One of the most important sources of air pollution, especially in urban areas, is the exhaust emissions from passenger cars. New European emissions regulations, to minimize the gap between manufacturer-reported emissions and those emitted on the road, require new vehicles to undergo emission testing on public roads during the certification process. Outlined in the new regulation are specific boundary conditions to which the route on which the vehicle is driven must comply during a legal test. These boundary conditions, as they relate to the design and subsequent driving of a compliant route, are discussed in detail. The practicality of designing a compliant route is discussed in the context of developing a route on the Gold Coast in Queensland, Australia, in a prescriptive manner. The route itself was driven 5 times and the results compared against regulation boundary conditions.

This paper deals with a small but important component in a building envelope, namely roof windows in pitched roofs. Building physics methods were used to support the search for new solutions which correspond to the maximum extent for requirements for passive house level design. The first part of the paper summarizes the key phenomena of heat transfer, mainly based on a comparison of vertical windows in walls. The results of repeated two-dimensional heat transfer calculations in the form of parametric studies are presented in order to express the most important factors influencing thermal transmittance and minimum surface temperatures. Several configuration variants suitable for technical design are discussed. It was found that a combination of wood and hardened plastics in the window frame and sash is the preferred solution. The resulting thermal transmittance can be up to twice as low as usual (from 0.7 down to 0.5 W/(m2·K), with further development ongoing. Surface temperature requir... [more]

A permanent magnet assisted synchronous reluctance generator (PMA-SynRG) and an induction generator (IG) were compared for portable generator applications. PMA-SynRG with two rotor configurations, namely rotors with ferrite magnet and NdFeB, were designed. Furthermore, a design strategy for both PMA-SynRG and IG is presented with their geometrical dimensions. The machine was designed and results were analyzed using finite element analysis. Results such as flux density, open circuit and full load voltages, torque in generating mode, weight comparison and detailed cost analysis were investigated. In addition, thermal analysis for various ambient conditions (−40 °C, +30 °C, +65 °C) was evaluated for both PMA-SynRG and IG. Furthermore, acoustic versus frequency plot and acoustic pressure level were investigated for both the generators. Finally, the results confirmed that the machine with a higher power-to-weight ratio was the right choice for military applications.

An improved second-order moment bubble-liquid two-phase turbulent model is developed to predict the hydrodynamic characteristics of the shallow bioreactor using two height-to-diameter ratios of H/D = 1.4 and H/D = 2.9. The two-phase hydrodynamic parameters, the bubble normal and shear stress, the bubble energy dissipation rate, the bubble turbulent kinetic energy, etc. were numerically simulated. These parameters increased along with flow direction and constituted a threat to cells living at far distance away from the gas jetting inlet regions, rather than a finding of higher cell damage at near the jetting inlet region, as reported by Babosa et al. 2003. A new correlation named the turbulent energy production of bubble-liquid two-phase flow was proposed to successfully verify this experimental observation. A smaller H/D ratio makes more contributions to the generation of lower turbulent energy productions, which are in favor of the alleviation of cell damage. The extremely long and na... [more]

In order to compensate the large leakage inductance and improve the power transmission capacity, capacitors are widely used in inductive power transfer (IPT) systems, which results in high voltage or current stresses in the resonant tanks and limits higher volt-ampere (VA) rating of the transfer power, especially in medium and low frequency applications. This paper presents a symmetrical half-bridge resonant converter (SHRC) for series-series/series compensated IPT systems with detailed analysis and design. It operates at a relatively low frequency of 12.5 kHz, suitable for IGBT applications. The theoretical analysis shows that, compared with full-bridge resonant converter (FRC) for IPT, the symmetrical half-bridge resonant converter achieves a higher efficiency. Simulation and a prototype of 1500 W power output were built to verify the theoretical analysis. The experimental results show that the power loss of SHRC is 39.7 W while that of FRC is 79.4 W, which is consistent with the the... [more]

The aim of this paper is to present an example of damage to the reheater tubes and conduct the material and numerical analyses to establish the cause of the device failure. Cracks were observed on the first, second, and third tube row. Close to the damaged area, a ferritic structure could be observed with highly degraded bainite areas, characterized by coagulation and coalescence of precipitates. The cause of the damage was analysed using the finite element method (FEM). The big yield of the tube cross-section confirmed that the tube may get damaged during subsequent cycles of the boiler operation, which was also proved by the microstructure testing results. For the reheater under analysis, the tubes have to be lengthened to achieve a reduction in stresses, arising due to thermal loads to values lower than allowable stresses according to Standard EN 13480-3. The modelling results confirmed the correct operation for the upgraded system.

The laboratory test of the wave energy converter model is an important means to evaluate the performance of the device. At present, there are few performance tests for complete specifications under the irregular wave. Referring to the test methods and standards at home and abroad, combined with the actual test work experience in the laboratory, using the irregular wave power calculation formula with the effective wave height and the spectral peak period as parameters, then the wave-wire conversion ratio test method of the wave energy converter physical model under irregular waves in the laboratory is proposed. The method is applied to the basin test experiment of the physical model of the horn-shaped backward bent duct buoy (BBDB) wave energy converter. The research results show that the established test method and process of wave-wire conversion performance have achieved good application results in the irregular waves laboratory test, and can better reflect the device operating charac... [more]

Providing electricity for isolated areas or emergencies (snowstorms, earthquakes, hurricanes, etc.) is an important challenge. In this study, a prototype of a self-powered fan based on a thermoelectric system was built to enhance the heat dissipation of the thermoelectric generator (TEG) systems using household stoves as heat sources. To improve output performance of the system, a heat collector consisting of a heat-conducting flat plate and a heat sink with fan cooling was designed to integrate several thermoelectric modules (TEM). The effects of the fan operating conditions (airflow velocity), number of thermoelectric modules, electrical connection mode under different heat flux among the performance of the TEG system are studied. The data obtained showed a higher heat flux and lower flow velocity are required to realize self-sustained cooling of the system. The maximum electric power is more sensitive to the heat flux than the fan operation conditions. It is also observed that more... [more]

In this study, a boil-off gas reliquefaction system that is a part of liquid ethylene gas (LEG) carriers is evaluated. The reliquefaction system is formed by two thermally interconnected two-stage refrigeration cycles. The working fluid of the bottoming cycle is ethylene; the working fluid of the topping cycle is propylene. The research is based on determining the irreversibilities in the reliquefaction system cycles using the entropy-cycle method of thermodynamic analysis. The impact of the process performance in the main components on the reliquefaction system energy efficiency has been evaluated by the entropy-cycle method. The greatest thermodynamic irreversibility is observed in the two-stage compression process of the bottoming cycle (9%), total throttling irreversibility in the reliquefaction system (8.5%), and vapor superheating at the suction into the low stage of the two-stage compressor of the bottoming cycle (8%). The results of the study showed that it is necessary to impr... [more]

Entropy generation and heat transfer in cavities have received significant interest due to the ever-increasing demand for enhancing thermal performances in many scientific and engineering fields. In particular, nanofluids are being used increasingly in engineering applications and real-life problems, as they exhibit significantly better thermal properties than basic heat transfer fluids, for example, water, oil, or ethylene glycol. This study investigates the entropy generation and heat transfer of a nanofluid in a confined cavity with a moving top wall and a rectangular fin at the bottom. Here, a macro-homogeneous model based on a previously developed model is employed for investigating the mixed convective flow and heat transfer of CuO-water nanofluid. Various fin geometries, Rayleigh numbers, Reynolds numbers, and nanofluid concentrations have been employed. Present results indicate that the heat transfer rate can be improved, while entropy generation can be minimized using nanoflui... [more]

The purpose of this paper is to address an urgent operational issue referring to optimal power flow (OPF), which is associated with a number of technical and financial aspects relating to issues of environmental concern. In the last few decades, OPF has become one of the most significant issues in nonlinear optimization research. OPF generally improves the performance of electric power distribution, transmission, and production within the constraints of the control system. It is the purpose of an OPF to determine the most optimal way to run a power system. For the power system, OPFs can be created with a variety of financial and technical objectives. Based on these findings, this paper proposes the peafowl optimization algorithm (POA). A powerful meta-heuristic optimization algorithm inspired by collective foraging activities among peafowl swarms. By balancing local exploitation with worldwide exploration, the OPF is able to strike a balance between exploration and exploitation. In ord... [more]

Based on the total carbon emission data of 30 provinces and cities in China from 2000 to 2020, this paper used non-parametric kernel density estimation and traditional and spatial Markov probability transfer matrix methods to explore the temporal and spatial dynamic evolution characteristics of carbon dioxide emissions in China and then used a super-SBM model to calculate the carbon emission reduction potential of each province. The results showed that: (1) from 2000 to 2020, the total carbon emissions in China showed an upward trend of fluctuation, from 1.35 Gt to 4.90 Gt year by year, with an annual growth rate of 13.10%. (2) The core density curve showed a double peak form of “main peak + right peak,” indicating that a polarization phenomenon occurred in the region. (3) The overall trend of carbon dioxide emissions shifting to superheavy carbon emissions was significant, and the probability of transition was as high as 74.69%, indicating that it was challenging to achieve leapfrog t... [more]

This paper presents a novel analytical loss formulation to predict the efficiency of three-phase inverters using silicon carbide (SiC) metal—oxide—semiconductor field-effect transistors (MOSFETs). The proposed analytical formulation accounts for the influence of the output current harmonic distortion on the conduction losses as well as the impact of the output parasitic capacitances and the deadtime on the switching losses. The losses are formulated in balanced conditions to select suitable SiC MOFETs for the desired target efficiency. To validate the proposed methodology, a 3-phase inverter is designed to present full load efficiency in excess of 99% when built using SiC MOSFETs antiparalleled with SiC Schottky diodes selected for the specified full load efficiency. Experimental assessment of the designed inverter efficiency is compared with the expected values from the proposed analytical formulation and shown to match or exceed the predicted results for loads ranging from 40% to 100... [more]

The speech intelligibility properties of classrooms greatly influence the learning process of students. Proper acoustics can promote the inclusion of foreign students and children with learning or hearing impairments. While awareness of the topic is increasing, there is still no parameter that can describe all aspects of speech transmission inside a room. This complicates the design of classrooms and requires designers to have extensive knowledge of theory and experience. In the scientific and technical literature, there is a lack of predictive tools, easy to use by designers, which can guide the choices in the early design stages in order to move towards technical solutions able to ensure adequate levels of speech intelligibility. For this reason, in this paper, the most relevant speech intelligibility parameters found in the literature were collected and discussed. Among these, the Clarity index and Speech Transmission Index were singled out as the most effective ones, whose predicti... [more]

Promoting efficiency of liquid−liquid extraction at a high pH is a main challenge for the recovery of volatile fatty acids (VFAs) from organic wastes. In this study, the extraction efficiency of VFAs from artificial solution and acidification fermentation broth of kitchen wastes using ionic liquids (ILs) was assessed at high pH. The effect of ILs addition ratio in diluent, volumetric solvent to feed ratio (S/F) on extraction efficiency were investigated. The solvent consists of [P666,14][Cl] (IL101) and dodecane was found to be the promising solvent for VFA extraction at pH 6.0, especially for butyric acid. The IL-101 ratio in dodecane and S/F was significant factors for the liquid−liquid extraction of VFAs. In general, a higher IL-101 ratio and S/F can promote the extraction efficiency of single VFAs. As a result, the maximum extraction rate of acetic acid (38.4−49.9%) and butyric acid (66.0−92.1%) from different VFA concentration solutions was observed at 10% IL-101 in dodecane and S... [more]

Mineral carbonation incurs high operating costs, as large amounts of chemicals and energy must be used in the process. Its implementation on an industrial scale requires reducing expenditures on chemicals and energy consumption. Thus, this work aimed to investigate the significant factors involved in pH-swing mineral carbonation and their effects on CO2 capture efficiency. A central composite rotatable design (CCRD) was employed for optimizing the operational parameters of the acid dissolution of serpentinite. The results showed that temperature exerts a significant effect on magnesium dissolution. By adjusting the reaction temperature to 100 °C and setting the hydrochloric acid concentration to 2.5 molar, 96% magnesium extraction was achieved within 120 min of the reaction and 91% within 30 min of the reaction. The optimal efficiency of carbon dioxide capture was 40−50%, at higher values than those found in literature, and 90% at 150 bar and high pressures. It was found that it is tec... [more]

Outdoor air conditioning systems (ACS) are used as autonomic systems as well as in combined outdoor and indoor ACS of the variable refrigerant flow (VRF) type, with variable speed compressors (VSC) as their advanced version. Methods for determining the optimal value of refrigeration capacity and providing the maximum rate of the summarized annual refrigeration energy generation increment, according to its needs at minimum compressor sizes and rational values, are applied to reveal the reserves for reducing the designed (installed) refrigeration capacity, thus enabling us to practically achieve maximum annual refrigeration energy generation as the primary criterion at the second stage of the general design methodology previously developed by the authors. The principle of sharing the total thermal load on the ACS between the ranges of changeable loads for outdoor air precooling, and a relatively stable load range for further processing air are used as its basis. According to this princip... [more]

The energy transition requires increased end-user flexibility in consumption as a response to the more volatile production patterns of renewable resources. Automated demand-side management solutions can provide support in achieving this but struggle with trust and acceptance issues from end-users. This paper contributes insights into how communicating trustworthiness can be achieved through careful and context-aware interaction design in such systems. Core interface features such as feedback, automation transparency, control options, benefit information, and actionable information were identified and fifteen case studies from six countries were analysed with regard to provided interaction features, automation level, and end-user experiences. The results provide insights into the form and frequency of these features used at different automation levels and their varying role in trust and acceptance building. Based on our results, we recommend particular attention to providing actionable... [more]

The geological storage of carbon dioxide (CO2) is the most suitable option to achieve a large-scale and low-cost CO2 emissions worldwide, but the selection of favorable areas for the geological storage is the main issue. In this study, evaluation indicators were selected considering four aspects, namely geological conditions, storage potential, hydrogeological conditions, and engineering conditions, based on drilling, geophysical, and geochemical data from the Beibu Gulf Basin. The analytical hierarchy process and the fuzzy comprehensive evaluation method were used to evaluate the suitability of this basin for geological storage of CO2. The results suggested that: (1) the Beibu Gulf Basin is suitable for CO2 geological storage, and the evaluation grade is the highest rating level; (2) considering the techno-economic feasibility, it is necessary to select the target area for CO2 geological storage with suitable burial depth, superior reservoir conditions, proximity to the CO2 collection... [more]

The building industry is responsible for a significant degree of energy consumption in the world, causing negative climate changes and energy supply uncertainties due to low energy efficiency as well as the high resource demand of construction. Consequently, energy design optimization has become an important research field. Passive design strategies are one of the most definitive factors concerning energy-related building development. The given architectural problem calls for a method that can create all potentially feasible building geometries, thus guaranteeing the optimal solution which is addressed in the current paper. To reach this requirement, the necessity of a modular space arrangement system and architectural selection rules were determined, focusing on the relationship between the rules and the generation of geometries with mathematical rigor. Next, the architecture-based congruency analysis performed, further reduced the number of simulation cases. With the simulations, it... [more]

Electromagnetics is the hidden ‘glue’ that holds together almost all electrical and electronic engineering applications [...]

Water displacing oil is one of the main emptying methods for mobile pipelines. It has the advantages of being a simple process and highly safe. At present, the determination of a water displacing oil scheme of mobile pipelines is based on the oil−oil alternating transport theory of product oil pipelines. However, the insolubility of the oil phase and the water phase results in a great difference between the flow characteristics of water displacing oil and the oil−oil alternating transport of a product oil pipeline. In addition, due to the effect of buoyancy, the oil phase gathers at the high point of the pipeline and forms a liquid accumulation, which is difficult to carry away by water flow, resulting in the low emptying efficiency of the mobile pipeline. The essence of water displacing oil in a mobile pipeline is an oil−water two-phase unsteady displacement flow, involving liquid−liquid displacement flow, oil−water two-phase flow and water carrying oil. Aiming at such problems, domes... [more]

Optimization-based design tools for energy systems often require a large set of parameter assumptions, e.g., about technology efficiencies and costs or the temporal availability of variable renewable energies. Understanding the influence of all these parameters on the computed energy system design via direct sensitivity analysis is not easy for human decision-makers, since they may become overloaded by the multitude of possible results. We thus propose transferring an approach from explaining complex neural networks, so-called locally interpretable model-agnostic explanations (LIME), to this related problem. Specifically, we use variations of a small number of interpretable, high-level parameter features and sparse linear regression to obtain the most important local explanations for a selected design quantity. For a small bottom-up optimization model of a grid-connected building with photovoltaics, we derive intuitive explanations for the optimal battery capacity in terms of different... [more]

Wave energy provides a renewable and clear power for the future energy mix and fights against climate change. Currently, there are many different wave energy converters, but their costs of extracting wave energy are still much higher than other matured renewables. One of the best indicators of calculating the generating cost of wave energy is the ‘levelized cost of energy’ (LCOE), which is the combined capital expenditure (CAPEX), operational expenditure (OPEX), and decommissioning cost with the inclusion of the annual energy production, discount factor, and project’s lifespan. However, the results of the LCOE are in disagreement. Hence, it is important to explore the cost breakdown of wave energy by the wave energy converter (WEC), so for finding potential ways to decrease the cost, and finally compare it with other renewable energies. Different WECs have been installed in the same place; the Wave Dragon LCOE platform is the best one, with an energy conversion of EUR 316.90/MWh, follo... [more]

The currently still high fossil energy demand is forcing the glass industry to search for innovative approaches for the reduction in CO2 emissions and the integration of renewable energy sources. In this paper, a novel power-to-methane concept is presented and discussed for this purpose. A special focus is on methods for the required CO2 capture from typical flue gases in the glass industry, which have hardly been explored to date. To close this research gap, process simulation models are developed to investigate post-combustion CO2 capture by absorption processes, followed by a techno-economic evaluation. Due to reduced flue gas volume, the designed CO2 capture plant is found to be much smaller (40 m3 absorber column volume) than absorption-based CO2 separation processes for power plants (12,560 m3 absorber column volume). As there are many options for waste heat utilization in the glass industry, the waste heat required for CO2 desorption can be generated in a particularly efficient... [more]