Waste heat recovery is a key problem to be solved for metallurgical slag. Furthermore, the heat source is a current bottleneck for sewage sludge gasification technology. At present, there is no complete process system for the thermochemical conversion of sludge driven by metallurgical slag waste heat. To recover the waste heat of slag, a granulation and waste heat recovery system using the sewage sludge gasification reaction is proposed in this paper. The sludge gasification kinetics were analyzed using thermogravimetry (TG). The active catalytic components in both Cu and Ni slag were determined using X-ray diffractometry (XRD) and X-ray photoelectron spectroscopy (XPS). The results show that the metallurgical slag could improve the decomposition rate of the sludge gasification reaction. The main catalytic components were Fe3O4 and CaO for Cu slag and Ni slag, respectively. The conversion ratio was increased by 7.8% and 11.8%, while the activation energy decreased from 21.09 kJ/mol to... [more]

With the continuous integration and miniaturization of electronic devices, the heat transfer of the electronic devices continues to surge. This means that thermal management equipment with higher heat flux cooling capacity is required to maintain its normal operation. This paper systematically reviews the progress of spray cooling. In the first part, the thermal dissipation mechanism of spray cooling in the non-boiling regime and boiling regime are summarized, and the correlation formula of heat transfer is summarized. In the second part, the influencing factors of various parameters of the nozzle are summarized, the experimental research and numerical simulation research are summarized separately, and some means and methods to strengthen heat transfer are listed. In the third part, we summarize the current application research of spray cooling in some hot new fields, including electronic technology, aerospace, biomedicine, battery safety, etc. The research prospects and challenges in... [more]

This study examines the long-term relationship between carbon emissions and a number of researchers engaged in Research and Development (R&D), economic development, foreign capital inflows, renewable energy and population growth in 26 countries between 1995 and 2015. Pedroni’s panel cointegration test confirms the cointegrating relationship between the variables. Long-term elasticities are derived from FMOLS regression. Researchers in R&D and renewable energy are negatively and significantly related to carbon emissions. There is a positive and significant long-term relationship between GDPs per capita and CO2 and between the FDI and CO2. Dumitrescu and Hurlin’s panel causality test revealed unidirectional causality running from economic development to carbon emissions and feedback hypotheses between the FDI and CO2 and between renewable energy and CO2.

As a result of technological advancements in the 21st century, steam-driven ships, with an efficiency of between 36 and 38%, have been replaced by diesel-driven ships, with an efficiency of up to 55%. Accordingly, the manufacturers of the main boilers and steam turbines in ships have fought for their products to remain on the market by modernizing their construction in order to increase their competitiveness in relation to diesel drives. Based on a review of data in the literature, this article presents an analysis of the increased efficiency of ship boilers with the use of waste heat from boiler exhaust gas. This paper considers the utility of using this heat to heat up the water that supplies the boilers as well as the use of the heated air in the combustion process. The analysis takes into account the different types of heat exchangers used for these purposes and the different efficiencies of boilers made by the leading boiler manufacturers. The formulae and calculation methodologie... [more]

The article seeks to describe a more realistic approach to the transition to a carbon-neutral energy model in the current period of economic and geopolitical turbulence, with the high volatility of energy prices, and the disruption of geopolitical and logistic ties, and puts forward a set of fundamental principles for the energy transition. The hypothesis tested is that the development of low-carbon energy is based on the structural-technological diversification of production methods and rationalization of energy consumption through expanded electrification and application of energy demand-side management programs. The analysis of the main approaches to the energy transition across the world shows that many countries now prioritize renewable energy sources, even though, despite their obvious environmental benefits, they are less reliable due to their intermittent nature. The proposed principles of the energy transition draw from a more flexible, compromise approach that implies an opti... [more]

The choice of the solvent to use in the Soxhlet extraction process dramatically affects the extraction yield. In this work, ten hydrocarbon source rocks were extracted using different solvents, and the chemical compositions of their products were analyzed to assess the extraction efficiency and the differences between fractions. The results indicated that using a mixed dichloromethane (DCM) and methanol (MeOH) reagent instead of the traditional chloroform (TCM) reagent can improve extraction efficiency for all rock types except for coal. The improvement in extraction efficiency was attributed to the contributions of non-hydrocarbon compounds (NOSs). A comparative study of the biomarkers of the fractions extracted using different reagents showed no significant differences in geochemical parameters, such as ∑C22−/∑C23+, Pr/Ph, Pr/nC17, Ph/nC18, OEP1, OEP2, CPI, and hopane distribution. Additionally, the carbon isotopic compositions of the fractions varied by less than 1‱, indicating that... [more]

Maximum power point tracker (MPPT) methods work to maximize the output power of a PV system under changes in meteorological conditions. The performance of these methods depends on the complexity of the algorithm and the number of used variable inputs for obtaining the MPP value. Moreover, they oscillate around the MPP in steady-state operations, causing a waste of power and power loss. Moreover, they do not work perfectly for a PV system running under partial shading conditions. Therefore, this paper proposes modifications to the global maximum power point bald eagle search-based (GMPP BES) method so that it runs as an MPPT as well. The modifications enable the GMPP BES method to detect minor changes in insolation and temperature by observing the changes in the PV array output voltage and, accordingly, trigger the search for the suitable MPP voltage. An experimental setup using a real-time digital simulator (RTDS) was utilized to evaluate the modified GMPP BES-based method under real c... [more]

This paper presents the measured energy losses in a draw gear with NE22, XH500, LL2, and CFG flat belts. The ranges of torque capacity, slippage occurrence, and transmission efficiency of selected drive belts are also presented. Knowing the exact values of these parameters allows the selection of the most suitable belts for different applications. In addition, belt manufacturers do not provide these data accurately, leading to machine failures and downtime. The paper describes the dependence of belt efficiency and belt slippage as a function of transmission load. Running transmissions with high slippage values are associated with a significant loss of energy and efficiency, rapid wear of the belt and pulleys, and increased operating temperature. In addition, when flat belts are under excessive load, it is common for the belt to quickly fall off the pulleys, interrupting the operation of machinery and equipment. Experiments on a test bench can accurately determine the energy loss caused... [more]

The development of electric vehicles plays an important role in the field of energy conservation and emission reduction. It is necessary to improve the thermal performance of battery modules in electric vehicles and reduce the power consumption of the battery thermal management system (BTMS). In this study, the heat transfer and flow resistance performance of liquid cold plates with serpentine channels were numerically investigated and optimized. Flow rate (m˙), inlet temperature (Tin), and average heat generation (Q) were selected as key operating parameters, while average temperature (Tave), maximum temperature difference (ΔTmax), and pressure drop (ΔP) were chosen as objective functions. The Response Surface Methodology (RSM) with a face-centered central composite design (CCD) was used to construct regression models. Combined with the multi-objective non-dominated sorting genetic algorithm (NSGA-II), the Pareto-optimal solution was obtained to optimize the operation parameters. The... [more]

Hydraulic fracturing of shale gas reservoirs is characterized by large fracturing fluid consumption, long working cycle and low flowback efficiency. Huge amounts of fracturing fluid retained in shale reservoirs for a long time would definitely cause formation damage and reduce the gas production efficiency. In this work, a pressure decay method was conducted in order to measure the amount of fracturing fluid imbibition and sample permeability under the conditions of formation temperature, pressure and adsorbed methane in real time. Experimental results show that (1) the mass of imbibed fracturing fluid per unit mass of shale sample is 0.00021−0.00439 g/g considering the in-situ pressure, temperature and adsorbed methane. (2) The imbibition and flowback behavior of fracturing fluid are affected by the imbibition or flowback pressure difference, pore structure, pore surface properties, mechanical properties of shale and mineral contents. (3) 0.01 mD and 0.001 mD are the critical initial... [more]

Ocean energy systems (OESs) convert the kinetic, potential, and thermal energy from oceans and seas to electricity. These systems are broadly classified into tidal, wave, thermal, and current marine systems. If fully utilized, the OESs can supply the planet with the required electricity demand as they are capable of generating approximately 2 TW of energy. The wave energy converter (WEC) systems capture the kinetic and potential energy in the waves using suitable mechanical energy capturers such as turbines and paddles. The energy density in the ocean waves is in the range of tens of kilowatts per square meter, which makes them a very attractive energy source due to the high predictability and low variability when compared with other renewable sources. Because the final objective of any renewable energy source (RES), including the WECs, is to produce electricity, the energy capturer of the WEC systems is coupled with an electrical generator, which is controlled then by power electronic... [more]

Load survey has become a routine project for shipbuilding and shipping companies to investigate electrical load characteristics to enhance the power system planning and operation of marine vessels. In this brief perspective, we will outline a few steps to feeder losses analysis based on the result conducted by the load survey. The power flow and feeder loss analysis are extracted and used to determine the critical parameters that can significantly affect the system feeder losses used in the electrical load analysis in new ships. Exploring this new research direction will provide a more thorough understanding of feeder losses in marine vessel power systems. In this paper, a case study of container ship power loss analysis using the Newton−Raphson method is presented. The analysis results can provide shipbuilding corporations and ship owners with useful information for planning, designing, operating, and controlling shipboard power systems. As an energy-saving measure for ship microgrids... [more]

Ammonia removal from wastewater was successfully achieved by simultaneous nitrification and denitrification (SND) in a double-chamber microbial electrolysis cell (MEC). The MEC operations at different applied voltages (0.7 to 1.5 V) and initial ammonia concentrations (30 to 150 mg/L) were conducted in order to evaluate their effects on MEC performance in batch mode. The maximum nitrification efficiency of 96.8% was obtained in the anode at 1.5 V, followed by 94.11% at 1.0 V and 87.05% at 0.7. At 1.5 V, the initial ammonia concentration considerably affected the nitrification rate, and the highest nitrification rate constant of 0.1601/h was determined from a first-order linear regression at 30 mg/L ammonium nitrogen. The overall total nitrogen removal efficiency was noted to be 85% via the SND in the MEC operated at an initial ammonium concentration of 50 mg/L and an applied cell voltage of 1.5 V. The MEC operation in continuous mode could remove ammonia (50 mg/L) in a series of anode a... [more]

Besides satisfying the energy demands of buildings, distributed generation can contribute toward environmental conservation. However, determining the best configuration and operational strategy for these systems is a complex task due to the available technology options and the dynamic operating conditions of buildings and their surroundings. This work addressed the synthesis and optimization of an energy system for a commercial building (hotel). Electricity, hot water, and cooling demands were established for a hotel located in Northeast Brazil. The optimization problem was based on mixed-integer linear programming and included conventional equipment, solar energy resource (photovoltaic and thermal technologies), and biomass. The objective function of the optimization was to minimize annual economic costs, which involved considering the capital and operation costs. A reference system was established for comparison purposes, where energy demands were met conventionally (without cogenera... [more]

Lithium-ion batteries (LIBs) have been widely used in mobile devices, energy storage power stations, medical equipment, and other fields, became an indispensable technological product in modern society. However, the capacity degradation of LIBs limits their long-term deployment, which is not conducive to saving resources. What is more, it will lead to safety problems when the capacity of the battery is degraded. Failure of the battery is a key issue in the research and application of LIBs. Faced with the problem of capacity degradation, various aspects of LIBs have been studied. This paper reviews the electrochemical degradation mechanism of LIBs’ life fade, detection technologies for battery failure, methods to regulate battery capacity degradation, and battery lifetime prognostics. Finally, the development trend and potential challenges of battery capacity degradation research are prospected. All the key insights from this review are expected to advance the research on capacity fadin... [more]

This article presents a novel quadruple boost inverter (QBI) with an integrated boost stage that comprises an inductor, a capacitor, a switch, and an input source. The inductor on the input side limits the inrush current and also the capacitor charging current ripples. The QBI topology comprises a dc source, an input inductor, nine switches, three diodes, and capacitors. This produces a nine-level waveform, which reduces the need for additional filters such as inductors and capacitors. The proposed QBI is elementary, compact, and needs fewer components than existing nine levels inverter. Compared to the typical triangular carrier-based sinusoidal pulse width modulation, the newly developed parabolic level-shifted carrier has a much greater RMS value. Another advantage of the proposed topology is extension for generating higher voltage levels without increment in the blocking voltage across the switches. This makes the topology ideal for medium voltage high power applications. The outpu... [more]

In order to solve the problems of long-time consumption and high energy consumption in existing capacity detection methods of retired Ni-MH batteries, a fast and reliable capacity prediction method for retired Ni-MH batteries by multi-parameter driven analysis was proposed in this paper. This method mainly obtains several parameters through short-time measurement and pulse rapid nondestructive testing. Then, Pearson correlation coefficient and KS-test were used to analyze the correlation between the two parameters and verify the same distribution. Finally, SVR was used to predict the battery discharge capacity. The results show that the volume expansion thickness difference Δd, AC internal resistance R, terminal voltage U of the battery, charge and discharge polarization internal resistance Rf1 and R and pulse charging power P2 of the battery are strongly negatively correlated with the discharge capacity, and these characteristic parameters can effectively and reliably reflect the inte... [more]

With the rapid development of electric vehicles, the safety accidents caused by the damage and failure of lithium-ion batteries under mechanical load are increasing gradually, which increases the significance of collision safety in lithium-ion batteries. The failure threshold of the cell in a free state is different from that of the cells in the module. Therefore, the safety characteristics of cells and modules under vertical dynamic impact conditions were studied in this paper. Lithium iron phosphate (LiFePO4) batteries and assembled 2-in-10 series modules with a 100% state of charge (SOC) were tested. Analyses included the voltage, temperature, and mechanical behavior of test samples under different impact loads, extrusion positions, and indenter shapes. The results showed that the damage behavior of a battery was closely related to the contact shape, contact area, and contact position. A smaller contact area led to greater deformation; moreover, the contact area being closer to the... [more]

The energy sector is nowadays facing new challenges, mainly in the form of a massive shifting towards renewable energy sources as an alternative to fossil fuels and a diffusion of the distributed generation paradigm, which involves the application of small-scale energy generation systems. In this scenario, systems adopting one or more renewable energy sources and capable of producing several forms of energy along with some useful substances, such as fresh water and hydrogen, are a particularly interesting solution. A hybrid polygeneration system based on renewable energy sources can overcome operation problems regarding energy systems where only one energy source is used (solar, wind, biomass) and allows one to use an all-in-one integrated systems in order to match the different loads of a utility. From the point of view of scientific literature, medium- and large-scale systems are the most investigated; nevertheless, more and more attention has also started to be given to small-scale... [more]

Developing renewable energy technologies, especially solar technology, is of vital importance to cope with increasing energy consumption. The existing solar thermal systems have the disadvantages of capturing solar energy inefficiently and needing additional pumping power to circulate the working fluid. A concept of a direct absorption pump-free solar thermal system that combines the advantages of nanoparticles and pulsating heat pipes (PHP) is proposed in this work. The effects of a variety of parameters including nanoparticle types, nanoparticle concentration, and nanofluid filling rate on the performance of PHP were studied. It was found that PHP has the best filling rate (80−90%) making the best heat transfer performance and minimizing the thermal resistance. The concentration of nanoparticles affects the input power of the pulsating heat pipe and thus the operation of the PHP. The nanofluid with relatively low concentration cannot absorb enough solar energy to drive the PHP to ope... [more]

The deployment of distributed energy systems must take place paying attention to the self-consumption of renewable generation. Innovative sector coupling strategies can play that role linking local electricity and gas grids. The present work aims to evaluate the energy and economic feasibility of the Power-to-Methane strategy application in urban energy districts. A residential cluster was considered as a case study. Two PV configurations have been applied to evaluate the Substitute Natural Gas (SNG) production under different renewable excess conditions. Thereafter, the Power-to-Methane strategy was implemented by varying the system’s size. Some significant configurations have been compared to each other in terms of energy and economics. Beyond a certain threshold limit, an increase in the photovoltaic size slightly enhances the effectively self-consumed energy. The Power-to-Methane strategy can exploit all the renewable excess once the system is properly sized, almost doubling the po... [more]

It is, undoubtedly, a widespread belief that the electric vehicle (EV) is considered sustainable. However, in the manufacturing and retirement phases, EVs do not appear to be as sustainable as internal combustion vehicles (ICVs) and during the use phase, the pollution produced by EVs depends on the source of electricity generation to recharge the batteries. From an economic point of view, EVs do not appear to be competitive compared to ICVs either. However, current market trends push hard on battery EVs (BEV) and plug-in hybrid vehicles (PHEV). This study aims to analyze which of the possible mobility alternatives has more sense to be considered as the option with higher penetration in the future. To this end, four known mobility technologies (ICVs, PHEVs, BEVs, and hydrogen fuel cell EVs or FCEVs) are compared for a mid-size car using published data, through environmental and techno-economic criteria, by applying the analytic hierarchy process method in an objective manner on multiple... [more]

This numerical study investigated the flow-induced vibration (FIV) on non-heated and heated cylinders with different normalized corner radii (r*) at different Reynolds numbers (Re). Four different values of r* were considered (i.e., 0 (square cylinder), 0.5, 0.75, and 1.0 (circular cylinder)) at three different Re: 100, 150, and 200 within the laminar regime. The cylinder constrained in the axial direction and oscillated transversally was considered for a fixed nondimensional cylinder mass (m*)  of 10 and a reduced velocity (Ur) of 4.92. The effect of r* and Re could be seen in the vibration modes of cylinders. The two-dimensional incompressible Navier−Stokes and energy equations were solved together with Newton’s Second Law governing the motion of the cylinder with the help of a computational solver. Four different modes were observed in this study: Mode-I characterized by exceptionally low amplitude; Mode-II characterized by fluctuating amplitude known as hysteresis (beating); M... [more]

Underground salt caverns are widely used in large-scale energy storage, such as natural gas, compressed air, oil, and hydrogen. In order to quickly build large-scale natural gas reserves, an unusual building method was established. The method involves using the existing salt caverns left over from solution mining of salt to build energy storages. In 2007, it was first applied to Jintan Natural Gas Storage of China. Based on this successful project, several existing salt caverns were screened to build energy storages in China. Engineering experience indicates that the key to successful reusing is how to select the most suitable of the numerous available caverns and confirm it. This paper summarizes and reviews relevant theories and testing methods, including: (1) the primary selection principle for using existing salt caverns to build energy storage, (2) the testing method and evaluation theory of tightness of the existing salt cavern, and (3) the typical project case of using the exist... [more]

Battery management systems depend on open circuit voltage (OCV) characterization for state of charge (SOC) estimation in real time. The traditional approach to OCV-SOC characterization involves collecting OCV-SOC data from sample battery cells and then fitting a polynomial model to this data. The parameters of these polynomial models are known as the OCV-parameters, or OCV-SOC parameters, in battery management systems and are used for real-time SOC estimation. Even though traditional OCV-SOC characterization approaches are able to abstract the OCV-SOC behavior of a battery in a few parameters, these parameters are only applicable in high precision computing systems. However, many practical battery applications do not have access to high-precision computing resources. The typical approach in a low-precision system is to round the OCV-parameters. This paper highlights the perils of rounding the OCV parameters and proposes an alternative OCV-SOC table. First, several existing OCV-SOC para... [more]