With the integration of renewable energy sources into the power grid, a number of power electronic converters need to be connected together in parallel. Due to this interconnection among the power converters with a common DC bus, the equivalent impedance of the DC network, i.e., DC network impedance (DCNI) of these parallel converters, may vary and can cause oscillations in the DC link voltage (DCLV). In the literature, impedance models of grid-tied converters (GCs) based on the AC side are well reported without including these variations in DCNI. In addition, the dynamics of a phase-locked loop (PLL) play a significant role in GC system stability. To evaluate these stability issues, this paper proposes small signal impedance models viewing from the DC side of a three-phase GC operating under different control modes considering the PLL dynamics and the DCNI variations. Using the proposed DC impedance models (DCIM), DCLV stability analysis is evaluated for a GC. It is verified through b... [more]

Glycerol, a highly functionalised polyol, can be used as a platform molecule to produce a variety of high-value chemicals. As glycerol production is projected to increase over the coming years, it’s critically important that technology and infrastructure are developed to make use of the inevitable surplus. The catalytic production of ‘green’ mono alcohols from glycerol, in the absence of H2, is an emerging area of research that, in recent years, has generated significant industrial interest. Herein, we provide an update on recent advances in this field and discuss challenges which need to be overcome if this approach is to be considered viable industrially. The economic significance of using crude glycerol as a feedstock for glycerol valorisation strategies is also addressed and suggestions for improving the impact of research conducted in this field are proposed.

To meet the expanding energy demand, all available energy sources must be utilized. Renewable energies are both eternal and natural, but their major downside is their inconsistency. Due to the rising costs of fossil fuels and the CO2 they emit, hybrid renewable energy (HRE) sources have gained popularity as an alternative in remote and rural areas. To address this issue, a hybrid renewable energy system (HRES) can be developed by combining several energy sources. In order to build modern electrical grids that have advantages for the economy, environment, and society, the hybrid system is preferable. A summary of various optimization methods (modeling techniques) of an HRES is presented in this paper. This study offers an in-depth analysis of the best sizing, control methodologies, and energy management strategies, along with the incorporation of various renewable energy sources to form a hybrid system. Modern hybrid renewable energy system utilities rely more on an optimal design to re... [more]

TiO2 is seen as a low cost, well-known photocatalyst; nevertheless, its sluggish charge kinetics does limit its applications. To overcome this aspect, one of the recent approaches is the use of its composites with graphene to enhance its photoactivity. Graphene-based materials (nanosheets, quantum dots, etc.) allow for attachment with TiO2 nanostructures, resulting in synergistic properties and thus increasing the functionality of the resulting composite. The current review aims to present the marked progress recently achieved in the use of TiO2/graphene composites in the field of photocatalysis. In this respect, we highlight the progress and insights in TiO2 and graphene composites in photocatalysis, including the basic mechanism of photocatalysis, the possible design strategies of the composites and an overview of how to characterize the graphene in the mixed composites. The use of composites in photocatalysis has also been reviewed, in which the recent literature has opened up more... [more]

Thermal recovery is one of the most effective techniques for viscous oil production, which has been widely used in the heavy oilfield development. The mechanisms and percolation characteristics of thermal recovery have attracted a lot of attention. However, the displacement characteristics and produced oil properties in the steam flood heavy oil process are rarely addressed. In this paper, steam flooding experiments with two heavy oil viscosities under the temperatures from 120 to 200 °C and velocities from 1 to 3 mL/min were carried out to examine the oil displacement efficiency and the produced oil properties. The results show that the majority of the oil is produced in the low water cut stage. Temperature increment is helpful for prolonging the water breakthrough time. The high injection velocity of steam contributes to a high recovery factor, even if it enters into the high water cut stage. The rheology of the produced oils severely changes because the SARA composition changes, and... [more]

Excess heat can make an important contribution to reduce greenhouse gas emissions in the heating and cooling sector. Due to the local character of heat, the local excess heat potential is decisive for using excess heat. However, the spatially distributed potential and the subdivision of the potential into different subsectors have not been sufficiently investigated in Germany. Here we analyse the excess heat potential in Germany according to different subsectors and spatially distributed to the municipal level. We use data of more than 115,000 records on exhaust gas and fuel input from over 11,000 industrial sites. We calculate the site-specific excess heat potential and check its plausibility using the fuel input of the respective industrial sites. Finally, we compare the excess heat potential with the residential heat demand at the municipal level. Our results show that the excess heat potential in Germany is about 36.6 TWh/a, and that in 148 municipalities, the annual excess heat po... [more]

This paper presents automatic software for E-liked shaped contactless inductive power transfer (CIPT) device study and design that provides attended-free, multiple-case auto-generating and auto-deploying analysis in one go. It provides visualized and listed results in a design space or for optimizing solutions. To satisfy the demand for static and dynamic charging devices, the software provides specific cores, such as EE-, EI-, IE-, and II-shaped, with or without legs as optional core structures. The software contains three main parts: a user-friendly interface, analytic approaches providing grid analysis that represent the general performance in a designated parameter range, and optimal analysis for multi-objective optimization using a genetic algorithm (GA). The post-analysis processor converts the analysis results to easy-to-read outputs. Users can customize various parameters, such as core type, structural size, circuit configuration, materials, and analysis setting. Automatic func... [more]

Energy is vital for the proper functioning of the various sectors of the economy and social life. During the pandemic, there have been some changes in these aspects that need to be investigated. The main objective of this article is to identify the direction of change caused by the COVID-19 pandemic in energy consumption and energy intensity in sectors and economic areas in EU countries. The specific objectives are to identify the importance of energy consumption in sectors and areas of the economy in individual EU countries; to determine the dynamics of change and variability during the pandemic in energy consumption in individual sectors and areas of the economy in EU countries, especially during the COVID-19 pandemic; to determine the changes in energy intensity of individual economic sectors and the differences in energy intensity between individual EU countries, including during the COVID-19 pandemic. Using a purposive selection method, all 27 EU Member States were selected for th... [more]

In smart grids (SGs), the systematic utilization of consumer energy data while maintaining its privacy is of paramount importance. This research addresses this problem by energy theft detection while preserving the privacy of client data. In particular, this research identifies centralized models as more accurate in predicting energy theft in SGs but with no or significantly less data protection. Current research proposes a novel federated learning (FL) framework, namely FedDP, to tackle this issue. The proposed framework enables various clients to benefit from on-device prediction with very little communication overhead and to learn from the experience of other clients with the help of a central server (CS). Furthermore, for the accurate identification of energy theft, the use of a novel federated voting classifier (FVC) is proposed. FVC uses the majority voting-based consensus of traditional machine learning (ML) classifiers namely, random forests (RF), k-nearest neighbors (KNN), and... [more]

There has always been a high expectation that wind generation systems would capture maximum power and integrate properly with the grid. Utilizing a wind generation system with increased management to meet the growing electricity demand is a clever way of accomplishing this. However, wind power generation systems require a sophisticated, unique, and dependable control mechanism in order to achieve stability and efficiency. To improve the operation of the wind energy conversion method, researchers are continually addressing the obstacles that presently exist. Therefore, it is necessary to know which control can improve the whole system’s performance and ensure its successful integration into the network, despite the variable conductions. This article examines wind turbine control system techniques and controller trends related to the permanent magnet synchronous generator. It presents an overview of the most popular control strategies that have been used to control the PMSG wind power co... [more]

The resource orientation of the Iraqi economy implies the development of a competitive advantage of the oil industry through the industry’s infrastructure development. The authors’ assumption is that as a result of the transport and production infrastructures’ development of the extraction, processing and transportation of oil and oil products in the conditions of global economic turbulence and the availability of profitable mineral raw materials, domestic demand is restrained by both “inherited” problems and new challenges for the Iraqi oil industry. A review of changes in oil production over time has been carried out. The following problems have been identified: “inherited” problems of the oil industry’s production infrastructure, insufficient capacities and technologies and unbalanced attraction and use of investments. It has been identified that problems vary with different infrastructures. For transport infrastructure, transportation security threats, the insufficient capacity of... [more]

Recently, the CO2 power cycle has attracted attention because of tightening environmental regulations. The turbine is a factor that greatly affects the efficiency of the cycle. The radial outflow turbine is a turbomachine with the various advantages of an axial flow turbine and a radial inflow turbine, but the design theory for the turbine is uncertain. In this study, a preliminary design algorithm for a radial outflow turbine with a multi-stage configuration is presented. To verify the preliminary design algorithm, a preliminary design for a two-stage radial outflow turbine for a CO2 power cycle was carried out, and a computational fluid dynamic analysis was performed. Consequently, values close to the target performance were obtained, but blade optimization was performed to obtain more satisfactory results. The final geometry of the radial outflow turbine was obtained through optimization considering the blade exit angle related to the deviation angle, blade maximum thickness-true ch... [more]

Recently, as the use of wearable devices and the demand for eco-friendly energy have increased, many studies have been conducted on triboelectric nanogenerators (TENGs), which can economically harvest energy. Paper is considered a promising substrate and frame material that can be used to manufacture self-powered TENGs, owing to its flexibility, low cost, and accessibility. Herein, we present a sandwich-structured foldable paper-based TENG (FP-TENG) that comprises flexible materials and uses paper as a substrate. The FP-TENG can generate up to 572 mW/m2 of power via contact−separation of the triboelectric electrified body at the top and bottom. With more folds of the FP-TENG, the triboelectric cross-sectional area increases, and, thus, the electrical output increases. In addition, the proposed TENG exhibits excellent durability without signal degradation under 5000 cycles of repeated pushing motions. To demonstrate its practicality, the FP-TENG was manufactured in the form of a wristwa... [more]

The electrification of vehicles from the automotive and public transport industries can reduce harmful emissions if implemented correctly, but there is little evidence of whether the electrification of heavy freight transportation vehicles (HFTVs), such as multi-articulated vehicles, used in the freight industry could see the same benefits. This work studied heavy multi-articulated freight vehicles and developed a comparative analysis between electric and conventional diesel power trains to reduce their total emissions. Real-world drive cycle data were obtained from a heavy multi-articulated freight vehicle operating around Melbourne, Australia, with a gross combination mass (GCM) of up to 66,000 kg. Numerical models of the case study freight vehicle were then simulated with diesel, through-the-road parallel (TTRP) hybrid and electric power trains over the five different drive cycles with fuel and energy consumption results quantified. Battery weights were added on top of the real-worl... [more]

The Jianghan Basin is a lacustrine basin in central China developing multiple salt bearing deposits in the Eocene with the success of shale oil exploration in the Qianjiang Formation. The lower member of the Xingouzui Formation in the Chentuokou Depression has become another exploration target. However, rapid changes in lithofacies and strong sedimentary heterogeneity limit the exploration progress. This study aimed to explore the sequence division, lithofacies characteristics, and sedimentary environment using sedimentological, X-ray fluorescence (XRF) and X-ray diffraction (XRD) analyses. The sequence stratigraphic analysis indicates that the low member of the Xingouzui Formation is divided into two third-order sequences, namely SQ1 and SQ2, and four system tracts, including highstand systems tract (HST), lake expanding system tract (EST), early highstand system tract (EHST), and late highstand system tract (LHST). Moreover, a total of nine major lithofacies and five lithofacies asso... [more]

The huge number of electronic devices called the Internet of Things requires miniaturized, autonomous and ecologically sustainable power sources. A viable way to power these devices is by converting mechanical energy into electrical through electro-active materials. The most promising and widely used electro-active materials for mechanical energy harvesting are piezoelectric materials, where the main one used are toxic or not biocompatible. In this work, we focus our attention on biocompatible and sustainable piezoelectric materials for energy harvesting. The aim of this work is to facilitate and expedite the effort of selecting the best piezoelectric material for a specific mechanical energy harvesting application by comprehensively reviewing and presenting the latest progress in the field. We also identify and discuss the characteristic property of each material for each class to which the material belong to, in terms of piezoelectric constants and achievable power.

This work aims to investigate the influence of temperature and chemical impregnation in the textural and morphological composition of the bio-adsorbent of bio-adsorption via thermal cracking of the seeds of açaí. The experiments were carried out at 400 °C and 450 °C using a pilot scale reactor. The efficiency of the organic process was calculated in terms of liquid and solid products selected with a chemical impregnation process with NaOH, mainly with the liquid that had a greater product conversion. The elementary samples of the solid products occur with the occurrence of carbonization with an increase in the temperature of the process and the presence of impregnation. The textural and morphological characterization occurred with an analysis of FT-IR, SEM/EDS, XRF, and B.E.T. The in-phase product was developed through the creation of açaí seed in nature and impregnated with NaOH solution (2 M) at temperatures of 400 °C and 450 °C. The adsorption kinetics of acetic acid were investigat... [more]

Solar-powered adsorption chillers are a particularly interesting alternative to energy-intensive conventional refrigeration systems. Integration of the adsorption chiller with solar collectors is a very promising concept since the increase in solar radiation coincides with the increased demand for cooling. Such a solution is very economical and environmentally friendly. It also fits in with current trends related to energy policy and sustainable development. The article presents the results of tests conducted for a two-bed adsorption chiller integrated with solar collectors. The tests were performed on selected days of the summer period (July and August) at the KEZO Research Centre PAS in Jablonna (Poland). Based on the results obtained, the performance parameters of the adsorption chiller were determined, and the problems associated with the integration of all components of the system were identified and discussed. The values of the determined Coefficient of Performance (COP) and cool... [more]

As a chemical absorption method, the new ammonia carbon capture technology can capture CO2. Adding ethanol to ammonia can reduce the escape of ammonia to a certain extent and increase the absorption rate of CO2. The dissolution and crystallization of ethanol can realize the crystallization of ammonium bicarbonate and generate solid products. The induction of the crystallization process is influenced by many parameters, such as solution temperature, supersaturation, and solvating precipitant content. The basic nucleation theory is related to the critical size of nucleation. Accurate measurement of the induction period and investigating relevant factors can help to assess the nucleation kinetics. The effects of solubilizer content, temperature, and magnetic field on the induction period of the crystallization process of ammonium bicarbonate in the ethanol−H2O binary solvent mixture and determining the growth mechanism of the crystal surface by solid−liquid surface tension and surface ent... [more]

Energy storage makes energy continuously available, programmable, and at power levels different from the original intensity. This study investigates the feasibility of compressed-air energy storage (CAES) systems on a small scale. In addition to the CAES systems, there are two TES (thermal energy storage) systems for the recovery of calories and frigories. The micro-CAES + TES system is designed for a single-family residential building equipped with a photovoltaic system with a nominal power of 3 kW. The system is optimized as a potential alternative to battery storage for a typical domestic photovoltaic system. The multi-objective optimization analysis is carried out with the modeFRONTIER software. Once the best configuration of the micro-CAES + TES system is identified, it is compared with electrochemical storage systems, considering costs, durability, and performance. The efficiency of CAES (8.4%) is almost one-tenth of the efficiency of the most efficient batteries on the market (7... [more]

The organic Rankine cycles (ORCs) have been used to convert low-enthalpy geothermal brine into power. Parameter optimization and working fluid selection are the main approaches to enhance geothermal ORC performance. This work uses environmentally friendly fluids, including R1224yd(Z), R1233zd(E), R1336mzz(Z), R601 and R601a, as the geothermal ORC working fluids. The evaporation temperatures of the selected fluids were optimized to maximize the cycle net power outputs. The thermodynamic characteristics are investigated with the consideration of the influence of the allowed reinjection temperature (ARIT). Among the selected fluids, R1224yd(Z) has the highest optimal evaporation temperature with the maximum turbine power output for a brine inlet temperature (BIT) higher than 120 °C, especially at a lower allowed reinjection temperature. However, the parasitic power consumption by the pumps in an ORC with R1224yd(Z) is also higher than with the other four fluids. The net power output for O... [more]

Aiming at the problem of large vibration of a high-subside stator inner cavity curve vane pump, the force analysis of the vane at the transition curve is carried out, and the functional relationship between the vane turning angle θ, the large arc radius R, the small arc radius r and the sliding friction is established. The particle swarm algorithm is used to optimize the solution of the objective function, and the optimized parameter values are brought into the MATLAB simulation program to obtain the optimized stator curve profile diagram. The dynamic performance of the vane pump before and after optimization is simulated using ADAMS. The results show that: the acceleration of the vane pump slide is significantly reduced; the friction between the slide and the slide groove is significantly reduced; the contact force between the slide and the stator is significantly reduced; the impact vibration of the optimized vane pump is significantly reduced; and the dynamic performance of the vane... [more]

This work aims to develop a mathematical model for the simulation of a fuel cell (FC) hybrid powertrain. The work starts from modeling a single cell to obtain information on the entire FC stack. The model obtained was integrated into a simulation tool presented in the literature that simulates the longitudinal dynamics of auxiliary power unit hybrid electric vehicles and fully electric vehicles. Therefore, the integrated model allows the simulation of hybrid vehicles equipped with FC and a battery pack that acts as a peak power source. The tool simulates the mechanical and electrical behavior of the vehicle, introducing an investigation of the power flows relating to the FC and batteries. An appropriate power split logic has been implemented, allowing the correct management of the power distribution between the FC and the batteries. The importance of analyzing FC vehicles’ behavior arises from the recent necessity to find alternative propulsion systems, overcoming the range problems as... [more]

Although aviation is considered the safest mode of transportation, the annual number of pilots blinded by laser light cannot be understated. An analysis of the available statistics indicates that it is a widespread phenomenon. The stories told by the pilots show the consequences of these incidents, ranging from temporary sight loss to months of vision problems. The article also describes the current penalties for dazzling a pilot by laser light. Moreover, limited research has been conducted on the intensity of laser light of different wavelengths passing through the fairing and through standard glasses used by pilots. Understanding the effects of laser glare on pilots can help reduce adverse events and improve the ability of safety managers to develop safety procedures. Correctly designed transport systems enable effective route planning and order processing. Methods: Two types of easily available laser pointers, drawn at different distances from the aircraft, were analyzed and the int... [more]

The aim of the present research is to assess the scale of the impact of air pollution on the level of burdening EU economies with the consequences of chronic diseases (non-communicable diseases—NCDs) in the context of limiting the potential productivity of human resources. This study attempts to identify inequalities in this area that occur in the territory of the European Union. The scale of the impact of environmental factors, and air pollution in particular, on the level of health limitations in the labor resources of EU countries was measured by the number of the years of healthy life lost (YLL and YLD) as a result of chronic diseases. The verification of the assumption of a persistently high level of dispersion was based on an analysis of the convergence process (β and σ) in the group of EU countries in 1990−2019. The results demonstrate that the level of health restrictions caused by air pollution is diverse in the group of EU-27 countries. The inequalities observed concern, in p... [more]