The SARS-CoV-2 pandemic has resulted in the need for increased surface disinfection. For this purpose, biocides, UV-C radiation, or ozonation can be used. The most commonly used are biocides that can be deposited on the surface with the use of various devices, including foggers. The disinfection efficiency is related to the size of the aerosol droplets formed and their distribution. This paper specifies the distribution of droplet diameters and mean droplet diameters obtained during the use of a commercial fogger. It was shown that the droplet diameters formed were mainly in the range of up to 30−40 μm. A ceramic filter allowed for a larger number of smaller droplets and a limitation in the number of droplets with larger diameters. The results are important in the context of fighting the virus in hard-to-reach places where battery devices can be used.

There are some environmental factors, such as ambient temperature, dust, etc., which cause a reduction in the efficiency of Photovoltaic (PV) systems. Installation of PV panels on the water surface, commonly known as Floating Photovoltaic (FPV) systems, is one solution to employ PV panels in a cooler environment, achieve higher efficiency, and reduce water evaporation. FPV systems open up new opportunities for scaling up solar generating capacity, especially in countries with high population density and valuable lands, as well as countries with high evaporation rates and water resources deficiency. Since the FPV system is an almost new concept, its cleaning techniques have not been comprehensively studied. While FPV systems are located on the surface of water resources and reservoirs, the water quality can limit the application of different cleaning techniques. Therefore, this paper investigates different techniques of FPV systems cleaning and categorizes them into water-based and wate... [more]

A diesel engine is a typical dynamic system. In this paper, a dynamics method is proposed to establish the Hamiltonian model of the diesel engine, which solves the main difficulty of constructing a Hamiltonian function under the multi-field coupling condition. Furthermore, the control method of Hamiltonian model structure modification is introduced to study the control of a diesel engine. By means of the principle of energy-shaping and Hamiltonian model structure modification theories, the modified energy function is constructed, which is proved to be a quasi-Lyapunov function of the closed-loop system. Finally, the control laws are derived, and the simulations are carried out. The study reveals the dynamic mechanism of diesel engine operation and control and provides a new way to research the modeling and control of a diesel engine system.

The paper is focused on numerical modeling of multi-strand cable lines placed in free air. Modeling is carried out within the framework of the so-called multi-physics approach using commercial software. The paper describes in detail the steps undertaken to develop realistic, reliable numerical models of power engineering cables, taking into account their geometries and heat exchange conditions. The results might be of interest to the designers of multi-strand cable systems.

Maximum power point tracking (MPPT) algorithms are invariably employed to utilize solar photovoltaic (PV) systems effectively. Perturbation based MPPT algorithms are popular due to their simplicity and reasonable efficiency. While novel MPPT algorithms claim increased energy utilization over classic perturbation techniques, their performance is governed by the choice of optimal algorithm parameters. Existing guidelines for parameter optimization are mathematically laborious and are not generic. Hence, this paper aims to provide simple and comprehensive guidelines to ensure optimal performance from the perturbation based MPPT technique. For an illustration of proposed claims, a solar PV fed boost converter is investigated to examine the effect of input capacitor, digital filter cut-off frequency, system time constant and sampling time on implementing a classic Perturb and Observe (P and O) algorithm. The readers will be presented with two simple step tests (to determine the effective sy... [more]

In this study, the combustion characteristics and emission of toxic gases of a non-class 1E cable in a nuclear power plant were investigated with respect to the aging period. A thermal accelerated aging method was applied using the Arrhenius equation with the activation energy of the cables and the aging periods of the cables set to zero, 10, 20, 30 and 40 years old by considering the lifetime of a nuclear power plant. According to ISO 5660-1 and ISO 19702, the cone calorimeter Fourier transform infrared spectroscopy test was performed to analyze the combustion characteristics and emission toxicity. In addition, scanning electron microscopy and an energy dispersive X-ray spectrometer were used to examine the change in the surface of the sheath and insulation of the cables according to the aging periods. To compare quantitative fire risks at an early period, the fire performance index (FPI) and fire growth index (FGI) are derived from the test results of the ignition time, peak heat rel... [more]

In recent years, the steel-truss natural draft dry cooling technique has received attention owing to its advantages in better aseismic capability, shorter construction period, and preferable recycling. For cooling towers generating the draft force of air flow, its configuration may impact the thermal and flow performance of the steel-truss natural draft dry cooling system. With regard to the issue, this work explored the thermal and flow characteristics for the steel-truss natural draft dry cooling systems with four typical engineering tower configurations. By numerical simulation, the pressure, flow, and temperature contours were analyzed, then air mass flow rates and heat rejections were calculated and compared for the local air-cooled sectors and overall steel-truss natural draft dry cooling systems with those four tower configurations. The results present that tower 2 with the conical/cylindrical configuration had slightly lower heat rejection compared with tower 1 with the traditi... [more]

Carbon included in coke and coal was used as a reduction agent and fuel in blast furnace (BF) ironmaking processes, which released large quantities of carbon dioxide (CO2). Minimizing the carbon consumption and CO2 output has always the goal of ironmaking research. In this paper, the reduction reactions of iron oxides by carbon, the gasification reaction of carbon by CO2, and the coupling reactions were studied by thermodynamic functions, which were derived from isobaric specific heat capacity. The reaction enthalpy at 298 K could not represent the heat value at the other reaction temperature, so the certain temperature should be confirmed by Gibbs frees energy and gas partial pressure. Based on Hess’ law, the energy consumption of the ironmaking process by carbon was calculated in detail. The decrease in the reduction temperature of solid metal iron has been beneficial in reducing the sensible heat required. When the volume ratio of CO to CO2 in the top gas of the furnace was given as... [more]

Today’s offshore wind turbine support structures market is largely dominated by steel structures, since steel monopiles account for the vast majority of installations in the last decade and new types of multi-leg steel structures have been developed in recent years. However, as wind turbines become bigger, and potential sites for offshore wind farms are located in ever deeper waters and ever further from the shore, the conditions for the design, transport, and installation of support structures are changing. In light of these facts, this paper identifies and categorizes the challenges and future trends related to the use of concrete for support structures of future offshore wind projects. To do so, recent advances and technologies still under development for both bottom-fixed and floating concrete support structures have been reviewed. It was found that these new developments meet the challenges associated with the use of concrete support structures, as they will allow the production c... [more]

The European Union Green Deal aims at curbing greenhouse gas emissions and introducing clean energy production. But to achieve energy efficiency, the opportunity cost of different energies must be assessed. In this article, two different energy self-sufficient systems for wastewater treatment are compared. On the one hand, high-rate algal ponds system (HRAP) is considered; on the other hand, a conventional activated sludge system (AS) which uses photovoltaic power (PV) is studied. The paper offers a viability analysis of both systems based on the capacity to satisfy their energetic consumption. This viability analysis, along with the opportunity cost study, will be used in the article to compare these two projects devoted to the treatment of wastewater. In order to assess viability, the probability of not achieving the energy consumption threshold at least one day is studied. The results point that the AS+PV system self-sufficiency is achieved with much lesser land requirements than th... [more]

This paper deals with a discrete-time stochastic control model design for random failure prone and maintenance in a single machine infinite bus (SMIB) system. This model includes the practical values of failure/repair rate of transmission lines and transformers. The probability matrix is, therefore, calculated accordingly. The model considers two extreme modes of operations: the most reliable mode and the least reliable contingency case. This allows the control design which stochastically stabilizes the system under jump Markov disturbances. For adequate transient response, the proposed state feedback power system stabilizer (PSS) achieves a desired settling time and damping ratio by placing the closed-loop poles in a desired region. The control target should also be satisfied for load variations in either mode of operation. A sufficient condition is developed to achieve the control objectives via solving a set of linear matrix inequalities (LMI). Using simulation, the performance of t... [more]

Electricity supply in nonelectrified areas can be covered by distributed renewable energy systems. The main disadvantage of these systems is the intermittent and often unpredictable nature of renewable energy sources. Moreover, the temporal distribution of renewable energy may not match that of energy demand. Systems that combine photovoltaic modules with electrical energy storage (EES) can eliminate the above disadvantages. However, the adoption of such solutions is often financially prohibitive. Therefore, all parameters that lead to a functionally reliable and self-sufficient power generation system should be carefully considered during the design phase of such systems. This study proposes a sizing method for off-grid electrification systems consisting of photovoltaics (PV), batteries, and a diesel generator set. The method is based on the optimal number of PV panels and battery energy capacity whilst minimizing the levelized cost of electricity (LCOE) for a period of 25 years. Vali... [more]

Gasification is considered a clean and effective way to convert low quality biomass to higher value gas and solve various waste utilization problems as well. However, only 80% of biomass is converted through thermal processes. The remaining part is char, which requires more time for conversion and in that case reduces the efficiency of gasifier. Seeking to optimize the process of gasification, this work focuses on the intensification of residual char gasification in a gasifier. For this purpose, three different types of char prepared from wood, sewage sludge and tire were examined under different conditions in a lab-scale gasification setup. Results showed that the air flux increase from 0.11 kg/(m2s) to 0.32 kg/(m2s) intensified the gasification process and the gasification rate increased from 0.8 to 2.61 g/min with the decrease of duration of wood char gasification by 72%. An additional introduction of pyrolysis gas into the char gasifier led to decreased bed temperatures, but the ga... [more]

This study comprehensively analyzed the heat loss and total heat transfer coefficient (U-value) of a single-span experimental plastic greenhouse covered with a double layer of 0.1 mm thick polyethylene. The air temperature and heat flux (W m−2) of the greenhouse components were measured from 18:00 to 06:00, and the energy balance equations under steady-state conditions were determined. The heat flux and U-value of the roof, sides, front and rear, and floor of the greenhouse were determined and compared. The results showed that these values for the roof play an important role in determining the heat load in the greenhouse, and that the average heat transfer through the floor is very small. The average U-value of the greenhouse cover is a comprehensive value which takes the U-values of the roof, sides, and front and rear into account through the use of an area−weighted average method. Finally, an average U-value of 3.69 W m−2 °C −1 was obtained through the analysis of the variations in t... [more]

Direct Current (DC) grids are considered an attractive option for integrating high shares of renewable energy sources in the electrical distribution grid. Hence, in the future, Alternating Current (AC) and DC systems could be interconnected to form hybrid AC-DC distribution grids. This paper presents a two-step state estimation formulation for the monitoring of hybrid AC-DC grids. In the first step, state estimation is executed independently for the AC and DC areas of the distribution system. The second step refines the estimation results by exchanging boundary quantities at the AC-DC converters. To this purpose, the modulation index and phase angle control of the AC-DC converters are integrated into the second step of the proposed state estimation formulation. This allows providing additional inputs to the state estimation algorithm, which eventually leads to improve the accuracy of the state estimation results. Simulations on a sample AC-DC distribution grid are performed to highligh... [more]

Strategic and tactical factors come into play in shop competitiveness where, in addition to the products sold, other marketing mix variables must also be considered. There are also subjective factors, such as perceptions through the senses. This became even more important when, as a result of the COVID-19 crisis and the forced closure of certain establishments with physical sales, it was necessary to increase profitability and efficiency. The aim of this study was to determine the exact role of sensory marketing in shop efficiency and profitability, based on the guiding principles of technology, innovation, and respect for the environment. We conducted an exploratory and experimental study consisting of the creation of a sensory strategy through the adaptation of the Hulten, Broweus and Van Dijk model on a specific establishment in the current era of Industry 4.0. The results indicate an increase in sales as well as customer satisfaction and happiness after implementing the relevant st... [more]

The automotive industry has been rapidly transforming and moving further from internal combustion engines, towards hybrid or electric vehicles. A key component for the successful adoption of the aforementioned approach is their Energy Management Systems (EMSs). In the proposed work, we describe in detail a custom EMS, with unique characteristics, which was developed and installed in a hydrogen-powered prototype vehicle. The development of the EMS was based on off-the-shelf components and the adoption of a Robot Operating System (ROS), a meta-operating system developed for robotic-oriented applications. Our approach offers soft real-time control and the ability to organize the controller of the EMS as a straightforward and comprehensive message system that provides the necessary inter-process communication at the core of the EMS control procedure. We describe in detail the software-based implementation and validate our approach through experimental results obtained while the prototype w... [more]

Increasing energy demand and environmental regulations around the world provide an adequate framework for developing methods of obtaining energy from renewable sources. Wind force is a resource with a high potential through which green energy can be obtained with no negative impact on the environment. Different turbine typologies have been developed, which can convert the wind force into mechanical and electrical energy through turbine rotational motion. Starting from the classic vertical-axis SAVONIUS rotor model, other models have been designed, which, according to the numerical studies and experimental test results, show higher performance parameters in operation. Such models present specific rotor blade geometries to achieve better operational results in terms of shaft torque and generated power. There are multiple research results from numerical analysis on virtual models or experimental tests that use rotor models in different constructive configurations aiming to improve operati... [more]

In adsorption heat pumps, the adsorbent is typically combined with heat conducting structures in order to ensure high power output. A new approach for the direct integration of zeolite granules into a copper structure made of short copper fibers is presented here. Zeolite NaY granules with two different grain sizes are coated with copper fibers and powder and sintered to larger structures. The sorption dynamics of these structures were measured and evaluated in terms of heat and mass transfer resistances and compared to the loose grain configuration of the same material. We found that the thermal conductivity of such a composite structure is approximately 10 times higher than the thermal conductivity of an adsorbent bed with NaY granules. Sorption equilibrium measurements with a volumetric method indicate that the maximum uptake is not altered by the manufacturing process. Furthermore, the impact of the adsorbent−metal structure on the total thermal mass of an adsorption heat exchanger... [more]

Natural gas (NG) engines have very broad application prospects. The pilot-ignited NG diesel engine can be organized into two combustion modes according to the sequence of oil and gas injection: (1) High-pressure direct injection, where NG is mainly diffused combustion; and (2) partially premixed compression ignition, where NG is mainly premixed combustion. In this study, we used CONVERGE to explore the influence of the NG injection timing on the distribution of the mixture equivalence ratio, ignition characteristics, thermal efficiency, emission, and combustion reaction rate under the two combustion modes. We also used a multi-step soot model to analyze the particle mass and quantity. We showed herein that the NG injection timing significantly affects the mixture distribution in the cylinder, thereby consequently affecting the combustion process. Both very early and very late injection times were not conducive to NG combustion. In addition, the mass, quantity, and diameter of the soot... [more]

Perovskite solar cells have progressed very steadily, reaching power conversion efficiencies (PCE) beyond 20% while also improving their lifetimes up to 10,000 h. A large number of cell architecture and materials for active, transporting and electrode layers have been used, either in blends or in nanostructured layers. In this article, a set of perovskite solar cells have been designed, fabricated and characterized with special focus on their lifetime extension. The inclusion of 5-amino-valeric acid iodide (5−AVAI) as interlayer in a methyl-amino lead-iodide (MAPI) perovskite solar cell has provided additional stability in cells with PCE > 10% and T80 = 550 h. Experiments for up to 1000 h with solar cells at maximum power point under continuous illumination with solar simulator have been carried out (1 kW/m2, AM1.5G, equivalent to more than six months of outdoor illumination in locations such as Southeast Spain, with an average irradiation of 1900 kWh/m2/year). The addition of molecula... [more]

Innovative vehicle concepts have been developed in the past years in the automotive sector, including alternative drive systems such as hybrid and battery electric vehicles, so as to meet the environmental targets and cope with the increasingly stringent emissions regulations. The preferred hybridizing technology is lithium-ion battery, thanks to its high energy density. The optimal integration of battery packs in the vehicle is a challenging task when designing e-mobility concepts. Therefore, this work proposes a conceptual design procedure aimed at optimizing the sizing of hybrid and battery electric vehicles. Particularly, the influence of the cell type, physical disposition and arrangement of the electrical devices is accounted for within a conversion design framework. The optimization is focused on the trade-off between the battery pack capacity and weight. After introducing the main features of electric traction systems and their challenges compared to conventional ones, the rele... [more]

This paper presents an analysis of methods to increase the efficiency of heat transfer in heat exchangers. The scope of the research included analysis of efficiency optimization using the example of two tubular heat exchanger structures most often used in industry. The obtained efficiency of heat recovery from the ground of the examined exchangers was over 90%, enabling the reduction of emissions of the heating systems of buildings. The paper presents the results of tests of two types of heat pipes using R134A, R404A, and R407C working agents. The paper also presents the results of experimental tests using the R410A working medium. The results included in the study will also enable the effective use of land as a heat store.

With the increasing depth of coal mining, the quantitative evaluation of the degree of geological structure development is becoming increasingly important for the control of mine water hazards in coal mining areas. Understanding the complexity of geological structure development can improve the safety and efficiency of coal production. At present, various evaluation indicators of the geological structure development cannot fully reflect the complexity of faults and folds, and the evaluation process is usually affected by subjective human factors. In this paper, the fractal dimension from fractal theory is used as the evaluation indicator to quantitatively analyze and evaluate the complexity of fault and fold structure in the mining area. To verify the evaluation results, the mathematical geology method is applied in an analysis of the trend surface of fault and fold networks. The results indicate that the fractal dimension can be applied for the quantitative analysis and evaluation of... [more]

New guidelines set by international organizations for refrigeration companies cause that natural working fluids such as carbon dioxide are increasingly used in new refrigeration systems. Carbon dioxide (R-744) is used in freezing, cooling, or air conditioning installations, in which the cooling load fluctuates hourly. To adapt the cooling capacity of the evaporator to the current cooling load of the cooled space, a number of control elements are used. The paper proposes a new method of regulating the cooling capacity for a one-stage refrigeration cycle with the R-744 refrigerant and an internal heat exchanger (IHX). The proposed method involves using an additional evaporator and combines the possibility of regulating the cooling capacity with the possibility of energy efficiency ratio (EER) improvement. The energy analysis of the proposed method of regulating the cooling capacity was performed and the results were compared with the control method. The control method was using the compr... [more]