Self-compacting concrete (SCC) has been increasingly used in the construction sector due to its favorable characteristics in improving various durability and rheology aspects of concrete such as deformability and segregation resistance. Recently, the studies on the application of nano-alumina (NA) produced from factory wastes have been significantly considered to enhancing the performance, and mechanical strength, of SCC. Many experimental works show that NA can be used in SCC with appropriate proportion to enjoy the benefits of improved microstructure, fresh and hardened properties, durability, and resistance to elevated temperature. However, a limited detailed review is available to particularly study using NA to improve the performance of SCC, so far. Hence, the present study is conducted to fill the existing gap of knowledge. In this study, the effect of using NA in improving rheological, mechanical parameters, and elevated temperature resistance of SCC is reviewed. This research s... [more]

The article describes a technique for obtaining a quantitative assessment of the composition and structure of the petroleum dispersed system (PDS) and its individual structural formations based on the data of the component composition and infrared spectroscopy. In the PDS of heavy petroleum feedstock modified with a mixture of unsaturated carboxylic acids and four atomic alcohols, the components of the core and the inner solvation shell are different in structure. The degree of affinity of the components of the inner and outer solvation shells of the complex structural unit (CSU), as well as that of the outer solvation shell and the hydrocarbon components of the dispersion medium, increases. Nonionic additives are involved, to a greater degree, in structuring the solvation shell of the CSU and also increase the degree of its affinity with the hydrocarbon components, which leads to an increase in the dispersion of the system and a decrease in its mobility.

Airborne particulate matter (PM) pollution often occurs in the wintertime in northern China, posing a potential threat to human health. To date, there are limited studies about the metals and inorganic ions to link source apportionments and health risk assessments in the different size-segregated PM samples. In this study, our samples were collected by a high-volume air sampler from 26 December 2018 to 11 January 2019 in a high population residential area (Beijing). Water-soluble inorganic ions, metal elements in the different size-segregated PM samples were determined for health risk assessments by inhalation of PM. During the sampling period in Beijing, the average concentrations of PM1.1 and PM1.1−2.0 were 39.67 ± 10.66 μg m−3 and 32.25 ± 6.78 μg m−3. Distinct distribution profiles characterized the different elements. The markers of coal combustion Pb, As, and Se had >52% of their mass concentration in PM1.1. The average mass ratios of (NO3− + NO2−)/SO42−, Cl−/Na+, Cl−/K+, and Cl−/... [more]

This research examines a case study on the implementation of an effective approach to advanced Lean Six Sigma problem-solving within a pharmaceutical manufacturing site which manufactures acetaminophen (paracetamol containing pain relief) tablets. Though this study was completed in a single manufacturing company, the implementation of this study delivers important application and results that can be deployed in other such manufacturing companies. The manufacturing site faced backlogs in customer orders due to increased demand. Increased demand is due to brand popularity and recognition, product efficacy and a COVID 19 pandemic that intensified the demand for pain relief tablets in an already very busy site. With increased demand, to ensure timely deliveries, customer satisfaction and minimize delays, sources of site productivity losses and wastes needed to be analyzed and reduced or eliminated. Manufacturing Packaging line downtime was identified as one area of concern. The goal of the... [more]

A novel variant of NSN P systems, called numerical spiking neural P systems with a variable consumption strategy (NSNVC P systems), is proposed. Like the spiking rules consuming spikes in spiking neural P systems, NSNVC P systems introduce a variable consumption strategy by modifying the form of the production functions used in NSN P systems. Similar to the delay feature of the spiking rules, NSNVC P systems introduce a postponement feature into the production functions. The execution of the production functions in NSNVC P systems is controlled by two, i.e., polarization and threshold, conditions. Multiple synaptic channels are used to transmit the charges and the production values in NSNVC P systems. The proposed NSNVC P systems are a type of distributed parallel computing models with a directed graphical structure. The Turing universality of the proposed NSNVC P systems is proved as number generating/accepting devices. Detailed descriptions are provided for NSNVC P systems as number... [more]

The typical time-dependent decrease of the iron corrosion rate is often difficult to consider while designing Fe0-based remediation systems. One of the most promising approaches is the amendment with manganese dioxide (Fe0/MnO2 system). The resulting system is a very complex one where characterization is challenging. The present communication uses methylene blue discoloration (MB method) to characterize the Fe0/MnO2 system. Shaken batch experiments (75 rpm) for 7 days were used. The initial MB concentration was 10 mg L−1 with the following mass loading: [MnO2] = 2.3 g L−1, [sand] = 45 g L−1, and 0 < [Fe0] (g L−1) ≤ 45. The following systems where investigated: Fe0, MnO2, sand, Fe0/MnO2, Fe0/sand, and Fe0/MnO2/sand. Results demonstrated that MB discoloration is influenced by the diffusive transport of MB from the solution to the aggregates at the bottom of the test-tubes. Results confirm the complexity of the Fe0/MnO2/sand system, while establishing that both MnO2 and sand improve th... [more]

Recently, the Trailing-Edge Flap with Micro-Tab (TEF with Micro-Tab) has been exploited to enhance the performance of wind turbine blades. Moreover, it can also be used to generate more lift and delay the onset of stall. This study focused mostly on the use of TEF with Micro-Tab in wind turbine blades using NREL’s S-809 as a model airfoil. In particular, the benefits generated by TEF with Micro-Tab may be of great interest in the design of wind turbine blades. In this paper, an attempt was made to evaluate the influence of TEF with Micro-Tab on the performance of NREL’s S-809 airfoils. Firstly, a computational fluid dynamics (CFD) model for the airfoil NREL’s S-809 was established, and validated by comparison with previous studies and wind tunnel experimental data. Secondly, the effects of the flap position (H) and deflection angle (αF) on the flow behaviors were investigated. As a result, the effect of TEF on air-flow behavior was demonstrated by augmenting the pressure coefficient at... [more]

To ascertain the agronomic value of the material resulting from the compost-bedded pack (CBP) in dairy barns, a cross-over experiment was designed with eight dry non-pregnant Holstein cows. The study was performed in two 11-week periods. Bedding materials used were: (1) CBP with sawdust (S) and (2) CBP with forest biomass (FB). Samples were taken from the raw bedding materials and from the CBP across the experiment. We conducted an additional study preparing two piles, one of each CBP material, to accomplish a composting process of 3 months, where samples were also taken. Granulometry and some chemical composition characteristics of FB made it a suitable bedding material to be used as CBP, but its high moisture content limited the ability to absorb liquid manure. Both the degree of stability of the organic matter and the temperature evolution of CBP suggest that a real composting process did not occur. Finally, the composting process of the piles did not lead to any relevant change in... [more]

An experimental study on the flow pattern dynamics in a standard mixing vessel with radial baffles filled with water and induced by a pitched blade impeller pumping downward is presented. Investigation is mainly focused on detection and analysis of quasi-periodical or periodical low-frequency phenomenon connected with time- and length-scales considerably exceeding the Blade Passage Frequency (hereinafter BPF) and common turbulent eddies. This phenomenon, which is expressed as large-scale mean-flow variations, is generally known as flow Macro-Instability (hereinafter MI). It could break-down just below the liquid surface, or it crashes to the liquid surface and causes its Macro-Swelling (hereinafter MS). Our investigation was based on classical two-dimensional (2D) Particle Image Velocimetry (hereinafter PIV) measurement within 3 selected vertical planes in the vessel and subsequent analysis of the velocity field. The dominant frequencies evaluated in the selected points and overall ana... [more]

Variable selection constitutes an essential step to reduce dimensionality and improve performance of fault detection and diagnosis in large scale industrial processes. For this reason, in this paper, variable selection approaches based on causality are proposed and compared, in terms of model adjustment of available data and fault detection performance, with several other filter-based, wrapper-based, and embedded-based variable selection methods. These approaches are applied in a simulated benchmark case and an actual oil and gas industrial case considering four different learning models. The experimental results show that obtained models presented better performance during the fault detection stage when variable selection procedures based on causality were used for purpose of model building.

Stunting is one of the public health problems that has yet to be solved in Indonesia. This study developed synbiotic fermented milk with iron and zinc fortification that was then tested in a clinical setting. The product was made from skimmed milk and fructooligosaccharides (FOS) and fermented with Lactobacillus plantarum. A sample of 94 stunted children under five years old were randomly assigned to intervention or control groups. The intervention group received double-fortified synbiotic milk, while the control group drank non-fortified milk. After three months, the number of normal children in both groups, according to weight- or height-for-age z-score category, was found to be increasing. However, the difference between the two groups was not significant (p > 0.05). The study suggests that fermented milk may have a good effect on child growth. Further research is needed to deepen the potency of synbiotic fermented milk for stunted children.

An input-series output-parallel soft switching resonant circuit with balance input voltage and primary-side current is studied and implemented for direct current (DC) microgrid system applications. Two resonant circuits are connected with input-series and output-parallel structure to have the advantages of low voltage stresses on active devices and low current stresses on power diodes. A balance capacitor is adopted on high voltage side to balance two input capacitor voltages. The LLC (inductor−inductor−capacitor) resonant circuit cells are employed in the converter to have soft switching operation for power semiconductors. The magnetic coupling component is adopted on the primary-side to automatically realize current balance of the two resonant circuits. In the end, a laboratory hardware circuit is built and tested. Experiments demonstrate and prove the validity of the resonant converter.

Water scarcity due to the ever-increasing worldwide demand and climate change is one of the greatest hurdles of our time [...]

In the present study, a Box−Behnken design of response surface methodology (RSM) was employed to optimize the processing factors (force: 100, 150, and 200 kN; speed: 3, 5, and 7 mm/min; and temperature: 40, 60, and 80 °C) for extracting pumpkin seeds oil under uniaxial compression. The design generated 15 experiments including twelve combinations of factors and three replicates at the center point. The responses: oil yield (%), oil expression efficiency (%), and energy (J) were calculated, and the regression models determined were statistically analyzed and validated. The optimum factors combination: 200 kN, 4 mm/min and 80 °C predicted the oil yield of 20.48%, oil expression efficiency of 60.90%, and energy of 848.04 J. The relaxation time of 12 min at the optimum factors increased the oil efficiency to 64.53%. The lower oil point force was determined to be 57.32 kN for estimating the maximum oil output. The tangent curve and generalized Maxwell models adequately (R2 = 0.996) describe... [more]

Efficient monitoring is an open problem in the operation of anaerobic digestion processes, due to the lack of accurate, low-cost, and proper sensors for the on-line monitoring of key process variables. This paper presents two approaches for the indirect monitoring of the anaerobic digestion of cheese whey wastewater. First, the observability property is addressed using conventional and nonconventional techniques, including an observability index. Then, two model-based observer techniques, an extended Luenberger observer, a sliding mode observer, and a data-driven technique based on fractal analysis are formulated and discussed. The performance and capabilities of the proposed methodologies are illustrated on a validated model with experimental data of the anaerobic digestion of cheese whey. Experimental pH measurements are used for the data-driven approach based on fractal analysis. The experimental data sets correspond to experimental conditions (pH > 7.5 and temperature (T) = 40 °C)... [more]

The increasing clinical use of artificial medical devices raises the issue of microbial contamination, which is a risk factor for the occurrence of biofilm-associated infections. A huge amount of scientific data highlights the promising potential of essential oils (EOs) to be used for the development of novel antibiofilm strategies. We aimed to review the relevant literature indexed in PubMed and Embase and to identify the recent directions in the field of EOs, as a new modality to eradicate microbial biofilms. We paid special attention to studies that explain the mechanisms of the microbicidal and antibiofilm activity of EOs, as well as their synergism with other antimicrobials. The EOs are difficult to test for their antimicrobial activity due to lipophilicity and volatility, so we have presented recent methods that facilitate these tests. There are presented the applications of EOs in chronic wounds and biofilm-mediated infection treatment, in the food industry and as air disinfecta... [more]

The development of efficient methods for process performance verification has drawn a lot of attention in the research community. Viability theory is a mathematical tool to identify the trajectories of a dynamical system which remains in a constraint set. In this paper, viability theory is investigated for this purpose in the case of nonlinear processes that can be represented in Linear Parameter Varying (LPV) form. In particular, verification algorithms based on the use of invariance and viability kernels and capture basin are proposed. The difficulty with the application of this theory is the computation of these sets. A Lagrangian method has been used to approximate these sets. Because of simplicity and efficient computations, zonotopes are adopted for set representation. Two new sets called Safe Work Area (SWA) and Required Performance (RP) are defined and an algorithm is proposed to use these concepts for the verification purpose. Finally, two application examples based on well-kn... [more]

Ionic liquids can typically be synthesized via protonation, alkylation, metathesis, or neutralization reactions. The many types of ionic liquids have increased their attractiveness to researchers for employment in various areas, including in polymer composites. Recently, ionic liquids have been employed to modify nanofillers for the fabrication of polymer nanocomposites with improved physicochemical properties. In this succinct review, four types of imidazolium-based ionic liquids that are employed as modifiers—specifically alkylimidazolium halide, alkylimidazolium hexafluorophosphate, alkylimidazolium tetrafluoroborate, and alkylimidazolium bistriflimide—are reviewed. Additionally, three types of ionic liquid-modified nanofiller/polymer nanocomposites—namely ionic liquid-nanofiller/thermoplastic nanocomposites, ionic liquid-nanofiller/elastomer nanocomposites, and ionic liquid-nanofiller/thermoset nanocomposites—are described as well. The effect of imidazolium-based ionic liquids on t... [more]

Continuous manufacturing has received increasing interest because of the advantages of intrinsic safety and enhanced mass transfer in the pharmaceutical industry. However, the difficulty for scale-up has limited the application of continuous manufacturing for a long time. Recently, the tubular flow reactor equipped with the Kenics static mixer appears to be a solution for the continuous process scale-up. Although many influence factors on the mixing performance in the Kenics static mixer have been investigated, little research has been carried out on the aspect ratio. In this study, we used the coefficient of variation as the mixing evaluation index to investigate the effect of the aspect ratio (0.2−2) on the Kenics static mixer’s mixing performance. The results indicate that a low aspect ratio helps obtain a shorter mixing time and mixer length. This study suggests that adjusting the aspect ratio of the Kenics static mixer can be a new strategy for the scale-up of a continuous process... [more]

The lateral migration of elastic capsules towards a microchannel centerline plays a major role in industrial and physiological processes. Via our computational investigation, we show that a constriction connecting two straight microchannels facilitates the lateral capsule migration considerably, which is relatively slow in straight channels. Our work reveals that the significant cross-streamline migration inside the constriction is dominated by the strong hydrodynamic forces due to the capsule size. However, in the downstream straight channel, the increased interfacial deformation at higher capillary numbers or a lower viscosity ratio and lower membrane hardness results in increased lateral cross-streamline migration. Thus, our work highlights the different migration mechanisms occurring over curved and straight streamlines.

The segregation process of a single large intruder in a vibrated bed of small particles has been widely studied, but most previous studies focused on spherical intruders. In this work, the discrete element method was used to study the effects of vibration conditions and intruder shape on the dimensionless ascending velocity (va) of the intruder. The intruder was in a prolate shape with aspect ratio varied but its equivalent diameter fixed. Three equivalent diameters, namely volume-equivalent diameter, surface-area-equivalent diameter, and Sauter diameter, were used. It was found that va increases and then decreases with the rise of the dimensionless vibration amplitude (Ad) and the dimensionless vibration frequency (fd), and va increases with the decrease of the sphericity of the intruder (Φ). Moreover, the porosity variation in the vibrated bed and the granular temperature were analyzed, which can be linked to the change of va. It was further found that va can be uniformly correlated... [more]

In bio-oil upgrading, the activity and stability of the catalyst are of great importance for the catalytic hydrodeoxygenation (HDO) process. The vapor-phase HDO of guaiacol was investigated to clarify the activity, stability, and regeneration ability of Al-MCM-41 supported Pd, Co, and Fe catalysts in a fixed-bed reactor. The HDO experiment was conducted at 400 °C and 1 atm, while the regeneration of the catalyst was performed with an air flow at 500 °C for 240 min. TGA and XPS techniques were applied to study the coke deposit and metal oxide bond energy of the catalysts before and after HDO reaction. The Co and Pd−Co simultaneously catalyzed the CArO−CH3, CAr−OH, and multiple C−C hydrogenolyses, while the Fe and Pd−Fe principally catalyzed the CAr−OCH3 hydrogenolysis. The bimetallic Pd−Co and Pd−Fe showed a higher HDO yield and stability than monometallic Co and Fe, since the coke formation was reduced. The Pd−Fe catalyst presented a higher stability and regeneration ability than the P... [more]

This study investigates the effects of sodium nitrite replacement by the sage essential oil (SEO), on the physico-chemical, microbiological and sensory quality of dry fermented sausages (DFS) during 225 days of storage. The SEO (0.00, 0.05 and 0.10 µL/g) was added in DFS batters formulated with different levels of pork back fat (15% and 25%) and sodium nitrite (0, 75 and 150 mg/kg). The inclusion of SEO had no negative impact on pH, color (instrumental and sensory) and texture parameters. Total plate counts were lower than 6 log CFU (colony forming units)/g in all samples throughout the storage. Furthermore, the addition of SEO at concentration of 0.05 µL/g provided acceptable TBARS (2-Thiobarbituric acid reactive substances) values (<0.3 mg MDA (malondialdehyde)/kg) in the samples produced with reduced levels of sodium nitrite (0 and 75 mg/kg) without negative alternations on sensory attributes of odor and flavor. Generally, our findings confirmed that the usage of SEO could be a g... [more]

In order to improve the resistance to thermal fatigue and wear resistance of H13 hot-working tool steel, a nickel-based composite coating was prepared on its surface by laser cladding technology. The relationship was studied between the main processing parameters and the size of the cladding layer such as height and width. Based on the orthogonal polynomial regression method, the relationships were modeled mathematically between laser power, scanning speed, powder feeding voltage and microhardness. This model was proved to be able to predict the laser power and powder feeding voltage under 1100 Hv microhardness.

In order to improve the structural stiffness of the gravure cell structure in the solid printing process and realize a lightweight design, a multi-objective optimization design method was proposed to optimize the parameters of the direct laser engraving of the cell structure. In this paper, based on the characteristics of the cell structure and the analysis of the contact force, the ANSYS parametric design language (APDL) was used to conduct a finite element analysis on the microstructure of the regular hexagonal cell. We found that there is a certain optimization space. Then, a response surface (RSM) method optimization model, using a central composite design (CCD), was established to obtain, and then analyze, the sensitivity of each design variable to the objective functions. Finally, a multi-objective genetic algorithm (MOGA) was used to solve the model. The optimization results show that the maximum deformation was reduced by 44.4%, and the total volume was reduced by 46.3%. By com... [more]