In this work, a comparison between the gate-driving requirements of p-GaN HEMTs with gate contact of Schottky and Ohmic type is presented. Furthermore, the presence of a gate current of different magnitude is experimentally verified for both types of devices. Successively, the possibility of using the gate current as a temperature-sensitive parameter and its monitoring during real circuit operation is proposed. The viability of monitoring the gate current without introducing additional complexity in the gate driver is examined through experimental measurements on commercially available p-GaN HEMTs.

Solar-powered air conditioners offer a high potential for energy-efficient cooling with a high economic feasibility. They can significantly reduce the energy consumption in the building sector, which is essential to meet the greater ambition of reducing greenhouse gas emissions by 80% in the EU by 2050. This paper presents a computational model development capable of simulating the behaviour of a photovoltaic-assisted heat pump in different locations and working conditions. In addition, this model has been used to optimise a solar on-grid air conditioning system. The generated model has been validated with experimental data obtained in a real facility for a whole summer of operation (more than 100 tested days) in a Mediterranean climate (Alicante, Spain). According to the simulation results, the average Energy Efficiency Ratio (EER) of the system is 16.0, 10.7 and 7.8 in Barcelona, Madrid and Seville, respectively. The optimisation analysis has proven that the severity of the climatic... [more]

This paper is dedicated to studying and modeling the interdependence between the oil returns and exchange-rate movements of oil-exporting and oil-importing countries. Globally, twelve countries/regions are investigated, representing more than 60% and 67% of all oil exports and imports. The sample period encompasses economic and natural events like the Great Recession period (2007−2009) and the COVID-19 pandemic. We use the dynamic conditional correlation mixed-data sampling (DCC-MIDAS) model, with the aim of investigating the interdependencies expressed by the long-run correlation, which is a smoother (but always daily observed) version of the (daily) time-varying correlation. Focusing on the advent of the COVID-19 pandemic in 2020, the long-run correlations of the oil-exporting countries (Saudia Arabia, Russia, Iraq, Canada, United States, United Arab Emirates, and Nigeria) and (lagged) WTI crude oil returns strongly increase. For a subset of these countries (that is, Saudia Arabia, I... [more]

The objective of the study was to demonstrate attitudes towards wind energy facilities in the area of the Korsze Commune. The results of the study were processed using structure indices calculated from the respondents’ answers, which were analyzed in terms of social and economic factors. The study revealed that both the NIMBY syndrome and the lack of civic engagement influence attitudes towards renewable energy technologies in rural areas. The NIMBY (“not in my backyard”) term describes negative public attitudes towards proposed development projects. However, some trends towards more pronounced attitudes can be observed, depending on socioeconomic conditions. The research results imply that the measures taken to promote renewable energy technologies should be designed differently depending on the socioeconomic situation of the targeted audience. Young people might be reached via social media appropriate to their age, and through campaigns promoting local investments. For older people,... [more]

The article proposes the use of the analytic hierarchy process (AHP) method to select a risk assessment technique associated with underground hydrogen storage. The initial choosing and ranking of risk assessment techniques can be considered as a multi-criteria decision problem. The usage of a decision model based on six criteria is proposed. A ranking of methods for estimating the risks associated with underground hydrogen storage is presented. The obtained results show that the application of the AHP-based approach may be a useful tool for selecting the UHS risk assessment technique. The proposed method makes it possible to make an objective decision of the most satisfactory approach, from the point of view of all the adopted decision criteria, regarding the selection of the best risk assessment technique.

With increased usage, individual batteries within the battery pack will begin to show disparate voltage and State of Charge (SOC) profiles, which will impact the time at which batteries become balanced. Commercial battery management systems (BMSs), used in electric vehicles (EVs) and microgrids, typically send out signals suggesting removal of individual batteries or entire packs to prevent thermal runaway scenarios. To reuse these batteries, this paper presents an analysis of an off-the-shelf Orion BMS with a constrained cycling approach to assess the voltage and SOC balancing and thermal performances of such near-to-second life batteries. A scaled-down pack of series-connected batteries in 6s1p and 6s2p topologies are cycled through a combination of US06 drive and constant charge (CC) profiles using an OPAL-RT real-time Hardware-in-the-loop (HIL) simulator. These results are compared with those obtained from the Matlab/Simulink model to present the error incurred in the simulation en... [more]

Investors increasingly need to account for concerns about non-financial performance and to consider the environmental impact of fossil fuel investment. We analyze how financial investors appreciate induced seismicity in oil and gas fields in the US and the Netherlands. We employ an event study to investigate the stock market reaction of investors in two fossil fuel majors, ExxonMobil and Royal Dutch Shell. We establish that stock market participants’ response is positively but weakly related to induced seismicity with ExxonMobil. This suggests that markets might interpret this seismicity as a signal of future productivity. With Royal Dutch Shell, there is no significant association, suggesting that their investors do not specifically appreciate its externalities. We conclude that the externality of induced seismicity goes unpriced.

Electronic apparatus have become essential components of civil and industrial systems, including the automotive, home and building automation, Industrial IoT (Internet of Things) and control applications, and playing an essential role in improving security, efficiency, manageability, and rapid feedback [...]

Reconstructable dynamic simulation models of modern variable-speed wind turbines (WTs), which are integrable into any simulation software, are crucial to the scientists investigating the contribution of WTs to counteracting the current power system stability issues. The structural similarity between a doubly fed induction-generator-based (DFIG-based) WT model and a full-scale-convertor-based (FSC-based) WT model using induction generator offers the possibility of integrating them into a combined modular model with little effort and the same used parameter set. This article presents a combined root mean square (RMS) WT model, which contains a DFIG-based WT and a FSC-based WT using induction generator. The model is designed based on fundamental machine and converter equations and can be applied for classical network stability analyses. Furthermore, analogous well-performing initialization procedures for both DFIG-based and FSC-based WT models are also introduced. As an example, to demons... [more]

Due to the ban on the use of food waste as wet swine feed after the outbreak of African swine fever (ASF), 2900 tons/day of food waste and 1083 tons/day of food waste leachate were additionally generated. As an alternative treatment method for food waste leachate, the input of food waste leachate on weekends (5% of food waste leachate inflow, 100 tons/day) and its increased input (merge ratio 21.7%, 227.01 tons/day → 27.8%, 453.71 tons/day) into the digesters operated in a public sewage treatment plant were investigated. Additionally, the feasibility of the method was evaluated by analyzing the operation parameters, evaluating the operation efficiency, and identifying other environmental effects on the sewage treatment plant. In the case of input on weekends, the organic matter decomposition rate and gas production rate decreased by 8.0% and 9.5%, respectively, although the input on weekends was judged to be feasible, considering that the inflow into the WWTP increased by up to 206% du... [more]

Due to the energy transformation in buildings, the proportions of energy consumption for heating, ventilation and domestic hot water preparation (DHW) have changed. The latter component can now play a significant role, not only in the context of the annual heat demand, but also in the context of selecting the peak power of the heat source. In this paper, the comparison of chosen methods for its calculation is presented. The results show that for contemporary residential buildings, the peak power for DHW preparation can achieve the same or higher value as the peak power for heating and ventilation. For this reason, nowadays the correct selection of the peak power of a heat source for DHW purposes becomes more important, especially if it uses renewable energy sources, because it affects its size and so the investment cost and economic efficiency. It is also indicated that in modern buildings, mainly accumulative systems with hot water storage tanks should be taken into account because th... [more]

Given the substantial energy use for space cooling in buildings, integrating energy-efficient and sustainable cooling systems into buildings has become increasingly more important. Even though the cooling potential of a near-surface earth-to-air heat exchanger (EAHE) with grass cover was demonstrated in previous studies, the energy savings and environmental benefits resulting from using the EAHE have not yet been quantified. Therefore, in this study, we quantify the energy savings resulting from using a near-surface earth-to-air heat exchanger (EAHE) with grass-covered ground as a precooling unit in hot desert climates. The outlet air conditions of the EAHE during 9 months of the year (March to November), where space cooling is required, are predicted using a 3D transient CFD model, which is validated against field measurements. The EAHE is fabricated from a 1 mm thick aluminum tube with a diameter of 0.15 m and a length of 21.5 m, buried 0.4 m deep. The results showed that the EAHE ca... [more]

The decentralization in the electrical power grids has gained increasing importance, especially in the last two decades, since transmission system operators (TSO), distribution system operators (DSO) and consumers are more aware of energy efficiency and energy sustainability issues. Therefore, globally, due to the introduction of energy production technologies near the consumers, in residential and industrial sectors, new scenarios of distributed energy resources (DER) are emerging. In order to guarantee an adequate power management in the electrical power grids, incorporating producers, consumers and producers-consumers (prosumers) together, it is important to adopt intelligent systems and platforms that allow the provision of information on energy consumption and production in real time, as well as for obtaining a fair price for the sale and purchase of energy. In this paper, we analyze the literature to identify the appropriate solutions to implement a decentralized electrical power... [more]

In our recent papers, it was shown that the thermal nanocrystallization of glassy analogs of selected cathode materials led to a substantial increase in electrical conductivity. The advantage of this technique is the lack of carbon additive during synthesis. In this paper, the electrochemical performance of nanocrystalline LiFePO4 (LFP) and LiFe0.88V0.08PO4 (LFVP) cathode materials was studied and compared with commercially purchased high-performance LiFePO4 (C-LFP). The structure of the nanocrystalline materials was confirmed using X-ray diffractometry. The laboratory cells were tested at a wide variety of loads ranging from 0.1 to 3 C-rate. Their performance is discussed with reference to their microstructure and electrical conductivity. LFP exhibited a modest electrochemical performance, while the gravimetric capacity of LFVP reached ca. 100 mAh/g. This value is lower than the theoretical capacity, probably due to the residual glassy matrix in which the nanocrystallites are embedded... [more]

This study provides a workflow and preliminary estimations of the estimated ultimate recovery (EUR) volumes for natural gas and condensate liquids in the Tuwaiq Mountain Formation, the principal target in the Jafurah Field development project in Saudi Arabia. The strategic need for the field development is reviewed and the field characteristics are outlined based on public data sources complemented with data from analogous reservoirs. The target zone in the Jafurah Basin is a carbonaceous shale, being developed with up to 10,000-ft-long multistage-fractured laterals with 30 ft perforation cluster spacing and an assumed typical 1250 ft well spacing. The field will come on stream in 2024, when the gas-gathering pipeline system, natural gas processing plant, and underground gas storage facilities will all be in place. The range of uncertainties in the key reservoir parameters is taken into account to estimate preliminary EUR volumes (P90, P50, and P10) for both gas and condensates. Based... [more]

In the face of increasing demands with regard to the share of renewable energy sources in the energy mix, adsorption chillers are becoming a potentially important part of the energy transition. A key component of this type of equipment is the heat exchanger in the adsorption bed, the design of which affects both heat and mass transfer. This study includes an analysis of the geometry and materials used to manufacture such heat exchangers. The geometry analysis is mainly based on the evaluation of the impact of the different dimensions of the exchanger components on heat and mass transfer in the bed. The second part of the study focuses on material-related issues where the main emphasis is on the analysis of the thermal inertia of the exchanger. The paper analyses the latest research on the design of exchangers in adsorption beds, mainly from 2015−2021. Currently, the commonly used SCP and COP coefficients and various test conditions do not provide sufficient information for comparative... [more]

The timeliness of the complex automated diagnostics of the metal condition for all characteristics has been substantiated. An algorithm for the automation of metallographic quality control of metals is proposed and described. It is based on the use of neural networks for recognizing images of metal microstructures and a precedent method for determining the metal grade. An approach to preliminarily process the images of metal microstructures is described. The structure of a neural network has been developed to determine the quantitative characteristics of metals. The results of the functioning of neural networks for determining the quantitative characteristics of metals are presented. The high accuracy of determining the characteristics of metals using neural networks is shown. Software has been developed for the automated recognition of images of metal microstructures, and for the determination of the metal grade. Comparative results of carrying out metallographic analysis with the dev... [more]

For autonomous driving research, using a scaled vehicle platform is a viable alternative compared to a full-scale vehicle. However, using embedded solutions such as small robotic platforms with differential driving or radio-controlled (RC) car-based platforms can be limiting on, for example, sensor package restrictions or computing challenges. Furthermore, for a given controller, specialized expertise and abilities are necessary. To address such problems, this paper proposes a feasible solution, the Ridon vehicle, which is a spacious ride-on automobile with high-driving electric power and a custom-designed drive-by-wire system powered by a full-scale machine-learning-ready computer. The major objective of this paper is to provide a thorough and appropriate method for constructing a cost-effective platform with a drive-by-wire system and sensor packages so that machine-learning-based algorithms can be tested and deployed on a scaled vehicle. The proposed platform employs a modular and h... [more]

Developing energy from renewable sources and modernizing the energy system are critical components of China’s efforts to combat climate change. Policymakers and authorities have made significant attempts to bring them. However, one of the major impediments to China’s energy revolution is financial limitations, which are inextricably linked to the country’s economic growth. The present research paper intends to investigate the relationship between economic growth and sustainable financial development on the use of energy from renewable sources in both the short and long run in the context of China. To achieve this, the researchers have utilized the panel data consisting of 10 years from 2011 to 2020. When compared to cross-sectional and time-series data samples, the panel data model offers many benefits. For starters, the panel data includes information on the passage of time and the cross-sectional area. Another benefit of using panel-data models with a larger degree of freedom is that... [more]

In recent decades, due to the increase in the capabilities of microprocessors and the advent of graphics processing units (GPUs), the use of machine learning methodologies has become popular in many fields of science and technology [...]

In Generation Expansion Planning (GEP), the power plants lifetime is one of the most important factors which to the best knowledge of the authors, has not been investigated in the literature. In this article, the power plants lifetime effect on GEP is investigated. In addition, the deep learning-based approaches are widely used for time series forecasting. Therefore, a new version of Long short-term memory (LSTM) networks known as Bi-directional LSTM (BLSTM) networks are used in this paper to forecast annual peak load of the power system. For carbon emissions, the cost of carbon is considered as the penalty of pollution in the objective function. The proposed approach is evaluated by a test network and then applied to Iran power system as a large-scale grid. The simulations by GAMS (General Algebraic Modeling System, Washington, DC, USA) software show that due to consideration of lifetime as a constraint, the total cost of the GEP problem decreases by 5.28% and 7.9% for the test system... [more]

Interior permanent magnet (IPM) machines with hairpin windings have attracted significant attention in EV applications owing to their low DC resistance and excellent thermal capabilities. In this paper, we present a comprehensive investigation of AC winding losses in IPM machines for traction applications, including analytical modeling, the influence of design parameters, and finite element (FE) verification. The proposed analytical model can predict the trends in AC winding losses for any number of bar conductors and slot/pole combinations. The results of the parametric study, obtained via the analytical model, are presented to examine the effects of key design parameters, such as conductor width and height, phase arrangement, and slot-per-pole-per-phase (SPP). To incorporate more practical issues into the analysis of IPM machines with hairpin windings, extensive FE simulations were conducted. The results indicated that the AC winding losses decrease with an increasing number of condu... [more]

This paper presents the performance analysis of a latest-generation hybrid vehicle (Toyota Yaris 2020) with a testing campaign in real road conditions and a comparison with the previous model (Toyota Yaris 2017). The study was conducted by applying the Real Drive Truth Test protocol, developed by the research group, validated and spread to other full hybrid vehicles: Toyota Prius IV (2016) and Toyota Yaris 2017 (2017). In the case of the 2020 tests, the co-presence on board—deemed unsafe in the usual ways given the ongoing pandemic—was achieved through precise and sophisticated remote control. An on-board diagnostic computer, video transmission and recording equipment guarantee the virtual co-presence of a technical control room and a driver. Thus, several engineers can follow and monitor each vehicle via a 4G modem (installed in each vehicle), analysing data, route and driver behaviour in real-time, and therefore even in the presence of a single occupant in the car under test. The utm... [more]

Piezoelectric-based nano resonators are smart structures that can be used for mechanical sensors and actuators in miniature systems. In this study, the nonlinear vibration behavior of a curved piezoelectric-layered nanotube resonator was investigated. The curved structure comprises a core nanotube and a slender layer of piezoelectric material covering the inner nanotube where a harmonic voltage is applied to the piezoelectric layer. Applying the energy method and Hamiltonian principle in association with non-local theories, the governing equations of motion of the targeted system are obtained. Then, the problem is solved using the Galerkin and multiple scales methods, and the system responses under external excitation and parametric load are found. Various resonance conditions are investigated including primary and parametric resonances, and the frequency responses are obtained considering steady state motions. The effects of different parameters such as applied voltage, piezoelectric... [more]

The advent of the new millennium, with the promises of the digital age and space technology, favors humankind in every perspective. The technology provides us with electric power and has infinite use in multiple electronic accessories. The electric power produced by different sources is distributed to consumers by the transmission line and grid stations. During the electric transmission from primary sources, there are various methods by which to commit energy theft. Energy theft is a universal electric problem in many countries, with a possible loss of billions of dollars for electric companies. This energy contention is deep rooted, having so many root causes and rugged solutions of a technical nature. Advanced Metering Infrastructure (AMI) is introduced with no adequate results to control and minimize electric theft. Until now, so many techniques have been applied to overcome this grave problem of electric power theft. Many researchers nowadays use machine learning algorithms, trying... [more]