Meeting the increasing global energy demand in a sustainable way is a major challenge for humanity. One of the solutions in the transportation sector is ethanol, which is currently the only economically viable direct fuel substitute. In addition to the first-generation technology, which provides the vast majority of production, better results can be continuously realized by using advanced technologies. This study aims to investigate the economic aspects and sustainability issues of ethanol production with a systematic literature review. During the selection process, 64 studies from a total of 16,141 identified articles were analyzed in-depth. There is a consensus that first-generation production methods cannot result in a long-term solution. However, advanced technologies are currently immature, and ethanol production is more expensive with them. The use of wastes/residues and coproducts can improve both the economic outlook and sustainability of the advanced technologies. Overall, the... [more]

Global warming has led to rising electricity demands due to soaring cooling load, resulting in different technologies being implemented with renewable energy options. Renewable energy has been used to partially or fully operate these cooing systems through different technology routes in both conventional and hybrid modes. The feasibility of a particular cooling process is influenced by several technological, economic, environmental and other related factors. Selection of the appropriate route also requires consideration of external factors such as local weather, cooling load requirements and the potential of possible renewable energy. Multi-criteria decision analysis is a useful tool to systematically arrive at the right option from several possible options. This tool is used to assess the feasibility of eight technology routes for three different climatic conditions. Other than the direct cooling processes, two routes of renewable energy utilization, namely, the solar photovoltaic sys... [more]

A flue gas turbine is the main energy recovery equipment in a heavy oil catalytic cracking unit. Blade erosion and fracture are the main reasons for gas turbine failure. In this study, the characteristics of the flow field and rotor stress in the gas turbine under different fume volumes are simulated and analyzed by simulation software (ANSYS). The influences of fume volume on the high-temperature fume flow field, temperature, velocity, catalyst particle movement rotor stress in the gas turbine, as well as the influence law of flue gas flow on temperature gradient, pressure gradient, velocity distribution, and the main position of blade erosion were studied. The stress distribution and maximum stress position of the impeller were also determined. It was found that the variation trends of the pressure gradient in the calculation domain of the gas turbine under different fume volumes are similar. The pressure on the working face of the rotor blade decreases gradually along the flow direc... [more]

In the research on energy management methods of plug-in hybrid electric vehicles, it is expected that a future trend will be to optimize energy management using the information provided by the global positioning system (GPS) and intelligent transportation system (ITS), which is relatively scarce in current research. This study proposes a PHEV energy management method based on travel characteristic prediction. Firstly, this study processes the historical travel data of a certain driver obtained by GPS and ITS and uses the established Markov trajectory prediction model based on key points to predict the trajectory and mileage. Then, on the basis of characteristics analysis of historical travel data, while considering traffic information to form a target cycle, the driving cycles are classified and identified based on traffic information predictions. Then, according to the reasonable SOC allocation range of the four typical cycles, the planning algorithm of the SOC reference trajectory is... [more]

Impedance measurements by EIS are used to build a physical circuit-based model that enables various fault diagnostics and lifetime predictions. These research areas are becoming increasingly crucial for the safety and preventive maintenance of fuel cell power systems. It is challenging to apply the impedance measurement up to commercial applications at the field level. Although EIS technology has been widely used to measure and analyze the characteristics of fuel cells, EIS is applicable mainly at the single-cell level. In the case of stacks constituting a power generation system in the field, it is difficult to apply EIS due to various limitations in the high-power condition with uncontrollable loads. In this paper, we present a technology that can measure EIS on-line by injecting the perturbation current to fuel cell systems operating in the field. The proposed EIS method is developed based on Simulink Real-Time so that it can be applied to embedded devices. Modeling and simulation o... [more]

Most studies on honeycomb catalysts have been conducted using simulation models and exhaust experiments from automobiles. Very few monolithic catalyst studies have been applied to the agricultural sector, especially the catalyst exhaust system for flue purification from the biomass industry. The importance of exhaust gas purification and particulate removal from biomass power plants has become critical for evaluating the performance and environmental sustainability of biomass combustion. This is one of the first studies to investigate the performance of honeycomb catalysts for the oxidation of flue (PM2.5), (CO), and (SO2) from a rice husk briquette combustion system. The experimental setup comprised a fixed-bed electric furnace, the catalyst, an aerosol sampler, and a flue gas analyzer. Rice husk (0.1 g/mL density) and rice husk briquettes (0.8 g/mL density), were burned at 600−1000 °C for 3 min. From the results, the catalyst CO conversion rate was 100% at the optimum heated temperat... [more]

One of the most critical challenges for modern power systems is to reliably supply electricity to its consumers during and in the aftermath of natural disasters. As our dependence on electrical power has increased over the years, long-term power outages can lead to devastating impacts on affected communities. Furthermore, power outages can halt the operation of water treatment plants, leading to shortages in clean water, which is essential during post-disaster recovery. One way to address this is to temporarily reconfigure power and water networks into localized networks, i.e., electric microgrids and water micro-nets, that utilize local resources to supply local demand independently of the main power grid and/or water network. Utilizing distributed energy resources such as wind and solar and treating wastewater locally for potable reuse can provide the operational flexibility for such systems to operate sustainably. However, due to uncertainties in both renewable energy generation and... [more]

In this paper, a study of the vibrations that appear in the transmission shafts of an adder gearbox used for a heavy truck is made. The truck has two engines on only one chassis and the power offered by these engines is summated and transmitted to the truck or the working machine. This type of transmission is used for oil production installation for the army. During the transportation of the installation to the workplace, only one engine is running, after mounting installation, both engines are running. This paper studies the vibrations of the adder gearbox, a complex construction, subjected to multiple operating requirements. In this regard, the authors first performed accuracy (accuracy) tests of the VIC 3D system on an original experimental mini-stand. Measurements performed on a mini disc demonstrated the validity and accuracy of the method, even if the cameras used were not high resolution. The authors applied the same principle in the case of the adder box from the truck, obtaini... [more]

Smart meters and dynamic pricing are key factors in implementing a smart grid. Dynamic pricing is one of the demand-side management methods that can shift demand from on-peak to off-peak. Furthermore, dynamic pricing can help utilities reduce the investment cost of a power system by charging different prices at different times according to system load profile. On the other hand, a dynamic pricing strategy that can satisfy residential customers is required from the customer’s perspective. Residential load profiles can be used to comprehend residential customers’ preferences for electricity tariffs. In this study, in order to analyze the preference for time-of-use (TOU) rates of Korean residential customers through residential electricity consumption data, a representative load profile for each customer can be found by utilizing the hourly consumption of median. In the feature extraction stage, six features that can explain the customer’s daily usage patterns are extracted from the repre... [more]

A natural-gas-diesel dual-fuel marine engine with a pre-chamber is a promising solution for ocean transportation to meet the International Maritime Organization (IMO) emission regulations. This engine system employs a pre-chamber with direct injection of diesel to ignite premixed natural gas due to its higher ignition energy, which can enable lower lean limit and higher thermal efficiency. The dual-fuel pre-chamber marine engine presents complex multi-regime combustion characteristics in- and outside the pre-chamber, thus posing challenges in its numerical simulation in a cost-effective manner. Therefore, this paper presents a three-dimensional modeling study for the multi-regime combustion in a large-bore two-stroke marine dual-fuel engine, proposing a novel mapping approach, which couples the well-stirred reactor (WSR) model with the G-equation model to achieve high computational accuracy and efficiency simultaneously. In-depth analysis is performed using representative exothermic re... [more]

The main aim of this paper was to classify and to analyze the expeditious resource assessment procedure to help energy planners and system designers dealing with tides and tidal currents. Depending on the geographical features of the site to be evaluated, this paper reported the easiest methods to adopt for later working plans, crucial for preliminary considerations but to be supported by in situ measurements and by a more complex and detailed modelling. While tide trends are predictable by using Laplace equations and Fourier series, tidal currents velocities prediction is not easy, requiring suitable methods or hydraulic applications. Natural and artificial sites were analyzed and the best method for each type of them was presented. The latter together highlighting the minimum set of required information was discussed and provided as a toolkit for assessing tides and tidal current energy potential.

In this study, we analyze observational and predicted wind energy datasets of the lower 48 states of the United States, and we intend to predict an optimal map for new turbines placement. Several approaches have been implemented to investigate the correlation between current wind power stations, power capacity, wind seasonality, and site selection. The correlation between stations is carried out according to Pearson correlation coefficient approach joined with the spherical law of cosines to calculate the distances. The high correlation values between the stations spaced within a distance of 100 km show that installing more turbines close to the current farms would assist the electrical grid. The total power capacity indicates that the current wind turbines are utilizing approximately 70% of the wind resources available in the turbine’s sites. The Power spectrum of Fourier’s spectral density indicates main, secondary, and harmonic frequencies correspond to yearly, semiyearly, and daily... [more]

The purpose of this study was to apply new methods of econometric models to the Life Cycle Assessment (LCA) of physical assets, by integrating investments such as maintenance, technology, sustainability, and technological upgrades, and to propose a means to evaluate the Life Cycle Investment (LCI), with emphasis on sustainability. Sustainability is a recurrent theme of existing studies and will be a concern in coming decades. As a result, equipment with a smaller environmental footprint is being continually developed. This paper presents a method to evaluate asset depreciation with an emphasis on the maintenance investment, technology depreciation, sustainability depreciation, and technological upgrade investment. To demonstrate the value added of the proposed model, it was compared with existing models that do not take the previously mentioned aspects into consideration. The econometric model is consistent with asset life cycle plans as part of the Strategic Asset Management Plan of t... [more]

Global warming is accelerating due to the increase in greenhouse gas emissions. Accordingly, research on the use of biomass as energy sources, is being actively conducted worldwide to reduce CO2 emissions. Although the production of agro-byproducts is vast, their utilization for energy production has not been fully investigated. This study suggests an optimal torrefaction process condition for agro-byproducts, such as grape branch and perilla, that have moisture content but low calorific values. To determine whether these agro-byproducts can be used for energy sources as substituents of fossil fuels, a mass reduction model was established and validated via experimental results. Thermogravimetric analysis was conducted for different heating rates, and the activation energy and frequency factor were derived through the analysis. The model was developed by changes in rate constants, moisture content, ash content, and lignocellulose content in biomass. To ascertain the optimal torrefaction... [more]

The paper provides novel insights into the physics behind the wind turbine and wind farm blockages as well as their effects on the energy yield based on the momentum and energy balance. The current work presents blockage effects at two scales: the local scale and the wind farm scale. We clarify the combined effect of local blockages when more than one turbine is present. The work demonstrates why two turbines, which are positioned one behind the other, induce a mutual decrease in energy yield. When the turbines are placed in a row, there is an increase of energy from the end to the middle of the row because of the restriction of the expansion flow. As in the case of two turbines placed behind each other, back rows induce a power decrease for the rows in front of them and the effect increases from the edge to the center. The work also elucidates for the first time how the power output of an isolated row has a maximum in the center, whereas, in a wind farm, wind turbines on the edge of t... [more]

The path to the mitigation of global climate change and global carbon dioxide emissions avoidance leads to the large-scale substitution of fossil fuels for the generation of electricity with renewable energy sources. The transition to renewables necessitates the development of large-scale energy storage systems that will satisfy the hourly demand of the consumers. This paper offers an overview of the energy storage systems that are available to assist with the transition to renewable energy. The systems are classified as mechanical (PHS, CAES, flywheels, springs), electromagnetic (capacitors, electric and magnetic fields), electrochemical (batteries, including flow batteries), hydrogen and thermal energy storage systems. Emphasis is placed on the magnitude of energy storage each system is able to achieve, the thermodynamic characteristics, the particular applications the systems are suitable for, the pertinent figures of merit and the energy dissipation during the charging and discharg... [more]

There is a potential for synergy effects in utilizing CO2 for both enhanced gas recovery (EGR) and geothermal energy extraction (CO2-plume geothermal, CPG) from natural gas reservoirs. In this study, we carried out reservoir simulations using TOUGH2 to evaluate the sensitivity of natural gas recovery, pressure buildup, and geothermal power generation performance of the combined CO2-EGR−CPG system to key reservoir and operational parameters. The reservoir parameters included horizontal permeability, permeability anisotropy, reservoir temperature, and pore-size-distribution index; while the operational parameters included wellbore diameter and ambient surface temperature. Using an example of a natural gas reservoir model, we also investigated the effects of different strategies of transitioning from the CO2-EGR stage to the CPG stage on the energy-recovery performance metrics and on the two-phase fluid-flow regime in the production well. The simulation results showed that overlapping the... [more]

Considering rising pollution as well as fuel expenses, it has now become critical to transition to a sustainable method of transportation. As a result, automakers have begun to spend on research and development in the electric vehicle (EV) industry. The amount of EVs has expanded rapidly in recent years. This is owing to new improved technology, particularly in electric motor engineering, as well as government initiatives to limit the level of environmental impact produced by combustion engines. Because EVs are powered by electricity, implementing their charging stations presents certain complications. In this paper, we have discussed the different types of EVs, such as BEVs, FCEVs, HEVs, PHEVs, and REHEVs. Even though the capacity of many of these electric car models has been substantially enhanced within the past few years, some challenges remain as a selection barrier for several customers. Considering these challenges, we have also implemented a fuzzy AHP-TOPSIS-based unified model... [more]

Due to the substantial amounts of money involved and the complex interactions of a number of different factors, managers of oil and gas companies are faced with significant challenges when making investment decisions that will increase business efficiency and achieve competitive advantages, especially through cost control. Due to the various uncertainties of the current period, optimal investment strategies are difficult to determine. Thus, through an economic analysis that includes data analysis, quantitative risk analysis scenarios, modelling and simulations, a work framework, in the form of a generic algorithm, is proposed with the aim of generating a complex procedure for optimizing investment decisions in oil field development. A complex set of elements is considered in the analysis: costs (operational expenditures (OPEX) and capital expenditures (CAPEX), daily drilling rig costs), prices (oil, gas, separation and water injection preparation), production profiles, different types... [more]

Biogas production in Poland and Ukraine seems to be a good way to both reduce greenhouse gas emissions and increase energy self-sufficiency by supplementing conventional energy sources. The aim of the research was to assess the potential of biogas production and the possibility of increasing it at the regional level of both studied countries and was conducted in 2018. The study included an analysis of seasonal heat demand, and the results showed biogas heat surpluses and shortages in each region. The financial side of the investment discussed using the example of the selected administrative unit showed that the construction costs of the biogas plant would be paid back after 7~9 years. The presented results also showed that Polish regions have much higher variation of biogas production potential (0.14~1.09 billion m3) than Ukrainian regions (0.09~0.3 billion m3). The analysis of the possibilities of increasing the potential based on the cultivation of maize in wastelands showed that in... [more]

Wind energy is particularly significant in the power system today since it is a cheap and clean power source. The unpredictability of wind speed leads to uncertainty in devolved power which increases the difficulty in wind energy system operation. This paper presents a stochastic optimal power flow (SCOPF) for obtaining the best scheduled power from wind farms while lowering total operational costs. A novel metaheuristics method called Aquila Optimizer (AO) is used to address the SCOPF problem due to its highly nonconvex and nonlinear nature. Wind speed is represented by the Weibull probability distribution function (PDF), which is used to anticipate the cost of wind-generated power from a wind farm based on scheduled power. Weibull parameters that provide the best match to wind data are estimated using the AO approach. The suggested wind generation cost model includes the opportunity costs of wind power underestimation and overestimation. Three IEEE systems (30, 57, and 118) are utili... [more]

Flashover of contaminated insulators is a major problem for power systems at high altitude. Laboratory experiments have shown that the optical diagnostic method can provide extensive information on the physical process of contamination flashover. In this paper, a study of the local arc on a wet polluted surface under low pressure by using the optical diagnostic method is presented. The thickness of the continuous spectrum, spectral line intensity and the spectral composition varies significantly in different stages of the local arc development. Thermodynamic parameters of the local arc (including electron temperature, electron density and conductivity) are obtained by analyzing the spectra. Both the electron temperature and the conductivity increase with the increase in leakage current and air pressure. Although the electron density does not change significantly with an increase in leakage current, it increases significantly with an increase in air pressure. The findings of this work c... [more]

An extraction method for deep-seated thick seam deposits by underground mining with high resource recovery has remained a great challenge for Indian mining engineers, whereas the longwall top coal caving (LTCC) method has evolved as an effective method for various geo mining conditions in China and other counties. The percentage of top coal recovery (TCR) plays a predominant role in determining the feasibility of LTCC, which relies on the First Top Coal Caving Distance (FTCD). In this paper, the critical geotechnical parameters are identified, numerically simulated, and statistically analyzed, and the FTCD for Indian geo-mining conditions is developed and validated. A financial assessment is conducted, considering 70% top coal recovery at 85% performance level, cost of production escalated by 20% and fall in coal grade by two grades. The internal rate of return (IRR) for LTCC is 30.24% as per the sensitivity analysis where it is only 18% in single pass longwall method. This study contr... [more]

In many heavy machines, the use of high force drives is required. For such tasks, electrohydraulic servo drives with proportional valves are used most often. In these valves, the proportional electromagnets are applied. If high precise control is additionally required, it is necessary to use expensive servo valves or precise stepping motors. In this paper, the application of a valve with one (or with two) stepping motors in the electrohydraulic servo drive is described. Such motors may work in a micro-step mode, which enables the precise positioning of the valve spool with low energy consumption. The control system structure that was used for positioning, consisting of such an electrohydraulic servo drive with a valve having stepping motors, is described. In the investigations, the following control parameters are considered: the number of stepping motors used, proportional gain coefficients, supply pressure, and desired step distance. The simulation model of the servo drive is propose... [more]

One of the possibilities to achieve energy neutrality of wastewater treatment plants (WWTPs) is the implementation of the anaerobic co-digestion strategy. However, a key factor in its successful implementation on the technical scale is the application of components with complementary composition to sewage sludge (SS). In the 7resent study, the influence of adding various co-substrates on the energy balance of anaerobic digestion was evaluated. The following organic wastes were used as additional components to SS: organic fraction of municipal solid waste (OFMSW) and distillery spent wash (DW) applied in two- and three-component systems. The experiments were performed in semi-flow anaerobic reactors with the volume of 40 L under mesophilic conditions (35 °C) at hydraulic retention time (HRT) of 20, 18, and 16 d. The application of substrates to SS resulted in enhancements of methane yields as compared to SS mono-digestion. The statistically significant differences were observed in terti... [more]