Silica nanoparticles (SNPs) consist of several applications which include lightweight aggregates, energy storage, and drug delivery. Nevertheless, the silica reagents used in SNP synthesis are both costly and hazardous. As a result, it is critical to look for other sources of silica. For this research, a simple sol−gel hydrothermal approach is used to make SNPs from South African fly ash (SAFA). SAFA is classified as fly ash class F according to X-ray fluorescence (XRF) analysis. The wide-angle X-ray diffraction (XRD) pattern reveals the structural composition of SAFA and the amorphous phase of extracted SNPs, while Fourier transform infrared (FTIR) examination reveals the presence of silanol and siloxane groups. Basic SNPs were generally spherical with diameters of about 60 nm, according to scanning electron microscopy (SEM) and transition electron microscope (TEM) studies. The presence of SiO2 is confirmed by energy-dispersive X-ray spectroscopy (EDX) spectrum analysis. Particle size... [more]

Cement hydration within particle bed concrete 3D printing processes can be benefited by storing water in the otherwise dry aggregate bulk material. Additional water also has the advantage of acting as a source of passive cooling. However, even small amounts of liquid lead to detrimental effects on bulk properties, such as the flowability. For that reason, this study proposes implementing dry water (DW) in order to store large amounts of water in a bulk material of non-absorbent, coarse sand whilst maintaining its initial bulk properties. DW is essentially created by mixing water and hydrophobic fumed silica in a high shear process, leading to water droplets surrounded by a protective silica shell. Herein, several DW variants, distinguished by their deionised water to hydrophobic silica ratio, were mixed with non-absorbent, coarse sand particles. In addition, mixtures were produced to contain a specific overall water content of up to wH2O = 5% within the bulk material. It was shown that... [more]

This work shows some advanced studies in model pharmaceutical formulations that help to develop guidelines for the rational design of controlled release systems [...]

A kinetic study was conducted experimentally for the precipitation of ferrous oxalate. The ferrous oxalate, in the form of dihydrate (FeC2O4·2H2O), was produced by the acidic dissolution of ferrous ammonium sulfate (Fe(NH4)2(SO4)2) in an aqueous solution of oxalic acid, and then precipitated by nucleation and particle growth from supersaturated solution. The effect of the concentration of ferrous ammonium sulfate and oxalic acid as raw materials was investigated on the kinetics of the ferrous oxalate precipitation. Temperature was kept constant at 25 °C. The surface morphology, atomic compositions, and crystal phase were characterized for the ferrous oxalate precipitate collected. As the initial concentration of ferrous ammonium sulfate increased, the initial precipitation of ferrous oxalate occurred faster. The concentration of oxalic acid did not significantly affect the rate of precipitation of ferrous oxalate. The experimental behavior of ferrous oxalate precipitation was modeled w... [more]

L. is widely distributed in Saudi Arabia. However, only a few studies have been reported regarding this species. In this study, we investigated the phytochemical analysis of R. officinalis essential oil using GC-MS analysis in order to identify its major components; the in vitro antimicrobial activity of the essential oil was also evaluated using disc diffusion assay against gram-positive (S. aureus) and gram-negative bacteria (E. coli), the antimicrobial activity was also assessed with molecular docking against several microbial proteins; TyRS, DNA gyrase and DHFR. The GC-MS analysis has indicated the presence of 18 constituents, representing 99.93 % of the total oil content. The major compounds detected were Bornyl acetate (26.59%), Eucalyptol (17.38%), Camphor (10.42%), Borneol (9.78%), Beta-Caryophyllene (7.80%) and α-pinene (3.85%). The antimicrobial study showed that R. officinalis has strong antimicrobial activity against S. aureus with an inhibition zone of 30 mm and E. coli wi... [more]

Three-dimensional printing is one of the most promising areas of additive manufacturing with a constantly growing range of applications. One of the current tasks is the development of new functional materials that would allow the manufacture of objects with defined magnetic, electrical, and other properties. In this work, composite magnetic filaments for 3D printing with tunable magnetic properties were produced from polylactic acid thermoplastic polymer with the addition of magnetic ferrite particles of different size and chemical composition. The used magnetic particles were cobalt ferrite CoFe2O4 nanoparticles, a mixture of CoFe2O4 and zinc-substituted cobalt ferrite Zn0.3Co0.7Fe2O4 nanoparticles (~20 nm), and barium hexaferrite BaFe12O19 microparticles (<40 µm). The maximum coercivity field HC = 1.6 ± 0.1 kOe was found for the filament sample with the inclusion of 5 wt.% barium hexaferrite microparticles, and the minimum HC was for a filament with a mixture of cobalt and zinc−co... [more]

Improving the dielectric properties of liquid-insulating materials is a current problem in research into the insulation system of a power transformer. Modern optimization of insulating liquids involves the potential use of unique synthetic esters enriched with nanoparticles. This study presents the results of the dielectric response of liquefied gas-based (GTL) insulating liquids during accelerated thermal aging. The dielectric relaxation spectroscopy method was used in the frequency domain to point out power losses as an imaginary part of a complex electric modulus. The relaxation spectra express the validity of applying this complex dielectric parameter. The polarization processes of the base oil alternately change position in the low-frequency band during thermal aging. Fullerene nanofluid undergoes three phases of dielectric loss changes during thermal aging. In the case of magnetic nanofluid, the effect of electric double-layer polarization disappeared after 500 h of thermal aging... [more]

A series of material tests were performed on cryogenic metallic materials meant for liquid hydrogen storage tanks using a 20 K tensile cryostat and an electrochemical hydrogen-charging apparatus. Mechanical evaluation of the electrochemically hydrogen-charged specimens was performed in a tensile cryostat using helium gas at ambient temperature and cryogenic temperature (20 K). The tensile cryostat was equipped with a vacuum jacket and a G-M cryocooler with gaseous helium. Furthermore, the cathodic electrolysis cell used for charging the specimens was adopted for internal hydrogen conditions with a reflux condenser and heating mantle to increase hydrogen diffusivity. The target materials were austenite stainless steel and aluminum alloy, which are suitable for liquefied natural gas and gaseous hydrogen environments. No significant change in the yield strength and flow stress of the hydrogen-charged specimen up to 20% strain was observed. However, changes in tensile strength and elongati... [more]

Fused-filament fabrication is one of the most popular 3D printing techniques for thermoplastic materials because it is easy to use and is low-cost. On the other hand, it has the great limit of being suitable only for developing prototypes, because the printed object generally has low mechanical properties, and this prevents its use in structural applications. To solve this issue, the scientific literature has mainly focused on the optimization of the printing parameters and on performing some post-printing treatments, e.g., annealing, but despite some results being very promising, the topic has not yet been exhaustively investigated. In this paper, a post-printing treatment was studied that was based on two subsequent stages of remelting and compaction within a mold made of a granular material. The material chosen for this study was a green composite made of poly-(lactic acid) and poly-(hydroxyalkanoate) filled with wood fibers. The density, mechanical properties in terms of tension an... [more]

Yeast produces flavor components as by-products of fermentation. Such components, which account for considerable yeast quality value, may influence cell membrane fluidity and regulate cell size. In this study, yeast cell size was measured using various methods, and cell sizes were characterized for each strain of yeast. Herein, a method for measuring the cell size and automatically acquiring the cell area was proposed using inexpensive methylene blue staining and a versatile digital microscope to automatically acquire the cell area. To evaluate the efficiency, data on cell length and area were compared using the conventional and proposed methods. Additionally, the advantages of automated measurement and the ability to count cell numbers in the future are discussed through the acquisition of cell size data, which would be required for microfabrication and cell fabrication techniques. Although there are various candidate methods for evaluating the properties of each yeast strain, the pre... [more]

The serious environmental issues associated with CO2 emissions have triggered the search for energy efficient processes and CO2 capture technologies to control the amount of gas released into the atmosphere. One of the suitable techniques is CO2 adsorption using functionalized sorbents. In this study, a functionalized activated carbon (AC) material was developed via the wet impregnation technique. The AC was synthesized from a rubber seed shell (RSS) precursor using chemical activation and was later impregnated with different ratios of [bmpy][Tf2N] ionic liquid (IL). The AC was successfully functionalized with IL as confirmed by FTIR and Raman spectroscopy analyses. Incorporation of IL resulted in a reduction in the surface area and total pore volume of the parent adsorbent. Bare AC showed the largest SBET value of 683 m2/g, while AC functionalized with the maximum amount of IL showed 14 m2/g. A comparative analysis of CO2 adsorption data revealed that CO2 adsorption performance of AC... [more]

The special features of metal−organic frameworks (MOFs), namely, tunable porosity, exceptional structure, high surface area and high adsorption capability enable them to be widely studied in many applications including carbon capture and storage (CCS), biomedical engineering, catalysis and pollutant treatment. Despite these remarkable properties, MOFs are known to be moisture-sensitive, hardly recyclable and expensive in fabrication cost which limits their breakthrough performance in more efficient uses. Recently, extensive studies have been devoted to counter those shortcomings by embedding MOFs with support materials using various series of synthetic designs to yield incorporated MOF hybrid materials to counter their limitations. In view of this interest, this review summarizes the latest developments of incorporated MOFs with various materials, namely, ionic liquids (ILs), membranes and metal species. Pre-synthetic and post-synthetic synthesis methods are also discussed. This review... [more]

Fuel cells are considered as efficient and environmentally ecofriendly alternatives for energy production. The oxygen-reduction reaction is important in energy-conversion systems for fuel cells. In this work, rhodium (Rh) and cobalt (Co) alloy nanoparticles were deposited on nitrogen (N)-doped carbon (C) supports (RhCo/NC) using ball milling and thermal decomposition. The RhCo/NC composites were transformed into small nanoparticles with an average diameter of approximately 4 nm. The properties of the as-synthesized RhCo/NC nanocatalyst were characterized through transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Raman spectroscopy. The catalytic activity of the nanocatalyst for the ORR was investigated. The RhCo/NC nanocatalyst showed good activity for the ORR, long-term durability in chronoamperometry tests, and resistance to methanol crossover in an alkaline solution. This was because of the synergistic effects of the metal alloy. Chronoamperom... [more]

Tungsten-heavy alloys (WHA) are a pseudo-alloy in which tungsten is the primary phase and remains filled with additives such as Ni−Fe and Ni−Cu. These alloys are widely used to make their applications’ structural, electrical, and electronic components. According to this study, in addition to processing factors, the prime factors affecting the performance of WHAs are microstructural features such as tungsten and matrix composition, powders shapes and sizes, and distributions of tungsten particles in the matrix, as well as interface-bonding strength between the tungsten particle and matrix. This study summarises current developments in WHA processing, microstructure, and mechanical characteristics. For the manufacture of WHAs, various processing methods are discussed, including traditional powder metallurgy (PM), microwave sintering (MW), spark plasma sintering (SPS), and additive manufacturing (AM). SPS process depicts better results when compared with conventional sintering. This revie... [more]

Previously, we showed that the crude methanol extracts of Leucas indica flowers exhibited antioxidant properties and in the current study, crude methanol flower extracts of L. indica showed anticancerous properties as evidenced cytotoxicity (MTT assay test) against the selected cancerous cell lines HeLa, HCT116, HL-60, and MCF-7. Therefore, further analysis was performed to isolate and purify the bioactive compound using activity-guided repeated fractionation of the methanol extract by silica gel column chromatography. After collection of different fractions, all the fractions were subjected to TLC analysis and the fractions which yielded the same compounds on TLC were further analyzed for physicochemical and spectroscopic analyses, e.g., UV, IR, 1H NMR, 13C NMR, COSY, HSQC, and mass spectroscopy. The bioactive compound isolated was elucidated as 6-hydroxy-3-(4-hydroxyphenyl)-7-(3,4,5-trihydroxy-6-)(hydroxymethyl)tetrahydro-2H-pyran-2yl)-4H-chromen-4-one. Based on the antioxidant and a... [more]

Cracks in concrete structures reduce bearing capacity, durability, and safety. This paper reveals the effect of superabsorbent polymers (SAP) on the self-healing property of pre-damaged concrete based on mechanical properties tests, mercury intrusion porosimetry, scanning electron microscopy, and energy dispersive spectrometer. The experimental results show that SAP reduces the mechanical properties of the SAP-modified concrete under the same W/C ratio, but a small amount of SAP can improve the later strength under the 0.35 W/C ratio. The addition of SAP increased the volume of small capillary pores (100 μm) and significantly reduced the former with an increase in age. The SEM-EDS analysis indicates that the water released by SAP promotes the formation of C-S-H gel. AFt in the cracks is the main reason for self-healing, and the addition of CO2 to produce calcium carbonate is another one. Furthermore, this study finds that SAP-modified concrete has the best self-healing effect and the d... [more]

The long dissolution time and large dispensed volumes of oil repellent polymers in offshore oil fields lead to a great increase in the volume and number of dissolution and maturation tanks in the polymer formulation system. However, there is limited space and load-bearing capacity at the offshore platform and only a small space is available for the dispensing system. To further optimize the polymer dispensing system and reduce its floor space, the super-gravity technology may be considered as a way to speed up the dissolution of the polymer. The mechanism of super-gravity rapid dissolution was investigated by establishing mathematical models and with indoor experiments. The effects of filler pore size and super-gravity factor on polymer dissolution time and solution viscosity were investigated using the super-gravity rapid dissolution device, then combined with established graded forced stretching devices for field magnification experiments. The results indicated that the super-gravity... [more]

Nitrogen, phosphorus, and metals’ pollutants discharged from industrial sources eventually accumulate in lake sediment, hence increasing the difficulty of sediment treatment and disposal. In this work, the water storage ceramsite is prepared from dredged lake sediment and cyano-bacterial powder. The effects of pyrolysis temperature and cyanobacterial sediment on the porosity of ceramsite were investigated. The results showed that the pyrolysis of organic matter and the de-composition of compounds or salts can produce gas, causing a rich pore structure inside the ceramsite. When the temperature increased to 1150 °C, vitrification would collapse the pore structure inside the material. At the cyanobacterial-to-sediment ratio of 3:7, the porosity and water absorption of the material could reach 81.82% and 92.45% when the pyrolysis temperature was 500 and 1050 °C, respectively. The internal macropore structure of ceramsite improved the water absorption performance, and the mesoporous struct... [more]

The effect of phospholipid nanoparticles with different contents of phosphatidylcholine (PhNP80 and PhNP100) on dsDNA was studied by means of the electrochemical method. Changes in the electrochemical behavior of heterocyclic bases guanine, adenine and thymine in the range of potentials of 0.2−1.2 V in the presence of PhNPs were used for the assessment of the binding mechanism of the ligand−DNA interaction. Comparative analysis of the effect of PhNPs with different contents of phosphatidylcholine showed a more pronounced effect on the dsDNA of the PhNP100 nanosystem. From the obtained experimental data on the decrease in the amplitude of the nucleobases’ electrochemical oxidation currents, the electrochemical coefficient of the toxic effect was calculated as the ratio of the electrooxidation currents of dsDNA and dsDNA in the presence of phospholipid nanoparticles. PhNP80/100 (up to 11.4 mg/mL) does not influence dsDNA, PhNP80/100 (14.3−28.5 mg/mL) has a moderate toxic effect on dsDNA,... [more]

Barium sulfide is an important intermediate in the manufacture of ceramics, glass, plastics, and pharmaceutical products. This substance is traditionally obtained by carbothermal reduction of barite (barium sulfate) in the presence of a carbon-containing reducing agent, mainly coal. Herein, it is demonstrated that compaction of the charge before the carbothermal reduction significantly enhances the conversion of barium sulfate to sulfide due to an increase in the contact time of carbon monoxide with barite in a compact sample in comparison with a powder sample. In the presence of NaOH as a catalyst, the degree of conversion of barium sulfate in a compact sample was 0.95−0.97 upon roasting at 1150 °C for 65 min, while in a powder sample this value did not exceed 0.6. Furthermore, charge compaction reduced the conversion activation energy (136 vs. 264 kJ mol−1), which could be a tool for reducing the energy intensity of obtaining barium sulfide from its sulfate.

Accurate production efficiency evaluation can assist enterprises in adjusting production strategies, improving production efficiency, and, thereby, weakening environmental impacts. However, the current studies on production efficiency evaluation do not accurately consider interactions inside the production system in parallel production processes. Based on the concept of the manufacturing service, this paper describes the production process of a complex product system (CoPS) with a manufacturing service chain. An efficiency calculation model based on the triangular intuitionistic fuzzy number−solid waste recycling−super-efficiency data envelopment analysis (TIFN-SWR-SDEA) is proposed under the consideration of the internal parallel structure of the production system on the example of solid waste recycling. Additionally, the technique for order preference by similarity to ideal solution (TOPSIS) method and the entropy weight method were combined to determine the proportion of solid waste... [more]

In this study, a superabsorbent polymer dryer (Polydryer) used to obtain dried medicinal plant materials (Simplicia) was incorporated with a heater to enhance the drying rate. In general, the Polydryer was constructed using a cabinet containing polymer hydrogel (polygel), a gas-fueled heater, and a drying cabinet. A polygel synthesized from acrylic acid and cassava starch was utilized to reduce the moisture content in the drying air prior to entering the heater. The drying performance of the Polydryer with and without heater operation was investigated. The results showed that the drying in the Polydryer with heater operation required 18−26 h to attain a final moisture content of 8.8−10%, significantly faster than the Polydryer without heater employment (95−119 h). In addition, the drying of medicinal plants in the modified Polydryer followed the Page thin-drying model. The Simplicia products also showed a slightly lighter color, with no significant structural differences than those obt... [more]

In emergency rescue operations, it is very important for emergency management to arrange emergency materials scientifically and reasonably according to emergency needs. However, the decision criteria for emergency material distribution are often diverse, coupled with the lack of information acquisition due to the suddenness and development complexity of disasters, which makes the scientific decisions about emergency material distribution face great challenges. This paper proposes a multi-criteria decision optimization model of emergency material distribution under uncertainty that combines the 4E criteria of performance evaluation (economic criterion, efficiency criterion, effectiveness criterion and equity criterion). Then, the solution method of the multiple decision criteria model is designed. Finally, a case study of emergency medical material distribution during COVID-19 in China was conducted for model verification. The results show that different decision criteria have an import... [more]

Accurate evaluation of shale oil reservoir fracability helps avoid blind fracturing and ensures efficient fracturing. However, the current evaluation of the fracability index rarely considers the impact of hydration caused by drilling fluid invasion during drilling. The results of a rock triaxial mechanical test conducted to evaluate the mechanical properties of shale oil reservoirs are reported in this paper. Based on the results, we developed a comprehensive evaluation method of shale oil reservoir fracability that considers hydration; the effects of the brittleness index, horizontal difference stress, and fracture toughness; and the law of water phase intrusion into shale oil reservoirs. The research results show that the average compressive strength decreased by 37.99%, the average elastic modulus decreased by 53.36%, and the average Poisson’s ratio increased by 68.75% after being soaked for 48.00 h at 80 °C and 30.00 MPa. The water saturation rate at the borehole wall was the high... [more]

The new process developed here consisting of sulfurization roasting transformation and water immersion can effectively realize the separation of rare earth elements (REEs) and impurities from spent Nd-Fe-B magnets. For the industrial application of the new process, it is critical to determine how to economically and efficiently prepare rare earth oxide (RExOy) products with higher purity from the obtained water leaching solution. Therefore, according to rare earth sulfate (RE2(SO4)3) solution characteristics, the oxalic acid precipitation−calcination method, sodium carbonate precipitation−calcination method, and double sulfates precipitation−alkali conversion−calcination method were optimized and compared. The results show that the recovery efficiency of REE recovery via the oxalic acid precipitation−calcination method is 99.44%, and the purity of RExOy is 99.83% under optimal technological conditions. However, the cost of oxalic acid precipitation is higher. The process consisting of... [more]