This concept study extends the power-to-gas approach to small combined heat and power devices in buildings that alternately operate fuel cells and electrolysis. While the heat is used to replace existing fossil heaters on-site, the power is either fed into the grid or consumed via heat-coupled electrolysis to balance the grid power at the nearest grid node. In detail, the power demand of Germany is simulated as a snapshot for 2030 with 100% renewable sourcing. The standard load profile is supplemented with additional loads from 100% electric heat pumps, 100% electric cars, and a fully electrified industry. The renewable power is then scaled up to match this demand with historic hourly yield data from 2018/2019. An optimal mix of photovoltaics, wind, biomass and hydropower is calculated in respect to estimated costs in 2030. Hydrogen has recently entered a large number of national energy roadmaps worldwide. However, most of them address the demands of heavy industry and heavy transport,... [more]

Forced oscillation events have become a challenging problem with the increasing penetration of renewable and other inverter-based resources (IBRs), especially when the forced oscillation frequency coincides with the dominant natural oscillation frequency. A severe forced oscillation event can deteriorate power system dynamic stability, damage equipment, and limit power transfer capability. This paper proposes a two-dimension scanning forced oscillation grid vulnerability analysis method to identify areas/zones in the system that are critical to forced oscillation. These critical areas/zones can be further considered as effective actuator locations for the deployment of forced oscillation damping controllers. Additionally, active power modulation control through IBRs is also proposed to reduce the forced oscillation impact on the entire grid. The proposed methods are demonstrated through a case study on a synthetic Texas power system model. The simulation results demonstrate that the cr... [more]

Hydraulic fracturing is an important means of developing unconventional oil and gas layers. The fracture conductivity of tight sandstone reservoirs after fracture is affected by many factors, such as the interaction between the fracturing fluid, water, and rocks; the fracturing materials; and the construction parameters. This paper improves the experimental process of the long-term conductivity test and provides insight into conductivity prediction and optimization based on the response surface test method. The test process is conducted in the following manner: (1) inject nitrogen to evaluate the fracture conductivity before fracturing fluid damage; (2) inject fracturing fluid to simulate shut-in; and (3) inject nitrogen again to evaluate fracture conductivity after the damage ability of the fracturing fluid. The single factor test results show that the lower the sand concentration is, the higher the fracturing fluid viscosity will be, and the longer the fracturing fluid retention time... [more]

Transport is one of the most important sources of environmental pollution. More and more information has shown that one of the greatest sources of emissions from transport are emissions related to the release of microplastics from tyres. This is one of the most underestimated sources of emissions into the environment. In this study, environmental samples are analysed for the presence of these particles. For this purpose, optical methods and spectroscopic methods are used. Fourier transform infrared (FTIR) spectroscopy is used to identify synthetic rubber, most likely derived from car tyres. A complementary confocal microscopy method is used to confirm the FTIR results. The soil samples and road dust from the areas with heavy traffic are tested. An average of 372 ± 50 fragments per kilogram dry weight are detected in the soil samples. In the case of samples from the road, this number is 515 ± 20 fragments per kilogram of dry matter. In the samples, most of the microplastics come from ty... [more]

Thermomagnetic heat engines were designed, constructed, and tested, where numbers of gadolinium (Gd) blocks were used to exploit low temperature waste heat. Gadolinium is a rare earth material whose magnetic property changes with temperature, altering between ferromagnetic and paramagnetic. A motion develops in the thermomagnetic heat engine as Gd blocks are exposed to different temperatures causing changes in their magnetic property. A change in the magnetic property of any Gd block is directly related to the resultant torque driving the thermomagnetic heat engine for power production. Among heat engines studied to date, the cylindrical thermomagnetic heat engine was able to develop a maximum mechanical power of 1.1 W at a temperature difference of 45 °C between hot and cold thermal resources. Furthermore, depending on the effectiveness of an electromagnetic generator (EMG) combined with a triboelectric nanogenerator (TENG), the electric power output can be notably improved.

Space cooling demand is increasing globally due to climate change. Cooling has also been linked to all 17 sustainable development goals of the United Nations. Adequate cooling improves productivity and thermal comfort and can also prevent health risks. Meanwhile, policy initiatives such as the European Union’s Green Deal require participants to cut greenhouse gas emissions and reduce energy use. Therefore, novel cooling systems that are capable of efficiently producing high levels of thermal comfort are needed. Radiant cooling systems provide a design capable of fulfilling these goals, but their application in hot and humid climates is limited due to the risk of condensation. In this study, we compare the performances of radiant cooling systems with and without dehumidification. The studied systems are supplied by geothermal energy. The study is conducted using building energy models of a small office building belonging to a three-building school complex located in Sant Cugat near Barc... [more]

A laudable goal toward achieving autonomous internet of things (IoT) devices would be to use the same circuitry for communication and harvesting energy. One way to achieve it is through simultaneous lightwave and power transfer (SLIPT) that consists of using solar cells to harvest energy and receive information signals. Here, a SLIPT-based system that uses a large area solar panel to harvest energy from light sources and decode data signals is designed. The designed system is equipped with an infrared sensor used to detect the movements of an unmanned aerial vehicle. We equally discuss the wide-scale deployment of IoT devices with SLIPT capability.

In pipelines for transporting oil and gas, multiple cracks often exist in weld joints. The interaction among the cracks should be considered as it directly affects the life span of the pipeline structures. In the current investigation, based on the fluid−solid magnetic coupling model, the virtual crack-closure technique (VCCT) is applied to systematically study the multi-crack dynamic interaction effect on pipeline welds during the crack propagation process. The results show that the existence of an auxiliary crack accelerates the main crack’s propagation. When the auxiliary crack is nearer to the main crack tip, the enhancement effect of the auxiliary crack on the main crack increases. Further, when the initial length of the auxiliary crack increases, the main crack becomes easier to propagate. Two important parameters, the distance between the two interacting crack tips and the initial size of the auxiliary crack, are studied in detail. Their interference effect on the main crack has... [more]

The aim of the work was to prepare and test a paper-oil insulation system according to the recommendations of CIGRE (Conseil International des Grands Réseaux Électriques) with the parameters X = 50% and Y = 30%. Pressboard was moistened to a water content of (5.0 ± 0.2) wt.% The loss tangent was measured using a DIRANA meter (FDS-PDC dielectric response analyzer) in the frequency range 10−4 Hz−5000 Hz for 6 temperatures from 293.15 K to 333.15 K with a step of 8 K. The waveforms simulated by the DIRANA software were fitted to the experimental dependence of the loss tangent. The fitting process was performed using two methods. In the first method, the measuring temperature value as well as X and Y values were entered into the software. The estimated moisture content of the insulation varied from about 1.4 to about 5.2 wt.%. The average value of moisture content was (3.73 ± 1.11) wt.%. In the second method, only the measuring temperature value was entered into the software. This improved... [more]

The work describes a systematic optimization strategy for designing hypersonic inlet intakes. A Reynolds-averaged Navier-Stokes database is mined using genetic algorithms to develop ideal designs for a priori defined targets. An intake geometry from the literature is adopted as a baseline. Thus, a steady-state numerical assessment is validated and the computational grid is tuned under nominal operating conditions. Following validation tasks, the model is used for multi-objective optimization. The latter aims at minimizing the drag coefficient while boosting the static and total pressure ratios, respectively. The Pareto optimal solutions are analyzed, emphasizing the flow patterns that result in the improvements. Although the approach is applied to a specific setup, the method is entirely general, offering a valuable flowchart for designing super/hypersonic inlets. Notably, because high-quality computational fluid dynamics strategies drive the innovation process, the latter accounts for... [more]

Islanding detection is one of the conditions necessary for the safe operation of the microgrid. The detection technology should provide the ability to differentiate islanded operations from power grid disturbances effectively. Given that it is difficult to set the fault threshold using the passive detection method, and because the traditional active detection method affects the output power quality, a microgrid islanding detection method based on the Sliding Window Discrete Fourier Transform (SDFT)-Empirical Mode Decomposition (EMD) and Long Short-Term Memory (LSTM) network optimized by an attention mechanism is proposed. In this paper, the inverter output current and voltage at the point of common coupling (PCC) are transformed by the SDFT. The positive sequence, zero sequence, and negative sequence components of voltage and current harmonics are calculated and reconstructed by adopting the symmetrical component method (SCM). Meanwhile, the current and voltage are decomposed into a mo... [more]

The objective of this study is to develop a statistical model to accurately estimate the total base number (TBN) value of diesel engine oils on the basis of the Fourier transform infrared spectroscopy (FTIR) analysis. The research sample consisted of oils used in the course of 14,820 km. The samples were collected after each 1000 km and both FTIR and TBN measurements were performed. By applying the measured absorbance values, five statistical models aimed at predicting TBN values were elaborated with the use of the following information: aggregated values of measured absorbance in defined spectral ranges, extremes at wavenumbers, or the surface area of spectral bands related to the vibrations of specific molecular structures. The obtained models may be considered a continuation and an extension of previous studies of this type described in the literature on the subject. The results of the study and the analysis of the obtained data have led to the development of two models with high pr... [more]

In renewable energy source applications, multilevel inverters with lower power components have become more popular in recent decades. This work exhibits a novel topology for high-quality output in PV applications, along with low-power switches and isolated dc sources. The core module of the suggested design may create a 13-level output waveform with two unequal voltage source values. The cascaded structure is intended to boost the voltage levels, and the related parameters are obtained analytically. The even and odd levels of voltage can be created natively without the usage of an additional H bridge circuit. Furthermore, the switches, gate driver circuits, dc sources, and standing voltage are fewer in number when compared to other recent topologies. Power losses and cost comparisons are calculated and given in monetary terms. This new research supports the idea that nearest level control (NLC) is used as a modulation scheme in the simulation modeling and experimental validation of the... [more]

Permeability in porous media has an important role in many engineering applications, which depends mainly on the pore size, distribution, and connectivity of porous media. As the pore structure distribution of coal has a multi-scale fractal dimension characteristic, this study aimed to propose a multi-scale fractal dimension characteristics units model (MFU) to describe the pore structure distribution by analyzing the multi-scale fractal dimension characteristics of coal pore media. Then, a multi-scale fractal permeability model was established based on MFU. The pore structure distribution was obtained by mercury injection porosimetry (MIP) and nuclear magnetic resonance (NMR) experiments. Based on MIP and NMR experimental data, the permeability contribution of different pore diameters were calculated. The results show that the permeability contribution of the micropore was minimal and can be ignored. The permeability contribution of mesopores was about 1−5%, and the permeability contr... [more]

The relationship between wind speed and the power produced by a wind turbine is expressed by its power curve. Power curves are commonly used to monitor the production performance of a wind turbine by asset managers to ensure optimal production. They can also be used as a tool to detect faults occurring on a wind turbine when the fault causes a decrease in performance. However, the wide dispersion of data generally observed around the reference power curve limits the detection performance of power curve-based techniques. Fault indicators, such as residuals, which measure the difference between the actual power produced and the expected power, are largely affected by this dispersion. To increase the detection performance of power-based fault detection methods, a hybrid solution of mono-multi-turbine residual generation is proposed in this paper to reduce the influence of the power curve dispersion. A new simulation framework, modeling the effect of wind nature (turbulent/laminar) on the... [more]

In this work, two methods were investigated for determining the composition of carbonate solvent systems used in lithium-ion (Li-ion) battery electrolytes. One method was based on comprehensive two-dimensional gas chromatography with electron ionization time-of-flight mass spectrometry (GC×GC/EI TOF MS), which often enables unknown compound identification by their electron ionization (EI) mass spectra. The other method was based on comprehensive two-dimensional gas chromatography with flame ionization detection (GC×GC/FID). Both methods were used to determine the concentrations of six different commonly used carbonates in Li-ion battery electrolytes (i.e., ethylene carbonate (EC), propylene carbonate (PC), dimethyl carbonate (DMC), diethyl carbonate (DEC), ethyl methyl carbonate (EMC), and vinylene carbonate (VC) in model compound mixtures (MCMs), single-blind samples (SBS), and a commercially obtained electrolyte solution (COES). Both methods were found to be precise (uncertainty <... [more]

Spectrum demand has increased with the rapid growth of wireless devices and wireless service usage. The rapid development of 5G smart cities and the industrial Internet of Things makes the problem of spectrum resource shortage and increased energy consumption even more severe. To address the issues of high energy consumption for spectrum sensing and low user access rate in the cognitive radio networks (CRN) model powered entirely by energy harvesting, we propose a novel energy harvesting (EH)-distributed cooperative spectrum sensing (DCSS) architecture that allows SUs to acquire from the surrounding environment and radio frequency (RF) signals energy, and an improved distributed cooperative spectrum sensing scheme based on energy-correlation is proposed. First, we formulate an optimization problem to select a leader for each channel; then formulate another optimization problem to select the corresponding cooperative secondary users (SUs). Each channel has a fixed SUs cluster in each ti... [more]

Policy-makers should focus on solar energy due to the increasing energy demand and adverse consequences such as global warming. Conflicting criteria influence choosing the most desirable place to construct a Solar Power Plant (SPP). Researchers have popularized multicriteria decision-making (MCDM) methods because of the potential. Although the simultaneous use of several methods increases the robustness and accuracy of the results, existing methods to integrate MCDM methods mainly consider the same weight for all methods and utilize the alternatives ranking for the final comparison. This paper presents a hybrid decision-making framework to determine the best location for SPPs in Iran using a set of criteria extracted from the literature and expert opinions. An initial list of decision-making alternatives is prepared and evaluated using GIS software in terms of criteria. Decision-makers prioritized the identified alternatives using the MCDM methods, including SWARA and different ranking... [more]

With the increase in capacitor voltage transformer (CVT) operation life, CVT impedance changes, and the short-time switching of overhead lines, it is very easy to cause a transient oscillation accident in which a CVT participates, reduce the insulation level of a CVT, and even induce regional power grid oscillation and easily cause capacitor breakdown, after long-term operation with defects. In this paper, the whole power network, including the generator, power grid, and consumer, is modeled, and the theoretical model of the CVT ferro-resonance connected grid is built. The frequency spectrum analysis, and the measurements of resonance bus voltage and line voltage, were carried out to find the design method of a fast saturation damper (FSD) and its voltage−current characteristics that affect the vibration, based on theory and practice; this paper puts forward effective measures to reduce the resonance effect of a CVT in operation, and avoid the oscillation of the line and even the regio... [more]

The uncertain output of variable renewables adds significant challenges to the generation of affordable, reliable, and sustainable power sources in a country or region. Therefore, we propose a new stochastic nonlinear multi-objective model to optimize the power generation structure in 31 provinces of China. Considering variable renewable integration, we use Monte Carlo simulation to describe the randomness and uncertainty of renewable power output. The learning curve in the exponential expression is used to describe the nonlinear relationship between generation cost and installed capacity. The optimized results show that China can substitute fossil power with clean power. Renewable power will account for more than 42% of total power in the optimal power generation structure in 2040. In particular, the annual average growth rate of non-hydro renewable generation is expected to be 12.06%, with solar photovoltaic (PV) power growing the most by 17.95%. The share of renewable power exceeds... [more]

Solar air heater is considered to be the most popular and widely used solar thermal system. Solar air heater (SAH) can be used in many applications, ranging from domestic to industrial purposes. However, it seems that the viability of SAH is not feasible due to the following two reasons: (i) the low convective heat transfer coefficient at the absorber plate is the reason that causes a low heat transfer rate to the flowing air, and (ii) the high temperature of the absorber plate insists on high heat losses, thus, reducing the thermal efficiency. The convective coefficient can be augmented by placing turbulators/roughness on the absorber plate, which induces turbulence in the flow passage near the absorber plate by disrupting and destabilizing the laminar sublayer. This comprehensive review has been presented to summarize the studies on artificial roughness/turbulators geometries to enhance the heat transfer rate. Various rib configurations (such as grits, grooves, blockages, baffles, wi... [more]

Nitrogen−oxygen sensors are pivotal for NOX emission detection, and they have been designed as key components in vehicles’ exhaust systems. However, severe thermal stress concentrations during thermal cycling in the sensors create knotty structural damage issues, which are inevitable during the frequent start−stop events of the vehicles. Herein, to illustrate the effect of thermal concentration on a sensor’s structure, we simulated the temperature and stress field of a sensor through finite element analysis. The failure modes of the sensor based on the multilayer structure model were analyzed. Our simulation indicated that the thermal deformation and stress of the sensors increased significantly when the heating temperature in the sensors increased from 200 to 800 °C. High stress regions were located at the joint between the layers and the right angle of the air chamber. These results are consistent with the sensor failure locations that were observed by SEM, and the sensor’s failures... [more]

In recent years, solar power has developed significantly in Vietnam, making an important contribution to ensuring energy conservation and decreasing greenhouse gas exposure. Recently, Vietnam has experienced impressive growth in the solar and wind energy sectors, showing the high potential of using renewable electricity in addressing energy needs. The target of this study was to construct a fuzzy multicriteria decision-making, model including strengths-weaknesses-opportunities-challenges (SWOC) analysis, the fuzzy analytic hierarchy process (F-AHP) model, and the weighted aggregates sum product assessment (WASPAS) model, to select the location of a solar power plant in south Vietnam. The proposed fuzzy multicriteria decision-making model (MCDM) model is the first solar power plant location selection in southern Vietnam that utilizes literature reviews and expert interviews. Moreover, this is the first study to provide a case study on evaluating locations during solar power plant locati... [more]

Energy communities, also known as renewable or citizen energy communities, can be a source of innovative aggregation solutions at the local level. The unleashed flexibility potential of households could provide self-balancing services for local energy communities or create new revenue streams for local flexibility aggregators. This paper proposes a methodology for the assessment of the energy savings potential of residential customers, factoring in local climatological conditions, energy consumption patterns, and building energy performance when the available input data are scarce. For baseline consumption modelling, the correlation between historical energy consumption data collected from a survey, building energy performance parameters, and the availability of flexibility assets was determined, taking into account the inconsistency between the quantity and quality of collected data from various consumers. For this purpose, a modelling approach using calculations for “Agent” buildings... [more]

Due to the complex working medium of oil in construction engineering, the waterproof valve in mixing machinery can easily cause different degrees of failure. Moreover, under adverse working conditions and complicated noise backgrounds, it is very difficult to detect the fault of waterproof valves. Thus, a fault diagnosis method is proposed, especially for the fault detection of waterproof valves as a key component in the construction of mixing machinery. This fault diagnosis method is based on a new adaptive feature extraction model, with multi-path signals to the improved deep residual shrinkage network−stacked denoising convolutional autoencoder (named DRSN−SDCAE). Firstly, the noisy vibration signals collected by the two vibration sensors are preprocessed, and then transmitted to the parallel structure improved DRSN−SDCAE for adaptive denoising and feature extraction. Finally, these results are fused through the feature fusion strategy to realize the effective fault diagnosis of the... [more]