Environmental concerns over automotive exhaust emissions and consumer demand for higher fuel efficiency have led to the development of low-temperature combustion concepts. The reactivity-controlled compression ignition (RCCI) engine is one among them and has the potential to reduce NOx and smoke emissions simultaneously. In this concept, a low-reactivity fuel is injected into the intake port and another high-reactivity fuel is injected into the cylinder directly. This results in reactivity stratification and provides more control over the rate of heat release. However, operating parameters such as reactivity of fuels, premixing ratio, injection strategies, exhaust gas recirculation ratio, piston bowl geometry, and compression ratio influence emissions formation. The article reviews recent developments on the effect of the above operating parameters on the performance and emission characteristics of RCCI engines operated with alternative fuels. The combustion strategies used to extend t... [more]

The electric mode is the main operational mode of dual-motor hybrid electric vehicles (HEVs), so the reliability of the dual-motor electric drive system (DEDS) is particularly important. To research the electromechanical coupling mechanism of the DEDS of HEVs, firstly, considering the time-varying mesh stiffness of gears and the nonlinear characteristics of inverters, an electromechanical coupling dynamics model of the DEDS was established, including the permanent magnet synchronous motor (PMSM) and the gear transmission system. Then, the electromechanical coupled dynamic characteristics of the DEDS in the single-motor and dual-motor drive modes were analyzed under steady-state and impact load conditions, respectively. The results show that the motor stator current frequency is modulated by the complicated gear meshing frequency, and the operation state of the gear transmission system can thus be monitored in the stator current. Impact load causes the instantaneous torsional vibration... [more]

Nano fluids are widely used today for various energy-related applications such as coolants, refrigerants, and fuel additives. New coolants and design modifications are being explored due to renewed interest in improving the working fluid properties of heat exchangers. Several studies have investigated nanofluids to enhance radiator and heat exchanger performance. A new class of coolants includes single, binary, and tertiary nanoparticle-based hybrid nano-coolants using ethylene glycol/deionized water combinations as base fluids infused with different nanoparticles. This review article focuses on the hydrothermal behavior of heat exchangers (radiators for engine applications) with mono/hybrid nanofluids. The first part of the review focuses on the preparation of hybrid nanofluids, highlighting the working fluid properties such as density, viscosity, specific heat, and thermal conductivity. The second part discusses innovative methodologies adopted for accomplishing higher heat transfer... [more]

This review provides the state of the art of energy management systems (EMS) and organizational structures of prosumers. Integration of renewable energy sources (RES) into the household brings new challenges in optimal operation, power quality, participation in the electricity market and power system stability. A common solution to these challenges is to develop an EMS with different prosumer organizational structures. EMS development is a multidisciplinary process that needs to involve several aspects of observation. This paper provides an overview of the prosumer organizational and control structures, types and elements, prediction methods of input parameters, optimization frameworks, optimization methods, objective functions, constraints and the market environment. Special attention is given to the optimization framework and prediction of input parameters, which represents room for improvement, that mitigate the impact of uncertainties associated with RES-based generation, consumpti... [more]

Contemporary megawatt-scale data centers have emerged to meet the increasing demand for online cloud services and big data analytics. However, in such large-scale data centers, servers of different generations are installed gradually year by year, making the data center heterogeneous in computing capability and energy efficiency. Furthermore, due to different processor architectures, complex and diverse load dynamic changing, business coupling, and other reasons, operators pay great attention to processor hardware power consumption and server aggregation energy efficiency. Therefore, the simulation and analysis of the energy efficiency characteristics of data center servers under different processor architectures can help operators understand the energy efficiency characteristics of data centers and make the optimal task scheduling strategy. This is very beneficial for improving the energy efficiency of the production system and the entire data center. The Escope simulator designed in... [more]

The present study investigates the steady three-dimensional flow of a Sisko fluid over a bidirectional stretching sheet under the influence of Lorentz force. Heat transfer effects have been carried out for constant heat flux and Newtonian heating systems. The transformed governing equations of the flow model are solved by using the spectral relaxation method (SRM), taking into account similarity transformations. The effects of controlling parameters on flow and derived quantities have been presented in the form of graphs and tables. Numerical benchmarks are used to characterise the effects of skin friction and heat transfer rates. It is noticed that in the case of Newtonian heating, the rate of heat transfer is higher than that in the constant heat flux case. As the stretching parameter increases, the fluid temperature decreases in both Newtonian heating and constant heat flux. It was discovered that successive over (under) relaxation (SOR) approaches will considerably boost the conver... [more]

Determining the operation scenarios of renewable energies is important for power system dispatching. This paper proposes a renewable scenario generation method based on the hybrid genetic algorithm with variable chromosome length (HGAVCL). The discrete wavelet transform (DWT) is used to divide the original data into linear and fluctuant parts according to the length of time scales. The HGAVCL is designed to optimally divide the linear part into different time sections. Additionally, each time section is described by the autoregressive integrated moving average (ARIMA) model. With the consideration of temporal correlation, the Copula joint probability density function is established to model the fluctuant part. Based on the attained ARIMA model and joint probability density function, a number of data are generated by the Monte Carlo method, and the time autocorrelation, average offset rate, and climbing similarity indexes are established to assess the data quality of generated scenarios... [more]

Recently, water desalination (WD) has been required for the supply of drinking water in a number of countries. Various technologies of WD utilize considerable thermal and/or electrical energies for removing undesirable salts. Desalination systems now rely on renewable energy resources (RERs) such as geothermal, solar, tidal, wind power, etc. The intermittent nature and changeable intensity constrain the wide applications of renewable energy, so the combination of energy storage systems (ESSs) with WD in many locations has been introduced. Thermal energy storage (TES) needs a convenient medium for storing and hence reuses energy. The present work provides a good background on the methods and technologies of WD. Furthermore, the concepts of both thermal and electrical energy storage are presented. In addition, a detailed review of employing ESSs in various WD processes driven by RERs is presented. The integration of energy storage with water desalination systems (WDSs) based on renewable... [more]

Due to microscale effects, the segmented microchannels or micro pin fin heat sinks emerged as a high thermal management solution. In this context, the present work analyzes the influence of different heights of square micro pin fins with an aligned array and investigates their influence on pressure drop and heat transfer behavior. The HFE-7100 is used as the working fluid, and the pressure drop and surface temperature behavior are analyzed for different mass fluxes and inlet subcooling. The single-phase flow was analyzed numerically using the computational fluid dynamics (CFD) software ANSYS FLUENT® for comparing the simulation results with the experimental data, showing that the highest micro pin fins configuration provides a more uniform and lowest wall temperature distribution compared to the lowest configuration. There is a good agreement between the experimental results and the numerical analysis, with a mean absolute error of 6% for all the considered parameters. For the two-phas... [more]

The present study presents a numerical prediction of residual stresses (RS) using the single-pass tungsten inert gas (TIG) welding process for stainless steel plates and the two-pass TIG welding process for stainless steel pipes. The effect of heat exchange between welding material and the environment was studied. The work consists of two parts: The first one is based on the determination of the existence of residual stresses numerically using Cast3M software, which has been validated by literature results. The second part addresses the means envisaged to attenuate the amplitudes of these residual stresses by practical methods. Two parameters with significant influence on the residual stresses have been chosen: the welding bead thickness and the torch displacement speed. The finite element model used has been validated experimentally, and the results obtained for the residual stresses have been compared with those given by the numerical study. The results obtained were found to be in a... [more]

In coal mine goafs, spontaneous combustion of coal can result in methane accumulation, which raises the danger of methane explosion disasters. As an atmospheric control tool, ventilation is applied to ensure air quality for avoiding disasters in underground mines. However, during the process of the spontaneous combustion of coal in coal mine goafs, the impact of ventilation dilution on the possible methane explosions induced by coal combustion has not been well investigated. In this study, a validated gas flow model for the spontaneous coal combustion environment in goafs of coal mines is adopted to investigate the influence of ventilation dilution at the three stages of the spontaneous combustion of coal. The research conclusions suggest that (1) ventilation dilution is a quick measure to dilute methane concentration and intensify heat transfer in the vertical direction in coal mine goafs; (2) ventilation dilution can lessen the danger of methane explosions by diluting methane concent... [more]

Sodium-ion batteries (SIBs) are one of the recent trends in energy storage systems due to their promising properties, the high abundance of sodium in the Earth’s crust, and their low cost. However, the commercialization process of SIBs is in the early stages of development because of some challenges related to electrodes and electrolytes. Electrolytes are vital components of secondary batteries because they determine anode/cathode performance; energy density; operating conditions (electrochemical stability window, open circuit voltage, current rate, etc.); cyclic properties; electrochemical, thermal, mechanical, and dimensional stability; safety level; and the service life of the system. The performance of the battery is based on the structural, morphological, electrical, and electrochemical properties of the electrolytes. In this review, electrolytes used for SIBs are classified according to their state and material, including liquid, quasi-solid, solid, and hybrid, and recent advance... [more]

A novel linear permanent magnet vernier generator (LPMVG) for small-power off-grid wave power generation systems is proposed in this paper. Firstly, in order to reduce the cogging force and the inherent edge effect of the linear generator, a staggered tooth modular structure is proposed. Secondly, in order to improve the output power and efficiency of the LPMVG and reduce the fluctuation coefficient of electromagnetic force, the relationship between the parameters of the generator is studied, and a method combining multi-objective optimization and single parameter scanning based on the response surface model and particle swarm optimization algorithm is proposed to obtain the optimal structural parameters of the generator. Thirdly, the output power and efficiency of the optimized generator are calculated and analyzed based on the two-dimensional finite element method, and the effectiveness of the multi-objective optimization design method based on the response surface model and particle... [more]

In this study, we investigated the acid (HCl) and alkali (KOH) chemical activation of açaí seeds (Euterpe Oleraceae, Mart.) pre-treatment before pyrolysis at temperatures of 350−450 °C in order to assess how reactions proceed when affected by temperature. Chemical composition of bio-oil and aqueous phase were determined by GC-MS and FT-IR. The bio-char is characterized by XRD. For the activation with KOH, the XRD analysis identified the presence of Kalicinite (KHCO3), the dominant crystalline phase in bio-char, while an amorphous phase was identified in bio-chars for the activation with HCl. The experiments have shown that bio-oil yield increases with temperature for the KOH activated biomass and decreases for the acid activated one. The KOH bio-oil is primarily composed of alcohols and ketones, showing the lowest acid values when compared with the HCl one, which is composed mainly of carboxylic acids and phenols. An increase in alcohol content and a decrease in ketones in the KOH bio-... [more]

The most common fuel used for powering compression ignition engines is diesel, whose main components are petroleum products. The constantly growing energy demand involves the implementation of new technical solutions and applying alternative fuels, including renewable ones, such as rapeseed oil, sunflower oil, peanut oil, and animal fats. The most commonly used biofuels are those obtained from chemically processed rapeseeds (transesterification) to provide them with physical−chemical properties similar to diesel fuel. The study presents the results of tests of a power unit fueled with different mixtures of diesel oil and fatty acid methyl esters. The experiment was carried out for a compression ignition engine of 81 kW power with direct fuel injection. Performance parameters of the vehicle power unit and its computer software were modified for the needs of the tests. Those modifications involved increasing the fuel dose and the fuel injection pressure. The test results were statistical... [more]

In ship systems, diesel power generators are used in various systems of autonomous power plants to ensure power supply security. This article presents an autonomous hybrid system of a ship power plant with a diesel generator with a permanent magnet synchronous generator and electricity storage in parallel topology (the permanent magnet synchronous generator is connected directly to the receiving network). The electricity storage through the active converter is connected to the receiving network in parallel with the permanent magnet synchronous generator. The decoupled control of the reactive and active power in the active converter enables stabilization of the voltage in the ship’s electrical power grid while ensuring the possibility of obtaining different operating regimes of the power plant at various stages of the ship’s operation. The innovative method of voltage stabilization presented in this article is based on the compensation of the unfavorable reaction of the permanent magnet... [more]

In 2021, there was a global energy crisis that affected different parts of the world. In most countries, energy heavily relies on natural gas, including Nigeria, India, and Bangladesh. Several studies have explored the differences in the energy of crude oil and natural gas. Nonetheless, little effort has been made toward exploring the exportation of energy for exchange markets in Nigeria, India, and Bangladesh. This paper primarily aims at comparatively exploring the energy of crude oil and natural gas for exchange markets in the aforementioned countries. The methodology used in this paper is qualitative content analysis (QCA) and a systematical literature review (SLR) which includes various sources such as journals, the core collection of the Web of Science (WOS), oil peer review resources, and library sources. The study systematically mapped out different bibliographic materials whereby the visualization of similarities (VOS) was used to explore exchange markets for energy, crude oil... [more]

Plug-in electric vehicles (PEVs) and distributed generation (DG) can positively and negatively impact the distribution system. Therefore, this paper presents the modeling and analysis of DG and PEVs’ penetration levels of the three-phase unbalanced radial distribution system. The study aims to optimize the distribution system’s DG sizing and PEV charging to minimize total power loss. The test system is the 4th circuit of the Nonsung service station along Thaharn Road, Muang District, Udon Thani, Thailand. According to objective function and constraints, such control variables as installation buses and rated outputs of DG and the penetration levels of PEVs were obtained to evaluate the total power loss. Significantly, the charging demand of PEVs is an uncertain load estimated by queuing theory integration with the minimization tool called the differential evaluation (DE) method. According to the result comparison of a four case simulation, the total power losses of queuing theory and DE... [more]

Today, increasing numbers of batteries are installed in residential and commercial buildings; by coordinating their operation, it is possible to favor both the exploitation of renewable sources and the safe operation of electricity grids. However, how can this multitude of battery storage systems be coordinated? Using the Application Programming Interfaces of the storage systems’ manufacturers is a feasible solution, but it has a huge limitation: communication to and from storage systems must necessarily pass through the manufacturers’ cloud infrastructure. Therefore, this article presents an IoT-based solution which allows monitoring/controlling battery storage systems, independently from the manufacturers’ cloud infrastructure. More specifically, a home gateway locally controls the battery storage using local APIs via Wi-Fi on the condition that the manufacturer enables them. If not, an auxiliary device allows the home gateway to establish a wired communication with the battery stora... [more]

Renewable energy sources (RESs) and electricity demand are not evenly distributed geographically across Europe. Thus, harvesting the wind energy from the north and solar energy from the south and delivering them to the demand in central Europe is a more viable solution. However, the present High-voltage alternating current (HVAC) transmission grids have been sometimes congested; thus, High-voltage direct current (HVDC) provides another possibility along the existing HVAC infrastructure. In this paper, we propose a hybrid HVAC-HVDC grid, allowing a large penetration of concentrated RES in Europe and North Africa. More specifically, the HVDC network is constructed to transfer wind and hydro electricity from northwestern Europe and solar electricity from north Africa, while the HVAC network is used to distribute electricity within each country or among adjacent areas. To quantitatively evaluate the feasibility and relevant performances, multiple dimensions of indicators are designed. Empl... [more]

In this study, we developed a 3D-model-based technology that can evaluate solar access by analyzing solar radiation and shade to find the optimal location for a solar system. We developed an algorithm that can quickly calculate viewshed by applying ray-casting technology, which is useful in the field of computer graphics. To apply the developed technology, an unmanned aerial vehicle (DJI MAVIC 3) was used to create a 3D model by taking 320 photos of the Kangwon National University Samcheok campus. To verify the developed technology, a comparison with image-based analysis using a 360-degree camera was performed for 30 points. As a result of applying the developed technology to the study area, it was possible to calculate the solar access for each point. In general, image-based analysis exaggerates the effects of objects such as trees, whereas the developed technique can produce realistic results if the 3D objects were well built. If the technology is further developed in the future, it... [more]

This study examines the dynamic connection between green energy, employment, fossil fuel energy, and human development index including additional variables such as education, life expectancy, and poverty in panel data of 30 developing countries from 1990−2017. Previous studies analyzed the total energy consumption on the human development index, whereas the differential effect of green and fossil fuel energy with employment and human development index has not been examined. The empirical exercise is based on the panel co-integration test, panel fully modified ordinary least squares, dynamic ordinary least squares, and vector error correction estimation approaches. The results reveal that all variables are co-integrated. The results of regression analysis indicate that green energy, education, life expectancy, and employment increase the human development index, but fossil fuel energy and poverty decrease the human development index by −0.016 and 0.023%. In addition, the vector error co... [more]

To solve problems related to global warming, environmental pollution, and green energy fields, a lot of research is now devoted to the catalysis of biofuels and biogas transformation into syngas and hydrogen [...]

This article describes the hydrocarbon reserves in the oil and gas provinces of Russia’s Arctic territory, as well as specific features of the region’s raw hydrocarbon potential. It has been noted that the implementation of Arctic hydrocarbon-associated projects requires that a unified transport and logistics system be created, with the Northern Sea Route being the basis. The factors affecting the volume of cargo transportation along the Arctic routes are presented. It has been established that the hydrocarbon extraction and liquefied natural gas production in the Russian Arctic zone is the most important factor in the formation of cargo flows along the Northern Sea Route. The most significant oil and gas projects that comprise the bulk of freight traffic flow along the Arctic transportation corridors have been reviewed. The ports, as the main element of the Arctic transport system, are described in terms of their state and infrastructure. It has been indicated that the construction, m... [more]

There is a significant energy transition in progress globally. This is mainly driven by the insertion of variable sources of energy, such as wind and solar power. To guarantee that the supply of energy meets its demand, energy storage technologies will play an important role in integrating these intermittent energy sources. Daily energy storage can be provided by batteries. However, there is still no technology that can provide weekly, monthly and seasonal energy storage services where pumped hydro storage is not a viable solution. Herein, we introduce an innovative energy storage proposal based on isothermal air compression/decompression and storage of the compressed air in the deep sea. Isothermal deep ocean compressed air energy storage (IDO-CAES) is estimated to cost from 1500 to 3000 USD/kW for installed capacity and 1 to 10 USD/kWh for energy storage. IDO-CAES should complement batteries, providing weekly, monthly and seasonal energy storage cycles in future sustainable energy gr... [more]