LTO has the disadvantages of a low electrical conductivity (10−8 to 10−13 S cm−1) and moderate Li+ ion diffusion coefficient (10−9 to 10−16 cm2 s−1). In this study, the flexible and free-standing composite films were fabricated using only LTO and multi-walled carbon nanotube(CNT) with high electrical conductivity a... [more]

Recently, the research interest regarding ammonia applications in energy systems has been increasing. Ammonia is an important hydrogen carrier that can also be obtained starting from renewable energy sources. Furthermore, ammonia can be used as a carbon-free fuel in combustion systems. In particular, the behavior of internal combustion engines (ICEs), fueled by ammonia, needs to be further investigated. The main disadvantage of this kind of fuel is its low laminar flame speed when it is oxidized with air. On the other hand, considering a spark-ignition (SI) engine, the absence of knock phenomena could allow a performance improvement. In this work, a 1D numerical approach was used in order to assess the performance and the operating limits of a downsized PFI SI engine fueled with pure ammonia. Furthermore, the reliability of the 1D model was verified by means of a 3D approach. Both throttled and unthrottled engine operation was investigated. In particular, different boost levels were an... [more]

Turbine inlet temperature has continuously increased to improve gas turbine performance during the past few decades. Although internal convection cooling and traditional film cooling have contributed significantly to the current achievement, advanced cooling schemes are needed to minimize the coolant consumption and maximize the cooling efficiency for future gas turbines. This paper conducts a comprehensive review of advanced effusive cooling schemes for gas turbine blades. First, the background and the history of turbine blade cooling are introduced. Then, the metrics of effusive cooling efficiency are defined. Next, effusion cooling, impingement/effusion cooling, and transpiration cooling are reviewed. The flow and heat transfer mechanisms of the cooling schemes are emphasized, and the design trends of the cooling schemes are revealed. Finally, the conclusions and future research perspectives are summarized.

In this work, we investigate the economic viability of demand response (DR) as a balancing option for variable renewable energies, such as wind and solar. Our assessment is based on a highly resolved national energy system model for Germany coupled with a regional DR optimisation model. First, this allows us to determine the spatially resolved flexibility demand, e.g., for avoiding transmission grid congestion. Second, a high number of DR technologies from the residential, commercial and industrial sector, as well as sector coupling, can be considered to cover the regional flexibility demand. Our analysis is based on a scenario for 2035 with a 66% share of renewable energy sources in the power generation. The results show that the largest DR capacity is being installed in the west of Germany, an area with a high density of population and industry. All DR units have an aggregated capacity below 100 MW per transmission grid node. For the economic assessment, we further differentiate betw... [more]

There are three main parts of an electric power system—power generation, transmission, and distribution. For electric companies, it is a tough challenge to reduce losses of the power system and deliver lossless and reliable power from the generating station to the consumer end. Nowadays, modern power systems are more complex due to gradually increasing loads. In the electrical power system, especially in transmission and distribution networks, there are power losses due to many reasons such as overloading of the line, long distribution lines, low power factors, corona losses, and unsuitable conductor size. The main performance factor of the power system is reliability. Reliability means continuity of the power supply without any interruptions from the generating station to the demand side. Thus, due to these power losses, there are voltage stability problems and economic losses in the electrical system. The voltage stability of the power system can be increased by improving the voltage... [more]

Among the many potential future energy sources, hydrogen stands out as particularly promising. Because it is a green and renewable chemical process, water electrolysis has earned much interest among the different hydrogen production techniques. Seawater is the most abundant source of water and the ideal and cheapest electrolyte. The first part of this review includes the description of the general theoretical concepts: chemical, physical, and electrochemical, that stands on the basis of water electrolysis. Due to the rapid development of new electrode materials and cell technology, research has focused on specific seawater electrolysis parameters: the cathodic evolution of hydrogen; the concurrent anodic evolution of oxygen and chlorine; specific seawater catalyst electrodes; and analytical methods to describe their catalytic activity and seawater electrolyzer efficiency. Once the specific objectives of seawater electrolysis have been established through the design and energy performan... [more]

Field operations report that at least half of the fracturing fluid used in shale reservoirs is trapped. These trapped fluids can trigger various geochemical interactions. However, the impact of these interactions on well performance is still elusive. We modeled a hydraulic fracture stage where we simulated the initial conditions by injecting the fracturing fluid and shutting the well to allow the fluids to soak into the formation. Our results suggest a positive correlation between the dissolution and precipitation rates and the carbonate content of the rock. In addition, we observed that gas and load recovery are overestimated when geochemical interactions are overlooked. We also observed promising results for sea water as a good alternative fracturing fluid. Moreover, we observed better performance for cases with lower-saline connate water. The reactions of carbonates outweigh the reactions of clays in most cases. Sensitivity analysis suggests that the concentration of SO4, K and Na i... [more]

The performance of a perovskite-based oxygen carrier for the partial oxidation of methane in thermochemical energy storage applications has been investigated. A synthetic perovskite with formula La0.6Sr0.4FeO3 has been scrutinized for Chemical Looping Reforming (CLR) of CH4 under fixed-bed and fluidized-bed conditions. Temperature-programmed reduction and oxidation steps were carried out under fixed-bed conditions, together with isothermal reduction/oxidation cycles, to evaluate long-term perovskite performance. Under fluidized-bed conditions, isothermal reduction/oxidation cycles were carried out as well. Results obtained under fixed-bed and fluidized-bed conditions were compared in terms of oxygen carrier reactivity and stability. The oxygen carrier showed good reactivity and stability in the range 800−1000 °C. An overall yield of 0.6 Nm3 of syngas per kg of perovskite can be reached per cycle. The decomposition of CH4 catalyzed by the reduced oxide can also occur during the reductio... [more]