For the stable supply of oil and gas resources, industry is pushing for various attempts and technology development to produce not only existing land fields but also deep-sea, where production is difficult. The development of flow assurance technology is necessary because hydrate is aggregated in the pipeline and prevent stable production. This study established a system that enables hydrate diagnosis in the gas pipeline from a flow assurance perspective. Learning data were generated using an OLGA simulator, and temperature, pressure, and hydrate volume at each time step were generated. Stacked auto-encoder (SAE) was used as the AI model after analyzing training loss. Hyper-parameter matching and structure optimization were carried out using the greedy layer-wise technique. Through time-series forecast, we determined that AI diagnostic model enables depiction of the growth of hydrate volume. In addition, the average R-square for the maximum hydrate volume was 97%, and that for the form... [more]

Flexible AC Transmission Systems (FACTS) are essential devices used for the efficient performance of modern power systems and many developing countries lack these devices. Due to the non-existence of these advanced technologies, the national grid remains weak and vulnerable to power stability issues that can jeopardize system stability. This study proposes novel research to solve issues of an evolving national grid through the installation of FACTS devices. FACTS devices play a crucial role in minimizing active power losses while managing reactive power flows to keep the voltages within their respective limits. Due to the high costs of FACTS, optimization must be done to discover optimal locations as well as ratings of these devices. However, due to the nonlinearity, it is a challenging task to find the optimal locations and appropriate sizes of these devices. Shunt VARs Compensators (SVCs) and Thyristor-Controlled Series Compensators (TCSCs) are the two FACTS devices considered for th... [more]

To improve the performance of electrically assisted turbochargers (EATs), the influences of the hub profile and the casing profile on EAT performance were numerically studied by controlling the upper and lower endwall profiles. An artificial neural network and a genetic algorithm were used to optimize the endwall profile, considering the total pressure ratio and the isentropic efficiency at the peak efficiency point. Different performances of the prototype EAT and the optimized EAT under variable clearance sizes were discussed. The endwall profile affects an EAT by making the main flow structure in the endwall area decelerate and then accelerate due to the expansion and contraction of the meridional surface, which weakens the secondary leakage flow of the prototype EAT and changes the momentum ratio of the clearance leakage flow and the separation flow in the suction surface corner area. Because the tip region flow has a more significant influence on EAT performance, the optimal casing... [more]

In the process industry, a large amount of low-grade waste heat is discharged into the environment. Furthermore, district heating and cooling systems require considerable low-grade energy. The integration of the two systems has great significance for energy saving. Because the energy demand of consumers varies in periods, the design and operation of an industrial waste heat recovery system need to match with the fluctuations of district energy demand. However, the impact of the periodic changes on the integration schemes are not considered enough in existing research. In this study, a framework method for solving above problem is proposed. Industrial waste heat was integrated with a district heating and cooling system through a heat recovery loop. A three-step mathematical programming method was used in design and operation optimization for multiperiod integration. A case study was conducted, and the results show that the multiperiod optimization method can bring significant benefits t... [more]

This paper analyzes a novel, cost-effective planar waveguide solar concentrator design that is inspired by cellular hexagonal structures in nature with the benefits of facile installation and low operation and maintenance cost. A coupled thermal and optical analysis of solar irradiation through an ideal hexagonal waveguide concentrator integrated with a linear receiver is presented, along with a cost analysis methodology, to establish the upper limit of performance. The techno-economic model, coupled with numerical optimization, is used to determine designs that maximized power density and minimized the cost of heat in the temperature range of 100−250 °C, which constitutes more than half of the industrial process heat demand. Depending on the incident solar irradiation and the application temperature, the cost of heat for the optimal design configuration ranged between 0.1−0.27 $/W and 0.075−0.18 $/W for waveguide made of ZK7 glass and polycarbonate, respectively. A techno-economic ana... [more]

Five major operations for the conversion of lignocellulosic biomasses into bioethanol are pre-treatment, detoxification, hydrolysis, fermentation, and distillation. The fermentation process is a significant biological step to transform lignocellulose into biofuel. The interactions of biochemical networks and their uncertainty and nonlinearity that occur during fermentation processes are major problems for experts developing accurate bioprocess models. In this study, mechanical processing and pre-treatment on the palm trunk were done before fermentation. Analysis was performed on the fresh palm sap and the fermented sap to determine the composition. The analysis for total sugar content was done using high-performance liquid chromatography (HPLC) and the percentage of alcohols by volume was determined using gas chromatography (GC). A model was also developed for the fermentation process based on the Adaptive-Network-Fuzzy Inference System (ANFIS) combined with particle swarm optimization... [more]

This paper investigates bilevel optimization models for demand response management, and highlights the often overlooked consequences of a common modeling assumption in the field. That is, the overwhelming majority of existing research deals with the so-called optimistic variant of the problem where, in case of multiple optimal consumption schedules for a consumer (follower), the consumer chooses an optimal schedule that is the most favorable for the electricity retailer (leader). However, this assumption is usually illegitimate in practice; as a result, consumers may easily deviate from their expected behavior during realization, and the retailer suffers significant losses. One way out is to solve the pessimistic variant instead, where the retailer prepares for the least favorable optimal responses from the consumers. The main contribution of the paper is an exact procedure for solving the pessimistic variant of the problem. First, key properties of optimal solutions are formally prove... [more]

The aim of this scientific research is to experimentally determine the exergy losses of a ground heat pump and further optimization for more efficient use of operating modes and improvement of individual structural elements. In addition, it is proposed to use photovoltaic panels as a backup power source for the experimental installation under study. The exergetic losses are calculated, not only for the ground heat pump itself, with R407C refrigerant. The research methodology consists in a comprehensive assessment of exergetic flows, their optimization using new methods of approximation of piecewise linear functions, and the development of prerequisites for the use of anergy as one of the components of a new type of analysis of the efficiency of low-potential energy sources. As a result of processing the experimental data, the values of Coefficient of performance (COP) 4.136, exergetic temperature for the lower heat source 0.0253 and for the upper heat source 0.155, exergetic efficiency... [more]

This paper proposes a methodology aiming at determining the most influent working variables and geometrical parameters over the pressure drop and heat transfer during the condensation process of several refrigerant gases using heat exchangers with pipes mini channels technology. A multi-criteria decision making (MCDM) methodology was used; this MCDM includes a mathematical method called SIMUS (Sequential Interactive Modelling for Urban Systems) that was applied to the results of 2543 tests obtained by using a designed refrigeration rig in which five different refrigerants (R32, R134a, R290, R410A and R1234yf) and two different tube geometries were tested. This methodology allows us to reduce the computational cost compared to the use of neural networks or other model development systems. This research shows six variables out of 39 that better define simultaneously the minimum pressure drop, as well as the maximum heat transfer, saturation pressure fluid entering the condenser being the... [more]

Accurate localization of partial discharge in GIS equipment remains a key focus of daily maintenance for substations, which can be achieved through advanced detection and location techniques, as well as regular maintenance and testing of the equipment. However, there is currently an issue with low accuracy in the localization algorithm. Aiming at the problems of low precision and local optimization of the swarm intelligence algorithm in partial discharge localization system of GIS equipment, this paper proposes a 3D localization algorithm based on a time difference of arrival (TDOA) model of the improved artificial fish swarm algorithm (IAFSA). By introducing the investigation behaviour of the artificial bee colony(ABC) algorithm into the artificial fish swarms algorithm (AFSA), this algorithm is more efficient to jump out of the local extremum, enhance the optimization performance, improve the global search ability and overcome the premature convergence. Furthermore, more precise posi... [more]

The current geopolitical landscape of the European Union has made it clear that the energy sector must be a top priority in EU policy, especially in light of the sudden escalation of Russian−Ukrainian conflicts. Energy efficiency has been used as the first tool of EU policy to tackle energy and climate crises, given the issues surrounding energy vulnerability and the need to limit gas emissions that contribute to climate change. The white certificate mechanism in Italy has played a pivotal role in encouraging measures to achieve the country’s energy-saving goals. Given the high energy requirements of Wastewater Treatment Plants (WWTPs), especially for aeration in the biological section, this paper examines the replacement of the air distribution system for a large WWTP as a viable intervention. In order to provide economic perspective for the plant, both the discounted Payback Period (dPBP) and the Net Present Value (NPV) were calculated for the investment. When viewed through an econo... [more]

In this work, the solar-thermal-chemical integrated design for a methane dry reforming reactor with cavity-type solar absorption was numerically performed. Combined with a multiphysical reactor model, the gradient optimization algorithm was used to find optimal radiation flux distribution with fixed total incident solar energy for maximizing overall hydrogen yield, defined as the ratio of molar flow of exported hydrogen to imported methane, which can be applied for guiding the optical property design of solar adsorption surface. The comprehensive performances of the reactor under the conditions of original solar flux and optimal solar flux were analyzed and compared. The results show that for the inlet volume flow rate of 8−14 L·min−1, the hydrogen production rate was increased by up to 5.10%, the energy storage efficiency was increased by up to 5.55%, and the methane conversion rate was increased by up to 6.01%. Finally, the local absorptivities of the solar-absorptive coating on the... [more]

Coiled tubing (CT) is used as a velocity string to transport high-velocity gas in drainage gas recovery technology. Sand particles flowing at high speed can cause serious erosion of the pipe wall. Long-term erosion wear leads to the degradation of the string strength and can even cause local perforation. In order to study the erosion wear problem of CT, a gas−solid erosion experimental device was established for a full-size pipe with different radii of curvature. A 3D laser confocal technique was used to examine and characterize the microscopic erosion morphology of the inner wall of the CT. The CFD erosion model was selected based on the erosion test data of the inner wall of the CT, and the erosion results of the Finnie model show minimal error and good agreement compared with other models. The average value of the error of the maximum erosion rate at different radii of curvature is 8.3%. The effect of the radius of curvature, gas velocity and solid particle size on the maximum erosi... [more]

Small modular reactors (SMRs) are gaining interest as a potential solution for cost-effective, carbon-neutral district heat (DH) production. The low pressures and temperatures permit much lighter and cheaper designs than in power plants, and efficiency is high as all heat generated can be sold to customers. In this work, the optimization of the primary heat exchangers in a natural-circulation 50-MW heating reactor concept was carried out to obtain an initial feasibility estimate for the concept for both baseload and load-following operation, as well as to obtain information on the characteristics of an optimized design. Studies on small natural circulation heat-only SMRs and the impact of heat exchanger design on the overall dimensions and economics have not been published before. Although a detailed heat exchanger cost model was used, the results should be considered tentative initial estimates, as much of the cost impact from the heat exchanger design comes from the effect the design... [more]

Structure parameters have an important influence on the refrigeration performance of pulse tube refrigerators. In this paper, a method combining the Kriging metamodel and Non-Dominated Sorting Genetic Algorithm II (NSGA II) is proposed to optimize the structure of regenerators and pulse tubes to obtain better cooling capacity. Firstly, the Kriging metamodel of the original pulse tube refrigerator CFD model is established to improve the iterative solution efficiency. On this basis, NSGA II was applied to the optimization iteration process to obtain the optimal and worst Pareto front solutions for cooling performance, the heat and mass transfer characteristics of which were further analyzed comparatively to reveal the influence mechanism of the structural parameters. The results show that the Kriging metamodel presents a prediction error of about 2.5%. A 31.24% drop in the minimum cooling temperature and a 31.7% increase in cooling capacity at 120 K are achieved after optimization, and t... [more]

This paper proposes an optimal ensemble method for one-day-ahead hourly wind power forecasting. The ensemble forecasting method is the most common method of meteorological forecasting. Several different forecasting models are combined to increase forecasting accuracy. The proposed optimal ensemble method has three stages. The first stage uses the k-means method to classify wind power generation data into five distinct categories. In the second stage, five single prediction models, including a K-nearest neighbors (KNN) model, a recurrent neural network (RNN) model, a long short-term memory (LSTM) model, a support vector regression (SVR) model, and a random forest regression (RFR) model, are used to determine five categories of wind power data to generate a preliminary forecast. The final stage uses an optimal ensemble forecasting method for one-day-ahead hourly forecasting. This stage uses swarm-based intelligence (SBI) algorithms, including the particle swarm optimization (PSO), the sa... [more]

In this paper, determination of optimized regenerative braking-torque function and application in energy efficient driving strategies is presented. The study investigates a lightweight electric vehicle developed for the Shell Eco-Marathon. The measurement-based simulation model was implemented in the MATLAB/Simulink environment and used to establish the optimization. The optimization of braking-torque function was performed to maximize the recuperated energy. The determined braking-torque function was applied in a driving strategy optimization framework. The extended driving strategy optimization model is suitable for energy consumption minimization in a designated track. The driving strategy optimization was created for the TT Circuit Assen, where the 2022 Shell Eco-Marathon competition was hosted. The extended optimization resulted in a 2.97% improvement in energy consumption when compared to the result previously achieved, which shows the feasibility of the proposed methodology and... [more]

In this paper, we propose an optimization model that considers two pathways for injecting renewable content into natural gas pipeline networks. The pathways include (1) power-to-hydrogen or PtH, where off-peak electricity is converted to hydrogen via electrolysis, and (2) power-to-methane, or PtM, where carbon dioxide from different source locations is converted into renewable methane (also known as synthetic natural gas, SNG). The above pathways result in green hydrogen and methane, which can be injected into an existing natural gas pipeline network. Based on these pathways, a multi-period network optimization model that integrates the design and operation of hydrogen from PtH and renewable methane is proposed. The multi-period model is a mixed-integer non-linear programming (MINLP) model that determines (1) the optimal concentration of hydrogen and carbon dioxide in the natural gas pipelines, (2) the optimal location of PtH and carbon dioxide units, while minimizing the overall syste... [more]

In the context of energy transformation, the importance of energy storage devices in regional integrated energy systems (RIESs) is becoming increasingly prominent. To explore the impact of energy storage devices on the design and operation of RIESs, this paper first establishes a bi-level dynamic optimization model with the total system cost as the optimization objective. The optimization model is used to optimize the design of three RIESs with different energy storage devices, including System 1 without an energy storage device, System 2 with a thermal energy storage (TES) device, and System 3 with TES and electrical energy storage (EES) devices. According to the design and operation results, the impact of energy storage devices on the operational performance of RIESs is analyzed. The results show that under the design conditions, energy storage devices can significantly increase the capacity of the combined heating and power units and absorption chillers in System 2 and System 3 and... [more]

The free market forces energy-intensive industrial enterprises to continuously compete. A possible competitive advantage for such enterprises is reducing the finished products cost. This may be achieved by reducing the share of energy in this cost, including by rationalizing the use of energy resources. This study develops a system for the automated analysis and calculation of feasible boiler unit loads, defined according to the criterion of the minimum cost of live steam in a separate steam plant pipeline. The calculations consider the balance limit on the steam, the boiler unit’s wear and tear, performance specifications, and economic indicators of fuel consumption in the calculation. The software also defines the optimal fuel mix composition when forecasting the operating modes of the power plant boiler units in real-time mode. The calculation algorithm is based on the dynamic programming technique combined with the sequential equivalenting method, which ensures the convergence of c... [more]

This study presents an optimal insertion model for battery storage systems in the nodes of an electrical transmission network. The proposed model is developed through mixed integer linear programming applied to the calculation of DC power flows, considering restrictions given by the characteristics of the network and by the parameters of the generation units. The proposal’s main objective is to reduce the costs of operation and non-supplied energy produced, due to needing to meet the demand fully or partially. As a case study to evaluate the proposed methodology, the IEEE 24-bar test system is used. In this base case, electrical generators that depend on different primary energy resources are modeled: hydraulic, thermal, photovoltaic, and wind, in addition to potential electrical energy storage systems. These storage systems are assigned as possible analysis scenarios through the proposed optimization technique. The study is carried out in a time horizon of 24 h per day, according to a... [more]

Monitoring the temperature of a semiconductor component allows for the prediction of potential failures, optimization of the selected cooling system, and extension of the useful life of the semiconductor component. There are many methods of measuring the crystal temperature of the semiconductor element referred to as a die. The resolution and accuracy of the measurements depend on the chosen method. This paper describes known methods for measuring and imaging the temperature distribution on the die surface of a semiconductor device. Relationships are also described that allow one to determine the die temperature on the basis of the case temperature. Current trends and directions of development for die temperature measurement methods are indicated.

As large-scale wind turbines are connected to the grid, modeling studies of wind farms are essential to the power system dynamic research. Due to the large number of wind turbines in the wind farm, detailed modeling of each wind turbine leads to high model complexity and low simulation efficiency. An equivalent modeling method for the wind farm is needed to reduce the complexity. For wind farms with widely used doubly-fed induction generators (DFIGs), the existing equivalent studies mainly focus on such continuous control parts as electrical control. These methods are unsuitable for the low voltage ride through (LVRT) part which is discontinuous due to switching control. Based on particle swarm optimization (PSO) and density-based spatial clustering of applications (DBSCAN), this paper proposes an equivalent method for LVRT characteristics of wind farms. Firstly, the multi-turbine equivalent model of the wind farm is established. Each wind turbine in the model represents a cluster of w... [more]

In order to reduce the comprehensive power cost of the independent microgrid and to improve environmental protection and power supply reliability, a two-layer power capacity optimization model of a microgrid with electric vehicles (EVs) was established that considered uncertainty and demand response. Based on the load and energy storage characteristics of electric vehicles, the classification of electric vehicles was proposed, and their mathematical models were established. The idea of robust optimization was adopted to construct the uncertain scenario set. Considering the incentive demand response, a two-layer power capacity optimization model of a microgrid was constructed. The improved pelican optimization algorithm (IPOA) was proposed as the two-layer model. In view of the slow convergence rate of the pelican optimization algorithm (POA) and its tendency to fall into the local optimum, methods such as elite reverse learning were proposed to generate the initial population, set dist... [more]

This article studies a recently proposed dc-dc converter and its optimization in terms of capacitors selection through the Particle Swarm Optimization (PSO) algorithm. The converter under study is the so-called Low Energy Storage Quadratic Boost Converter (LES-QBC), a quadratic type of converter that offers a smaller Output Voltage Ripple (OVR) compared to the traditional quadratic boost topology with capacitors of the same characteristics. This study presents a way to select the capacitors for minimizing the OVR while achieving a constraint of a maximum stored energy in capacitors. The capacitor’s stored energy is given as a design specification. The results are compared against the traditional quadratic boost converter and the LES-QBC without optimization (equal capacitance in capacitors). The optimization algorithm used was the so-called Particle Swarm Optimization (PSO). The experimental results demonstrate the effectiveness of the proposition. For the design exercise used for the... [more]