The methodologies for calculating exhaust emissions and fuel consumption, which are given in the normative documents, do not take into account the fact that vehicles equipped with liquefied petroleum gas (LPG) or compressed natural gas (CNG) systems are fueled with petrol after a cold start. When calculating exhaust emissions and fuel consumption of LPG or CNG-powered vehicles, it is assumed that they result from the combustion of gaseous fuel only. This simplification leads to an incorrect determination of the emissions and fuel consumption values, as the formulas for calculating these values differ depending on the fuel type. This article presents the results of tests aimed at checking how that factor affects the value of emissions and fuel consumption calculated in the driving cycles used in the type-approval tests. In order to estimate the error resulting from this simplification, the tests of exhaust emissions and fuel consumption of a vehicle equipped with an LPG system were carr... [more]

In this paper, a switched-capacitor multilevel inverter with voltage boosting and common-mode-voltage reduction capabilities is put forth. The proposed inverter is synthesized with one-half bridge and several switched-capacitor cells. Due to the voltage boosting and common-mode current reduction features, the proposed multilevel inverter is suitable for grid-connected PV applications. In addition, an analytical lifetime evaluation based on mission profile of the proposed inverter has been presented to derive lifetime distribution of semiconductors. Whereas in the proposed inverter, any components failure can bring the whole system to a shutdown. The series reliability model is used to estimate the lifetime of the overall system. The performance of the suggested multilevel inverter in grid-connected applications is verified through the simulation results using the grid-tied model in Matlab/Simulink. Moreover, the viability and feasibility of the presented inverter are proven by using a... [more]

The power industry is rapidly changing as demand for eco-friendly and stable power supply increases along with global greenhouse gas emission regulations. Small-capacity renewable power sources represented by photovoltaics and wind are continuously increasing as a form of microgrid to supply electric power to a community or island. As a result, microgrids based on renewable resources have come into wide usage around small areas or islands in Korea. In particular, the microgrid development policy of Korea is focused on electric power quality, as well as expansion in renewable energy supply for reducing greenhouse gas emissions. From 2009, the government began to develop independent carbon-free microgrids with photovoltaic and wind powers instead of traditional power diesel generators for small islands. The goal of this paper is to investigate a feasible economic microgrid topology for implementing the carbon-free island (CFI) under an acceptable level of reliability. First, we derive th... [more]

To achieve a successful integration of fluctuating renewable power generation, the power-to-heat (P2H) conversion is seen as an efficient solution that remedies the issue of curtailments as well as reduces carbon emissions prevailing in the district heating (DH) sector. Concurrently, the need for storage is also increasing to maintain a continuous power supply. Hence, this paper presents a MILP-based model to optimize the size of thermal storage required to satisfy the annual DH demand of a community solely by P2H conversion employing renewable energy. The DH is supplied by the optimal operation of a novel 2-km deep well heat pump system (DWHP) equipped with thermal storage. To avoid computational intractability, representative time steps with varying time duration are chosen by employing hierarchical agglomerative clustering that aggregates adjacent hours chronologically. The value of demand response and the effect of interannual weather variability are also analyzed. Numerical result... [more]

In light of the advancing energy transition and an increasing amount of intermittent renewable energy to be integrated, flexibility from distributed energy resources will be key. In this paper, the Italian UVAM (Unità Virtuali Abilitate Miste, i.e., virtually aggregated mixed units) project, one of the biggest pilots in Europe to serve this purpose, is critically reviewed and mapped after two years of operation. The pilot is analyzed on a global level as well as the individual participant level. Based on the extensive analysis of actual market data, different strategies of participating companies to obtain capacity in accordance with the pilot project’s design are identified. Furthermore, the specific bidding strategies of individual participating units on the balancing market are outlined. Alongside this, the overall pilot project’s market integration, in terms of offered and accepted bids, is depicted. The thorough data analysis, therefore, serves as an input and fundamental building... [more]

Due to the oxygen shortage at high altitudes, the use of diesel engines in small aircraft is limited to a low ceiling level. Here, we propose to significantly extend the ceiling level by introducing an in-cylinder steam reforming system. In this arrangement, the fuel direct-injection assembly comprises of a two-stage process. In the first stage, a blend of methanol and water is injected into the hot previously compressed cylinder charge onto an in-cylinder catalyst. Residual heat is absorbed due to the blend evaporation and the steam-reforming process to produce hydrogen. In the second stage, diesel fuel with a lower ignition temperature than the hydrogen fuel is injected to initiate combustion, while the absorbed heat (from the first stage) is released through the hydrogen oxidation. Essentially, the absorbed heat is exploited to produce extra hydrogen fuel, which increases the cycle efficiency. In this arrangement, the in-cylinder oxygen content is significantly increased due to the... [more]

Small-scale plants that produce biodiesel have many social, economic and environmental advantages. Indeed, small plants significantly contribute to renewable energy production and rural development. Communities can use/reuse local raw materials and manage independently processes to obtain biofuels by essential, simple, flexible and cheap tools for self-supply. The review and understanding of recent plants of small biodiesel production is essential to identify limitations and critical units for improvement of the current process. Biodiesel production consists of four main stages, that are pre-treatment of oils, reaction, separation of products and biodiesel purification. Among lots of possibilities, waste cooking oils were chosen as cheap and green sources to produce biodiesel by base-catalyzed transesterification in a batch reactor. In this paper an overview on small-scale production plants is presented with the aim to put in evidence process, materials, control systems, energy consump... [more]

Satisfying the mobile traffic demand in next generation cellular networks increases the cost of energy supply. Renewable energy sources are a promising solution to power base stations in a self-sufficient and cost-effective manner. This paper presents an optimal method for designing a photovoltaic (PV)-battery system to supply base stations in cellular networks. A systematic approach is proposed for determining the power rating of the photovoltaic generator and battery capacity from a technical and economical point of view in order to minimize investment cost as well as operational expenditure, while the power autonomy of the PV-battery system is maximized in a multi-objective optimization framework. The proposed method is applied to optimally size a photovoltaic-battery system for three cases with different availability of solar power to investigate the effect of environmental conditions. Problem-solving using the proposed approach leads to a set of solutions at different costs versus... [more]

A ground source heat pump system is a high-performance technology used for maintaining a stable underground temperature all year-round. However, the high costs for installation, such as for boring and drilling, is a drawback that prevents the system to be rapidly introduced into the market. This study proposes a modular ground heat exchanger (GHX) that can compensate for the disadvantages (such as high-boring/drilling costs) of the conventional vertical GHX. Through a real-scale experiment, a modular GHX was manufactured and buried at a depth of 4 m below ground level; the heat exchange rate and the change in underground temperatures during the GHX operation were tracked and calculated. The average heat exchanges rate was 78.98 W/m and 88.83 W/m during heating and cooling periods, respectively; the underground temperature decreased by 1.2 °C during heat extraction and increased by 4.4 °C during heat emission, with the heat pump (HP) working. The study showed that the modular GHX is a c... [more]

This paper proposes a photovoltaic (PV) string-level isolated DC−DC power optimizer with wide voltage range. A hybrid control scheme in which pulse frequency modulation (PFM) control and pulse width modulation (PWM) control are combined with a variable switching frequency is employed to regulate the wide PV voltage range. By adjusting the switching frequency in the above region during the PWM control process, the circulating current period can be eliminated and the turn-on period of the bidirectional switch of the dual-bridge LLC (DBLLC) resonant converter is reduced compared to that with a conventional PWM control scheme with a fixed switching frequency, resulting in better switching and conduction loss. Soft start-up control under a no-load condition is proposed to charge the DC-link electrolytic capacitor from 0 V. A laboratory prototype of a 6.25 kW DBLLC resonant converter with a transformer, including integrated resonant inductance, is built and tested in order to verify the perf... [more]

This study presents experimental studies of charcoal gasification with CO2 at different heating rates (1, 5, 10, 20, and 50 K min−1). The kinetics of the reaction C + CO2 under pore-diffusion control is studied. We propose a new method for the proper determination of activation energy during the processing of thermogravimetric curves of porous carbon gasification under conditions of pore-diffusion resistance. The results of the inverse kinetic problem solution are compared with different hypotheses about the regime of the investigated heterogeneous reaction process (kinetic, diffusion, pore-diffusion). The change of reaction regimes from kinetic to diffusion is detected during charcoal gasification at different heating rates. At heating rates of 5−20 K min−1, the values of activation energy of carbon gasification reaction in the carbon dioxide atmosphere, obtained by the proposed method, closely match the data found in the previous studies. The use of diffusion models in the processing... [more]

The Paris Agreement has set out ambitious climate goals aiming to keep global warming well-below 2 °C by 2100. This requires a large-scale transformation of the global energy system based on the uptake of several technological options to reduce drastically emissions, including expansion of renewable energy, energy efficiency improvements, and fuel switch towards low-carbon energy carriers. The current study explores the role of Carbon Capture and Storage (CCS) as a mitigation option, which provides a dispatchable source for carbon-free production of electricity and can also be used to decarbonise industrial processes. In the last decade, limited technology progress and slow deployment of CCS technologies worldwide have increased the concerns about the feasibility and potential for massive scale-up of CCS required for deep decarbonisation. The current study uses the state-of-the-art PROMETHEUS global energy demand and supply system model to examine the role and impacts of CCS deployment... [more]

Amongst the issues associated with the commercialization of biomass gasification, the presence of tars has been one of the most difficult aspects to address. Tars are an impurity generated from the gasifier and upon their condensation cause problems in downstream equipment including plugging, blockages, corrosion, and major catalyst deactivation. These problems lead to losses of efficiency as well as potential maintenance issues resulting from damaged processing units. Therefore, the removal of tars is necessary in order for the effective operation of a biomass gasification facility for the production of high-value fuel gas. The catalytic activity of montmorillonite and montmorillonite-supported nickel as tar removal catalysts will be investigated in this study. Ni-montmorillonite catalyst was prepared, characterized, and tested in a laboratory-scale reactor for its efficiency in reforming tars using naphthalene as a tar model compound. Efficacy of montmorillonite-supported nickel cata... [more]

The physical mechanisms underlying the dynamics of the flame kernel in stationary isotropic and anisotropic turbulent field are studied using large eddy simulations (LES) combined with a pdf approach method for the combustion model closure. Special attention is given to the ignition scenario, ignition delay, size and shape of the flame kernel among different turbulent regimes. Different stages of ignition are analysed for various levels of the initial velocity fluctuations and turbulence length scales. Impact of these parameters is found small for the ignition delay time but turns out to be significant during the flame kernel propagation phase and persists up to the stabilisation stage. In general, it is found that in the isotropic conditions, the flame growth and the rise of the maximum temperature in the domain are more dependent on the initial fluctuations level and the length scales. In the anisotropic regimes, these parameters have a substantial influence on the flame only during... [more]

Geographic information system (GIS) based tools have become popular for solar photovoltaic (PV) potential estimations, especially in urban areas. There are readily available tools for the mapping and estimation of solar irradiation that give results with the click of a button. Although these tools capture the complexities of the urban environment, they often miss the more important atmospheric parameters that determine the irradiation and potential estimations. Therefore, validation of these models is necessary for accurate potential energy yield and capacity estimations. This paper demonstrates the calibration and validation of the solar radiation model developed by Fu and Rich, employed within ArcGIS, with a focus on the input atmospheric parameters, diffusivity and transmissivity for the Netherlands. In addition, factors affecting the model’s performance with respect to the resolution of the input data were studied. Data were calibrated using ground measurements from Royal Netherlan... [more]

In this paper, we investigate the economic benefits of an energy community investing in small-scale photovoltaics (PVs) when local energy trading is operated amongst the community members. The motivation stems from the open research question on whether a community-operated local energy market can enhance the investment feasibility of behind-the-meter small-scale PVs installed by energy community members. Firstly, a review of the models, mechanisms and concepts required for framing the relevant concepts is conducted, while a clarification of nuances at important terms is attempted. Next, a tool for the investigation of the economic benefits of operating a local energy market in the context of an energy community is developed. We design the local energy market using state-of-the-art formulations, modified according to the requirements of the case study. The model is applied to an energy community that is currently under formation in a Greek municipality. From the various simulations that... [more]

Wind power has been increasingly deployed in the last decade to decarbonize the electricity sector. Wind power output changes intermittently depending on weather conditions. In electrical power systems with high shares of variable renewable energy sources, such as wind power, system operators aim to respond flexibly to fluctuations in output. Here, we investigated very short-term fluctuations, short-term fluctuations (STFs), and long-term fluctuations (LTFs) in wind power output by analyzing historical output data for two northern and one southern balancing areas in Japan. We found a relationship between STFs and the average LTFs. The percentiles of the STFs in each month are approximated by linear functions of the monthly average LTFs. Furthermore, the absolute value of the slope of this function decreases with wind power capacity in the balancing area. The LTFs reflect the trend in wind power output. The results indicate that the flexibility required for power systems can be estimate... [more]

A quenching experiment is performed to investigate the heat transfer characteristics and cooling performance of CrAl-coated Zircaloy (Zr) cladding in a water flow. The CrAl-coated Zr cladding is one of the accident tolerant fuels for light water reactors. The uncoated Zr cladding is also used in this quenching experiment for comparison. This experiment simulates reflood quenching of fuel rod during loss of coolant accident (LOCA) in nuclear power plant. The test conditions were determined to represent the peak cladding temperature, the coolant subcooling and the reflood velocity in the event of LOCA. The flow visualization showed the film boiling during early stage of reflood quenching and the transition to nucleate boiling. The film layer decreases as the coolant subcooling increases and becomes wavy as the reflood velocity increases. The CrAl-coated Zr cladding showed more wavy and thinner film than the uncoated Zr cladding. The rewetting temperature increases as the initial wall tem... [more]

The following article focuses on sustainable aviation fuels, which include first and second generation biofuels and other non-biomass fuels that meet most of environmental, operational and physicochemical requirements. Several of the requirements for sustainable aviation fuels are discussed in this article. The main focus was on researching the alcohol-to-jet (ATJ) alternative fuel. The tests covered the emission of harmful gaseous compounds with the Semtech DS analyzer, as well as the number and mass concentration of particles of three fuels: reference fuel Jet A-1, a mixture of Jet A-1 and 30% of ATJ fuel, and mixture of Jet A-1 and 50% of ATJ fuel. The number concentration of particles allowed us to calculate, inter alia, the corresponding particle number index and particle mass index. The analysis of the results made it possible to determine the effect of the content of alternative fuel in a mixture with conventional fuel on the emission of harmful exhaust compounds and the concent... [more]

In view of the difficulties in coordination between reliability and sensitivity of conventional generator differential protection, this paper presents a novel generator differential protection scheme based on a new braking method. On the basis of the mathematical model of the field-circuit coupling method and the electrical network cascade characteristics, the stator windings were combined and decoupled by the improved six-sequence component method to eliminate electromagnetic coupling between winding coils. In accordance with the basic characteristics of longitudinal impedance, the function of sub-item discrimination was realized. Numerous simulations and the up-to-date dynamic experiments showed that the proposed method has good state discrimination ability and can effectively resist the influence of current transformer saturation. Thus, it has an excellent prospect for engineering promotion.

Amidst the changes and adjustments of the international energy situation, the leading trend is to shift from fossil fuels to low-carbon fuels, and ultimately, to enter the era of sustainable energy, based mainly on renewable energy. The ongoing changes in global security of energy supply and the high volatility of fossil energy prices also stimulate investment in alternative energy sources, making renewable energy sources (RES) one of the rapidly growing elements in the global energy system. This article fills the research gap by analyzing the potential of using renewable energy in the countries of the Commonwealth of Independent States (CIS) in the years 2015−2018. The authors address the energy potential in the years 2015−2019, and energy consumption in the years 2015−2018 as the potential of RES in the CIS countries was not researched after 2014. Please note that the study covers the CIS countries, along with Georgia and Ukraine, which are no longer formal members of the Community,... [more]

As electric vehicles are gaining increasing worldwide interest, advances in driving range and safety become critical. Modern automotive battery management systems (BMS) compete with challenging performance and safety requirements and need to monitor a large amount of battery parameters. In this paper, we propose power line communications (PLC) for high voltage (HV) traction batteries to reduce the BMS wiring effort. By modeling a small-scale battery pack for frequencies up to 300 MHz, we predict the PLC channel transfer characteristics and validate the results using a PLC hardware demonstrator employing a narrowband single-carrier modulation. The results demonstrate that battery PLC is a demanding task due to low access impedances and cell coupling effects, yet transfer characteristics can be improved by optimal impedance matching. PLC for HV BMS not only saves weight and cost, but also improves flexibility in BMS design. PLC enables single-cell monitoring techniques such as online ele... [more]

The high incidence of electricity theft, meter tampering, meter bypassing, reading errors, and defective and aged meters, among others, increases utility losses, especially non-technical losses (NTL). A utility in Ghana piloted a non-technical loss reduction program in 2019 to replace postpaid meters with anti-tamper, anti-fraud, and anti-theft smart prepaid meters. By using customer-level residential billing panel data from 2018 to 2019 obtained from the utility, we assess the effectiveness of this program using the difference-in-differences fixed-effect approach. On average, the results indicated that the reported amount of customers’ monthly electricity consumption increases by 13.2% when any tampered postpaid meter is replaced with a smart prepaid meter, indicating the NTLs by customers. We further employed quantile difference-in-differences regression and observed that reported energy consumption has increased for all households except those at the lower quantile (25th quantile).... [more]

The transition to electric vehicles (EVs) has received global support as initiatives and legislation are introduced in support of a zero-emissions future envisaged for transportation. Integrated on-board battery chargers (OBCs), which exploit the EV drivetrain elements into the charging process, are considered an elegant solution to achieve this widespread adoption of EVs. Surface-mounted permanent-magnet (SPM) machines have emerged as plausible candidates for EV traction due to their nonsalient characteristics and ease of manufacturing. From an electric machine design perspective, parasitic torque ripple and core losses need to be minimized in integrated OBCs during both propulsion and charging modes. The optimal design of EV propulsion motors has been extensively presented in the literature; however, the performance of the optimal traction machine under the charging mode of operation for integrated OBCs has not received much attention in the literature thus far. This paper investigat... [more]

The jet impingement phenomenon plays an important role among the heat transfer intensification methods. Very often its application and analyses refer to simple flat surfaces, while there is a lack of information in the literature for cases addressing curved surfaces. In the present work, the single jet impingement on the non-flat (concave and convex) surface is studied for a wide range of geometries, which originate from the mini-jet heat-exchanger design. The numerical simulations were performed by an advanced ζ-f turbulence model implemented in the open-source OpenFOAM (ESI-OpenCFD Ltd, Bracknell, United Kingdom) code. Noticeable differences in the phenomena occurring on the convex and concave surfaces were identified in the stagnation zone. Besides, the existence and location of the secondary peak in the Nusselt number distribution differed between the cases. These distributions were influenced by the shape of geometry, which determined flow characteristics and resulting heat transf... [more]