This paper presents results of research on unevenness of cylinder heating in a furnace for thermo-chemical treatment. Experimental research was conducted with respect to nitriding. Various heating speeds and settings of the fan operation in the furnace were considered. Boundary conditions were calculated in the form of temperature and the heat transfer coefficient (HTC) on the cylinder boundary in four planes along the cylinder length. Calculations were performed with the use of the inverse problem for non-linear and unsteady heat conduction equations. Boundary conditions from individual planes were compared with the mean value of them all. The variability of the calculated boundary conditions (temperature and HTC) along the cylinder length was investigated based on values of the absolute and relative differences for temperature and HTC. Estimates: mean value, mean value from the absolute value and the maximum values for the absolute and the relative differences of temperature and HTC... [more]

Static eccentricity (SE) is frequently generated by manufacturing processes. As the nonuniformity of the air-gap length is caused by the SE, the torque ripple and cogging torque increase in the motor. This study analyzes the distorted back electromotive force (EMF) and cogging torque due to SE. Further, a motor design considering SE is performed for stable back EMF and low cogging torque. First, the SE was diagnosed and analyzed using the back EMF and cogging torque measured from the test results of the base model. In addition, the rotor position was calculated using the unbalanced back EMF due to the SE. The calculated rotor position is used when analyzing phenomena due to SE and applied to robust design. Subsequently, robust design optimization was performed to improve the unbalanced back EMF and cogging torque due to SE. Using finite element analysis (FEA) considering SE, the shape of the stator was designed based on the base model. The estimated rotor position from the base model w... [more]

Offshore wind power plants are becoming a realistic option for the renewable production of electricity. As an improvement tool to the profitability of OWFs, this work presents the first complete non-genetic (and non-binary) evolutionary algorithm to optimize the location, size and layout of a parallelogram-shaped offshore wind farm, as the arrangement that is becoming an standard for offshore wind farms. It has been tested in the HRI site. Most relevant economic data influencing the investment profitability have been taken into account. In addition, the paper introduces a new approach to offshore wind farm optimization based on a continuous behaviour of varying wind conditions, which allows a more realistic estimation of the energy produced. The proposed optimization approach has been tested based on the available information from HRI. Obtained solutions present similar values to the actual offshore wind farm in terms of investment and annual energy produced, but differs with respect t... [more]

Optimal design of regional integrated energy systems (RIES) offers great potential for better managing energy sources, lower costs and reducing environmental impact. To capture the transition process from fossil fuel to renewable energy, a flexible RIES, including the traditional energy system (TES) based on the coal and biomass based distributed energy system (BDES), was designed to meet a regional multiple energy demand. In this paper, we analyze multiple scenarios based on a new rural community in Dalian (China) to capture the relationship among the energy supply cost, increased share of biomass, system configuration transformation, and renewable subsidy according to regional CO2 emission abatement control targets. A mixed integer linear programming (MILP) model was developed to find the optimal solutions. The results indicated that a 40.58% increase in the share of biomass in the RIES was the most cost-effective way as compared to the separate TES and BDES. Based on the RIES with m... [more]

Small-spacing twin-well (SSTW) salt caverns have an extensive application prospect in thin or bedded rock salt formations due to their good performance, while they are rarely used in ultra-deep formations. The target strata depth of Pingdingshan salt mine is over 1700 m, and it is planned to apply an SSTW cavern to construct the underground gas storage (UGS). A 3D geomechanical model considering the viscoelastic plasticity of the rock mass is introduced into Flac3D to numerically study the influence of internal gas pressure, cavern upper shape and well spacing on the stability of an SSTW salt cavern for Pingdingshan UGS. A set of assessment indices is summarized for the stability of gas storage. The results show that the minimum internal gas pressure is no less than 14 MPa, and the cavern should not be operated under constant low gas pressure for a long time. The cavern with an upper height of 70 m is recommended for Pingdingshan gas storage based on the safety evaluation and maximum v... [more]

Soaring energy demand and the establishment of various trends in the energy market have paved the way for developing demand-side management (DSM) from the consumer side. This paper proposes a reinforced DSM (RDSM) approach that uses an enhanced binary gray wolf optimization algorithm (EBGWO) that benefits the consumer premises with load scheduling, and peak demand reduction. To date, DSM research has been carried out for residential, commercial and industrial loads, whereas DSM approaches for educational loads have been less studied. The institution load also consumes much utility energy during peak hours, making institutional consumers pay a high amount of cost for energy consumption during peak hours. The proposed objective is to reduce the total electricity cost and to improve the operating efficiency of the entire load profile at an educational institution. The proposed architecture integrates the solar PV (SPV) generation that supplies the user-comfort loads during peak operating... [more]

The paper provides a methodology for the optimal control of heating, ventilation, and air conditioning (HVAC) systems used in public buildings, with the purpose of obtaining high comfort and safety standards along with energy efficiency. The combination of the two concurrent objectives of minimizing energy use and guaranteeing high standards of occupant comfort is obtained by means of multi-objective optimization, in which a comfort model is combined along with a dynamic energy model of the building. The use of dynamic setpoints for the HVAC and the inclusion of comfort indicators represent a step forward, compared to the current design and operation procedures suggested by technical standards. The utilization of the proposed methodology is tested with reference to a case study, represented by an academic building used by the University of Pisa for educational purposes, whose extensive and variable occupancy can help to emphasize the importance of comfort in the operation of HVAC syste... [more]

Clean and renewable energy is developing to realize the sustainable utilization of energy and the harmonious development of the economy and society. Microgrids are a key technique for applying clean and renewable energy. The operation optimization of microgrids has become an important research field. This paper reviews the developments in the operation optimization of microgrids. We first summarize the system structure and provide a typical system structure, which includes an energy generation system, an energy distribution system, an energy storage system and energy end users. Then, we summarize the optimization framework for microgrid operation, which contains the optimization objective, decision variables and constraints. Next, we systematically review the optimization algorithms for microgrid operations, of which genetic algorithms and simulated annealing algorithms are the most commonly used. Lastly, a literature bibliometric analysis is provided; the results show that the operati... [more]

The major optimization problem of the gas transmission system is to determine how to operate the compressors in a network to deliver a given flow within the pressure bounds while using minimum compressor power (minimum fuel consumption or maximum network efficiency). Minimization of fuel usage is a major objective to control gas transmission costs. This is one of the problems that has received most of the attention from both practitioners and researchers because of its economic impact. The article describes the algorithm of steady-state optimization of a high-pressure gas network of any structure that minimizes the operating cost of compressors. The developed algorithm uses the “sequential quadratic programming (SQP)” method. The tests carried out on the real network segment confirmed the correctness of the developed algorithm and, at the same time, proved its computational efficiency. Computational results obtained with the SQP method demonstrate the viability of this approach.

A new hybrid meta-heuristic approach Jaya−PPS, which is the combination of the Jaya algorithm and Powell’s Pattern Search method, is proposed in this paper to solve the optimal power flow (OPF) problem for minimization of fuel cost, emission and real power losses and total voltage deviation simultaneously. The recently developed Jaya algorithm has been applied for the exploration of search space, while the excellent local search capability of the PPS (Powell’s Pattern Search) method has been used for exploitation purposes. Integration of the local search procedure into the classical Jaya algorithm was carried out in three different ways, which resulted in three versions, namely, J-PPS1, J-PPS2 and J-PPS3. These three versions of the proposed hybrid Jaya−PPS approach were developed and implemented to solve the OPF problem in the standard IEEE 30-bus and IEEE 57-bus systems integrated with distributed generating units optimizing four objective functions simultaneously and IEEE 118-bus sy... [more]

Electricity transmission in a grid-connected system provides an effective solution to promoting clean energy accommodation. However, with arbitrary determination in current operation models, the clean energy utilization ratio (CEUR) is not satisfactory largely due to the lack of electricity curtailment (the electricity equivalent of clean energy curtailment) cost-dependent optimization. In this study, a curtailment cost-dependent multi-objective operation (CCMO) model was proposed to complementarily operate a grid-connected hybrid energy system, identify optimal CEUR, and thus maximally reduce electricity curtailment. The CCMO model centers on coupling the punishment cost of electricity curtailment with the multi-objective function defined as the total cost of each grid component. The CCMO model was solved to derive the optimal equilibrium solution determined based on multiple non-dominated solutions. A grid-connected hybrid energy system including the Yunnan, Guangdong, and Guangxi Po... [more]

Increasingly demanding environmental regulations are forcing companies to reduce their impacts caused by their activity while defending the economic viability of their manufacturing processes, especially energy and carbon-intensive ones. Therefore, these challenges must be addressed by posing optimization problems that involve several objectives simultaneously, corresponding to different conditions, and often conflicting between. In this study, the residual gases of an integral steel factory were evaluated and modeled with the goal of developing an optimization problem considering two opposing objectives: CO2 emissions and profit. The problem was first approached in a mono-objective manner, optimizing profit through Mixed Integer Linear Programming (MILP), and then was extended to a bi-objective problem solved by means of the ε-constraint method, to find the Pareto front relating profit and CO2 emissions. The results show that multiobjective optimization is a very valuable resource for... [more]

The aerodynamic performance improvement of radial impellers is of positive significance to improve the overall performance of hydrogen fuel cell systems (FCS). Our team proposes a multi-degree-of-freedom (MDOF) surface parameterization method for the global automatic optimization of radial impeller aerodynamics. The MDOF surface parameterization is characterized by fewer variables, construction ease, smoothness, good flexibility, and blade strength maintenance. In this paper, a radial impeller for a 100-kW fuel cell stack is optimized, showing the isentropic efficiency increase of 0.7%, the flow rate increase of 3.77%, and the total pressure ratio increase of 0.37%. The results revealed that the performance of the optimized radial impeller significantly improved, verifying the validity and reliability of the proposed novel design optimization method and providing technical support and methodological research of radial impeller aerodynamic optimization for hydrogen FCS.

Countries worldwide must dramatically reduce their emissions to achieve the goal of limiting temperature increases in line with the Paris Agreement. Involving developing countries in global actions on emission reduction will greatly enhance the effectiveness of global warming mitigation. This study investigated the feasibility of establishing a wind farm at four onshore and three offshore sites in Indonesia. Installing wind turbines with the highest hub height, largest rotor diameter, and lowest cut-in and rated wind speed in an identified area off Wetar Island presented the highest time-based availability and a capacity factor of 46%, as well as the highest power-based availability at 76%. The levelized cost of electricity at 0.082 USD/kWh was comparable to that of power generated from fossil fuels, which ranges from 0.07 to 0.15 USD/kWh in Indonesia. Increasing the feed-in-tariff for wind power from the current 0.08 USD/kWh would provide sufficient incentive for investment. Moving su... [more]

The fossil-based energy system is transitioning towards a renewable energy system. One important aspect is the spatial and temporal mismatch between intermitted supply and continuous demand. To ensure a reliable and affordable energy system, we propose an integrated system approach that integrates electricity production, mobility, heating of buildings and water management with a major role for storage and conversion. The minimization of energy transport in such an integrated system indicates the need for local optimization. This study focuses on a comparison between different novel system designs for neighborhood energy and water systems with varying modes of system integration, including all-electric, power-to-heat and power-to-hydrogen. A simulation model is developed to determine the energy and water balance and carry out economic analysis to calculate the system costs of various scenarios. We show that system costs are the lowest in a scenario that combines a hydrogen boiler and he... [more]

The organic Rankine cycle (ORC) is widely accepted to produce electricity from low-grade thermal heat sources. In fact, it is a developed technology for waste-heat to electricity conversions. In this paper, an ORC made up of super-heater, turbine, regenerator, condenser, pump, economizer and evaporator is considered. An optimization model to obtain the maximum performance of such ORC, depending on the super-heater pressure, is proposed and assessed, in order to find possible new working fluids that are less pollutant with similar behavior to those traditionally used. The different super-heater pressures under analysis lie in between the condenser pressure and 80% of the critical pressure of each working fluid, taking 100 values uniformly distributed. The system and optimization algorithm have been simulated in Matlab with the CoolProp library. Results show that the twelve working fluids can be categorized into four main groups, depending on the saturation pressure at ambient conditions... [more]

Pyrolysis behavior of ionic liquid (IL) pretreated coal and sugarcane bagasse (SCB) blends through thermogravimetric analysis (TGA) was studied. Three blends of coal and SCB having 3:1, 1:1, and 1:3 ratios by weight were treated with 1-ethyl-3-methylimidazolium chloride ([Emim][Cl]) at 150 °C for 3 h. Untreated and IL treated blends were then analyzed under pyrolytic conditions in a TGA at a constant ramp rate of 20 °C/min. Kinetic and thermodynamic parameters were evaluated using ten Coats-Redfern (CR) models to assess reaction mechanism. Results showed that the untreated blends followed a definite pattern and were proportional to the concentration of SCB in the blends. IL treated blends exhibited a higher average rate of degradation and total weight loss, indicating that IL had disrupted the cross-linking structure of coal and lignocellulosic structure of SCB. This will enhance the energy generation potential of biomass through thermochemical conversion processes. The lower activatio... [more]

This paper deals with photovoltaic (PV) power plant modeling and its integration into the medium-voltage distribution network. Apart from solar cells, a simulation model includes a boost converter, voltage-oriented controller and LCL filter. The main emphasis is given to the comparison of two optimization methods—particle swarm optimization (PSO) and the Ziegler−Nichols (ZN) tuning method, approaches that are used for the parameters of Proportional-Integral (PI) controllers determination. A PI controller is commonly used because of its performance, but it is limited in its effectiveness if there is a change in the parameters of the system. In our case, the aforementioned change is caused by switching the feeders of the distribution network from an open-loop to a closed-loop arrangement. The simulation results have claimed the superiority of the PSO algorithm, while the classical ZN tuning method is acceptable in a limited area of operation.

Due to the simple structure, low inertia and the ability to operate for a long time under high-speed and high-temperature conditions, the induction motor is widely used in high-speed applications. Aiming at the most prominent loss and stress problems in high-speed induction motors, the use of low loss material and the choice of a reliable rotor structure are effective optimized methods. In this paper, the electromagnetic loss, stator temperature distribution and performance parameters of high-speed induction motor are analyzed with stator cores of different materials. In addition, for the different rotor structures, the mechanical stress is compared. Furthermore, the comparison and analysis are used to improve the motor performance and provide a reference for prototype development. A performance test of the prototype is conducted, which proves the validity of the study in this paper.

Selecting an appropriate wind farm location must be specific to a particular administrative region, which involves restrictions balance and trade-offs. Multi-criteria decision making (MCDM) and GIS are widely used in wind energy planning, but have failed to achieve the selection of an optimal location and make it difficult to establish a set of independent factors. Fuzzy measurement is an effective method to evaluate intermediate synthesis and calculates the factor weight through fuzzy integrals. In this paper, optimal wind farm location is analyzed through coupling Grid GIS technique with λ fuzzy measure. Dalian City is selected as the study area for proving the feasibility of the proposed method. Typography, meteorological, transmission facilities, biological passage, and infrastructure are taken into the index system. All the indexes are specialized into victor grid cells which are taken as the base wind farm location alternative unit. The results indicate that the Grid GIS based λ... [more]

Hydrogen purification is an important part of hydrogen energy utilization. This study aimed to perform hydrogen purification of multi-component gas (H2/CO2/CH4/CO/N2 = 0.79/0.17/0.021/0.012/0.007) by one-column vacuum pressure swing adsorption (VPSA) and pressure swing adsorption (PSA). AC5-KS was selected as the adsorbent for hydrogen purification due to its greater adsorption capacity compared to R2030. Furthermore, VPSA and PSA 10-step cycle models were established to simulate the hydrogen purification process using the Aspen Adsorption platform. The simulation results showed that the hydrogen purification performance of VPSA is better than that of PSA on AC5-KS adsorbent. The effects of feeding time and purging time on hydrogen purity and recovery were also discussed. Results showed that feeding time has a negative effect on hydrogen purity and a positive effect on hydrogen recovery, while purging time has a positive effect on hydrogen purity and a negative effect on hydrogen recov... [more]

The hybrid electric vehicle is equipped with an internal combustion engine and motor as the driving source, which can solve the problems of short driving range and slow charging of the electric vehicle. Making an effective energy management control strategy can reasonably distribute the output power of the engine and motor, improve engine efficiency, and reduce battery damage. To reduce vehicle energy consumption and excessive battery discharge at the same time, a multi-objective energy management strategy based on a particle swarm optimization algorithm is proposed. First, a simulation platform was built based on a compound power-split vehicle model. Then, the ECMS (Equivalent Consumption Minimization Strategy) was used to realize the real-time control of the model, and the penalty function was added to modify the objective function based on the current SOC (State of Charge) to maintain the SOC balance. Finally, the key parameters of ECMS were optimized by using a particle swarm optim... [more]

The need for deploying fast-charging stations for electric vehicles (EVs) is becoming essential in recent years. This need is justified by the increasing charging demand and supported by new charging technologies making EV chargers more efficient. In this paper, we provide a survey on EV fast-charging models and introduce a data-driven approach with an optimization model for deploying EV fast-chargers for both electric vehicles and heavy trucks traveling through a network of suburban highways. This deployment aims at satisfying EV charging demands while respecting the limits imposed by the electric grid. We also consider the availability of local photovoltaic (PV) farm and integrate its produced power to the proposed charging network. Finally, through a case study on Paris-Saclay area, we provide locations for EV charging stations and analyze the benefits of integrating PV power at different prices, production costs and charging capacities. The obtained results also suggest potential e... [more]

A casing treatment using inclined oblique slots (INOS) is proposed to improve the stability of the single-stage transonic axial compressor, NASA Stage 37, during operation. The slots are installed on the casing of the rotor blades. The aerodynamic performance was estimated using three-dimensional steady Reynolds-Averaged Navier-Stokes analysis. The results showed that the slots effectively increased the stall margin of the compressor with slight reductions in the pressure ratio and adiabatic efficiency. Three geometric parameters were tested in a parametric study. A single-objective optimization to maximize the stall margin was carried out using a Genetic Algorithm coupled with a surrogate model created by a radial basis neural network. The optimized design increased the stall margin by 37.1% compared to that of the smooth casing with little impacts on the efficiency and pressure ratio.

Wearable sensors to monitor vital health are becoming increasingly popular both in our daily lives and in medical diagnostics. The human body being a huge source of thermal energy makes it interesting to harvest this energy to power such wearables. Thermoelectric devices are capable of converting the abundantly available body heat into useful electrical energy using the Seebeck effect. However, high thermal resistance between the skin and the device leads to low-temperature gradients (2−10 K), making it difficult to generate useful power by this device. This study focuses on the design optimization of the micro-thermoelectric generator for such low-temperature applications and investigates the role of structural geometries in enhancing the overall power output. Electroplated p-type bismuth antimony telluride (BiSbTe) and n-type copper telluride (CuTe) materials’ properties are used in this study. All the simulations and design optimizations were completed following microfabrication con... [more]