As environmental regulations have been strengthened worldwide since the Paris Climate Agreement, the automobile industry is shifting its production paradigm to focus on eco-friendly vehicles such as electric vehicles and hydrogen-battery vehicles. Governments are banning fossil fuel vehicles by law and expanding the introduction of green vehicles. The energy efficiency of electric vehicles that use a limited power source called batteries depends on the driving environment. Applying a two-speed transmission to an electric vehicle can optimize average speed and performance efficiency at low speeds, and achieve maximum speed with minimal torque at high speeds. In this study, a two-speed transmission for an electric vehicle has been developed, to be used in a compact electric vehicle. This utilizes a planetary gear of a total of three pairs, made of a single module which was intended to enable two-speed. The ring gear was removed, and the carrier was used in common. When shifting, the ener... [more]

Electricity companies around the world are constantly seeking ways to provide electricity more safely and efficiently while reducing the negative impact on the environment. Mineral oils have been the most popular transformer insulation, having excellent electrical insulating properties, but have many problems such as high flammability, significant cleaning problems, and are toxic to fish and wildlife. This paper presents an alternative approach to mineral oil: a transformer design that is clean and provides better performance and environmental benefits. A 50 kVA, 34.5/0.4 kV gas insulated distribution transformer was designed and evaluated using the COMSOL Multiphysics environment. R410A was used as insulation material. R410A is a near-azeotropic mixture of difluoromethane (CH2F2, called R-32) and pentafluoro ethane (C2HF5, called R-125), which is used as a refrigerant in air conditioning applications. It has excellent properties including environmentally friendly, no-ozone depletion,... [more]

Recently, due to regulations on emissions of vessels, fuel is changing to liquefied natural gas (LNG). When using LNG as fuel, it is advantageous in terms of fuel saving and boil-off gas control if a small-scale liquefaction process is installed on the ship. However, due to the limited space, the small-scale liquefaction process for ships has to consider not only efficiency but also simplicity and compactness. In this respect, it is different from the process in onshore liquefaction plants, and research on this is insufficient. Therefore, this paper performs a comparative analysis in terms of efficiency by simplifying the composition of the mixed refrigerant in the liquefaction process. Additionally, a single mixed refrigerant process is used to pursue the compactness of the process. For comparative analysis, the liquefaction process is designed and simulated, and the specific power consumption calculated as the power required to liquefy the unit LNG is used as the objective function t... [more]

Transverse flux motors (TFMs) are being investigated to be used in vehicle traction applications due to their high torque density. In this paper, a two-phase axial-gap transverse flux motor is designed for an electric scooter, proposing a novel analytical design method. First, the dimensioning equations of the motor are obtained based on the vehicle requirements, and the stationary dq model is calculated. Then, the motor is optimized using a multiobjective genetic algorithm, and finally a 3D-FEM verification is made. Both the motor structure and the design method aim to have a low complexity, in order to favor the sizing and manufacturing processes through a low computation time and simple core shapes. This approach has not yet been explored in axial-gap TFMs.

Urban Waste Heat Recovery, heat recovery from low-temperature urban sources such as data centres and metro systems, has a great deal of potential in terms of meeting domestic and commercial heat demands whilst significantly reducing carbon emissions. Urban sources of heat are advantageous in that they tend to be close to areas of high heat demand and are therefore highly suitable as inputs to existing and newly constructed district heating networks. This paper has two main focuses. Firstly, the issue of efficiency in waste heat recovery is addressed with a focus on Technical, Economic, Social, and Environmental (TESE) efficiencies, which we consider should be given equal consideration. Secondly, we address the question of contractual efficiency and argue that contracts should be underpinned by mathematical modelling. We then focus on the contractual relationship between the owner of the waste heat and the district heating operator and consider the question of waste heat pricing. We sug... [more]

In this paper, a study on the feasibility of the treatment of raw cheese whey by anaerobic co-digestion using coffee pulp residues as a co-substrate is presented. It considers raw whey generated in artisanal cheese markers, which is generally not treated, thus causing environmental pollution problems. An experimental design was carried out evaluating the effect of pH and the substrate ratio on methane production at 35 °C (i.e., mesophilic conditions). The interaction of the parameters on the co-substrate degradation and the methane production was analyzed using a response surface analysis. Furthermore, two kinetic models were proposed (first order and modified Gompertz models) to determine the dynamic profiles of methane yield. The results show that co-digestion of the raw whey is favored at pH = 6, reaching a maximum yield of 71.54 mLCH4 gVSrem−1 (31.5% VS removed) for raw cheese whey and coffee pulp ratio of 1 gVSwhey gVSCoffe−1. The proposed kinetic models successfully fit the exper... [more]

Packaging was recently identified as an essential element in addressing the key challenge of sustainable food supply and is gaining interest among researchers. It is a central element in food quality preservation due to its role in heat and mass exchange with the external atmosphere, contributing to the preservation of food quality during storage and extending food shelf life. This work proposes three new packaging configurations with the same size but different geometry and ventilation hole sizes and geometry, that change the conditions in which the heat and mass exchange occurs, during either the cooling period of fruits, inside the cooling chamber, or during the period when the packaging is exposed to ambient conditions, outside the cooling chamber. For this purpose, packages with fruit models that replicate the properties of real fruit were subjected to a cooling process inside a cooling chamber for 8 h. Subsequently, during the heating phase, the packages were exposed to ambient c... [more]

We designed and implemented a single-switch step-up DC-DC converter based on cascaded boost and Luo converters. The proposed converter demonstrated a quadratic voltage gain and a high efficiency, which makes it suitable for renewable energy applications, where a high voltage gain ratio is desired without imposing a high number of bulky items or employing a high duty cycle of the active switches. This converter benefits from the continuity of the input current waveform, which equips the maximum utilisation of renewable energy sources. While a transformer-less high voltage-gain was achieved, the voltage and current stresses of the power switch and diodes were kept low in comparison with the existing quadratic DC-DC converters. We analysed the converter in both continuous and discontinuous conduction modes. A non-ideal model of components was considered for power loss and efficiency calculations and comparisons. Finally, the simulation results were extracted with PLECS and validated with... [more]

In 2007, the US Department of Energy recommended a no-go on NaBH4 hydrolysis for onboard applications; however, the concept of a NaBH4-H2-PEMFC system has the potential to become a primary source for on-demand power supply. Despite the many efforts to study this technology, most of the published papers focus on catalytic performance. Nevertheless, the development of a practical reaction system to close the NaBH4-H2 cycle remains a critical issue. Therefore, this work provides an overview of the research progress on the solutions for the by-product rehydrogenation leading to the regeneration of NaBH4 with economic potential. It is the first to compare and analyze the main types of processes to regenerate NaBH4: thermo-, mechano-, and electrochemical. Moreover, it considers the report by Demirci et al. on the main by-product of sodium borohydride hydrolysis. The published literature already reported efficient NaBH4 regeneration; however, the processes still need more improvements. Moreov... [more]

Pedestrians are participants and, most likely, fatalities in every third road traffic accident in Poland. Over 30% of all fatalities on Polish roads are pedestrians. Accidents with pedestrians are very often the result of various factors related to the infrastructure and behaviour of pedestrians and drivers. The objective of the work was to assess driver and pedestrian behaviour in pedestrian crossing areas. The research also served as a pilot study for similar work to be conducted across Poland, and constituted the basis for monitoring the behaviour of road users in the area of pedestrian crossings. Parameters which must be analysed were identified on the basis of field studies. Principles of selecting test sites were adopted, and measurement methods for pedestrian crossing areas are presented. The influence of the location of the selected test cross-section infrastructure parameters on the behaviour of road users in pedestrian crossing areas is demonstrated. The results of the study... [more]

To identify the trends in new flexibility markets, a set of market and aggregator platforms were selected and compared. The analyzed initiatives are relevant to consider alternative designs for European electricity markets. This review proposes a common methodology for analyzing these market models by comparing their description, market structure, market timing, and implementation. Furthermore, a range of policy implications and future research directions towards implementing these markets are presented. The results provide compelling evidence that the new market models represent a promising business with technical and economic justification, as they incentivize the uptake of flexibility from distributed resources by providing services to Distribution System Operators (DSOs) in coordination with Transmission System Operators (TSOs). Moreover, the interactions between these new market platforms and existing markets are of particular interest, and the contributions from aggregator platfo... [more]

Occupant behavior can significantly influence the operation and performance of buildings. Many occupant-centric key performance indicators (KPIs) rely on having accurate counts of the number of occupants in a building, which is very different to how occupancy information is currently collected in the majority of buildings today. To address this gap, the authors develop a standardized methodology for the calculation of percent space utilization for buildings, which is formulated with respect to two prevalent operational data schemas: the Brick Schema and Project Haystack. The methodology is scalable across different levels of spatial granularity and irrespective of sensor placement. Moreover, the methods are intended to make use of typical occupancy sensors that capture presence level occupancy and not counts of people. Since occupant-hours is a preferable metric to use in KPI calculations, a method to convert between percent space utilization and occupant-hours using the design occupan... [more]

Proper selection and application of interfacial friction factor correlations has a significant impact on prediction of key flow characteristics in gas−liquid two-phase flows. In this study, experimental investigation of gas−liquid flow in a vertical pipeline with internal diameter of 0.060 m is presented. Air and oil (with viscosities ranging from 100−200 mPa s) were used as gas and liquid phases, respectively. Superficial velocities of air ranging from 22.37 to 59.06 m/s and oil ranging from 0.05 to 0.16 m/s were used as a test matrix during the experimental campaign. The influence of estimates obtained from nine interfacial friction factor models on the accuracy of predicting pressure gradient, film thickness and gas void fraction was investigated by utilising a two-fluid model. Results obtained indicate that at liquid viscosity of 100 mPa s, the interfacial friction factor correlation proposed by Belt et al. (2009) performed best for pressure gradient prediction while the Moeck (197... [more]

Energy harvesting is a promising approach to power novel instrumented implants that have passive sensory functions or actuators for therapeutic measures. We recently proposed a new piezoelectric concept for energy harvesting in total hip replacements. The mechanical implant safety and the feasibility of power generation were numerically demonstrated. However, the power output for the chosen piezoelectric element was low. Therefore, we investigated in the present study different geometry variants for an increased power output for in vivo applications. Using the same finite element model, we focused on new, customised piezoelectric element geometries to optimally exploit the available space for integration of the energy harvesting system, while maintaining the mechanical safety of the implant. The result of our iterative design study was an increased power output from 29.8 to 729.9 µW. This amount is sufficient for low-power electronics.

Although products can contribute to ecosystems positively, they can cause negative environmental impacts throughout their life cycles, from obtaining raw material, production, and use, to end of life. It is reported that most negative environmental impacts are decided at early design phases, which suggests that the determination of product sustainability should be considered as early as possible, such as during the conceptual design stage, when it is still possible to modify the design concept. However, most of the existing concept evaluation methods or tools are focused on assessing the feasibility or creativity of the concepts generated, lacking the measurements of sustainability of concepts. The paper explores key factors related to sustainable design with regard to environmental impacts, and describes a set of objective measures of sustainable product design concept evaluation, namely, material, production, use, and end of life. The rationales of the four metrics are discussed, wit... [more]

Electricity supply quality (ESQ) is critical for healthy economic production, and regional differences in ESQ can widen economic development gaps. To contribute to a more equitable regional development, this study first develops a Gini index of ESQ distribution to measure the inequality among different cities. Then, an econometric model based on the Cobb−Douglas production function is established to quantify the effects of ESQ on regional economy. Finally, we estimate the impacts of ESQ improvement on reducing the economic inequality. The main results show that: (1) Substantial differences exist among the regional ESQ, and the national GDP-based ESQ Gini index was 0.720 in 2018. (2) A GDP-based Lorenz curve has a higher Gini coefficient than the population-based one does, while inequalities in cites are greater than those in rural areas. (3) The ESQ has significant impacts on the regional economic output, and a 1% reduction in the ESQ will, on average, reduce the city-level output by 0... [more]

A comprehensive monitoring program is an integral part of the safe operation of geological CO2 storage projects. Noble gases can be used as geochemical tracers to detect a CO2 anomaly and identify its origin, since they display unique signatures in the injected CO2 and naturally occurring geological fluids and gases of the storage site complex. In this study, we assess and demonstrate the suitability of noble gases in source identification of CO2 anomalies even when natural variability and analytical uncertainties are considered. Explicitly, injected CO2 becomes distinguishable from shallow fluids (e.g., subsea gas seeps) due to its inheritance of the radiogenic signature (e.g., high He) of deep crustal fluids by equilibration with the formation water. This equilibration also results in the CO2 inheriting a distinct Xe concentration and Xe/noble gas elemental ratios, which enable the CO2 to be differentiated from deep crustal hydrocarbon gases that may be in the vicinity of a storage r... [more]

China intends to develop its renewable energy sector in order to cut down on its pollution levels. Concentrated solar power (CSP) technologies are expected to play a key role in this agenda. This study evaluated the technical and economic performance of a 100 MW solar tower CSP in Tibet, China, under different heat transfer fluids (HTF), i.e., Salt (60% NaNO3 40% KNO3) or HTF A, and Salt (46.5% LiF 11.5% NaF 42% KF) or HTF B under two different power cycles, namely supercritical CO2 and Rankine. Results from the study suggest that the Rankine power cycle with HTF A and B recorded capacity factors (CF) of 39% and 40.3%, respectively. The sCO2 power cycle also recorded CFs of 41% and 39.4% for HTF A and HTF B, respectively. A total of 359 GWh of energy was generated by the sCO2 system with HTF B, whereas the sCO2 system with HTF A generated a total of 345 GWh in the first year. The Rankine system with HTF A generated a total of 341 GWh, while the system with B as its HTF produced a total... [more]

In order to explore the changes that autonomous vehicles would bring to the current traffic system, we analyze the car-following behavior of different traffic scenarios based on an anti-collision theory and establish a traffic flow model with an arbitrary proportion (p) of autonomous vehicles. Using calculus and difference methods, a speed transformation model is established which could make the autonomous/human-driven vehicles maintain synchronized speed changes. Based on multi-hydrodynamic theory, a mixed traffic flow model capable of numerical calculation is established to predict the changes in traffic flow under different proportions of autonomous vehicles, then obtain the redistribution characteristics of traffic flow. Results show that the reaction time of autonomous vehicles has a decisive influence on traffic capacity; the q-k curve for mixed human/autonomous traffic remains in the region between the q-k curves for 100% human and 100% autonomous traffic; the participation of a... [more]

This paper develops simplifying entropic models of irreversible closed cycles. The entropic models involve the irreversible connections between external and internal main operational parameters with finite physical dimensions. The external parameters are the mean temperatures of external heat reservoirs, the heat transfers thermal conductance, and the heat transfer mean log temperatures differences. The internal involved parameters are the reference entropy of the cycle and the internal irreversibility number. The cycle’s design might use four possible operational constraints in order to find out the reference entropy. The internal irreversibility number allows the evaluation of the reversible heat output function of the reversible heat input. Thus the cycle entropy balance equation to design the trigeneration cycles only through external operational parameters might be involved. In designing trigeneration systems, they must know the requirements of all consumers of the useful energies... [more]

Wastewater and sewage sludge contain organic matter that can be valorized through conversion into energy and/or green chemicals. Moreover, resource recovery from these wastes has become the new focus of wastewater management, to develop more sustainable processes in a circular economy approach. The aim of this review was to analyze current sewage sludge management systems in Scandinavia with respect to resource recovery, in combination with other organic wastes. As anaerobic digestion (AD) was found to be the common sludge treatment approach in Scandinavia, different available organic municipal and industrial wastes were identified and compared, to evaluate the potential for expanding the resource recovery by anaerobic co-digestion. Additionally, a full-scale case study of co-digestion, as strategy for optimization of the anaerobic digestion treatment, was presented for each country, together with advanced biorefinery approaches to wastewater treatment and resource recovery.

The underlying objective of the paper is to identify and evaluate in the research process vital factors that impact the development of design and construction enterprises of photovoltaic farms on the energy markets, in particular narrowed down to renewable energy sources (RES) markets, including energy coming from photovoltaic sources. The first part of the paper, the epistemological one, introduces a scientific discourse pertaining to conditionings and restrictions related to RES markets in the dimensions of sustainable development. This has been done with the use of literature query, legislative and administrative acts, and reports drawn up for the European Commission. In this reference, we summarized the EU’s essential measures aimed at promoting the idea of sustainability. The second part of the paper, the empirical one, presents a summary of the results obtained within the research pertaining to “opportunities and threats in managing projects of photovoltaic farms in production en... [more]

Gas-fired heat pumps are a potential replacement for condensing boilers, utilizing fossil-fuel resources more efficiently and reducing the amount of biogas or hydrogen required in sustainable gas grids. However, their adoption has been limited due to their large size and high capital cost, resulting in long payback times. For adsorption-based heat pumps, the major development challenge is to maximize the rate of heat transfer to the adsorbent, whilst minimizing the thermal mass. This work develops a modular finned-tube carbon−ammonia adsorption generator that incorporates the adsorbent in highly compacted 3-mm layers between aluminum fins. Manufacturing techniques that are amenable to low cost and high-volume production were developed. The module was tested using the large temperature jump (LTJ) method and achieved a time constant for adsorption and desorption of 50 s. The computational model predicted that if incorporated into two adsorption generators of 6 L volume each, they could b... [more]

There is very little knowledge on the occupant actual hot water comfort (temperature and flow), usage practice, and routines (temporal and spatial distribution of hot water usage in a household). This paper describes the results from the total and hot water measurements in two Danish detached houses. The results show that, at the draw-off points, the temperature of 55 °C is never asked by the occupants, not even in the kitchen sink. The domestic water temperature differentiates depending on the function of the draw-off point, with the shower and kitchen taps being most energy- and water-intense. They constitute around 90% of the hot water use in the house. Shower units on average demand for highest temperature (i.e., 35.5 °C to 40.4 °C). Hand washing operates, on average, at temperature between 20.5 °C to 26.5 °C. Average water temperature at the taps located in utility room varies between 23 °C to 26 °C. These in-depth insight in the total and hot water use in two new-built low energy... [more]

The multi-winding medium frequency transformer (MMFT) has attracted widespread attention, since its application in power electronic transformers can simplify the system structure and reduce the volume and weight. However, the special working conditions of MMFT due to high voltage and high power density increase the difficulty of insulation design for MMFT. For this issue, this paper presents a comprehensive analysis of electric filed characteristics for MMFT. First, the electric field model of MMFT is established using the 2-D finite element method. Based on it, the influences of connection mode, core structure, and hollow winding on the electric field characteristics of MMFT are studied, including the overall electric field distribution, maximum electric field intensity, and the electric field intensity along a fixed path. The results show that there are differences in the maximum electric field intensity for different connection modes and different core structures, which provides ref... [more]