In buildings, the HVAC systems are responsible for a major part of the energy consumption. Incorrect design or selection of the system and improper installation, operation, and maintenance of the systems’ elements may result in increased energy consumption. It is worth remembering that the main aim of the appropriate system is to maintain the high quality of the indoor environment. Appropriate selection of the HVAC solution ensures both thermal and quality parameters of the air, independently of the internal and external heat loads. The microclimate of a room is affected not only by air temperature, humidity, and purity, but also by air velocity in the occupied zone. The proper air velocity distribution prevents discomfort, particularly at workstations. Based on the measurements in the office building, an analysis of velocity profiles of air supplying two different types of linear diffusers was carried out. The analysis was made based on the results of measurements performed with therm... [more]

Despite the technology for wood biomass combustion being much more advantageous when compared to traditional burners, such as the Stoker or fluidized burner, there has been scant research on the topic of wood biomass cyclone burners. The purpose of this paper is to review biomass cyclone burner technology, which includes theory, design, and combustion, in terms of the chemistry and properties of wood biomass, emission related to NOx and CO, and application of the burner, such as co-firing with coal and gasification firing. The design factors for type 2 cyclone burners have been identified through the following three dimensionless numbers: swirl intensity (S), Strouhal number (St), and Reynolds number (Re). The lowest CO and NOx of type 2 cyclone burners have been sought for pulverized and non-pulverized wood biomass. The benefits of the co-firing of wood biomass in a cyclone burner with coal, have been presented in respect to combustion efficiency, alkali retention, and the amount of K... [more]

This paper investigates the factors that determine the profitability of non-listed energy firms from four central European countries: Hungary, Poland, Slovakia, and the Czech Republic. We apply the regression analysis, on a large panel of firm-year observations for the 2015−2019 timespan, to verify the hypothesis on the inversed relationship between leverage and profitability of the companies performing in the energy sector. Our results support the inversed relationship for debt in total and long-term debt, which are consistent with the assumptions of the pecking order theory. However, for short-term debt, we have found a direct relationship, which confirms the assumptions of the trade-off theory of capital structure. Our work contributes to the existing debate on the interplay between financial leverage and profitability, by providing evidence for a large panel of non-listed firms, from a single sector (energy)-oriented perspective.

Eliminating environmental and air pollution is one of the European Union’s priority actions in the field of transport. Poland, as a member of the European Community, is also actively involved in these activities. The flagship project, the implementation of which is expected to bring tangible effects in this respect, is the “Sustainable Transport Development Strategy until 2030”. It states that in 2030 there should be 600,000 BEVs (battery electric vehicles) on Polish roads. At present, the share of such vehicles in the automotive market in Poland is small, which is a result of a number of barriers. One of them, very important considering the preferences of Poles, is the cost of buying such a car, which is currently at least 40% higher than its counterpart with a combustion engine. Meanwhile, popularizers of electric cars believe that the cost of buying such a vehicle is offset by the subsequent costs associated with its operation. Hence, this paper determines and then compares the tota... [more]

Globally, buildings account for nearly 40% of the total primary energy consumption and are responsible for 20% of the total greenhouse gas emissions. Energy consumption in buildings is increasing with the increasing world population and improving standards of living. Current global warming conditions will inevitably impact building energy consumption. To address this issue, this report conducted a comprehensive study of the impact of climate change on residential building energy consumption. Using the methodology of morphing, the weather files were constructed based on the typical meteorological year (TMY) data and predicted data generated from eight typical global climate models (GCMs) for three representative concentration pathways (RCP2.6, RCP4.5, and RCP8.5) from 2020 to 2100. It was found that the most severe situation would occur in scenario RCP8.5, where the increase in temperature will reach 4.5 °C in eastern Australia from 2080−2099, which is 1 °C higher than that in other cli... [more]

Electric vehicles (EVs) are currently emerging as alternative vehicles due to their high energy efficiency and low emissions during driving. However, regarding the raising concern, the safety of EVs can further be improved before they completely replace conventional vehicles. This paper focuses on reviewing the safety requirements of EVs, especially those powered by Li-ion battery, based on the mechanical abuse tests from the international standards, national standards, regulations and other laboratories standards, and safety of occupants from the regulations and safety programs. Moreover, the publicly reported real-world fire incidents of EVs based on road crashes were collected and reviewed. The objective is to highlight the gap and challenges arose between the current safety requirements and real-world fire incidents of EVs and provide the way for assisting the future research in the area of EV safety, particularly light duty passenger vehicle. The serious challenges observed includ... [more]

In recent years, induction heating (IH) applications aided by electronic power control have gained significance. Particularly, for cooking applications, an appropriate control technique is required to feed power from a single source to multiple loads with minimum switching losses. Additionally, when multiple loads are used, it requires independent control and operation for each of the loads. The main idea of this work is to develop a single-stage AC-AC converter topology to feed power to multiple loads independently with a single source, with a reduced number of switching devices and with minimum switching losses. The proposed topology uses a frequency bifurcation concept to feed power to multiple loads by placing the transmitting coil and work coil at a distance of 3 cm. The source is resonated at a 25 kHz switching frequency, with the designed bifurcated frequencies of 20 kHz and 33 kHz. The resonant capacitors are appropriately chosen to operate at those frequencies. For real-time a... [more]

We describe the external and internal hydrogen interaction on contacting surfaces in the “cylinder−piston rings” friction coupling. Under the influence of high temperatures and pressure, the oil in the combustion chamber at a temperature up to 1473 K decomposes and forms small amounts of water. External hydrogen (H2) is subsequently formed. Hydrogen removal from the piston rings reduces the heterogeneity of the structure, residual stresses, and uneven physical and chemical properties of the near-surface layers, which reduces the stress concentration and, as a consequence, results in an improvement in the performance characteristics of the surface layers of the friction couple “cylinder-piston rings” of the spark ignition engine.

Non-geminate recombination, as one of the most relevant loss mechanisms in organic and perovskite solar cells, deserves special attention in research efforts to further increase device performance. It can be subdivided into first, second, and third order processes, which can be elucidated by the effects that they have on the time-dependent open-circuit voltage decay. In this study, analytical expressions for the open-circuit voltage decay exhibiting one of the aforementioned recombination mechanisms were derived. It was possible to support the analytical models with experimental examples of three different solar cells, each of them dominated either by first (PBDBT:CETIC-4F), second (PM6:Y6), or third (irradiated CH3NH3PbI3) order recombination. Furthermore, a simple approach to estimate the dominant recombination process was also introduced and tested on these examples. Moreover, limitations of the analytical models and the measurement technique itself were discussed.

Electromobility has gained significance over recent years and the requirements on the performance and efficiency of electric vehicles are growing. Lithium-ion batteries are the primary source of energy in electric vehicles and their performance is highly dependent on the operating temperature. There is a compelling need to create a robust modeling framework to drive the design of vehicle batteries in the ever-competitive market. This paper presents a system-level modeling methodology for thermal simulations of large battery packs for electric trucks under real-world operating conditions. The battery pack was developed in GT-SUITE, where module-to-module discretization was performed to study the thermal behavior and temperature distribution within the pack. The heat generated from each module was estimated using Bernardi’s expression and the pack model was calibrated for thermal interface material properties under a heat-up test. The model evaluation was performed for four charging/disc... [more]

Outages in an overhead power distribution system are caused by multiple environmental factors, such as weather, trees, and animal activity. Since they form a major portion of the outages, the ability to accurately estimate these outages is a significant step towards enhancing the reliability of power distribution systems. Earlier research with statistical models, neural networks, and committee machines to estimate weather-related and animal-related outages has reported some success. In this paper, a deep neural network ensemble model for outage estimation is proposed. The entire input space is partitioned with a distinct neural network in the ensemble performing outage estimate in each partition. A novel algorithm is proposed to train the neural networks in the ensemble, while simultaneously partitioning the input space in a suitable manner. The proposed approach has been compared with the earlier approaches for outage estimation for four U.S. cities. The results suggest that the propo... [more]

Only recently, smart cities are taking shape, thanks to the rapid development of Internet of Things (IoT), cloud computing, and other similar technologies. Given the high demands placed on advanced technologies such as autonomous driving, cloud data services, and high-precision sensors, smart cities are creating an intelligent transportation environment conducive to the introduction of autonomous vehicles (AVs). In this context, the use of AVs in transportation is also considered a form of transportation innovation. As a result, AVs are considered more favorable to people interested in new technologies because they appear to be technologically superior. Their association with the most up-to-date technology can serve as a symbol for those who wish to demonstrate their interest in new technologies through their appearance. The positive image of technological innovation projected by AVs may influence their acceptance among technology enthusiasts to a significant degree. In this context, t... [more]

Offshore wind-turbine support structures are largely made of steel since steel monopiles have accounted for the majority of installations in the last decade. As turbines become bigger, steel structures have led to an exponential increase in material and installation costs. From this point of view, the use of concrete for future support structures has been initiated. In this study, concrete−steel composite piles have been investigated. A pre-tensioned high strength concrete pile was placed in the lower part, mainly to support the axial load, and a steel pile in the upper part to resist the lateral load. A mechanical joint was adapted to connect the two different types of piles. Static axial, dynamic axial, and lateral load tests were performed to evaluate the load-displacement response of the composite pile, verify the integrity of the mechanical joint, and investigate its potential application to offshore wind foundations. This paper focused on the load-displacement response and the co... [more]

Based on the experimental studies, the process of ground regeneration around the borehole loaded with brine-water heat pumps working exclusively for heating purposes in the period of four consecutive heating seasons in a cold climate was presented. The research was conducted in north-eastern Poland. The aim of the work is to verify the phenomenon of thermal ground regeneration in the period between heating seasons on the basis of the recorded data and to check whether the ground is able to regenerate itself and at what rate. It was noticed that the ground does not fully regenerate, especially during heating seasons with lower temperatures. In the analyzed period, from 22 September 2016 to 12 October 2020, the ground probably cooled irreversibly by 1.5 °C. In order to illustrate and evaluate the speed of changes in the ground, the one’s profile with an undisturbed temperature field was presented for each month of the year. The presented results can be a very important source of informat... [more]

In this study, the influence of architectural design parameters (the exterior window area, the wall height at a corridor-side, and the door gap of a toilet unit) on the airflow patterns and malodorous volatile substance (acetic acid) distributions within toilet units were investigated via computational fluid dynamics (CFD), with the restrooms in K−12 public schools (kindergarten through grade 12) of Taiwan as research objects. The results show that when there is a 2 m/s north wind in winter, all the cases exceed the required 12 air changes per hour (ACH), and most are above 43.75 ACH. When there is a 0.5 m/s south wind in summer, nearly half of the cases fail to reach 12 ACH. Maintaining an adequate natural ventilation rate and an acceptable level of odor pollution through passive design and architectural design is difficult. Thinking about how to improve the ventilation efficiency of toilet units with the aid of simple, appropriate, and energy-saving mechanical ventilation approaches... [more]

In this paper, we investigate implications of running a cooling system of two silicagel/water adsorption chillers powered by a district heating network. The devices are connected in series, i.e., the heating water output from the primary chiller is directed to the secondary one. In consequence, the secondary device must deal with an even lower driving temperature and with temperature fluctuations caused by the primary device. We have evaluated three factors that influence the operation of those coupled devices: synchronization of their operating cycles, selection of their cycle time allocations (CTAs), and changing the heating water mass flow rate. Numerical analyses indicate that the performance of the secondary chiller drops significantly if the coupled devices that use the same CTA run asynchronously. The decrease is largest if the shift between the operating cycles is x=0.375 and x=0.875. We found that it is possible to reduce the negative influence of the asynchronous operation by... [more]

The induced draft (ID) fan is an important piece of auxiliary equipment in coal-fired power plants. Early fault detection of the ID fan can provide predictive maintenance and reduce unscheduled shutdowns, thus improving the reliability of the power generation. In this study, an adaptive model was developed to achieve the early fault detection of ID fans. First, a non-parametric monitoring model was constructed to describe the normal operating characteristics with the multivariate state estimation technique (MSET). A similarity index representing operation status was defined according to the prediction deviations to produce warnings of early faults. To deal with the model accuracy degradation because of variant condition operation of the ID fan, an adaptive strategy was proposed by using the samples with a high data quality index (DQI) to manage the memory matrix and update the MSET model, thereby improving the fault detection results. The proposed method was applied to a 300 MW coal-fi... [more]

The property sector is revitalised to incorporate sustainability, specifically the biophilic design, to encourage human interaction with nature. Thus, there is an urgent need to communicate the biophilic design elements amongst stakeholders, especially the foreign workers, to ensure the project meets the requirement. However, standard project communications management is no longer practical, as the construction industry worldwide has been severely impacted by the Coronavirus Disease 2019 (COVID-19) pandemic. Hence, this paper evaluates the biophilic design elements to be communicated and examines the project communications management breakdown relating to the biophilic design elements in the Malaysian construction industry during the COVID-19 pandemic. Through a systematic literature review (SLR), focus group discussion (FGD) and questionnaire survey on 147 foreign workers, this paper found that from 33 biophilic design element items, only 1 item is categorised as highly critical, wher... [more]

This paper presents an occupant-centric theory of buildings’ indoor-environmental control systems and their user interfaces. Buildings typically can have multiple devices and systems to maintain indoor-environmental conditions within certain ranges in order to meet occupants’ health and comfort requirements. Therefore, it is important to understand what those ranges are exactly, who defines them, and for whom. Health and comfort sciences offer some broad directions concerning desirable indoor conditions. These are typically formulated in various codes, standards, and guidelines in terms of target values or the set points of control variables. However, preferable conditions may differ at different times and for different individuals. Another question concerns the agency responsible for maintaining the preferred conditions. In some settings, conditions may be centrally controlled via the buildings’ automation systems, whereas in other settings, occupants might have the possibility to con... [more]

There are significant concerns regarding the stability of increased wind power generation in weak power grids. This paper investigates and improves the stability of Wind Turbine Squirrel Cage Induction Generators (WT-SCIGs) with series compensation and weak interconnections to the power grid. Detailed time-domain and state-space modeling have revealed new bifurcations and oscillatory modes for a WT-SCIG connected radially to a weak grid through a series compensated line. The stability domain analyses are carried out by computing bifurcations in the system by analyzing eigenvalues of the linearized system. The analyses demonstrate for the first time how the degree of compensation at which the Hopf bifurcation occurs depends on the X/R ratio of the line, operating slip of the induction generator, and voltage regulator parameters as well as the time delays in measurements. A new damping controller is proposed, which greatly improves the dynamic stability of the WT-SCIG and eliminates dest... [more]

Various algorithms predominantly use data-driven methods for forecasting building electricity consumption. Among them, algorithms that use deep learning methods and, long and short-term memory (LSTM) have shown strong prediction accuracy in numerous fields. However, the LSTM algorithm still has certain limitations, e.g., the accuracy of forecasting the building air conditioning power consumption was not very high. To explore ways of improving the prediction accuracy, this study selects a high-rise office building in Shanghai to predict the air conditioning power consumption and lighting power consumption, respectively and discusses the influence of weather parameters and schedule parameters on the prediction accuracy. The results demonstrate that using the LSTM algorithm to accurately predict the electricity consumption of air conditioners is more challenging than predicting lighting electricity consumption. To improve the prediction accuracy of air conditioning power consumption, two... [more]

In a naturally saturated state, rocks are likely to be in a stress field simultaneously containing static and dynamic loads. Since rocks are more vulnerable to tensile loads, it is significant to characterize the tensile properties of naturally saturated rocks under coupled static−dynamic loads. In this study, dynamic flattened Brazilian disc (FBD) tensile tests were conducted on naturally saturated sandstone under static pre-tension using a modified split-Hopkinson pressure bar (SHPB) device. Combining high-speed photographs with digital image correlation (DIC) technology, we can observe the variation of strain applied to specimens’ surfaces, including the central crack initiation. The experimental results indicate that the dynamic tensile strength of naturally saturated specimens increases with an increase in loading rate, but with the pre-tension increases, the dynamic strength at a certain loading rate decreases accordingly. Moreover, the dynamic strength of naturally saturated san... [more]

The Songliao Basin (SLB) is a large terrestrial petroliferous basin located in northeastern China. The Nenjiang Formation represents excellent hydrocarbon source rocks for the Daqing oil field. Previous studies have indicated that the oil shale intervals from the first (K2n1) and second (K2n2) members of the Nenjiang Formation were formed in different depositional settings. In this study, we provide a new high-resolution (1 m interval) record from SK-1s core and compile three sets of published datasets from two drilling holes (Zk3389 and LY-1) and a composite outcrop section. According to the total organic carbon (TOC) chemostratigraphy, we have divided three variation cycles spanning from K2n1 to K2n2 and detected three potential oil shale intervals in the Nenjiang Formation. Combined with the productivity, salinity, and oxygenation proxies, we discuss the paleolimnological environmental changes during deposition of the Nenjiang Formation. Our new and compiled records support the mode... [more]

This paper proposes a method for the optimal placement of phasor measurement units (PMUs) for the complete observability of a power system based on the degree of the neighbourhood vertices. A three-stage algorithm is used to determine the minimum number of PMUs needed to make the system observable. The key objective of the proposed methodology is to minimize the total number of PMUs to completely observe a power system network and thereby minimize the installation cost. In addition, the proposed technique also focuses on improving the measurement redundancy. The proposed method is applied on standard IEEE 14-bus, IEEE 24-bus, IEEE 30-bus, IEEE 57-bus and IEEE 118-bus test systems and a hybrid AC/DC microgrid test system. The results obtained are compared with already existing methods in terms of the Bus Observability Index (BOI) and System Observability Redundancy Index (SORI). The results show that the proposed method is simple to implement and provides better placement locations for... [more]

This article deals with the new challenges facing modernising railways in Poland. We look at the problem of the efficiency of the power supply system (3 kV DC) used in the context of the increasing use of electric vehicles, which have a higher demand for electricity than the old type. We present and characterise the power supply system in use, pointing out its weaknesses. We consider a case study. The load of the power supply network generated by the rolling stock used in Poland was examined using a microsimulation. A real train timetable was taken into account on a fragment of one of the most important railway line sections in one of the urban agglomerations. Then the results were compared with the results of a microsimulation in which old units were replaced by new trains. These tests were carried out in several variants. We found critical points in the scheduling of railway system use. Our results indicate that it is becoming increasingly necessary to take into account the permissib... [more]