Flux-switching permanent magnet (FSPM) machines have attracted wide attention in many rotating applications that require high-power density. In this research, we propose for the first time a novel six-phase FSPM generator with a stator featuring a V-shaped flux-focusing magnet arrangement. The design is targeted for low-speed wind power generation. To achieve the design objectives as a wind generator, the highly comprehensive structural parameters, including the number of rotor poles, split ratio, and rotor pole width, are designed and optimized using 2D finite-element analysis. From findings, the optimal stator/rotor pole combination is discovered to be 12/19 for the considered power and speed requirements. When compared to the initial structure, the optimized structure of the V-shaped FSPM generator is found to produce a significant improvement in EMF, cogging torque, electromagnetic torque, power, and efficiency. The power-generating performance of the proposed FSPM generator is fou... [more]

The flow ripple in an internal gear pump was measured by means of a new instantaneous high-pressure flowmeter. The flowmeter consists of two pressure sensors mounted on a piece of the straight steel pump delivery line, and a variable-diameter orifice was installed along such a line, downstream of the flowmeter, to generate a variable load. Three distinct configurations of the high-pressure flowmeter, characterized by a different distance between the pressure transducers, were analyzed. Furthermore, a comprehensive fluid dynamic 3D model of the pump and of its high-pressure delivery line was developed and validated in terms of both the delivery pressure and the flow ripple for different pump working conditions. For the three examined configurations of the flowmeter, the measured flowrate time histories matched the corresponding numerical distributions at the various operating points. Finally, the validated 3D model was applied to predict the incomplete filling working of the interteeth... [more]

Natural gas hydrate is easy to decompose and leak due to the changes in temperature and pressure during drilling, which causes safety accidents. Early monitoring of wellhead overflow is a practical and effective measure to prevent overflow blowouts and other accidents. Herein, a wellhead methane monitoring system for the open-circuit drilling of marine natural gas was designed. The system consisted of an overwater acoustic reception part and an underwater self-contained methane monitoring part, matching the construction environment of marine natural gas hydrate exploitation. Compared with the existing gas logging technology (measurement while drilling), the monitoring and early warning of wellhead methane content were realized at all stages of drilling, casing running, cementing, completion and fracturing in the process of natural gas hydrate exploitation. System communication and data acquisition tests were completed at different water depths through sea trials, which verified the eff... [more]

Due to the depletion of fossil fuels and the destruction wrought by global warming caused by the combustion of fossil fuels, the search for renewable energy sources has become a major global concern. This study aimed to assess the bio-oil production from teff husk via slow pyrolysis process. The pyrolysis of teff husk took place in a batch reactor at a temperature between 400 °C and 500 °C with a 120 min retention time. At 450 °C, the pyrolysis process produced 32.96 wt.% of optimum bio-oil yield and had a HHV of 25.32 MJ/kg. TGA, FTIR, and SEM-EDX were used to analyze the produced bio-oil to investigate its thermal decomposition, functional groups, and surface morphology with its elemental composition, respectively. Alcohols, aromatic, phenols, alkanes, esters, and ethers were the primary compounds of the bio-oil produced by the slow pyrolysis of teff husk. The HHV of the biochar ranged from 21.22 to 22.85 MJ/kg. As a result, teff husk can be used to make biofuel; however, further bio... [more]

It is of great significance to introduce the conception of a sharing economy into the electricity industry, which can promote the dispatch of multiple integrated energy systems. On the one hand, it is difficult to reveal the behaviors of complex players with multi-energy coupling through the traditional centralized optimization method of single electric energy. On the other hand, the uncertain fluctuations of renewable energy, such as wind power and photovoltaic, have posed great challenges to market transactions. First, the relationship and the functions of all stakeholders in the system are described in this paper, followed by the establishment of flexible resource models such as demand response and energy storage devices. On this basis, a low-carbon dispatching framework of multiple regional gas−electric integrated energy systems is then constructed under the guidance of cooperative game theory. The contribution indexes are established to measure the degree of energy sharing among t... [more]

Differential protection normally detects short circuits and ground faults in the windings of a power transformer and its terminals. Inter-turn faults refer to flashovers among the electrodes that arise only in a similar type of physical winding. Inter-turn faults can be examined when the adequate sum of turns is served as short-circuited. In electrical protection, it is difficult to detect inter-turn faults. An inter-turn fault of small magnitude is based on the limited number of turns that resultantly provide a large quantity of current. Due to this reason, protection that comes from the differential scenario possesses a higher degree of sensitivity without causing unwanted operations during external faults. In this paper, a protection-based stability method is proposed whereby external voltages are applied at the low-voltage (LV) side of the transformer while keeping the high-voltage (HV) side short-circuited. This was conducted using a three-phase power transformer (rating: 100 MVA,... [more]

Renewable energy development is growing fast and is expected to expand in the next decades in West Africa as a contribution to addressing the power demand and climate change mitigation. However, the future impacts of climate change on solar PV and the wind energy potential in the region are still unclear. This study investigates the expected future impacts of climate change on solar PV and wind energy potential over West Africa using an ensemble of three regional climate models (RCMs). Each RCM is driven by three global climate models (GCMs) from the new coordinated high-resolution output for regional evaluations (CORDEX-CORE) under the RCP8.5 scenario. Two projection periods were used: the near future (2021−2050) and the far future (2071−2100). For the model evaluation, reanalysis data from ERA5 and satellite-based climate data (SARAH-2) were used. The models and their ensemble mean (hereafter Mean) show acceptable performance for the simulations of the solar PV potential, the wind po... [more]

One of the bases of the European policy and energy strategy is the biomass and bioenergy obtained from it. It is estimated that by 2023, the annual demand for biomass will have increased from the current level of 7 EJ to 10 EJ. There are significant differences between estimates of the bioenergy potential due to the fact that the authors of publications do not use consistent methodology and assumptions. Forest biomass, agricultural residues, and energy crops are the three main sources of biomass for energy production. Energy crops are likely to become the most important source of biomass. Land use and its changes are a key issue in the sustainable production of bioenergy as the availability of biomass determines its potential for energy security. This article is a review of the latest publications on the bioenergy potential of the member-states of the European Union. The consumption of energy and its potential were presented, with a special focus on renewable sources, especially biomas... [more]

This article discusses magnetic vibrations in squirrel-cage induction motor stators and provides a mathematical description of the process of their excitation. A model of a 30 kW squirrel-cage induction motor was developed in finite element software. This model considers the motor geometry, material properties and stator winding. The electromagnetic and mechanical processes in the motor during the rotation of the rotor were considered. In the course of this study, currents of various harmonic compositions and amplitudes were applied to the motor windings, which caused magnetic noise, vibration and pulsations of the electromagnetic torque. Magnetic noises, vibrations and pulsations of the electromagnetic torque were investigated in the case of imbalance and harmonic distortions of the supply voltage.

A novel, integrated system is proposed for the cultivation and co-digestion of the invasive macrophyte water hyacinth (WH) with cow manure (CM) for the production of biogas for cooking in rural India. This study investigates the pre-treatment approaches and performs a techno-economic analysis of producing biogas in fixeddome digesters as a replacement for liquefied petroleum gas (LPG). Methodologies have been developed for the cultivation of WH collected from wild plants in the Indrayani River, Pune, India. Cultivation trials were performed in 350 litre tanks using water, which was nutrient fed with CM. Cultivation trials were performed over a 3 week period, and growth rates were determined by removing and weighing the biomass at regular time intervals. Cultivation results provided typical yields and growth rates of biomass, allowing predictions to be made for cultivation scaling. Samples of cultivated WH have been co-digested with CM at a 20:80 ratio in 200 L anaerobic digesters, allo... [more]

In any geological subsurface fluid injection, a viable top seal is required to contain the vertical movement of the injected fluid plume. However, seal integrity assessment is challenging because of the uncertainties possessed by various parameters. A probabilistic solution might be more appropriate when significant uncertainties are present. In this study, we evaluate Drake shale caprock structural reliability using a stochastic method. Drake shale is the primary top seal in the Aurora CO2 storage site, located in the Horda Platform area in the northern North Sea. Based on the lithological variations, Drake caprock shale is divided into two parts designated by upper and lower units. Six model scenarios from the upper and lower Drake units have been tested. The probabilistic structural failures of varying model scenarios are estimated using the First-Order Reliability Method (FORM). Drake Formation shale shows a considerably low probability of failure (~0) with a high reliability index... [more]

Vetiver grass (Chrysopogon zizanioides) is well-known for its contaminant phytoextraction potential and its capacity to reduce soil erosion, owing to its massive, dense root system. However, the shoots are not major contributors to either of these processes, and are either not utilized at all or they become part of the waste stream. It is well-recognized that lignocellulosic biomass can serve as a source of raw material to produce second-generation bioethanol. This study investigated the simultaneous saccharification and fermentation (SSF) of acid−alkali pretreated vetiver (VG) shoots by Saccharomyces cerevisiae. Vetiver shoots were obtained from three sources: (1) shoots from VG grown in clean potting soil, (2) shoots from VG used for antibiotics phytoextraction from a constructed wetland setup, and (3) shoots from VG used for lead phytoextraction during soil remediation. Bioethanol yield from the shoots from clean soil was the highest (19.58 g/L), followed by the one used for lead ph... [more]

The growing production of plastic waste and improper dumping after use has become a worldwide challenge. This waste is a substantial source of petroleum and can be effectively converted into pyrolytic oil and other useful products. A statistical prediction of the rate constants is essential for optimizing pyrolysis process parameters, such as activation energy (Ea), frequency factor (Ao), temperature (T), and kinetic rate constants (k). In this research, we utilized Box−Behnken using RSM with Design Expert software to predict statistical rate constants at 500 °C and 550 °C. The efficiency of the predicted rate constants was investigated and compared to the findings of experimental rate constants extracted from the literature. At 500 °C, the estimated rate constants did not reveal a significant rise in the oil output since these constants promoted high gas yield. Compared to the experimental rate constants, statistically predicted rate constants at 550 °C demonstrated substantially high... [more]

With the growing need for decarbonization, the future gas demand will decrease and the necessity of a gas distribution network is at stake. A remaining industrial gas demand on the distribution network level could lead to industry becoming the main gas consumer supplied by the gas distribution network, leading to the question: can industry keep the gas distribution network alive? To answer this research question, a three-stage analysis was conducted, starting from a rough estimate of average gas demand per production site and then increasing the level of detail. This paper shows that about one third of the German industry sites investigated are currently supplied by the gas distribution network. While the steel industry offers new opportunities, the food and tobacco industry alone cannot sustain the gas distribution network by itself.

One of the ways to minimize anthropogenic emissions from coal combustion is to replace conventional schemes used for the introduction of coal dust into the furnaces of power plants through the injection of water-containing fuels. In this research, the three most promising schemes for fuel combustion were implemented: (i) the simultaneous introduction of coal particles and water droplets into the combustion chamber; (ii) steam injection into the fuel particle combustion zone; and (iii) the introduction of coal−water slurries into the furnace. Three methods of supplying water to the combustion zone were evaluated using the multi-criteria decision-making technique. Experimental research was conducted to record a range of process characteristics: the time of the gas-phase and heterogeneous ignition, the time of complete combustion, minimum ignition temperatures, maximum combustion temperatures, the completeness of the fuel burnout and the concentrations of the main gaseous emissions. It ha... [more]

To integrate large shares of renewable energy sources in electric grids, large-scale and long-duration (4−8+ h) electric energy storage technologies must be used. A promising storage technology of this kind is pumped thermal electricity storage based on Brayton cycles. The paper’s novel contribution is in the techno-economic comparison of two alternative configurations of such storage technology. Liquid-based and solid-based pumped thermal electricity storage were studied and compared from the techno-economic point of view. The cost impacts of the operating fluid (air, nitrogen, and argon), power rating, and nominal capacity was assessed. Air was the most suitable operating fluid for both technologies, simplifying the plant management and achieving cost reductions between 1% and 7% compared to argon, according to the considered configuration. Despite a more complex layout and expensive thermal storage materials, liquid-based systems resulted in being the cheapest, especially for large... [more]

The topic of reducing exhaust gas emissions from internal combustion engines in the areas of port and coastal waters is in line with the assumptions of the climate policy. The publication presents a proposal to reduce the energy associated with the movement of port vessels through the use of a specific pattern (shape and size) of their movement. In addition to controlling the formation of tugboats, the authors propose the use of a multi-agent system offering elements of autonomous control of the vessels, which adjusts the parameters of the formation depending on the tasks performed. The results of tests for four tugboats with a hull length of 32 m and a maximum speed of 13 knots, moving in formations of eight different configurations, were analyzed. Studies conducted on the basis of a simulated exit and return to port scenario at a distance of 11.4 nm showed the possibility of reducing energy consumption required for movement by 5.8% to even 57.6% for tugboats moving one after another,... [more]

Cork is a versatile natural material. It can be used as an insulator in construction, among many other applications. For good forest management of cork oaks, forest owners need to calculate the volume of cork periodically. This will allow them to choose the right time to harvest the cork. The traditional method is laborious and time consuming. The present work aims to automate the process of calculating the trunk area of a cork oak from which cork is extracted. Through this calculation, it will be possible to estimate the volume of cork produced before the stripping process. A deep neural network, Mask R-CNN, and a machine learning algorithm are used. A dataset of images of cork oaks was created, where targets of known dimensions were fixed on the trunks. The Mask R-CNN was trained to recognize targets cork regions, and so the area of cork was estimated based on the target dimensions. Preliminary results show that the model presents a good performance in the recognition of targets and... [more]

The high penetration of photovoltaic solar generation and electric vehicles in developing countries and with vertically integrated electricity markets with restrictive regulatory policies enhance demand management and the participation of prosumers in optimizing their resources. In this sense, the research presents a demand management methodology based on the prosumer model for recharging electric vehicles through optimization based on linear programming to minimize recharging costs, considering the stochasticity of the solar radiation variables, vehicular mobility patterns, consumer preferences, and optimal location of charging stations through surveys and predictive tools such as PVsyst and GAMS, in such a way that the energy demand for recharging electric vehicles is met. This way, the methodology reduces power demand peaks and mitigates the economic and technical impact on distribution networks. This case study has been modelled with real information from electric vehicles, distrib... [more]

Securing net-zero targets by employing sustainable materials for the built environment is highly desirable, and this can be achieved by retrofitting existing non-smart windows with thermoelectric (TE) glazing, providing improved thermal performance along with green electricity production. It is reported that TE glazing could produce ~4000 kWh of power per year in a cold climate with a temperature differential of ~22 °C. This feature of TE materials drives their emplacement as an alternative to existing glazing materials and could lead to the identification of optimum solutions for smart window development. However, few attempts have been made to employ TE materials in glazing. Therefore, in this brief review, we discuss, for the first time, the efforts made to employ TE in glazing, identify their drawbacks, and discuss potential solutions. Furthermore, the working principle, suitable materials, and methods for developing TE glazing are discussed. In addition, this article introduces a... [more]

The increasingly widespread use of electric vehicles requires proper planning of the charging infrastructure. In addition to the correct identification of the optimal positions, this concerns the accurate sizing of the charging station with respect to energy needs and the management of power flows. In particular, if we consider the presence of a renewable energy source and a storage system, we can identify strategies to maximize the use of renewable energy, minimizing the purchase costs from the grid. This study uses real charging data for some public stations, which include “normal” chargers (3 kW and 7 kW) and “quick” ones (43 kW and 55 kW), for the optimal sizing of a photovoltaic system with stationary storage. Battery degradation due to use is included in the evaluation of the overall running costs of the station. In this study, two different cost models for battery degradation and their influence on energy flow management are compared, along with their impact on battery life.

Geopolitical developments since February 2022 and the numerous debates on climate change such as the COP27 are pushing for a greater acceleration in decarbonising the energy sector. The use of geothermal energy for thermal energy production and storage in district heating and cooling (DHC) grids may also be a key element in overcoming short-term energy peaks. This work aimed at evaluating the efficiency and performance of one of the most promising underground thermal energy storage systems, which uses boreholes to store heat or cold (BTES). Numerical simulations allowed for understanding how these technologies can be used as backup systems, or when the energy demand overcomes that supplied by conventional heating systems. The knowledge on how to exploit this energy source shows that a continuous heat extraction from the storage volume can meet both the base and peak load requests for several users, with cumulative energy amounting to 476,000 kWh over the first month. This study proved... [more]

Clean electricity is generated by the anaerobic digestion of biomass waste. The environmental impacts of various biomass waste feedstocks vary, while co-digestion has been reported to improve anaerobic digestion performance. A consequential life-cycle assessment (LCA) and techno-economic analysis (TEA) are carried out for cow manure waste management for a cow farm. Three scenarios are considered in this study: (S1) mono-digestion of cow manure, (S2) co-digestion of cow manure and maize silage, and (S3) co-digestion of cow manure with cow feed waste, sewage sludge, and returned dairy products. The LCA aims to quantify the environmental impact of each MWh of electricity generated, assuming the plant is located in Malaysia, using OpenLCA software. The TEA economic parameters are quantified and compared between the three scenarios. Net present value (NPV), Internal Return Rate (IRR), and Return of Investment (ROI) are examined. Among the three scenarios, S2 with maize cultivation has a hig... [more]

This paper presents experimental findings on heat and mass transfer, phase transitions, and chemical reactions during the interaction of CO2 hydrate in powder granules and tablets with burning liquid fuels and oil. The experiments involved CO2 hydrate tablets and spheres made of pressed granules. The fire containment and suppression times were established experimentally. Using the gas analysis data, we studied the effects of the mitigation of anthropogenic emissions from the combustion of liquids and their suppression by gas hydrates. We also compared the performance of water aerosol, foaming agent emulsion, snow, ice, and CO2 hydrate samples as laboratory-scale fire suppressants. The paper further describes the numerical modeling of the CO2 hydrate dissociation during liquid fuel combustion. The rapid carbon dioxide release is shown to prevent the oxidizer from the combustion zone. The suppression of a flame using powder with a granule size of 3 mm requires 20-times less carbon dioxid... [more]

The thermal regulation of a silicon photovoltaic (PV) solar system is essential as the module surface temperature beyond 25 °C deteriorates its Power Conversion Efficiency (PCE). The intensity of solar radiation seems to have a crucial impact on the PCE of a PV solar system. The present study aims to assess the effect of solar radiation variations on the PCEs of PV modules integrated with and without passive cooling systems. The used passive cooling systems are (a) multi-pipe copper frame filled with Phase Change Material (PCM) and (b) multi-pipe copper frame filled with ZnO-doped PCM. The tests were conducted at the University of Jeddah in the month of March at various local times. The results show that the ambient and module surface temperatures are directly dominated by solar radiations. The conventional PV solar system presents a higher module surface temperature as compared to that of a PV system integrated with ZnO/PCM. The enhanced module surface temperature decreases the open c... [more]