This paper proposes the analysis and design of the linear active disturbance rejection controller (LADRC) for the pitch angle model of a large wind turbine generator (WTG). Since the transfer function of the pitch control system exhibits nonminimum-phase characteristics, the parameters of LADRC are difficult to tune using the conventional bandwidth method. On the basis of PI controller parameters to first-order LADRC parameters, an optimization problem is proposed in this paper to find the parameters of an LADRC for the pitch control system under the constraint of robustness measure, and the extremum-seeking (ES) algorithm is used to solve the problem. Simulation results show that LADRC can achieve better tracking and disturbance rejection performance than traditional PI control without loss of robustness against time delay.

Polymer electrolyte membrane fuel cells are emerging as an important research topic owing to increasingly intensified environmental pollution. The flow field pattern of the fuel cell controls the electrochemically uniform distribution and water flooding in the reaction area between the anode and cathode. Water discharge management in the channel is an important factor influencing the efficiency of the fuel cell. In this paper, we propose a polymer electrolyte fuel cell with a rotatable circular spiral channel set to a constant size. The mass transfer behavior was analyzed numerically according to the number of channel passes. Numerical analysis showed that the production and behavior of water are closely associated with the performance of fuel cells. The circular spiral-pattern fuel cell with the greatest membrane water content was rotated through the experimental device to confirm the performance change of the fuel cell for each rotation speed. The performance improved as the internal... [more]

Humanity is exceeding planetary boundaries, and it seems that it is unlikely to meet internationally agreed sustainable development goals. Current trends and challenges in the domain of urban sustainability assessment have proven that measuring and interpreting results regarding quality of life requires a complex analysis. The aim of this paper is to investigate the possibility of comparing, in a transparent way, urban quality of life using sustainable development indicators based on the ISO 37120 standard, taking as case studies seven selected cities: Amsterdam, Buenos Aires, Dubai, Gdynia, London, Los Angeles and Zagreb. The hypothesis reads as follows: the ISO 37120 indicators, converted into partial and total utility value, then grouped within sustainable development dimensions (environmental, economic and social) may be used to measure the level of urban quality of life. Research results indicate that there are some significant and interesting differences between the compared citi... [more]

In this paper, a methodology for short-term forecasting of power generated by a photovoltaic module is reported. The method incorporates a nonlinear autoregressive with exogenous inputs (NARX) fed by the solar radiation and temperature times series, as well as an estimation of power time series obtained by implementing an ideal single diode model. This synthetic time series was validated against an actual photovoltaic module. The NARX model has been implemented in conjunction with the corrective vector multiplier (CVM) technique, which uses solar radiation under clear sky conditions to adjust the forecasting results. In addition, collinearity and the Granger causality tests were used to choose the input variables. The forecasting horizon was 24-h-ahead. The hybrid NARX-CVM model was compared to a nonlinear autoregressive neural network and persistence model using the typic forecasting error measures such as the mean bias error, mean squared error, root mean squared error and forecast s... [more]

In the coming decades, energy from offshore wind turbines is expected to be an important energy source in electric power systems [...]

Electric water heaters, which have the capacity to act as thermal energy storage, are well suited to demand management strategies in smart grid applications. However, finding the balance between managing power load, reducing thermal energy losses, user’s convenience, and bacterial growth control, requires accurate modelling of the internal thermal dynamics of the tank, including stratification. As a black box, this unknown is dependent on a multitude of environmental factors (e.g., ambient temperature and inlet temperature), water draw patterns, scheduling, set temperatures and orientation of the vessel. The latter affects the stratification and temperature variation inside the tank, and therefore has a direct bearing on the balancing act of demand management. Although this has been assessed inside vertically oriented tanks, what happens inside the horizontal variety—ubiquitous in developing countries—is currently left to the guesswork. In this paper, we present the development of an e... [more]

A study on the capacity increase of a power converter according to the increase in the single capacity of wave energy converters and four-leg topology that can supply stable power even under unbalanced load conditions during independent operation is required. Therefore, in this paper, the performances of various four-leg inverters, from two-level inverters to three-level inverters, which are used as power converters for wave energy converters, are compared respectively. Since the four-leg converter has an unusual structure, the performance of each four-leg inverter was analyzed by applying the model predictive control that can easily and simply configure the controller. To verify the performance of each four-leg inverter, a comparison was performed under balanced load and unbalanced load conditions. Based on this, a suitable four-leg topology of the power converter for wave energy converters was confirmed.

Grid-connected PV battery systems for private homes are becoming increasingly popular in many countries, including Sweden. This study aimed to evaluate the techno-economic feasibility of such distributed, grid-connected PV battery systems for single homes at a Swedish holiday location. It was especially of interest to investigate the impact of demand charges, as they are frequently introduced by utilities in Sweden and are also common in popular winter sport regions. Grid-connected PV battery systems were sized and optimized based on their net present cost. Load patterns, incentives, demand tariff structures and electricity price variation were used to study the sensitivity of the obtained results. Grid-connected residential PV battery systems were found to be equally profitable compared to grid-connected PV systems without batteries when demand charges were applied. When the load profiles had peak loads throughout the whole year and the batteries were large enough sized to shave many... [more]

Through the transformation that the electrical sector has been passing by, improvements in asset management and the guarantee of sustainable and quality services have become essential aspects for power companies. Thus, the digitalization of energy utilities presents itself as an important and crucial process. A concept that involves a variety of innovative trends is the digital twin. It consists of a 3D virtual replica of existing physical objects and real-time monitoring of certain measures. By developing a digital twin in the electrical power grid, a virtual replica of the network is obtained providing network virtual maps, 3D asset models, dynamic and real-time data of grid assets, and IoT sensing. All these data can feed a platform where AI-based models and advanced field operation technologies and solutions will be applied. With a Network Digital Twin©development, applications involving on-field activities can be improved through augmented reality (AR) and virtual reality (VR) to... [more]

Sustainable energy systems rely on energy yield from renewable resources such as solar radiation and wind, which are typically not on-demand and need to be stored or immediately consumed. Solar irradiance is a highly stochastic phenomenon depending on fluctuating atmospheric conditions, in particular clouds and aerosols. The complexity of weather conditions in terms of many variable parameters and their inherent unpredictability limit the performance and accuracy of solar power forecasting models. As renewable power penetration in electricity grids increases due to the rapid increase in the installation of photovoltaics (PV) systems, the resulting challenges are amplified. A regional PV power prediction system is presented and evaluated by providing forecasts up to 72 h ahead with an hourly time resolution. The proposed approach is based on a local radiation forecast model developed by Blue Sky. In this paper, we propose a novel method of deriving forecast equations by using an irradia... [more]

High energy demand from the market due to the rapid increment of the human population worldwide has urged society to explore alternatives to replace non-renewable energy. Renewable diesel produced from biomass could be the next potential energy source for its high stability, long-term storage, and comparable performance with diesel fuels. In producing renewable diesel, the application of catalyst is essential, and the catalyst support is synthesized with the catalyst to enhance the reaction rate and catalytic properties. In this review, the type of catalyst support will be reviewed along with a brief introduction to biodiesel and renewable diesel production, especially focusing on zeolites as the catalyst support. The enhancement of catalyst support will be critically discussed to improve the catalytic performance of support in renewable diesel production and important aspects such as the stability and recyclability of the supported catalyst are included. The application of the support... [more]

Many industries apply traditional controllers to automate manual control. In recent years, artificial intelligence controllers applied with deep-learning techniques have been suggested as advanced controllers that can achieve goals from many industrial domains, such as humans. Deep reinforcement learning (DRL) is a powerful method for these controllers to learn how to achieve their specific operational goals. As DRL controllers learn through sampling from a target system, they can overcome the limitations of traditional controllers, such as proportional-integral-derivative (PID) controllers. In nuclear power plants (NPPs), automatic systems can manage components during full-power operation. In contrast, startup and shutdown operations are less automated and are typically performed by operators. This study suggests DRL-based and PID-based controllers for cold shutdown operations, which are a part of startup operations. By comparing the suggested controllers, this study aims to verify th... [more]

Oil tanker disasters have been a cause of major environmental disasters, with multi-generational impacts. One of the greatest hazards is damage to the propulsion system that causes the ship to turn sideways to a wave and lose stability, which in storm conditions usually leads to capsizing and sinking Despite the perceived consequences of maritime disasters in the current solutions for the propulsion of oil tankers, there are no legal or real solutions for independent emergency main propulsion in this type of ship. Stressing that the reliability of the propulsion system has a significant impact on the ship’s safety at sea, the authors presented a new solution in the form of a power take-off/power take-in (PTO/PTI) system. This is the emergency use of a shaft generator as the main electric motor, operating in parallel in a situation when the main engine (ME), (the main engine of the ship’s direct high-power propulsion system that is slow-speed) loses the operational capability to propel... [more]

An electrically excited synchronous machine (EESM) is a promising alternative to the permanent magnets synchronous machines being used in the automotive industry. However, the main disadvantage of the EESM with the conventional excitation system with brushes is the presence of slip rings on the shaft, which need regular maintenance. A promising alternative to the conventional excitation system of the EESM is a wireless power transfer (WPT) system. In this paper, we focused on WPT excitation system based on the rotary transformers. First, the model of the EESM in the d-q reference frame with vector control system has been built (based on the parameters of the real machine) and analyzed using MATLAB/Simulink software. Second, the influence of the rotary transformer design parameters on the dynamic performance of the EESM has been investigated. Finally, different topologies of the rotary transformers found in the literature have been analyzed, modeled and compared using an analytical and... [more]

A printed circuit heat exchanger (PCHE) is an efficient and compact heat exchanger that can work under high temperature and high pressure. For Z-shaped channel PCHEs, the corner structure could enhance heat transfer at the expense of increasing the flow resistance. In order to optimize the structural design and control the pressure loss caused by the corner, a three-dimensional numerical simulation using ICEM and Fluent is conducted to study the flow and heat transfer characteristics of carbon dioxide in a PCHE by inserting straight sections (offset distance 0.5−4 mm) or arc segments (radius of curvature 0.5−4 mm) at the zigzag corners of conventional Z-shaped channels. The overall performance of the PCHEs with different structures was compared based on the comprehensive evaluation factor. The results show that the pressure loss of the PCHE can be significantly reduced by inserting straight sections and arc segments at the zigzag corners, with the mass flow rate varying from 100 to 400... [more]

The vehicle-to-grid concept emerged very quickly after the integration of renewable energy resources because of their intermittency and to support the grid during on-peak periods, consequently preventing congestion and any subsequent grid instability. Renewable energies offer a large source of clean energy, but they are not controllable, as they depend on weather conditions. This problem is solved by adding energy storage elements, implementing a demand response through shiftable loads, and the vehicle-to-grid/vehicle-to-home technologies. Indeed, an electric vehicle is equipped with a high-capacity battery, which can be used to store a certain amount of energy and give it back again later when required to fulfill the electricity demand and prevent an energy shortage when the main-grid power is limited for security reasons. In this context, this paper presents a comparative study between two home microgrids, in one of which the concept of vehicle-to-home is integrated to provide a case... [more]

Industrial sectors are improving their energy efficiency and increasing their share of renewables for heating and cooling demands by using lower emission technologies. One specific approach to help achieve these targets is the integration of heat pumps (HPs) in industrial processes. However, due to the temporal variation of the heating and cooling requirements in non-continuous processes, the integration of HP is challenging. In this paper, a structured method for the design of HP integration is proposed. The method implements an engineer-centred workflow that extends the concept of the Indirect Source Sink Profile (ISSP) to HP integration. For this purpose, an adapted Grand Composite Curve is derived from the ISSP. This ensures correct HP integration across the pinch while maintaining the temperature lift of the HP small. The proposed workflow is applied to a demonstration case study and a case study from industry. In both cases, the resulting system with integrated HP enables the eli... [more]

Brown coal remains an important energy source in Europe, including countries such as Germany, Poland, the Czech Republic, and Greece. Open-pit mines disturb the environment in terms of air quality, hydrology, and chemical and biological transformations in rivers receiving mine waters. In the present study, we assessed the impact of mine waters from four brown coal open-pit mines on the contamination of river sediments. Chemical analysis included the quantification of 62 elements, including heavy metals (HMs) and rare earth elements (REEs). The contamination of sediments by HMs was evaluated using the contamination factor (CF), the pollution load index (PLI), and the Nemerow multi-factor index (PI). The potential toxic effects of HMs on aquatic organisms were assessed using the potential ecological risk index (PERI). Detailed analysis of chondrite-standardized concentrations of REEs was performed to describe the effects of mine water on their pattern in sediments. Cluster analysis (CA)... [more]

Hydraulic fracturing (HF) is currently the most widespread and effective method of oil production stimulation. The most commonly used fracturing fluid is crosslinked guar gels. However, when using these systems, problems such as clogging of the pore space, cracking, and proppant packing with the remains of the undestroyed polymer arise. Therefore, the efficiency of the hydraulic fracturing process decreases. In this work, compositions based on viscoelastic surfactants (VES) and synthetic polymers (SP) were considered as alternatives capable of minimizing these disadvantages. Most often, the possibility of using a composition as a fracturing fluid is evaluated using rotational viscometry. However, rotational viscometry is not capable of fully assessing the structural and mechanical properties of fracturing fluid. This leads to a reduced spread of systems based on VES and SP. This paper proposes an integrated approach to assessing the effectiveness of a water-based fracturing fluid. The... [more]

Zirconia-based composites with high thermochemical stability and electrochemical activity are the most promising solid electrolytes for manufacturing solid oxide fuel cells (SOFCs). In the present work, nanocrystalline composite powders of gadolinium-doped zirconia (GDZ: Gd2xZr2(1−x)O4−x) with various doping fractions (0.01 ≤ x ≤ 0.16) were synthesized by the Pechini method and applied for the fabrication of several electrolyte pellets to evaluate their physicochemical properties, sinterability, and conductivity. The X-ray diffraction (XRD) patterns and the thermogravimetry/differential thermal analysis (TGA/DTA) of the synthesized powders confirmed the successful formation of nanocrystalline GDZ in the tetragonal phase with complete substitution of gadolinium phase into the zirconia (ZrO2) lattice. The synthesized gadolinium zirconate powders were then shaped into pellet forms using the tape casting method, followed by sintering at 1300 °C (for 2.5 h). The microstructural analysis of... [more]

In this paper, the applicability of the Peukert equation and its generalizations were investigated for capacity evaluation of automotive-grade lithium-ion batteries. It is proved that the classical Peukert equation is applicable within the range of the discharge currents from 0.2Cn to 2Cn (Cn is the nominal battery capacity). As a rule, the operating currents of many automotive-grade lithium-ion batteries are exactly within this range of the discharge currents. That is why, successfully, the classical Peukert equation is used in many analytical models developed for these batteries. The generalized Peukert equation C = Cm/(1 + (i/i0)) is applicable within the discharge currents range from zero to approximately 10Cn. All kinds of operating discharge currents (including both very small ones and powerful short-term bursts) fall into this discharge currents range. The modified Peukert equation C = Cm(1 − i/i1)/((1 − i/i1) + (i/i0)) is applicable at any discharge currents. This equation take... [more]

Due to the increasing use of renewable energy sources, and to counter the effects of fossil fuels, renewable dispatchable hydro power can be used for balancing load and generation from intermittent sources (solar and wind). During higher percentage change in load acceptance or rejection in the intermittent grid, the operations of surge tanks are crucial in terms of water mass oscillation and water hammer pressure, and to avoid wear and tear in actuators and other equipment, such as hydro turbines. Surge tanks are broadly classified as open types, with access to open air, and closed types, with a closed volume of pressurized air. Closed surge tanks are considered to have a more flexible operation in terms of suppressing water mass oscillation and water hammer pressure. In this paper, a mechanistic model of an air cushion surge tank (ACST) for hydro power plants is developed based on the ordinary differential equations (ODEs) for mass and momentum balances. The developed mechanistic mode... [more]

A major challenge for gas-driven adsorption heat pumps is the production of compact, efficient, and cost-effective adsorption modules. We present the experimental data of a design based on sintered aluminum fiber heat exchangers, a technology currently under development. The adsorption module presented here is the result of the downsizing of a larger module. The downsized module has an adsorption heat exchanger that is 60% of the size of the larger-scale component, and an evaporator-condenser that is only 30% of the size of the larger-scale component. It is designed to fit the heating requirements of a wall-hung heat pump for a single-family home. For the first time, a comprehensive experimental study of the influence of half-cycle time, evaporator and adsorption temperature, and driving temperature on the efficiency and power of the module is presented. At temperature conditions relevant for the application of a gas-driven adsorption heat pump, i.e., evaporator temperature < 10 °C and... [more]

This paper investigates the presence of a causal relationship between energy poverty and income poverty in the EU Member States through a Panel Vector Autoregressive specification, and controlled with a set of explanatory variables collected from the Eurostat energy database and the OECD environment database for 2007−2018. Deepening the nexus between energy poverty and income poverty is a relevant issue for tailoring policies to tackle poverty and improve the well-being of citizens, supporting the policy makers in the allocation of planned funds provided by the Recovery plan, “Next Generation EU”. The results of the panel VAR model estimation and Dumitrescu and Hurlin test suggest that there will be no change in the long-run equilibrium when income poverty remains constant. Moreover, the reduction in energy poverty is expected to have a positive effect in terms of overall economic poverty reduction. Finally, there is evidence that substituting fossil fuels with renewables helps to redu... [more]

The acceptance of hybrid energy storage system (HESS) Electric vehicles (EVs) is increasing rapidly because they produce zero emissions and have a higher energy efficiency. Due to the nonlinear and strong coupling relationships between the sizing parameters of the HESS components and the control strategy parameters and EV’s performances, energy consumption rate, running range and HESS cost, how to design the HESS EVs for different preferences is a key problem. How to get the real time performances from the HESS EV is a difficulty. The multiobjective optimization for the HESS EV considering the real time performances and the HESS cost is a solution. A Li-ion battery (BT) semi-active HESS and optimal energy control strategy were proposed for an EV. The multiobjectives include energy consumption over 100 km, acceleration time from 0−100 km per hour, maximum speed, running range and HESS cost of the EV. According to the degrees of impact on the multiobjectives, the scaled factors of BT cap... [more]