The class III reservoir in the Daqing Oilfield has poor sand body development, poor reservoir physical properties, and poor effects of measures. Its water drive recovery degree is low and the remaining reserves are large. It is the key target oil layer of the Daqing Oilfield. Due to the sedimentary characteristics and reservoir physical properties of class III reservoirs, conventional EOR technology (chemical flooding) and conventional stimulation and injection measures (fracturing) have poor potential tapping effects on class III reservoirs. According to the special reservoir conditions and development characteristics of the class III reservoir in the Daqing Oilfield, fracture-flooding technology is innovatively proposed, which greatly improves the recovery of remaining oil in class III reservoirs. The rapid injection of hydraulic surface activators into the formation and displacement of the remaining oil in class III reservoirs through rock core flooding experiments were simulated in... [more]

The Lufeng Sag and Huizhou Sag, both located in the Zhu-1 Depression, have similar geographical locations, but their reservoir characteristics in the Paleogene Wenchang Formation show obvious differences. Primary intergranular pores are mainly developed in the Lufeng Sag. However, secondary pores are the main reservoir space in the Huizhou depression. Overall, the reservoir properties of the Lufeng Sag are better than those of the Huizhou Sag. To analyse the differences between the Paleogene reservoirs in these two areas, this study mainly uses assay data, such as rock thin sections, scanning electron microscope images, drilling, and logging, to analyse the differential development mechanisms of high-quality reservoirs, and two types of reservoir development models were concluded. The results show that the anti-compaction primary porosity preservation mode is mainly developed in the Lufeng Sag. High compositional maturity quartz sandstone is the congenital condition of primary porosity... [more]

Adaptive calibration for ultrasound reflectometry methods used in the detection of lubrication film thickness is of great research interest. This is mainly due to the versatile non-destructive implementation of the technology in industrial applications, allowing for measurements of the lubrication film thickness, which directly relates to the friction, wear, and overall efficiency of the system. This study reviews and compares a curve fitting, extended Kalman filter, and resonance frequency detection adaptive calibration approach. Furthermore, the study compares two different regression models, used for the curve fitting and the extended Kalman filter approach. The study compares the methods and regression models based on both a theoretical and experimental analysis. The experimental analysis is based on data with varying lubrication film thickness. The lubrication film thickness is varied such that the resonance frequency is both detectable and non-detectable within the ultrasound tra... [more]

The visual linking of a building’s occupants with the outside views is a basic property of windows. However, vision through windows is not yet a metricized factor. The previous research employs a human survey methods to assess the vision through conventional windows. The recently fabricated smart films add a changeable visual transparency feature to the windows. The varied operating transparency challenges the evaluation of vision. Therefore, surveying human preferences is no longer a feasible approach for smart windows. This paper proposes an image-processing-based approach to quantify the vision quality through smart windows. The proposed method was experimentally applied to a polymer dispersed liquid crystal (PDLC) double-glazed window. The system instantaneously determines the available contrast band of the scenes seen through the window. The system adjusts the excitation of the PDLC film to maintain a desired vision level within the determined vision band. A preferred vision ratio... [more]

A tapered pile (TP) is a new type of pile with a good bearing capacity, and scholars have conducted in-depth research on its static bearing characteristics. However, there is relatively little research on its dynamic bearing characteristics. In this paper, the horizontal vibration behavior of a tapered pile in arbitrarily layered soil is studied. Utilizing the Winkler foundation model and Timoshenko beam model to simulate pile-surrounding soil (PSS) and a tapered pile, respectively, the horizontal vibration model of a tapered pile embedded in layered soil was built. The analytical solutions for the horizontal displacement (HD), bending moment (BM), and shear force (SF) of a tapered pile were derived, and then the solutions for the horizontal dynamic impedance (HDI), rocking dynamic impedance (RDI), and horizontal-rocking coupling dynamic impedance (HRDI) of pile head were obtained. Using the present solutions, the effects of soil and pile properties on the horizontal vibration characte... [more]

This work presents an investigation of the fully strained GaAsN/GaAs heterostructures obtained by atmospheric pressure metalorganic vapor phase epitaxy, focusing on the analysis of the strain generated in the GaAsN epilayers and its correlation with the formation of split interstitial complexes (N-As)As. We analyzed strained GaAsN epilayers with nitrogen contents and thicknesses varying from 0.93 to 1.81% and 65 to 130 nm, respectively. The composition and thickness were determined by high resolution X-ray diffraction, and the strain was determined by Raman spectroscopy, while the N-bonding configurations were determined by X-ray photoelectron spectroscopy. We found that the strain generated in the GaAsN epilayers is mainly caused by a lattice mismatch with the GaAs substrate. This macroscopic strain is independent of the amount of (N-As)As interstitial defects, while the local strain, induced by an alloying effect, tends to decrease with an increasing ratio of (N-As)As interstitial de... [more]

The effect of stylolite caused by the pressure dissolution process on the reservoir petro-physical properties is still controversial. This study aims to reveal the effect of stylolite on the porosity and permeability of packstone and wackestone in the Mishrif Formation from the Ah oilfield in the Middle East. Based on the observation of thin sections and cores, X-ray diffraction analysis and porosity and permeability measurement, the lithofacies, diagenesis and patterns of stylolites have been investigated. There are six lithofacies in the Mi4 member, including bivalve green algae packstone, green algae packstone, pelletoid green algae packstone, echinoderm packstone, rudist packstone, planktonic foraminifera wackestone and bioclastic wackestone. The mechanical compaction and pressure dissolution could be observed in these lithofacies, with the development of dissolution seams and stylolites. The density of stylolite has a relationship with the lithofacies and early cementation. The bo... [more]

The need for environmentally benign portable energy storage drives research on organic batteries and catalytic systems. These systems are a promising replacement for commonly used energy storage devices that rely on limited resources such as lithium and rare earth metals. The redox-active TEMPO (2,2,6,6-tetramethylpiperidin-1-oxyl-4-yl) fragment is a popular component of organic systems, as its benefits include remarkable electrochemical performance and decent physical properties. TEMPO is also known to be an efficient catalyst for alcohol oxidation, oxygen reduction, and various complex organic reactions. It can be attached to various aliphatic and conductive polymers to form high-loading catalysis systems. The performance and efficiency of TEMPO-containing materials strongly depend on the molecular structure, and thus rational design of such compounds is vital for successful implementation. We discuss synthetic approaches for producing electroactive polymers based on conductive and n... [more]

The research described in this article was carried out on samples of sandstone obtained from the underground excavations of four hard coal mines that operate in the region of Poland with the highest energy resources, i.e., Upper Silesia. The majority of underground tunnel excavations are mainly drilled using roadheaders, the organs of which are equipped with conical picks. The selection of pick type is usually based on rock compressive strength. However, sandstones often cause more problems during cutting compared to other waste rocks because of their variety. This article’s primary purpose is to emphasize the importance of researching various properties of waste rock in addition to uniaxial compression strength, which is crucial in the selection of both the appropriate cutting method and appropriate cutting tools. Accordingly, relations between mineralogical, petrographic, physical and mechanical properties were examined in this study, with special attention paid to the abrasive prope... [more]

The water blocking damage to the reservoir caused by the invasion of external fluid is one of the main factors that affect the efficient development of tight sandstone gas reservoirs. In this paper, microfluidic chip technology is used to explore the causes of water blocking damage in porous media and find suitable recovery solutions. The research results show that reducing the gas-liquid capillary pressure can effectively reduce the rate and quantity of spontaneous speed of cores. After chemical treatment, the liquid phase fluidity of the non-fractured matrix core is increased by 1.72 times, and that of the fractured core is increased by 2.13 times. In water wetting porous media, there are mainly four types of liquid hold-up: (1) Liquid hold-up in the dead volume of a non-connected pore; (2) The water phase in the pore throat with a small inner diameter cannot be driven away due to its larger capillary pressure; (3) Adsorption viscous force, the wetting phase is adsorbed on the surfac... [more]

In this study, to use carbon nanotubes (CNTs) as a conductive material instead of carbon black in cathode electrodes, their dispersions were prepared in 1-Methyl-2-pyrrolidinone (NMP) solvent by using an ultrasonic horn, and their dispersion stability was analyzed using CNTs on the formation of the network between cathode electrode constituent materials comprised of cathode material, CNTs, and current collectors, and their correlation with electrochemical performance results were investigated using various analytical techniques. Particularly, in the analysis, terahertz time domain spectroscopy (THz-TDS), a new non-destructive analysis method, was used to analyze and compare the various optical properties of the cathode’s slurries that co-existed with CNTs and cathode material, suggesting the suitability of its analytical use in the field of materials dispersion and the slurry manufacturing process for lithium-ion batteries (LIBs). In the investigated results, the sample with the highes... [more]

This paper proposes a rational approximation-based approach to find positive real parameters for the extended Debye model (EDM), aimed at condition assessment of insulation systems of power transformers. The EDM can model the slow and fast polarization phenomenon, including relaxation mechanisms with different relaxation times within a composite dielectric material. In the proposed approach, the complex permittivity of the transformer’s composite insulation is approximated via rational functions, as given by the vector fitting (VF) software tool, and the EDM parameters are identified from the obtained poles/residues. To guarantee positive real parameters, i.e., a physically realizable circuit, VF is internally modified to calculate the final residues of the rational approximation via a constrained linear least-squares problem without resorting to further post-processing algorithms, as in existing methods, hence without affecting fitting accuracy. The effectiveness of the parametrized E... [more]

The monitoring of partial discharges (PDs) is one of the main methods used worldwide for evaluation and diagnosis of the insulation conditions in equipment powered by medium and high voltages. The occurrence of PDs is usually an indication of the appearance of insulation defects, which over time can compromise the dielectric withstand of the material used, increasing the probability of complete breakdown. In general, laboratory tests for detecting and registering PDs are carried out using purely sinusoidal voltages. However, it is very common for an electrical asset to be subjected at some point in its operating life to voltages distorted by harmonic components. Some studies reported in the literature reveal that harmonic distortions can affect the PDs’ characteristics, nevertheless, the effects of individual harmonic components on PDs still need to be analyzed. In this context, this paper proposes to evaluate the impacts of harmonic voltage distortions on the dynamic behavior and the... [more]

The interest in passive construction that has low demand for thermal energy continues to grow every year. It is related to both the reduction in maintenance costs of buildings and the growing environmental awareness in societies. Passive houses are characterised by very good thermal insulation properties of their external partitions. This paper presents the results of tests on the thermal conductivity for three different types of building materials, assuming their use as thermal insulation. The materials were subjected to water absorption tests during long-term immersion. The purpose of this study was to simulate water absorption caused by long-term water exposure. The tests were carried out on a perlite concrete block, a sheet of polyurethane foam applied by spraying and expanded clay in a loose form in three different fractions. The tested insulation materials were selected due to their different form, structure, and porosity characteristics, which largely determined the value of the... [more]

Concentrating solar power (CSP), also known as solar thermal electricity (STE), is increasing its deployment worldwide. One of the potential ways to decrease costs in CSP plants is the improvement of corrosion resistance between the heat transfer fluid (HTF) and storage materials, and the materials used for pipes, tanks, containers, and receivers. This paper assesses the literature on this topic (290 publications) through a bibliometric analysis, identifying the trends of the research, the topics of most interest to researchers, and literature gaps. Most documents are from Spain, Germany, and the United States of America. Results show that the most recent approaches for corrosion migration are selective coatings and the use of nanoparticles to reduce corrosiveness. The use of nitrates is changing to other salts such as chloride mixtures and potassium compounds. In addition, the techniques used to evaluate corrosion results are dominated by scanning electron microscopy (SEM), X-ray diff... [more]

A numerical study is conducted to evaluate the steady natural convective heat transfer problem and entropy generation of both single wall (SWCNT) and multi wall (MWCNT) nanoparticles with water as a base liquid over two spaced spheres. The isothermally heated spheres are located between two plates of short length. The cooled plates are maintained at different inclination angles. A numerical approach based on the finite volume method and multigrid acceleration was used to solve the governing equations. The effects of nanoparticle type, volume fraction, the inclination angle of the plates and the Rayleigh numbers are well-considered. Results reveal that there is a remarkable enhancement of the average Nusselt number over the plates for MWCNT nanoparticles with 63.15% from the inclination angle 0° to 30°. Furthermore, optimal heat transfer rates over the plates for MWCNT nanoparticles equates to 1.9, which is obtained for the inclination 30° and a Rayleigh number of 106. However, for SWCN... [more]

Wave velocity under different pressure and temperature (PT) conditions plays an important role in the exploration of oil and gas reservoirs. We obtained the mineral composition and porosity of 20 underground sandstone and mudstone samples in Yinggehai Basin via X-ray diffraction and porosity measurements. Using high-frequency ultrasound, the P- and S-wave velocities of four samples under high temperature and overpressure conditions were found to vary significantly, owing to the material composition and porosity. According to the comparison between the experimental conclusion and the well-logging data, the genesis of false bright spot and dark spot gas reservoirs in the study area was analyzed. The variation in P-wave velocity under different temperature and pressure conditions was explained with the PT coefficient. The traditional pressure−velocity and temperature−velocity prediction methods were improved and applied to well-logging data. Herein, the velocity of P- or S-waves of sand a... [more]

An innovative water-treatment process consisting in reducing the nitrate concentration by using an active silica filter obtained from ashes produced during rice-straw thermal treatment has been developed by the LIFE LIBERNITRATE project. A life-cycle assessment (LCA) was carried out to evaluate the environmental impacts of this innovative process, from the production of ashes and extraction and activation of silica to the water treatment. These results were compared to the environmental impact derived from the use of bottled water, instead of tap water, where traditional water treatments (i.e., reverse osmosis) may not be available due to the high installation and operating costs. The comparison showed that the proposed innovative process could contribute to reducing the environmental impact in almost all analyzed impact categories (from 20% for photochemical oxidation to 90% for abiotic depletion) with respect to the use of bottled water. In addition, if conveniently optimized (for ex... [more]

Lignocellulosic biomass is a nonedible matrix that can be efficiently exploited as feedstock in an integrated biorefinery after a proper pretreatment. An organosolv pretreatment using an acidified γ-valerolactone (GVL)/water solution was proposed to improve the cellulose enrichment and enzymatic saccharification of cardoon (Cynara cardunculus L.) stems. At the optimal pretreatment condition (140 °C, 0.6 GVL/water, and 2.24% H2SO4), xylan was efficiently removed from the cardoon, and up to 50% of its content was recovered in the aqueous fraction, while 86% of the cellulose was retained in the solid fraction. The resulting cardoon pulp showed a cellulose content of 91.5% and an enzymatic digestibility of 100%. An overall glucose production of 37.17 g/100 g raw material (90% theoretical maximum) was obtained using high solid loading (20% w/w) and a high enzyme dosage (60 FPU/g cellulose). At a low enzyme dosage, glucose concentrations of 169 g/L and 210 g/L were achieved using 10 FPU/g ce... [more]

Drilling fluid represents the most important fluid that must fulfill numerous important assignments during drilling operations. Many commercially available additives for water-based drilling fluid fall into the category of non-degradable and environmentally hazardous materials. Significant development in this area can be made by using biodegradable materials as additives in drilling fluids. The objective of this study was to determine whether mandarin peel powder particle size affects the properties of the drilling fluid. In this paper, mandarin peel was used in the form of a dry powder divided into particle sizes smaller than 0.1 mm, and between 0.1 mm and 0.16 mm. Mandarin peel powder was added to a water-based drilling fluid in four different concentrations (0.5, 1, 1.5, and 2% by volume of water). By increasing the mandarin peel powder concentration, the API filtration reduced up to 42%, PPT filtration significantly decreased up to 61.54%, while the rheological parameters generally... [more]

Demagnetization is required to prevent a warship from being detected by magnetic mines. However, minimal research has been conducted to establish a suitable deperming protocol, especially the Flash-D protocol. To establish such a deperming protocol, we conducted a theoretical study using Preisach modeling for the Flash-D protocol. Magnetic coercivity distributions were derived from B−H curves representing the material properties of the warship, and a deperming protocol that is effective on particles was proposed. The internal magnetization distribution was analyzed using the program combined with Preisach model and the finite element method (FEM), in accordance with the conventional and proposed protocols, and the proposed method was confirmed to be effective. In addition, the method was verified through experiments in a scaled-down magnetic treatment facility test room. Therefore, the proposed method can be used to establish an effective Flash-D protocol for submarines depending on th... [more]

The high dependence on imported fuels, the need to reduce greenhouse gas (GHG) emissions and the need to develop a low-carbon economy are reasons for the development of the renewable energy market in Poland. The wider use of biofuels can be a method for reducing oil dependence and reducing CO2 emission. Opportunities to reduce emissions and meet international requirements in the field of environmental protection are seen, among others, in the development of the production and greater use of biocomponents, including bioethanol. This article presents the current state of development in the area of bioethanol production in Poland. An outline of legal regulations in the examined area and statistical data, as well as the largest producers and their production capacity, are presented. The basic time range of analyses covered the years 2015−2019. According to the analyses, liquid biofuels in Poland are used on a small scale, although over 2015−2019, the production of bioethanol as a biocompon... [more]

Recent research studies on industrial cyber-physical systems (ICPSs) have witnessed vast patronage with emphasis on data utility for improved design, maintenance, and high-level decision making. The design of proton-exchange membrane fuel cells (PEMFC) is geared towards improving performance and extending life cycles. More often, material selection of PEMFC components contributes a major determining factor for efficiency and durability with the seal/gasket quality being one of the most critical components. Finite element analysis (FEA) offers a simulated alternative to real-life stress analysis of components and has been employed on different rubber-like gasket materials for hydrogen fuel cells for determining an optimal strain energy density function using different hyperelastic models following uniaxial tensile testing. The results show that the Mooney−Rivlin, Ogden, and Yeoh models were the most fitting model with the best stress−strain fit following a weighted error evaluation crit... [more]

The need to accelerate the innovation and application of the supply chain has been suggested by the State Council of China. To solve the problem of data isolation caused by privacy protection in the power material supply chain, a data traceability and sharing mechanism based on blockchain is designed in this paper. Firstly, the existing problems of the power material supply chain are introduced, and the applicability of blockchain in the power material supply chain in view of these problems is analyzed. Secondly, blockchain-based power material supply deployment and application structures are proposed. Then, considering the problem of data isolation in the material inspection and distribution links between suppliers and the material company, a data traceability mechanism based on blockchain is designed to provide evidence for the data authenticity and a proxy re-encryption method is used to ensure security and privacy in data sharing. Finally, the effectiveness of the proposed data tra... [more]

Alluaudite-type materials are systematically attracting more attention as prospective cathode materials for sodium-ion batteries. It has been demonstrated that optimized thermal nanocrystallization of glassy analogs of various cathode materials may lead to a significant increase in their electrical conductivity. In this paper, three alluaudite-like glasses (Na2Fe3(PO4)3—FFF, Na2VFe2(PO4)3—VFF, and Na2VFeMn(PO4)3—VFM) were synthesized and subjected to an optimized thermal nanocrystallization. This procedure resulted in nanostructured samples with increased electrical conductivity at room temperature: 5×10−7 S/cm (FFF), 7×10−5 S/cm (VFM), and 6×10−4 S/cm (VFF). The nanocrystalline microstructure was also evidenced by ultra-high-frequency impedance spectroscopy (up to 10 GHz) and proposed electrical equivalent circuits. Prototype electrochemical cells were assembled and characterized with voltage cutoffs of 1.5 and 4.5 V. The electrochemical performance was, however, modest. The gravimetr... [more]