The diagnostic fracture injection test (DFIT) is widely used to obtain the fracture closure pressure, reservoir permeability, and reservoir pressure. Conventional methods for analyzing DFIT are based on the assumption that a vertical well is drilled in ultra-low permeability reservoirs with potential multiple closures but fails to consider horizontal wells. There is still significant debate about the rigorousness and validity of these techniques due to the complexity of the hydraulic fracture opening and closure process and assumptions of conventional fracture detection methods. The paper introduces a new method for detecting fracture closure pressure using the continuous wavelet transform (CWT). The new method aims to decompose the pressure fall-off signal into multiple levels with different frequencies using the CWT. This “short wavy” function is stretched or compressed and placed at many positions along the signal to be analyzed. The wavelet then convoluted the signal yielding a wav... [more]

The main objective of this research is the study of the drying kinetics and thermodynamic properties of kelp using heat pump drying technology. The effects of the independent variables of temperature (20−50 °C), air velocity (0.3−1.3 m/s), humidity (20−50%), and thickness (0.8−4.2 mm) on the drying time, moisture uniformity, effective moisture diffusivity (Deff), activation energy (Ea), enthalpy (ΔH), entropy (ΔS), and Gibbs free energy (ΔG) were investigated. The results show that the Page model was effective in describing the moisture content change of kelp during heat pump drying. The Deff varied from 1.00 × 10−11 to 13.00 × 10−11 m2/s and the temperature, air velocity, humidity, and thickness had significant effects on drying time and moisture uniformity. Higher temperature and air velocity with proper humidity shortened the drying time and lessened the influence of thickness on moisture uniformity. The Ea (16.38−26.66 kJ/mol) and ΔH (13.69−24.22 kJ/mol) were significantly increase... [more]

This article deals with the influence of the final drying degree of moist biomass used as fuel in a power or CHP plant on indirect dryer sizing. For a description of the drying process, experiments with wet bark containing approx. 50 wt% of water were carried out in a laboratory indirect dryer. A new parameter called drying effectivity was introduced, whose size varies according to the degree of biomass being dried. Its maximum value corresponds to the optimal biomass drying, when the relative size of the indirect dryer to evaporate the required mass of water from the biomass would be smallest. Based on the experimentally determined drying characteristics of wet bark, the optimal drying of 13 wt% of water content was evaluated. If the bark was dried to a lower water content, the required relative size and price of the dryer would increase. Similarly, drying a bark with water content above 31 wt% is not very advantageous because drying effectivity continues to increase rapidly at this s... [more]

The depletion of fossil fuels has led to a search for new methods of fuel and chemical production from biomass. One of the methods of converting biomass into valuable products is the process of pyrolysis. This process has been extensively researched in recent years due to the rising prices of energy and chemicals. This work contains basic information on the pyrolysis process concerning the individual components present in the biomass and the types of biomass used in the pyrolysis process. Particular attention was paid to sewage sludge, the management of which is a big challenge. The influence of the most important process parameters (temperature, heating rate, residence time of the solid and vapor, reaction atmosphere) on the pyrolysis products (char, oil, and gas) was presented. The paper presents an overview of the reactors used in the pyrolysis process, from slow to fast pyrolysis, together with their efficiency, advantages, and disadvantages. The analysis of the application of othe... [more]

Over the past decade, there has been a great interest in the changeover from cars powered by gasoline to electric vehicles, both within the automotive industry and among customers. The electric vehicle−grid (V2G) technology is a noteworthy innovation that enables the battery of an electric vehicle during idling conditions or parked can function as an energy source that can store or release energy whenever required. This results in energy exchange between the grid and EV batteries. This article reviews various bidirectional converter topologies used in the V2G system. Additionally, it can reduce the cost of charging for electric utilities, thus increasing profits for EV owners. Normally electric grid and the battery of an electric vehicle can be connected through power electronic converters, especially a bidirectional converter, which allows power to flow in both directions. The majority of research work is carried out over the converters for V2G applications and concerns utilizing two... [more]

Conservation voltage reduction (CVR) is a potentially effective and efficient technique for inertia synthesis and frequency support in modern grids comprising power electronics (PE)-based components, aiming to improve dynamic stability. However, due to the complexities of PE-based grids, implementing the CVR methods cannot be performed using traditional techniques as in conventional power systems. Further, quantifying the CVR impacts in modern grids, while focusing on dynamic time scales, is critical, consequently making the traditional methods deficient. This is an important issue as CVR utilization/quantification depends on grid conditions and CVR applications. Considering these concerns, this work offers a thorough analysis of CVR applications, implementation, and quantification strategies, including data-driven AI-based methods in PE-based modern grids. To assess the CVR applications from a new perspective, aiming to choose the proper implementation and quantification techniques, t... [more]

Towards a carbon-neutral society, the building sector has a pivotal role with still a great potential for improvement. A new generation of buildings is rising but, to set a more ambitious shift in the paradigm and to fully justify the additional efforts (technological and economic) needed to fill the gap between net zero and plus energy performances, it is essential to consider not only the direct effects, but also all the indirect impacts. However, research conducted in the last decade solely focuses on the direct effects, mainly energy savings, while the indirect impacts neither have a clear identity nor terminology and a defined list of the impacts and methodologies for their quantification is still missing. With these premises, a systematic literature review on the current state of the art was performed in this work, with the aim of (i) investigating the heterogeneous terminology used for such indirect effects, (ii) identifying a final potential list of impacts both at the househol... [more]

In the process of development and utilization of a large-scale borehole heat exchanger (BHE) array system, the phenomenon of load shifting within BHE array can be observed. In this paper, OpenGeoSys software coupled with TESPy toolkit is used to establish a comprehensive numerical model of BHE system (without depicting the heat pump part), and the behaviors of load shifting between BHEs with different design parameters are studied. The results show that the outlet temperature of single BHE and BHE array is generally rising, and the soil temperature around the BHE has accumulated unbalanced heat. The soil temperature near the BHEs array fluctuates more obviously than the single BHE system, and the distribution is uneven. At the end of the 15th year, the soil temperature near the center BHE increased by 2 °C compared with the initial soil temperature, which was more favorable in winter, but was not conducive to the performance improvement in summer. Further analysis by changing the inter... [more]

New techniques and approaches are constantly being introduced to analyze and enhance the transient stability of renewable energy-source-dominated power systems. This review article extensively discusses recent papers that have proposed novel and innovative techniques for analyzing and enhancing the renewable source-dominated power system’s transient stability. The inherent low-inertia characteristics of renewable energy sources combined with fast-acting power electronic devices pose new challenges in power systems. Different stability concerns exist for grid-following and subsequent grid-forming converter/inverter connections to power grids; hence, distinct solutions for enhancing the transient stability have been devised for each. Moreover, the fundamental concepts and characteristics of converter/inverter topologies are briefly discussed in this study. Recent discussions and reviews of analysis and enhancement techniques in transient stability could lead to new ways to solve problems... [more]

Recycling used plastic can help reduce the amount of plastic waste generated. Existing methods, namely the process of pyrolysis, are chemical heating processes that decompose plastics in the absence of oxygen. This decomposes the plastics in a controlled environment in order to produce fuel from waste. The present study consequently investigated the physical and chemical properties of pyrolysis oil derived from plastic bottle caps (WPBCO) and the effects on the engine performance and emission characteristics of a diesel engine operating on WPBCO. The experiments were conducted with a single-cylinder diesel engine operating at a constant 1500 rpm under various engine loading conditions. The experimental results of the chemical properties of test fuels indicated that WPBCO and diesel fuels have similar functional groups and chemical components. In comparison, WPBCO has a lower kinematic viscosity, density, specific gravity, flash point, fire point, cetane index, and distillation behavior... [more]

Diesel engines play a very significant role in the automotive industry, but the total emissions of diesel engines are more than 1.8 times that of petrol engines. It is therefore important for diesel engines to control emissions. Theoretically, the Miller cycle can be used to achieve NOx reductions by changing the effective compression ratio, while it has become increasingly popular in recent years with the increasing maturity of current turbocharging technology. Based on Ricardo WAVE software, this paper analyses the NOx emissions and engine performance of diesel engines by modelling and simulating their operation under different loads with two types of Miller cycles (EIVC and LIVC) at different degrees. Simulation of engines operating under different loads allows a more comprehensive study of the effects of the Miller cycle on the engine, and a specific analysis in the context of the actual engine operating environment. The result is that both versions of the Miller cycle are most eff... [more]

Battery aging is one of the key challenges that electrochemical energy storage faces. Models for both cycling and calendar aging are valuable for quantitatively assessing their contribution to overall capacity loss. Since batteries are stored and employed under varying conditions of temperature and state of charge in their real-life operation, the availability of a suitable model to anticipate the outcome of calendar aging in lithium-ion batteries under dynamic conditions is of great interest. In this article, we extend a novel model to predict the capacity loss due to calendar aging by using variable-order fractional calculus. For this purpose, some theoretical difficulties posed by variable-order definitions are discussed and compared by applying them to fit experimental results with a multi-parameter optimization procedure. We show that employing a variable-order model allows for a significant improvement in accuracy and predictive ability with respect to its constant-order counterp... [more]

Hydrothermal carbonization (HTC) is an attractive, green technology for the management of sewage sludge. In this study, low-value secondary sewage sludge was subjected to an HTC treatment in a 1 L batch hydrothermal reactor and transformed into a high-energy-density hydrochar under varying HTC conditions (temperature of 150−300 °C, carbonization time of 30−150 min and a solid loading of 10−30%). The resulting hydrochar fuel characteristics were analyzed for ultimate and proximate analyses, functional group composition and energetic parameters. It was found that the hydrochar yield decreased with the increasing HTC temperature and reaction time, primarily due to the loss of organic volatile matter and functional groups. Under the optimum conditions of 150 °C, 30 min of carbonization time and 30% solid loading, 80.56% of the hydrochar was recovered, providing a maximum energy yield of 90.32% and a high heating value of 18.49 MJ/kg. Compared to the raw sewage sludge (H/C ratio of 2.67 and... [more]

Inorganic insulating powder can potentially be used in nuclear power plant cables, fire-resistant cables, and so on due to its high heat resistance and radiation resistance. It is of great academic and engineering value to study the dielectric properties of inorganic insulating powder. In this paper, we aim to study the nonlinear dielectric properties via the measurement of the time-domain polarization current spectrum under the application of a DC electric field. Three kinds of silica powders are measured by a measurement system with adjustable pressure. The effects of powder shape, particle size, and packing pressure and temperature on the dependence of relaxation polarization and electrical conductivity on the applied electric field are studied. The experimental results show that the relationship between electrical conductivity and the electric field of inorganic insulating powder presents two different characteristics, i.e., field-induced enhancement and field-induced weakening. Th... [more]

Extensive research has been conducted on energy storage systems (ESSs) for efficient power use to mitigate the problems of environmental pollution and resource depletion. Various batteries such as lead-acid batteries, lithium batteries, and vanadium redox flow batteries (VRFBs), which have longer life spans and better fire safety, have been actively researched. However, VRFBs undergo capacity reduction due to electrolyte crossover. Additionally, research on the capacity and state of charge (SOC) estimation for efficient energy management, safety, and life span management of VRFBs has been performed; however, the results of short-term experimental conditions with little change in capacity are presented without considering the rebalancing process of the electrolyte. Therefore, herein we propose a method for estimating the capacity of a VRFB using the cumulative charge and electrolyte volume amount under long-term cycle conditions, including rebalancing. The main point of the estimation m... [more]

Significant amounts of heat flow can be removed with small temperature differences by boiling. This process is used in a variety of industries, e.g., cooling electronics, digital circuits, power sources, etc. Heat dissipation from equipment that generates significant heat flows involves the movement of thermal energy through a wall into a cooling fluid. In the present study, this mechanism was analysed during the boiling of Novec-649 fluid at atmospheric pressure. The heat transfer surfaces were samples made of copper with milled, parallel grooves with a depth of 0.3 mm and a width ranging from 0.2 to 0.5 mm in 0.1 mm increments for straight channels and channels inclined with respect to the vertical by 30° and 60°, respectively. The study was carried out from the onset of nucleate boiling, approximately q = 7 kWm−2 with a heat flux increase until the critical heat flux was reached. The maximum heat flux was 262 kWm−2 and the heat transfer coefficient was 19.4 kWm−2K−1, achieved for su... [more]

Renewable electricity for off-grid areas is widely seen as one of the top choices in supporting local economic development in most countries, and so is Vietnam. Over the years, many isolated networks using renewable energy sources have been deployed for off-grid areas in Vietnam. However, the use of these energy sources in Vietnam’s isolated networks is still facing many challenges due to its infancy here. The issues of reliability and vulnerability of these networks are not given the expected attention. Another challenge is that the issues of the operational security of these systems could also be negatively affected by the variable nature of renewable sources, including static and dynamic security. For this reason, this study aims to contribute to a better understanding of integrating renewable energy into isolated networks, and in this case, using solar power for the An-Binh Island grid in Vietnam. The findings from this study suggest that choosing the right structure of the power m... [more]

Pump turbines play a quite important role of peak-valley shifting in the grid, and the hump margin is a critical criterion related to the safety and stability of operation in pump mode. Aiming at investigating the influence of runner outlet setting angle distribution on hump performance of a pump turbine, three runners with different linear distributions of setting angle at outlet were proposed, and the corresponding hump performance comparison was analyzed numerically through the SST k-ω turbulent model. The numerical result shows that, compared to the experiment, the relative errors of all simulated performances (energy characteristic, torque characteristic, and efficiency) were within 3%. Moreover, it was found that setting angle distribution modes could lead to a remarkably different performance in the hump region and, for the runner whose setting angle at shroud was 10° larger than that at hub, the hump safety margin could be increased from 4% to 4.5%. Thereafter, the correspondin... [more]

The decarbonisation of many sectors of the economy, including primarily the energy sector, results in the gradual elimination of hydrocarbon fuels, especially coal. During the transition period, it will be possible to use natural gas, the combustion of which is associated with lower carbon dioxide emissions. Further reduction in this emission is possible with the use of mixtures of natural gas with other gases, e.g., ammonia. Ammonia, widely used in many industries, has recently been described as the emission-free fuel of the future. However, both of these gases are hazardous substances. Natural gas is a flammable gas and ammonia is a toxic gas. This paper presents an assessment of the transport safety of natural gas (methane) and its mixture with ammonia. The uncontrolled release of these substances from a damaged gas pipeline may cause a fire or a toxic hazard. This work presents hazard zones arising in the event of such a failure and determines the impact of various mixture composit... [more]

Vertical-axis wind turbines (VAWTs) have a long history, with a wide variety of turbine archetypes that have been designed and tested since the 1970s. While few utility-scale VAWTs currently exist, the placement of the generator near the turbine base could make VAWTs advantageous over tradition horizontal-axis wind turbines for floating offshore wind applications via reduced platform costs and improved scaling potential. However, there are currently few numerical design and analysis tools available for VAWTs. One existing engineering toolset for aero-hydro-servo-elastic simulation of VAWTs is the Offshore Wind ENergy Simulator (OWENS), but its current modeling capability for floating systems is non-standard and not ideal. This article describes how OWENS has been coupled to several OpenFAST modules to update and improve modeling of floating offshore VAWTs and discusses the verification of these new capabilities and features. The results of the coupled OWENS verification test agree well... [more]

The dwindling and scarcity of fossil energy sources is the basis of the energy transition, where renewable resources are increasingly valued. The purpose of the cogeneration system studied in this article is to recover the residual heat from the gases coming out of the chimneys of the cement kilns, to produce at the same time the electricity and the heat required for offices and residential houses of cement workers. Cement kilns are reputed to be energy-intensive, generating excessive heat losses. These heat losses are found mainly in the conduction−convective and radiative modes, representing about 26% of the overall heat input to the system. Nevertheless, the gases at the chimney outlet can still have temperatures between 250 and 350 °C, which presents a non-negligible potential for a cogeneration system. This study compares the thermal performance of different cogeneration plant configurations (KCA, KCB, and KCC systems) using the Kalina cycle to determine the best one. Several assu... [more]

This article constitutes a relatively new perspective that has emerged from the need to reduce environmental pollution from internal combustion engine vehicles (ICEVs) by reinforcing the fleet of electric vehicles (EVs) on the road. Future requirements to exclusively use zero-emission vehicles have resulted in the necessity of enhancing the testing and monitoring process for EVs in order to release reliable devices. The unpredictable response of lithium-ion batteries (LIBS), future lack of raw materials, and inconsistencies in the present regulations must be reviewed and understood in order to develop enhanced batteries. This article aims to outline the future perspective of nonconventional vehicles monopolizing the roads by year 2035 in order to eradicate CO2 emissions by year 2050.

This paper investigates a cup-rotor permanent-magnet doubly fed machine (CRPM-DFM) for extended-range electric vehicles (EREVs). The topology and operating principle of the powertrain system based on CRPM-DFM are introduced. Then, the mathematical model of CRPM-DFM is established and the feedback linearization control of CRPM-DFM is given to realize the decoupling control of flux and torque. Moreover, the torque characteristic of CRPM-DFM is analyzed and the load torque boundaries with sinusoidal steady-state solution of CRPM-DFM is deduced. In addition, the MTPA control is derived to improve the efficiency of CRPM-DFM, and the efficiency of CRPM-DFM regarding various operating modes is investigated. Furthermore, the speed optimization strategy of ICE is proposed to reduce fuel consumption. Finally, the driving performance and fuel economy of the powertrain system are verified by simulation.

Many studies have shown that providing information on energy consumption to a household is effective, to some extent, in encouraging its energy conservation behavior. These studies provided information free of charge. However, depending on the type of information, a household must bear costs, such as installing the necessary equipment to obtain the information. Are people willing to pay for the information? In this study, a questionnaire survey was conducted to examine willingness to pay (WTP) for energy-related information using a choice experiment. The data were analyzed using conditional logit and latent class models. Positive WTP was estimated for information on the total energy consumption amount for the entire house, detailed electricity usage amount for each major home appliance, electricity rates by time zone, and power source composition of electricity. No significant positive results were obtained for comparison with the other households, as the class that accounted for about... [more]

In this study, the microencapsulation-hybrid jig separation technique was developed to improve the separation efficiency of pyrite and coal in the particle size range of 1−4 mm where conventional jig separation becomes inefficient. A hybrid jig is a gravity concentrator combining the concepts of jig separation and flotation to stratify particles based on their apparent specific gravity. Meanwhile, microencapsulation—a technique that encapsulates target materials with a protective coating—was applied to render pyrite hydrophilic and improve its separation from hydrophobic coal. The results showed that the required time for separation in the hybrid jig (0.5 min) was shorter than in conventional jig (2 min). Moreover, the effects of particle size on separation efficiency were reduced when a hybrid jig is used. However, the separation efficiency of hybrid jig separation was lower than that of the conventional jig because attachment of bubbles occurred to both pyrite and coal, which are hyd... [more]