Efficient and accurate estimations of unidentified parameters of photovoltaic (PV) models are essential to their simulation. This study suggests two new variants of the whale optimization algorithm (WOA) for identifying the nine parameters of the three-diode PV model. The first variant abbreviated as RWOA is based on integrating the WOA with ranking methods under a novel updating scheme to utilize each whale within the population as much as possible during the optimization process. The second variant, namely HWOA, has been based on employing a novel cyclic exploration-exploitation operator with the RWOA to promote its local and global search for averting stagnation into local minima and accelerating the convergence speed in the right direction of the near-optimal solution. Experimentally, RWOA and HWOA are validated on a solar cell (RTC France) and two PV modules (Photowatt-PWP201 and Kyocera KC200GT). Further, these proposed variants are compared with five well-known parameter extract... [more]

The devastating nuclear disaster in Fukushima, Japan, in 2011, which was triggered by a tsunami in the wake of an earthquake, resulted in the decision to quickly phase out nuclear power and with it implicitly accelerated the German Energiewende (energy transition). To the outside observer, the decision appeared to be spontaneous and possibly due to a distorted perception of the associated risks of nuclear power. From the decision results not only the limiting uses of private property by conventional energy providers, but the exit from nuclear energy has also implications for the energy market. As with every human, political actors decide under uncertainty and incomplete information. Based on these parameters, we emphasize that the decision of a political actor is comparable to management decision-making. The paper takes this as an opportunity to examine the political decision to phase-out nuclear energy by discussing relevant parameters from the perspective of decision theory. We plead... [more]

The increasing demand for Electric Vehicle (EV) charging is putting pressure on the power grids and capacities of charging stations. This work focuses on how to use indirect control through price signals to level out the load curve in order to avoid the power consumption from exceeding these capacities. We propose mathematical programming models for the indirect control of EV charging that aim at finding an optimal set of price signals to be sent to the drivers based on price elasticities. The objective is to satisfy the demand for a given price structure, or minimize the curtailment of loads, when there is a shortage of capacity. The key contribution is the use of elasticity matrices through which it is possible to estimate the EV drivers’ reactions to the price signals. As real-world data on relating the elasticity values to the EV driver’s behaviour are currently non-existent, we concentrate on sensitivity analysis to test how different assumptions on elasticities affect the optimal... [more]

Nowadays, increasingly stricter regulations on emission reduction are inducing rapid developments in combustion science. Low-temperature combustion (LTC) is an advanced combustion technology that increases an engine’s thermal efficiency and even provides low emissions of nitrogen oxides (NOx) and particulate matter (PM). The technology often uses early direct injections to achieve sufficient mixture homogeneity. This leads to increasing wall wetting and lower combustion efficiency. This paper introduces the Multipulse ballistic injection (MBI) method to improve combustion with early injection timings. The research was carried out in a four-cylinder medium-duty diesel engine with high-pressure exhaust gas recirculation (HP-EGR). The investigation was divided into two experiments. In the first experiment, MBI was examined without EGR, and in the second, EGR was applied to study its effects. It was found that the MBI strategy decreased wall wetting and increased homogeneity and the indica... [more]

The possibility of the application of an unmanned aerial vehicle (UAV) in search and rescue activities in a deep underground mine has been investigated. In the presented case study, a UAV is searching for a lost or injured human who is able to call for help but is not able to move or use any communication device. A UAV capturing acoustic data while flying through underground corridors is used. The acoustic signal is very noisy since during the flight the UAV contributes high-energetic emission. The main goal of the paper is to present an automatic signal processing procedure for detection of a specific sound (supposed to contain voice activity) in presence of heavy, time-varying noise from UAV. The proposed acoustic signal processing technique is based on time-frequency representation and Euclidean distance measurement between reference spectrum (UAV noise only) and captured data. As both the UAV and “injured” person were equipped with synchronized microphones during the experiment, va... [more]

Traffic calming is introduced to minimise the negative results of motor vehicle use, for example, low safety level or quality of life, high noise and pollution. It can be implemented through the introduction of road infrastructure reducing the velocity and the traffic volume. In this paper, we studied how traffic-calming influences the traffic assignment. For the research, a traffic-calming measure of speed cushions on the Stachiewicza street in Krakow was taken. A method of extracting trajectories from aerial footage was shown, and it was used to build a model. For a given example, through driving characteristics research and microscopic modelling, volume−delay BPR functions were estimated—for a street with and without traffic calming. Later, a toy network of two roads of the same length, connecting the same origin and destination, was simulated using an equilibrium traffic assignment method. Simulations were conducted both with the use of PTV Vissim and Visum software and through ind... [more]

The water−energy−food nexus has captured the attention of many researchers and policy makers for the potential synergies between those sectors, including the development of self-sustainable solutions for agriculture systems. This paper poses a novel design approach aimed at balancing the trade-off between the computational burden and accuracy of the results. The method is based on the combination of static energy hub models of the system components and rule-based control to simulate the operational costs over a one-year period as well as a global optimization algorithm that provides, from those results, a design that maximizes the solar energy contribution. The presented real-world case study is based on an isolated greenhouse, whose water needs are met due to a desalination facility, both acting as heat consumers, as well as a solar thermal field and a biomass boiler that cover the demand. Considering the Almerian climate and 1 ha of tomato crops with two growing seasons, the optimal... [more]

Heat transfer enhancement techniques used in liquid piston gas compression can contribute to improving the efficiency of compressed air energy storage systems by achieving a near-isothermal compression process. This work examines the effectiveness of a simultaneous use of two proven heat transfer enhancement techniques, metal wire mesh inserts and spray injection methods, in liquid piston gas compression. By varying the dimension of the inserts and the pressure of the spray, a comparative study was performed to explore the plausibility of additional improvement. The addition of an insert can help abating the temperature rise when the insert does not take much space or when the spray flowrate is low. At higher pressure, however, the addition of spacious inserts can lead to less efficient temperature abatement. This is because inserts can distract the free-fall of droplets and hinder their speed. In order to analytically account for the compromised cooling effects of droplets, Reynolds n... [more]

During the construction of nuclear waste storage facilities, deep drilling, and geothermal energy development, high-temperature rocks are inevitably subjected to thermal shock. The physical and mechanical behaviors of granite treated with different thermal shocks were analyzed by non-destructive (P-wave velocity test) and destructive tests (uniaxial compression test and Brazil splitting test). The results show that the P-wave velocity (VP), uniaxial compressive strength (UCS), elastic modulus (E), and tensile strength (st) of specimens all decrease with the treatment temperature. Compared with air cooling, water cooling causes greater damage to the mechanical properties of granite. Thermal shock induces thermal stress inside the rock due to inhomogeneous expansion of mineral particles and further causes the initiation and propagation of microcracks which alter the mechanical behaviors of granite. Rapid cooling aggravates the damage degree of specimens. The failure pattern gradually tra... [more]

Glazed systems in buildings can account for a significant part of overall energy consumption. The unfavorable relationship between energy savings and the increased cost of energy-efficient windows is often the main drawback cited by customers to justify its non-acquisition. of glazed windows. This study addresses the relationship between the investment costs in windows and their energy performance and associated costs. Seventeen window manufacturers were contacted. This survey studied the state-of-the-art and the most-used windows in terms of energy efficiency and cost. Calumen and Guardian Configurator software were used to perform this assessment. Additionally, SEnergEd software was used to simulate the energy performance and compute the equivalent annual cost for the entire life cycle of buildings. Besides the economic benefits, the impact of the energy performance of the windows on the energy performance of the building was also studied. In terms of energy, the most efficient glazi... [more]

A new type of stepped seal with a ribbed casing is proposed to efficiently reduce the leakage at the tips of turbine blades. The leakage characteristics of two different types of labyrinth seals (conventional seal vs. ribbed seal) were compared and analyzed through computational fluid dynamics (CFD) in a wide operating range of pressure ratios and clearances. The analysis showed that the ribbed seal has superior leakage performance to the conventional seal at all clearance sizes. With the same clearance size (S/H = 1.0), the flow function of the ribbed seal was approximately 21.5−42.6% less than that of the conventional seal. Also, different trends of variation in the flow function according to the increase of the clearance were found between the conventional and ribbed seals. The leakage flow inside the labyrinth seal was analyzed to explain the cause of this difference in tendency, and it was confirmed that the added ribs cause collision between the leakage flow and the tooth wall, e... [more]

Countries of the European Union have stated transition to carbon-neutral economy until the year of 2050. Countries with a higher share of coal-fired power generation currently have no solution to end their combustion and use clean, emission-free energy immediately. The solution to this problem in the energy industry appears to be the increased use of natural gas, which significantly reduces CO2 emissions. In this article, we investigated the possibility of using coal in situ, using UCG (underground coal gasification) technology. We focused on verified geological, hydrogeological, and tectonic information about the selected brown coal deposit in Slovakia. This information has been assessed in research projects in recent years at the Technical University. From the abovementioned information, possible adverse factors were evaluated. These factors affect the rock environment around the underground generator by UCG activity. As part of the process management, measures were proposed to elimi... [more]

This work investigates the effect of production scales (laboratory, bench, and pilot) by pyrolysis of Açaí (Euterpe oleracea Mart.) seeds at 450 °C and 1.0 atmosphere, on the yields of reaction products and acid value of bio-oils. The experiments were carried out in batch mode using a laboratory scale reactor of 143 mL, a bench scale reactor of 1.5 L, and a pilot scale reactor of 143 L (≈1:10:1000). The bio-oil was obtained in pilot scale, fractionated by distillation to produce biofuel-like fractions. The distillation of bio-oil was carried out in a laboratory column. The physical-chemistry properties (density, kinematic viscosity, acid value, and refractive index) of bio-oils and distillation fractions were determined. The qualitative analysis was determined by FT-IR and the chemical composition by GC-MS. The pyrolysis showed bio-oil yields from 4.37 to 13.09 (wt.%), decreasing with reactor volume. The acid value of bio-oils varied from 68.31 to 70.26 mg KOH/g. The distillation of bi... [more]

Using biodiesel fuel in diesel engines for heavy-duty transport is important to meet the stringent emission regulations. Biodiesel is an oxygenated fuel and its physical and chemical properties are close to diesel fuel, yet there is still a need to analyze and tune the fuel injection parameters to optimize the combustion process and emissions. A four-injections strategy was used: two pilots, one main and one post injection. A highly advanced SOI decreases the NOx and the compression work but makes the combustion process less efficient. The pilot injection fuel mass influences the combustion only at injection close to the top dead center during the compression stroke. The post injection has no influence on the compression work, only on the emissions and the indicated work. An optimal injection strategy was found to be: pilot SOI 19.2 CAD BTDC, pilot injection fuel mass 25.4%; main SOI 3.7 CAD BTDC, main injection fuel mass 67.3% mg; post SOI 2 CAD ATDC, post injection fuel mass 7.3% (th... [more]

The variability in generation introduced in the electrical system by an increasing share of renewable technologies must be addressed by balancing mechanisms, demand response being a prominent one. In parallel, the massive introduction of smart meters allows for the use of high frequency energy use time series data to segment electricity customers according to their demand response potential. This paper proposes a smart meter time series clustering methodology based on a two-stage k-medoids clustering of normalized load-shape time series organized around the day divided into 48 time points. Time complexity is drastically reduced by first applying the k-medoids on each customer separately, and second on the total set of customer representatives. Further time complexity reduction is achieved using time series representation with low computational needs. Customer segmentation is undertaken with only four easy-to-interpret features: average energy use, energy−temperature correlation, entrop... [more]

Cities and nations worldwide are pledging to energy and carbon neutral objectives that imply a huge contribution from buildings. High-performance targets, either zero energy or zero carbon, are typically difficult to be reached by single buildings, but groups of properly-managed buildings might reach these ambitious goals. For this purpose we need tools and experiences to model, monitor, manage and optimize buildings and their neighborhood-level systems. The paper describes the activities pursued for the deployment of an advanced energy management system for a multi-carrier energy grid of an existing neighborhood in the area of Milan. The activities included: (i) development of a detailed monitoring plan, (ii) deployment of the monitoring plan, (iii) development of a virtual model of the neighborhood and simulation of the energy performance. Comparisons against early-stage energy monitoring data proved promising and the generation system showed high efficiency (EER equal to 5.84), to b... [more]

Combined systems for power production and thermally activated cooling have a high potential for improving the efficiency and utilisation of thermal systems. In this regard, various configurations have been proposed and are comprehensively reviewed. They are primarily based on absorption systems and the implementation of multiple levels of complexity and flexibility. The configuration of the absorption power and cooling combined cycle proposed herein has wide commercial applicability owing to its simplicity. The configuration of the components is not new. However, the utilisation of aqueous salt solutions, the comparison with ammonia chiller and with absorption power cycles, the focus on parameters that are important for real-life applications, and the comparison of the performances for constant heat input and waste heat recovery are novel. The proposed cycle is also compared with a system based on the organic Rankine cycle and vapour compression cycle. An investigation of its performan... [more]

The use of energy is a precondition for global economic and civilisational development. However, the growing demand for energy is depleting traditional energy resources and, most importantly, causing environmental pollution, mainly through the emission of greenhouse gases. As energy is necessary for the functioning of all sectors of the economy, such as industry, services, transport as well as households, these sectors are the largest contributors to energy consumption. Renewable energy sources are an alternative to generating energy from conventional fossil fuels. The main objective of this paper was to determine and compare the level, trends and variation in energy consumption by different economic sectors in countries of the European Union in 2010−2019. An analysis of the share of renewable energy consumption in different economic sectors was also carried out, as well as an assessment of the relationship of these indicators with the level of economic development of the countries and... [more]

In the case of public buildings with ceiling heating and mechanical ventilation, radiant temperature asymmetry caused by the warm ceiling and draught occur simultaneously. The currently available literature does not offer an exhaustive description of the comfort conditions resulting from such a thermal environment. This research focuses on complementing the available knowledge, using instrumental measurements, as well as subject measurements carried out on 20 individuals. Relying on these measurements, the purpose of the research is to support the understanding of the combined mechanisms of action of the two local discomfort parameters. The main result of this research is that, if the predicted percentage dissatified is less than 6%, the radiant temperature asymmetry is in an interval of 5−15 °C, and the draught rate is 15% or 25%, the actual mean vote and the predicted mean vote values differ significantly, and the actual mean vote is always lower, with a few exceptions. In addition,... [more]

The interconnection between optimal control theory and the theory of energy-shaping control is described in our paper. For linear and nonlinear systems, the application of the theory of optimal control for the synthesis of parameters of energy-shaping control matrices is demonstrated in detail. The use of a Riccati equation allows us to form an optimality criterion and to synthesize the energy-shaping control system that provides the desired transient processes. The proposed approach was applied to the synthesis of control influences for electric vehicle subsystems, such as a two-mass system and a permanent magnets synchronous motor. The results of computer simulation studies, as well as those conducted on real experimental installations, are given in this paper.

Underground mining engineers and planners in our country are faced with extremely difficult working conditions and a continuous shortage of money. Production disruptions are frequent and can sometimes last more than a week. During this time, gate road support is additionally exposed to rock stress and the result is its progressive deformation and the loss of functionality of gate roads. In such an environment, it is necessary to develop a low-cost methodology to maintain a gate road support system. For this purpose, we have developed a model consisting of two main phases. The first phase is related to support deformation monitoring, while the second phase is related to data analysis. To record support deformations over a defined time horizon we use laser scanning technology together with multivariate singular spectrum analysis to conduct data processing and forecasting. Fuzzy time series is applied to classify the intensity of displacements into several independent groups (clusters).

In this study, we present the wind distributions from a long-term offshore met mast and a novel approach based on the measure−correlate−predict (MCP) method from short-term onshore-wind-turbine data. The annual energy production (AEP) and capacity factors (CFs) of one onshore and four offshore wind-turbine generators (WTG) available on the market are evaluated on the basis of wind-distribution analysis from both the real met mast and the MCP method. Here, we also consider the power loss from a 4-month light detection and ranging (LiDAR) power-curve test on an onshore turbine to enhance the accuracy of further AEP and CF evaluations. The achieved Weibull distributions could efficiently represent the probability distribution of wind-speed variation, mean wind speed (MWS), and both the scale and shape parameters of Weibull distribution in Taiwan sites. The power-loss effect is also considered when calculating the AEPs and CFs of different WTGs. Successful offshore wind development require... [more]

Recently, issues related to the effects (benefit or harm) of processing nuclear waste and its further use as fuel have been increasingly often raised in the scientific discussion. In this regard, the research aims to investigate issues related to the assessment of the economic potential of nuclear waste use, as well as the cooperation between states in the context of the reduction of risks associated with nuclear waste storage and processing. The research methodology is based on an integrated approach, including statistical, factor analysis, and the proposed system of performance indicators for managing spent nuclear fuel use. The research was carried out on the basis of materials from Russia and the EU countries. In the course of the study, a model of cooperation between states has been developed (based on the example of technologies and methods of processing nuclear waste used in the EU and Russia) according to the nuclear waste (spent nuclear fuel) management algorithm. The model co... [more]

The combined operation of hybrid wind power and a battery energy storage system can be used to convert cheap valley energy to expensive peak energy, thus improving the economic benefits of wind farms. Considering the peak−valley electricity price, an optimization model of the economic benefits of a combined wind−storage system was developed. A charging/discharging strategy of the battery storage system was proposed to maximize the economic benefits of the combined wind−storage system based on the forecast wind power. The maximal economic benefits were obtained based on scenario analysis, taking into account the wind-power forecast error, and costs associated with the loss of battery life, battery operation, and maintenance. Case simulation results highlight the effectiveness of the proposed model. The results show that the hybrid wind−storage system is not only able to convert cheap electricity in the valley period into expensive electricity in the peak period, thus resulting in higher... [more]

South Africa has about 2.5 million households without electricity access, most of which are located in rural areas and urban informal settlements. The nexus of energy poverty and gender is at play in the affected communities, as women and girls are culturally stereotyped with the task of collecting unclean fuels (e.g., firewood) and using these for their households’ energy demands. Therefore, this study prioritized rural women and girls as respondents in the provinces most affected by gendered energy poverty (GEP) in the country. The study was carried out in selected rural unelectrified areas of Limpopo, Mpumalanga, and KwaZulu-Natal provinces using structured interviews. The study revealed that GEP in the rural areas has exposed women and girls living there to security concerns, health hazards, premature death, domestic fire accidents, time poverty, income poverty, illiteracy, drudgery in households and farm tasks, etc., at different levels of severity. It also showed the effects of p... [more]