The lack of an efficient and reliable power supply is currently one of the bottlenecks restricting the practical application of unmanned ocean detectors. Wave energy is the most widely distributed ocean energy, with the obvious advantages of high energy density and predictability. In this paper, a novel wave energy converter (WEC) for power supply of low-power unmanned ocean detectors is proposed, which is a small-scale counter-rotating self-adaptive point absorber-type WEC. The double-layer counter-rotating absorbers can achieve the torque balance of the whole device. Besides, the self-adaptation of the blade to the water flow can maintain a unidirectional continuous rotation of the single-layer absorber. The WEC has several advantages, including small occupied space, simple exchange process and convenient modular integration. It is expected to meet the power demand of low-power ocean detectors. Through modeling and CFD analysis, it was found that the power and efficiency characterist... [more]

In this paper, a smart distributed DC/DC converter synchronization advanced technique and phase angle optimization algorithm are proposed using to reduce the DC bus overall ripple. A global positioning system-based scheme is used to synchronize the carrier among the distributed converters. The carrier phase angle optimization among the different converters is inspired by Carrier-Sense Multiple Access protocol. The proposed system is simulated and analyzed using Matlab/Simulink program. As a proof of concept of the proposed technique, two case studies have been investigated under equal and unequal load sharing among the distributed generators. The proposed algorithm shows a significant reduction in the DC bus voltage ripple. To prove the concept, a laboratory test-bed has been built and the proposed algorithm has been implemented to validate the theoretical and simulation results. The close agreement between the experimental and simulation results demonstrates the effectiveness and vali... [more]

Square and circular coils are two typical topologies for coupling coils and are applied to wireless charging. However, most of the research on coupling coils is based on the finite element model (FEM), which is a time-consuming process for 3-D structure coils. In this paper, on the basis of Fourier⁻Bessel transformation and Dual Fourier transformation, two theoretical models of square and circular coils between two multilayer media are proposed. With the proposed models, we consider several important parameters such as the size of the coils, thickness, and permeability of each layer. Thus, both the self-inductance and mutual inductance of two planar coils can be calculated without much computational time. Additionally, these theoretical models can help designers figure out the different trends of self-inductance and mutual inductance, which has plenty of benefits for the preliminary pad design. Lastly, a prototype with a size of 600 mm × 600 mm and a 200 mm air gap was built in order t... [more]

In order to improve the simulation speed of the AC/DC hybrid grid, the inductance/capacitance (L/C) switch model for line-commutated converter of high-voltage direct current (LCC-HVDC) is presented in this study. The time domain modeling method is used to analyze the circuit of L/C switch model for the six-pulse system in LCC-HVDC in a switching period. A parameter setting method of L/C switch model is proposed considering the transient response, the steady state performance, switching losses and simulation error of the switch. The inductance/capacitance (L/C) switch model for LCC-HVDC has the advantage of keeping the admittance matrix unchanged regardless of the change of switching state, which improves the simulation efficiency. Finally, the validity of the parameter setting method is verified. Compared with the test results of PSCAD/EMTDC, the accuracy of the proposed LCC-HVDC simulation model is proved. The model is suitable for real-time or offline simulation of AC/DC hybrid grid.

Induction motors consume a great portion of the generated electrical energy. Moreover, most of them work at underloaded conditions, so they have low efficiencies and waste a lot of energy. Because of this, the efficiency estimation of in-service induction motors is a matter of great importance. This efficiency estimation is usually performed through indirect methods, which do not require invasive measurements of torque or speed. One of these methods is the modified Air-Gap Torque (AGT) method, which only requires voltage and current data, the stator resistance value, and the mechanical losses. This paper approaches the computation of a modified stator resistance including the mechanical losses effect to be applied in the AGT method for torque and efficiency estimation of induction motors. Some improvements are proposed in the computation of this resistance by using a direct method, as well as the possibility to estimate this parameter directly from the nameplate data of the induction m... [more]

Optimal operation of energy systems plays an important role to enhance their lifetime security and efficiency. The determination of optimal operating strategies requires intelligent utilization of massive data accumulated during operation or prediction. The investigation of these data solely without combining physical models may run the risk that the established relationships between inputs and outputs, the models which reproduce the behavior of the considered system/component in a wide range of boundary conditions, are invalid for certain boundary conditions, which never occur in the database employed. Therefore, combining big data with physical models via cyber physical systems (CPS) is of great importance to derive highly-reliable and -accurate models and becomes more and more popular in practical applications. In this paper, we focus on the description of a systematic method to apply CPS to the performance analysis and decision making of thermal power plants. We proposed a general... [more]

Astaxanthin is a valuable carotenoid, which has been approved as a food coloring by the US Food and Drug Administration and is considered as a food dye by the European Union (European Commission). This work aimed to attain Rhodosporidium toruloides mutants for enhanced astaxanthin accumulation using ultraviolet (UV) and gamma irradiation mutagenesis. Gamma irradiation was shown to be more efficient than UV for producing astaxanthin-overproducer. Among the screened mutants, G17, a gamma-induced mutant, exhibited the highest astaxanthin production, which was significantly higher than that of the wild strain. Response surface methodology was then applied to optimize the medium compositions for maximizing astaxanthin production by the mutant G17. The optimal medium compositions for the cultivation of G17 were determined as a peptone concentration of 19.75 g/L, malt extract concentration of 13.56 g/L, and glucose concentration of 19.92 g/L, with the maximum astaxanthin yield of 3021.34 µg/L... [more]

Tissue adhesives have been widely used in surgical procedures. Compared to traditional surgical sutures, tissue adhesives provide fast bonding experiences and full closure of wounds. However, current tissue adhesives are mostly fossil-based synthetic products. Therefore, it is of great significance to explore the use of natural materials in tissue adhesives. Whey is a low-end byproduct of cheese manufacturing. Whey protein, a group of small globular proteins, can exhibit adhesive properties if their structures are modified by physical or chemical means. The objectives of this study were to investigate the functional and structural properties of whey protein-based tissue adhesive, along with the antibacterial effect of totarol, a natural antimicrobial agent. Whey protein isolate (WPI) solutions (25%−33% protein) were mixed with different levels (0.1%−0.3% w/w) of totarol. The mixtures were analyzed for total plate count and yeast and mold count. The lap-shear bonding strength was tested... [more]

Cost reduction is a cornerstone of the Lean administration’s sustainability through modify its algorithms scheme to become multi-useful. This paper focuses on control “movement” waste, to minimize pipeline, cabling and sewerage network deployments time, to avoid demurrages (i.e., constructor sectors) and quickens planning through two stages. The first belongs to the build constrained hybridization of published heuristic routing methods (e.g., S-Shape, Mid-point, Largest-Gap, Return, Ascending, FLA-5, FLA-6 [Flow Line Analysis], and Composite) to select the shortest path that serves many locations (i.e., Plan-A), while allowing for the modification of these locations during service (i.e., Plan-B). The new locations are grouped into two clusters, the first of which lay on the shortest preferred path, while the second cluster contains locations that do not lay on the preferred path and are therefore moved on the backlogs-list, then use Simulated Annealing when to serve them. Finally, the... [more]

Today, industrial robots are used in dangerous environments in all sectors, including the sustainable energy sector. Sensors and processors collect and transmit information and data from users as a result of the application of robot control systems and sensory feedback. This paper proposes that the estimation of a collaborative robot system’s performance can be achieved by evaluating the mobility of robots. Scenarios have been determined in which an autonomous system has been used for intervention in crisis situations due to fire. The experimental model consists of three autonomous vehicles, two of which are ground vehicles and the other is an aerial vehicle. The conclusion of the research described in this paper highlights the fact that the integration of robotic systems made up of autonomous vehicles working in unstructured environments is difficult and at present there is no unitary analytical model.

Microwave heating has been widely used in the chemical industry because of its advantages, such as fast heating rate, selective and controllable heating, increasing reaction rate and reducing by-products in chemical reactions. The Special Issue contains research on microwave applications in chemical engineering.

Bone has a complex hierarchical structure with the capability of self-regeneration. In the case of critical-sized defects, the regeneration capabilities of normal bones are severely impaired, thus causing non-union healing of bones. Therefore, bone tissue engineering has since emerged to solve problems relating to critical-sized bone defects. Amongst the many biomaterials available on the market, calcium silicate-based (CS) cements have garnered huge interest due to their versatility and good bioactivity. In the recent decade, scientists have attempted to modify or functionalize CS cement in order to enhance the bioactivity of CS. Reports have been made that the addition of mesoporous nanoparticles onto scaffolds could enhance the bone regenerative capabilities of scaffolds. For this study, the main objective was to reuse gelatin from fish wastes and use it to combine with bone morphogenetic protein (BMP)-2 and Sr-doped CS scaffolds to create a novel BMP-2-loaded, hydrogel-based mesopo... [more]

Whiskey distillery waste streams consisting of pot ale (liquid residue) and spent grain (solid residue) are high strength organic wastes and suitable feedstock for anaerobic digestion (AD) from both economic and environmental stand points. Anaerobic digestion of pot ale and pot ale/spent grain mixtures (with mixing ratios of 1:1, 1:3, and 1:5 by wet weight) was performed after implementation of a novel hybrid pre-treatment (combined chemical and mechanical) in order to modify lignocellulosic structure and ultimately enhance digestion yield. Lignin, hemicellulose, and cellulose fractions were determined before and after chemical pre-treatment. Effects of different inoculum rates (10−30−50% on wet basis) and beating times (0−7.5−15 min) on anaerobic digestion of pot ale alone and of pot ale/spent grain mixtures were investigated in lab scale batch mode with a major focus of optimising biogas yield by using response surface methodology (RSM) in Design Expert Software. The highest biogas y... [more]

Over the past two decades, the alkaline persulfate oxidation (PO) with thermal and/or ultraviolet (UV) assisted digestion method has been widely used for digestion of nitrogen containing compounds (N-compounds) in water quality routine analysis in laboratory or on-line analysis, due to its simple principle, high conversion rate, high percent recovery, low-cost. However, this digestion method still has some inevitable problems such as complex operations, high contamination potential, batch N blanks, higher reaction temperature (120−124 °C) and time-consuming (30−60 min). In this study, ozone (O3) was selected as the oxidant for digestion of N-compounds through analysis and comparison firstly. Secondly, we proposed and compared the UV and/or ultrasound (US) combined with ozone (UV/O3, US/O3 and UV/US/O3) synergistic digestion methods based on O3 with sole O3 oxidation method on digestion efficiency (digestion time and conversion rate) of standard N-compounds. Simultaneously, the influenc... [more]

The small-scale rotating drum reactor (SS-RDR) was designed and constructed without using purge gas for the purpose of household application. The thermal and torrefaction characteristics of SS-RDR were studied and compared with other reactor types. It was found that the heat loss at the reactor wall and heat loss from exhaust gas of the SS-RDR were in the range of 6.3−12.4% and 27.9−42.8%, respectively. The increase of flue gas temperature resulted in the decrease of heat loss at the reactor wall and the increase of heat loss from exhaust gas. The heating rate of the SS-RDR was in the range of 7.3−21.4 °C/min. The higher heating value (HHV) ratio, mass yield, and energy yield ofthe SS-RDR were in the range of 1.2−1.6, 35.0−81.0%, and 56.2−96.5%, respectively. A comparison of torrefaction characteristics of various reactor types on HHV ratio-mass yield-iso-energy yield diagram indicated that the torrefaction characteristics of the SS-RDR were better than that of the rotating drum reacto... [more]

Mesoporous Mn-doped Fe nanoparticle-modified reduced graphene oxide (Mn-doped Fe/rGO) was prepared through a one-step co-precipitation method, which was then used to eliminate ethyl violet (EV) in wastewater. The prepared Mn-doped Fe/rGO was characterized by X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy, high-resolution transmission electron microscopy, scanning electron microscopy, energy dispersive spectroscopy, N2-sorption, small angle X-ray diffraction and superconducting quantum interference device. The Brunauer−Emmett−Teller specific surface area of Mn-doped Fe/rGO composites was 104.088 m2/g. The EV elimination by Mn-doped Fe/rGO was modeled and optimized by artificial intelligence (AI) models (i.e., radial basis function network, random forest, artificial neural network genetic algorithm (ANN-GA) and particle swarm optimization). Among these AI models, ANN-GA is considered as the best model for predicting the removal efficiency of EV by Mn-doped Fe/rGO... [more]

In this investigation, hydroxyapatite (HA) was synthesized using sea urchin spines (Strongylocentrotus purpuratus) via a precipitation and heat treatment method at three different temperatures (500, 600 and 700 °C). Biosynthesized HA was characterized to determine the vibration of functional groups, morphology, particle size, crystalline structure and chemical composition. For this, Fourier-Transform Infrared Spectroscopy with Attenuated Total Reflectance (FTIR-ATR), Scanning Electron Microscopy (SEM) coupled with Energy Dispersive X-ray Spectroscopy (EDS), X-ray Diffraction (XRD) and X-ray Photoelectron Spectroscopy (XPS) were used, respectively. The FTIR-ATR results reveal that the most defined characteristic HA bonds (O-H, P-O and C-O bonds) were better defined at higher synthesis temperatures. SEM also presented evidence that temperature has a significant effect on morphology. EDS results showed that the Ca/P ratio increased in the samples at higher temperatures. XRD analysis prese... [more]

The insect cell-baculovirus vector system has become one of the favorite platforms for the expression of viral vectors for vaccination and gene therapy purposes. As it is a lytic system, it is essential to balance maximum recombinant product expression with harvest time, minimizing product exposure to detrimental proteases. With this purpose, new bioprocess monitoring solutions are needed to accurately estimate culture progression. Herein, we used online digital holographic microscopy (DHM) to monitor bioreactor cultures of Sf9 insect cells. Batches of baculovirus-infected Sf9 cells producing recombinant adeno-associated virus (AAV) and non-infected cells were used to evaluate DHM prediction capabilities for viable cell concentration, culture viability and AAV titer. Over 30 cell-related optical attributes were quantified using DHM, followed by a forward stepwise regression to select the most significant (p < 0.05) parameters for each variable. We then applied multiple linear regres... [more]

Computational methods have become reliable tools in many disciplines for research and industrial design. There are, however, an ever-increasing number of details waiting to be included in the models and software, including, e.g., chemical reactions and many physical phenomena, such as particle and droplet behavior and their interactions. The dominant method for copper production, flash smelting, has been extensively investigated, but the settler part of the furnace containing molten high temperature melts termed slag and matte, still lacks a computational modeling tool. In this paper, two commercial modeling software programs have been used for simulating slag−matte interactions in the settler, the target being first to develop a robust computational fluid dynamics (CFD) model and, second, to apply a new approach for molten droplet behavior in a continuum. The latter is based on CFD coupled with the discrete element method (DEM), which was originally developed for modeling solid partic... [more]

Short-term load forecasting ensures the efficient operation of power systems besides affording continuous power supply for energy consumers. Smart meters that are capable of providing detailed information on buildings energy consumption, open several doors of opportunity to short-term load forecasting at the individual building level. In the current paper, four machine learning methods have been employed to forecast the daily peak and hourly energy consumption of domestic buildings. The utilized models depend merely on buildings historical energy consumption and are evaluated on the profiles that were not previously trained on. It is evident that developing data-driven models lacking external information such as weather and building data are of great importance under the situations that the access to such information is limited or the computational procedures are costly. Moreover, the performance evaluation of the models on separated house profiles determines their generalization abili... [more]

Phenolic acids and natural extracts, as ecofriendly environmental agents, can be used as bio bactericides against the growth of plant pathogenic bacteria. In this study, isolation trails from infected potato tubers and stems that showed soft rot symptoms in fields revealed two soft rot bacterial isolates and were initially identified through morphological, physiological, and pathogenicity tests. The molecular characterization of these isolates via PCR, based on the 16S rRNA region, was carried out by an analysis of the DNA sequence via BLAST and Genbank, and showed that the soft rot bacterial isolates belong to Pectobacterium carotovorum subsp. carotovorum (PCC1) and Dickeya solani (Ds1). The in vitro results of the tested phenolic acids against the cultured bacterial isolates proved that concentrations of 800, 1600, and 3200 μg/mL were the most effective. Ferulic acid was the potent suppressive phenolic acid tested against the Ds1 isolate, with an inhibition zone ranging from 6.00 to... [more]

To achieve the efficient utilization of low-concentration mine gas, reduce resource waste and alleviate environmental pollution, the high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50%, which is directly discharged into the atmosphere during coal mine production, was carried out to recover heat for reuse. The gas oxidation equipment was improved for the heating process and the safety of low-concentration gas oxidation under a high-temperature environment was evaluated. The experimental results showed that the reactor could provide a 1000 °C high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-tem... [more]

Basic oxygen furnaces (BOFs) are widely used to produce steel from hot metal. The process typically has limited automation which leads to sub-optimal operation. Economically optimal operation can be potentially achieved by using a dynamic optimization framework to provide operators the best combination of input trajectories. In this paper, a first-principles based dynamic model for the BOF that can be used within the dynamic optimization routine is described. The model extends a previous work by incorporating a model for slag formation and energy balances. In this new version of the mathematical model, the submodel for the decarburization in the emulsion zone is also modified to account for recent findings, and an algebraic equation for the calculation of the calcium oxide saturation in slag is developed. The dynamic model is then used to simulate the operation of two distinct furnaces. It was found that the prediction accuracy of the developed model is significantly superior to its pr... [more]

In this work, a systematic approach based on the geometric observer is proposed to design a model-based soft sensor, which allows the estimation of quality indexes in a bioreactor. The study is focused on the structure design problem where the set of innovated states has to be chosen. On the basis of robust exponential estimability arguments, it is found that it is possible to distinguish all the unmeasured states if temperature and dissolved oxygen concentration measurements are combined with substrate concentrations. The proposed estimator structure is then validated through numerical simulation considering two different measurement processor algorithms: the geometric observer and the extended Kalman filter.

New sources of polyphenols with anticancer, antioxidant, and antimicrobial properties in arid environments are critical for the development of alternative medicines and natural remedies. This study explored the polyphenol profiles and biological activities of methanolic leaf extracts from natural Mentha × piperita and Mentha longifolia populations in northern Saudi Arabia. Chromatographic analyses identified several polyphenols in M. × piperita including phenolic acids: rosmarinic acid (1547.6 mg/100 g DW (dry weight)), cryptochlorogenic acid (91.7 mg/100 g DW), and chlorogenic acid (69.4 mg/100 g DW), as well as flavonoids: naringin (328.8 mg/100 g DW) and cynaroside (162.8 mg/100 g DW). The major polyphenols in M. longifolia were: rosmarinic acid (781.6 mg/100 g DW), cryptochlorogenic acid (191.1 mg/100 g DW), p-coumaric acid (113.0 mg/100 g DW), m-coumaric acid (112.2 mg/100 g DW), and chlorogenic acid (63.8 mg/100 g DW). M. × piperita and M. longifolia leaf extracts had high antiox... [more]