The Ordovician strike-slip faults system in the Tahe area of the Tarim Basin provides an important opportunity for using 3D seismic data to document the structural characteristics, formation, and evolution of strike-slip faults and their relationship with oil and gas. With high-resolution 3D seismic data, the strike-slip faults are interpreted, classified, and described using the seismic coherence technique. The geometric characteristics, active periods, formation, and evolution process of strike-slip faults are analyzed, and the relationship between strike-slip faults and hydrocarbon accumulation and charging is discussed in this research project. On the map, the primary strike-slip faults on the east and west sides of the Tahe area are relatively sheared to each other, showing an “X” type conjugate fault, and the secondary strike-slip faults are scattered. In the cross-section, the primary strike-slip faults are inserted downward into the Cambrian basement and up to Devonian, and “Si... [more]

Due to uncertain photovoltaic (PV) power generation, analyzing the voltage stability of transmission networks with a large PV plant is challenging. The stability of PV output power is a critical factor in establishing PV penetration levels in active transmission networks when assessing loading capabilities. Therefore, this article contributes to enhancing the understanding of how a static synchronous compensator (STATCOM) could be used as part of the power system network. STATCOMs are often used to improve the static and transient voltage, maintain transmission limits, and reduce low-frequency disturbances. With the help of a STATCOM unit, a proper investigation and analysis of dynamic voltage stability in a transmission system are presented. The validity of the study is evaluated by the Saudi Arabia grid code (SAGC). The system being tested is comprised of a 300 MW PV plant in Sakaka, Saudi Arabia, integrated into a 17-bus transmission power network and a STATCOM, which is employed at... [more]

Tight marl is a special type of unconventional oil and gas resource, and the study on its reservoir characteristics and controlling factors is of immense scientific significance. In this paper, 113 core samples of marl from Gouxi Area, Eastern Sichuan were selected. Based on organic carbon, pyrolysis, X-ray diffraction of whole rock, and X-ray diffraction of clay analysis, the reservoir evaluation of eyelid-shaped limestone in the first member of Maokou Formation was carried out. The results show that there are obvious differences between eyelid-shaped limestone reservoirs and eyeball-shaped limestone reservoirs in the target stratum. Eyelid-shaped limestone is mainly distributed in the lower members a and c of the first member of Maokou Formation. It could be the main reservoir of low porosity and permeability tight marl, as its developed apertures, micro-fractures, and pore throat structure are obviously better than that of the eyeball-shaped limestone. As eyelid-shaped limestone fea... [more]

Cointegration theory has been recently proposed for condition monitoring and fault detection of wind turbines. However, the existing cointegration-based methods and results presented in the literature are limited and not encouraging enough for the broader deployment of the technique. To close this research gap, this paper presents a new investigation on cointegration for wind turbine monitoring using a four-year SCADA data set acquired from a commercial wind turbine. A gearbox fault is used as a testing case to validate the analysis. A cointegration-based wind turbine monitoring model is established using five process parameters, including the wind speed, generator speed, generator temperature, gearbox temperature, and generated power. Two different sets of SCADA data were used to train the cointegration-based model and calculate the normalized cointegrating vectors. The first training data set involves 12,000 samples recorded before the occurrence of the gearbox fault, whereas the sec... [more]

Stochastic power generation is the new reality in power system management. Voltage Control mechanisms based on physical assets of the power system are deemed inadequate and are not guaranteed to lead the energy transformation in a way that ensures system security as well as cost-effective operation. Many countries that recently attained deregulated Balancing Market environments are in need of regulatory provisions and rigorous extension of electricity market mechanisms. On 1 November 2020, the Greek Electricity Market commenced operations conforming to the European Target Model. Apart from the innate difficulties a transformation such as this contains, more challenges occur as Greece is bound by European law to design market-based incentive mechanisms to remunerate Ancillary Services provided to the power system. This paper aims to examine some of the technical and regulatory aspects linked with—future—Transmission System Operator (TSO) and Distribution System Operator (DSO) cooperatio... [more]

This paper proposes a modular inverter based on Cuk converters for solar photovoltaic (PV) systems to mitigate the voltage and current mismatch issue at the PV module level. The proposed modular Cuk inverter (MCI) is formed by connecting several low-voltage (LV) microinverters (MIs) in series and linking their output sides to the distribution network. This architecture does not require a central inverter, and hence, it eliminates the need for large dc-link intermediate capacitors. The proposed MCI provides more controllability over the PV system by having a decentralized structure. The MCI will improve the PV system efficiency by reducing the voltage and current stresses in the MIs and will enable better voltage regulation due to the provided controllability. Since the proposed MI topology is based on the Cuk converter, it offers continuous input and output currents that will reduce the required filtering capacitance and will provide a wide range of voltage regulation for either supply... [more]

As a bi-directional converter, the Buck-Boost converter, which has the advantages of simple structure and taking the SOC of the battery as the balance variable, is adopted as the balance topology in this paper. In view of the shortcomings of traditional balance topology, which can only balance two adjacent batteries, resulting in a long balance time and insufficient balance accuracy, a cascade active balance charging topology that can balance in intra-group and inter-group situations simultaneously is proposed. At the same time, the fuzzy control algorithm and model predictive control are used as the balance control strategies, respectively, to control whether the MOSFET is on or off in the balance topology circuit. The duty cycle is dynamically adjusted to the size of the balance current to achieve the balance of the battery pack. The results show that the cascade Buck-Boost balance topology based on model prediction control can accurately control the balancing current and improve the... [more]

We propose a method for rapid prototyping of a three-phase AC drive system for educational purposes. The proposed method allows college students to design and manufacture a drive system comprising three-phase inverters, a permanent-magnet (PM) machine, a controller, and sensors within a semester. The rapid prototyping process, which requires less than a day, enables efficient iteration and testing during the development process. In addition to addressing the electrical design considerations, this study also addresses the mechanical aspects of the drive system, including the use of coreless PM machines fabricated, using additive manufacturing technology, and the inverter manufacturing process, utilizing an auto-milling machine. Finally, we provide details of the rapid prototyping of closed-loop control, based on sensor feedback to regulate the rotating magnetic fields and output torque.

In this study, we present an alternative maximum power point tracking technique used in a solar water pumping system to produce the maximum power for modifying the amount of pumped water. This technique was actually created primarily to regulate the duty ratio of the buck converter. In order to control the solar array operating point in order to track the maximum power point, a nonlinear control approach based on the input−output feedback linearizing technique and the Lyapunov stability theory is used. By adjusting the irradiation level, the introduced controller-containing photovoltaic generator direct current (DC) motor pump system was put to the test. Our control method was modeled in Matlab-Simulink, and simulation results were used to show that it significantly outperformed a directly connected solar generator-energized pumps operational system in terms of power extraction performance under various sunlight conditions.

Annulus pressure control is critical to well safety in deepwater oil and gas wells, and it is crucial for deepwater high-pressure oil and gas wells, which are related to production safety. At present, the deepwater annular pressure analysis model is mainly based on the trapped annulus principle. For the high annular pressure of deepwater high-pressure oil and gas wells, it brings great management and control challenges. This paper proposes a deepwater high-pressure oil and gas well annular pressure analysis method considering formation connectivity. According to the existing measures of annular pressure management and control, the differences between various types of annular pressure management and control technology are systematically analyzed and expounded, and the annular pressure management and control technology of deepwater high-pressure oil and gas wells is proposed accordingly. At the same time, combined with the actual case of a deepwater high-pressure well in the South China... [more]

Particle swarm optimisation (PSO) is one of the widely adopted meta-heuristic methods for solving real-life problems. Its practical utility can be further enhanced by improving its performance. In order to acheive this, academics have presented several variants of the original PSO over the past few years, including the quantum PSO (QPSO), bare-bones PSO (BB-PSO), hybrid PSO, fuzzy PSO, etc. In this paper, the performance of PSO is improved by proposing a fragmented swarm optimisation approach known as the PSO. The PSO is tested and compared with PSOs over 14 different benchmarking cost functions to validate its efficacy. The analysis is also carried out to see the impact of α on its performance. It is observed that the average value of the cost function over 50 simulations obtained using the fragmented swarm approach is lower than that obtained using the standard PSO in 12 out of 14 benchmark functions. Similarly, the fragmented approach outperforms the standard PSO in 13 out of 14 ben... [more]

Power generation estimation is one of the key steps in wind farm micro-sitting, and its accuracy is related to the wake decay constant in the wake model. Considering the influence of wind resource distribution in different regions, this study carried out interval optimization for the wake decay constant of offshore wind farms in the Yellow Sea region of China. Given the very small length of the sea surface roughness, atmospheric stability is a critical factor influencing the wake extent and recovery speed of offshore wind farms. WAsP 10 (Wind Atlas Analysis and Application software) simulates the wake of various scenarios, and the selection range of wake attenuation constant is investigated by combining the cases of two offshore wind farms in the Yellow Sea region. The study found that the higher the atmospheric stability, the larger the wake and the lower the wake attenuation coefficient. The Yellow Sea wind farm’s wake error system is between 0.03 and 0.04, and the forecast error can... [more]

The phase-shifted full-bridge (PSFB) converter has been widely used in power supply modules due to its simple control and high output power. However, with the market’s increasing demand for higher power sources, the PSFB converter needs to face challenges in increasing its output power level. Compared to redesigning a larger power module or a larger single converter, it will be more cost-effective to achieve a higher power output by paralleling the existing converters. However, due to the manufacturing differences in circuit components, the output imbalance in parallel PSFB converter systems may damage the power modules. Thus, the influence of differences in circuit components is analyzed in this paper, and it is found that the leakage inductance and transformer ratio are the main factors resulting in errors in current sharing control. Consequently, a dynamic hybrid compensator (DHC) is proposed in this paper, that can significantly reduce the error in current sharing control via the c... [more]

This paper concerns a hybrid vibration reduction system (HVRS) equipped with a linear electrodynamic motor (LM). The objective of the study was to implement the HVRS in a scaled vehicle suspension and reveal the benefits of its application in the system. First, a mathematical model of a quarter-vehicle suspension with the HVRS was formulated. Next, the dynamic similarity method was employed to conduct numerical simulations of the passive vibration reduction system (PVRS). Subsequently, an algorithm for HVRS controlling was developed. Then, the system was investigated experimentally under deterministic and random excitations. The results confirmed the effectiveness and applicability of the proposed HVRS.

The lacustrine fine-grained sedimentary rocks in the upper interval of the fourth member of the Eocene Shahejie Formation (Es4s) in the Dongying Depression are important shale oil exploration targets in Bohai Bay Basin. They are widely distributed and rich in organic matter. In this study, samples were observed under the optical microscope and FESEM, combined with geochemical test and physical property analysis to study the sedimentary characteristics and reservoir characteristics of them. Nine lithofacies are recognized based on the mineral composition, the content of organic matter and the beddings. The middle-high organic laminated calcareous fine-grained sedimentary rocks (LF1) and the middle-high organic laminated mixed fine-grained sedimentary rocks (LF2) resulted from seasonal sediment variations and settled by suspension in the deep lake. The middle-high organic flaggy mixed fine-grained sedimentary rocks (LF3), the middle-high organic flaggy calcareous fine-grained sedimentary... [more]

After deep mining, the discontinuous deformation characteristics of roadway roofs become more and more obvious, resulting in the emergence of separation fractures in the rock mass, which seriously affects the stability of the roof rock mass. By taking the air return roadway 21204 (ARR 21204) in Hulusu Coal Mine as the engineering background, this article reveals the discontinuous deformation characteristics of deep buried roadway roofs through field research, numerical simulation, theoretical analysis and engineering practice. After roadway excavation, the rock masses in different shallow roof horizons show different degrees of stress unloading, resulting in the occurrence of discontinuous deformation phenomena in rock masses. With the rise of the roof rock horizon, the degree of discontinuous deformation fades away until a continuous deformation zone with small deformation and stable rock strata appears. In addition, with the increase in the roadway buried depth, the extent of the dis... [more]

This paper presents the first approach to a current control problem for the direct matrix converter (DMC), which makes use of the deep reinforcement learning algorithm. The main objective of this paper is to solve the real-time capability issues of traditional control schemes (e.g., finite-set model predictive control) while maintaining feasible control performance. Firstly, a deep Q-network (DQN) algorithm is utilized to train an agent, which learns the optimal control policy through interaction with the DMC system without any plant-specific knowledge. Next, the trained agent is used to make computationally efficient online control decisions since the optimization process has been carried out in the training phase in advance. The novelty of this paper lies in presenting the first proof of concept by means of controlling the load phase currents of the DMC via the DQN algorithm to deal with the excessive computational burden. Finally, simulation and experimental results are given to dem... [more]

In this paper, we present the development of a non-linear model predictive controller for the trajectory tracking of a quadrotor using the CasADi optimization framework. The non-linear dynamic model of the quadrotor was derived using Newton−Euler equations, and the control algorithm and drone dynamics were wrapped in Matlab. The proposed controller was tested by simulating the tracking of a 3D helical reference trajectory, and its efficiency was evaluated in terms of numerical performance and tracking accuracy. The results showed that the proposed controller leads to faster computational times, approximately 20 times faster than the Matlab toolbox (nlmpc), and provides better tracking accuracy than both the Matlab toolbox and classical PID controller. The robustness of the proposed control algorithm was also tested and verified under model uncertainties and external disturbances, demonstrating its ability to effectively eliminate tracking errors.

Pool boiling, enabling remarkable phase-change heat transfer, has elicited increasing attention due to its ubiquitous applications in solar thermal power stations. An explicit understanding of the effect of system pressure on pool boiling is required to enhance the phase-change heat transfer. Despite its wide application when exploring the potential mechanism of boiling, the molecular dynamics method still needs to be improved when discussing the working mechanism of system pressure. Therefore, in the present study, a novel molecular dynamics simulation method of nanoscale pool boiling was proposed. This method provides a way to change and control pressure during the phase-change process. Furthermore, the bubble nucleation and growth in nanoscale pool boiling are quantitatively investigated through pressure-control molecular dynamics simulations. We expect that this study will improve the present simulation method of pool boiling and provide useful insights to the physics of the proces... [more]

This paper describes a method for reducing the common-mode voltage in a seven-phase brushless DC motor (BLDC) drive. The conventional interleaved method used in the three-phase inverter system is extended and applied. The proposed phase-phase interleaved method is studied to apply the six-phase excitation method for controlling the seven-phase BLDC. The six-phase switching functions related with modulation index (MI) and interleaved angle are obtained, and the average of the common-mode voltage is derived mathematically. The proposed control method reduces the common-mode voltage generation by applying the optimal interleaved angle according to MI. The proposed method is verified by experimental results.

At present, hybrid renewable power systems (HRPS) are considered reliable combinations for power generation under various conditions. The challenge facing researchers and engineers today is designing and implementing a reliable, efficient, and applicable SCADA system for adequate monitoring and control of hybrid power systems. In order to analyze, observe, and control the essential parameters of an HRPS, a SCADA system is crucial. As part of this study, a low-cost, low-power, open-source SCADA (Supervisory, Control, and Data Acquisition) system for hybrid renewable energy systems is presented. The system utilizes two remote terminal units (RTUs), an Arduino Mega2560 and a Wio terminal, to communicate with all actuators and measure vital system characteristics such as voltage, current, and power. Using the Firmata protocol, a laptop serves as the main terminal unit (MTU) to communicate with the Arduino. In addition to being the system’s central component, Node-Red is utilized for proces... [more]

Wind power forecasting involves data preprocessing and modeling. In pursuit of better forecasting performance, most previous studies focused on creating various wind power forecasting models, but few studies have been published with an emphasis on new types of data preprocessing methods. Effective data preprocessing techniques and the fusion with the physical nature of the wind have been called upon as potential future research directions in recent reviews in this area. Data enrichment as a method of data preprocessing has been widely applied to forecasting problems in the consumer data universe but has not seen application in the wind power forecasting area. This study proposes data enrichment as a new addition to the existing library of data preprocessing methods to improve wind power forecasting performance. A methodological framework of data enrichment is developed with four executable steps: add error features of weather prediction sources, add features of weather prediction at ne... [more]

Existing interconnected power systems (IPSs) are being overloaded by the expansion of the industrial and residential sectors together with the incorporation of renewable energy sources, which cause serious fluctuations in frequency, voltage, and tie-line power. The automatic voltage regulation (AVR) and load frequency control (LFC) loops provide high quality power to all consumers with nominal frequency, voltage, and tie-line power deviation, ensuring the stability and security of IPS in these conditions. In this paper, a proportional integral derivative (PID) controller is investigated for the effective control of a four-area IPS. Each IPS area has five generating units including gas, thermal reheat, hydro, and two renewable energy sources, namely wind and solar photovoltaic plants. The PID controller was tuned by a meta-heuristic optimization algorithm known as a gradient-based optimizer (GBO). The integral of time multiplied by squared value of error (ITSE) was utilized as an error... [more]

The operation of water heating uses a substantial amount of energy and is responsible for 30% of a household’s overall electricity consumption. Determining methods of reducing energy demand is crucial for countries such as South Africa, where energy supply is almost exclusively electrical, 88% of it is generated by coal, and energy deficits cause frequent blackouts. Decreasing the energy consumption of tanked water heaters can be achieved by reducing the standing losses and thermal energy of the hot water used. In this paper, we evaluate various energy-saving strategies that have commonly been used and determine which strategy is best. These strategies include optimising the heating schedule, lowering the set-point temperature, reducing the volume of hot water used, and installing additional thermal insulation. The results show that the best strategy was providing optimal control of the heating element, and savings of 16.3% were achieved. This study also determined that the magnitude o... [more]

This work considers the DC part of a hybrid AC/DC microgrid with a meshed topology. We address cost minimization, battery scheduling and the power loss minimization within the power distribution network through constrained optimization. The novelty comes from applying differential flatness properties to the microgrid components and formulating the cost and constraints in terms of the associated B-splines parametrization of the flat outputs (the voltages and currents of the system). This allows us to obtain optimal power profiles to minimize the power dissipation and the cost of the electricity purchase from the external grid. These profiles are tracked by a model predictive controller at the higher level, while at a a lower level a controller deals with the operation of the switches within the DC/DC converters. Extensive simulations under nominal and fault-affected scenarios using realistic data validate the proposed approach.