Browse
Records Added in April 2023
Records added in April 2023
Change month: January | February | March | April | May | June | July | August | September | October | November | December
8318. LAPSE:2023.27171
Multi-Walled Carbon Nanotubes Supported Pd(II) Complexes: A Supramolecular Approach towards Single-Ion Oxygen Reduction Reaction Catalysts
April 4, 2023 (v1)
Subject: Materials
Keywords: CNTs, heterogeneous catalysis, ORR, palladium catalyst, RRDE, supramolecular interactions, surface adsorption
Lowering the platinum group metal content of oxygen reduction reaction catalysts is among the most prevalent research focuses in the field. This target is herein approached through supported Pd(II) complexes. Starting from a commercial macrocycle, a new ligand is synthesized, its solution behavior and binding properties briefly explored (potentiometry, UV-Vis) and then used to prepare a new catalyst. A supramolecular approach is used in order to obtain homogeneous decoration of carbon nanotubes surfaces, fostering novel possibilities to access single-ion active sites. The novel catalyst is characterized through X-ray photoelectron spectroscopy and scanning transmission electron microscopy and its promising oxygen reduction reaction performance is evaluated via rotating ring-disk electrode and rotating disk electrode in half-cell studies.
8319. LAPSE:2023.27170
Real-Time Energy Management of Parallel Hybrid Electric Vehicles Using Linear Quadratic Regulation
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: energetic macroscopic representation (EMR), energy management strategy (EMS), hardware-in-the-loop (HIL), parallel hybrid electric vehicle (HEV)
Optimization-based methods are of interest for developing energy management strategies due to their high performance for hybrid electric vehicles. However, these methods are often complicated and may require strong computational efforts, which can prevent them from real-world applications. This paper proposes a novel real-time optimization-based torque distribution strategy for a parallel hybrid truck. The strategy aims to minimize the engine fuel consumption while ensuring battery charge-sustaining by using linear quadratic regulation in a closed-loop control scheme. Furthermore, by reformulating the problem, the obtained strategy does not require the information of the engine efficiency map like the previous works in literature. The obtained strategy is simple, straightforward, and therefore easy to be implemented in real-time platforms. The proposed method is evaluated via simulation by comparison to dynamic programming as a benchmark. Furthermore, the real-time ability of the propo... [more]
8320. LAPSE:2023.27169
An Early Warning Method of TCU Failure in Electromagnetic Environment Based on Pattern Matching and Support Vector Regression
April 4, 2023 (v1)
Subject: Environment
Keywords: CST, electromagnetic disturbance, failure mode, SVR, TCU
With the continuous improvement of the voltage level of the power system, the electromagnetic interference problem of the converter station has become more and more serious. The thyristor control unit (TCU) is the core equipment of the converter valve, and its normal operation is related to the safe and stable operation of the entire converter valve. This paper starts with the actual electromagnetic environment in the converter valve hall, analyzes the failure principle of the TCU under electromagnetic disturbance, and observes the electromagnetic field distribution and sensitive components on the circuit board. Then, a TCU failure early warning method based on pattern matching and support vector regression (SVR) is proposed. The failure trend is deduced by constructing an abnormal information vector, and then the failure predictor is constructed using support vector regression optimized by grid search (GS), genetic algorithm (GA), and particle swarm optimization (PSO). Considering the... [more]
8321. LAPSE:2023.27168
Experimental Study of Harmonic Influence on Electrical Energy Metering
April 4, 2023 (v1)
Subject: Energy Management
Keywords: active energy, capacitor banks, electrical energy meters, high harmonics, power quality, reactive energy, total harmonic distortion
The paper considers the influence of harmonics on the operating of electrical energy meters in a network with nonlinear loads. It is shown that electronic static meters of active energy are tested in the presence of distortions, and electronic static meters of reactive energy accuracy requirements do not take into account the possible presence of harmonics. It is revealed that the maximum influence on the error in active energy metering is exerted by the number of harmonics taken into account and their amplitude, and the error in reactive energy metering is additionally influenced by the phase angle at the fundamental and harmonic frequencies, which has been confirmed in laboratory conditions. Additionally, experimental studies of the capacitor bank’s influence on reactive energy metering has been carried out in the presence of nonlinear electrical loads. It is shown that when capacitor banks are connected, the error in reactive energy measurement and variation range of the phase shift... [more]
8322. LAPSE:2023.27167
Analysis of the Correlation between Combustion Products in Biomass Thermal Power Plant Using Association Rule Mining
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: association rule mining, Biomass, combustion products, thermal power plant
The biomass combustion process is inevitably accompanied by the emission of pollutant gasses. This paper gives a comprehensive analysis of the external variables and combustion products of the biomass plant. The analyzed data were collected from 18 MWt boiler in combined heat and power plant Sremska Mitrovica over a period of four months. The correlations between the recorded data were determined using a unique methodology, which is based on association rule mining. The results of the study can be further used for the reduction of the harmful combustion products, as well as for the optimization of the operation process.
8323. LAPSE:2023.27166
The Role of Multiple Injections on Combustion in a Light-Duty PPC Engine
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: internal combustion engines, large eddy simulations, low-temperature combustion, multiple injection strategy, partially premixed combustion, primary reference fuel
This paper presents a numerical investigation of the ignition and combustion process of a primary reference fuel in a partially premixed light-duty internal combustion (PPC) engine. Partially pre-mixed combustion is achieved by employing a multiple injection strategy with three short injection events of fuel pulses. The timing of the first two fuel pulses, 48 and 22 crank angle degrees before top dead center, are chosen with the purpose to stratify the fuel and air charge, whereas the third injection, at five crank angle degrees before top dead center, serves as an actuator of the main heat release. In addition to this baseline injection, three alternative injection strategies are studied, including a split-fuel two-injection strategy and modified triple-injection strategies. Large eddy simulations are employed utilizing a skeletal chemical kinetic mechanism for primary reference fuel capable of capturing the low-temperature ignition and the high temperature combustion. The large eddy... [more]
8324. LAPSE:2023.27165
Combination of Pre-Pulse and Constant Pumping Rate Hydraulic Fracturing for Weakening Hard Coal and Rock Mass
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: constant pumping rate, fractures network, hard coal–rock mass, pulse hydraulic fracturing, top coal weakening
The weakening of hard coal−rock mass is the core common problem that is involved in the top coal weakening in hard and thick coal seams, the hard roof control during the initial mining stage in the longwall mining face, and the hanging roof control in the gob of non-coal mine. Based on the characteristics of pulse hydraulic fracturing and constant pumping rate hydraulic fracturing, a weakening method for hard coal−rock mass by combining pre-pulse and constant pumping rate hydraulic fracturing is proposed. A complete set of equipment for the combined pulse and constant pumping rate hydraulic fracturing construction in the underground coal mine is developed. The pulse and constant pumping rate hydraulic fracturing technology and equipment were applied in the top coal weakening of the shallow buried thick coal seam. Compared with no weakening measures for top coal, the average block size of the top coal caving was reduced by 42% after top coal hydraulic fracturing. The recovery rate of th... [more]
8325. LAPSE:2023.27164
Optimization of a Wood Pellet Boiler System Combined with CO2HPs in a Cold Climate Area in Japan
April 4, 2023 (v1)
Subject: Optimization
Keywords: combined system, heat pump, hot water supply, regional economic ripple effect, wood pellet boiler, woody biomass
Hot water supply is one of the leading consumers of energy in the building sector in cold climate areas. The use of woody biomass is effective in reducing CO2 emissions in hot-water supply systems. This report deals with a system that combines a wood pellet boiler (PB) and a heat pump system with CO2 (CO2HP) that is used in a facility for disabled people. The following research was conducted. The operation of a hybrid system combining a PB and CO2HPs was investigated. While operating the system, four specific operations were developed as countermeasures to save on costs and reduce system troubles while reducing CO2 emissions. The processes and results are introduced. Numerical simulations were carried out to optimize the operation. The hot water temperature, water volume, and hot water loads were simulated. The influence of the water volume ratio on the cost and primary energy consumption under the requirements for safe system operation was studied. The regional economic ripple effects... [more]
8326. LAPSE:2023.27163
Experimental Investigation of Desiccant Dehumidification Cooling System for Climatic Conditions of Multan (Pakistan)
April 4, 2023 (v1)
Subject: Materials
Keywords: air-conditioning, desiccant dehumidification, Maisotsenko cycle, Pakistan, performance evaluation, polymer, silica gel
In this study, experimental apparatus of desiccant dehumidification was developed at lab-scale, using silica gel as a desiccant material. Experimental data were obtained at various ambient air conditions, while focusing the climatic conditions of Multan (Pakistan). A steady-state analysis approach for the desiccant dehumidification process was used, and thereby the slope of desiccant dehumidification line on psychrometric chart (ϕ*) was determined. It has been found that ϕ* = 0.22 in case of silica gel which is lower than the hydrophilic polymeric sorbent, i.e., ϕ* = 0.31. The study proposed two kinds of systems, i.e., (i) standalone desiccant air-conditioning (DAC) and (ii) Maisotsenko-cycle-assisted desiccant air-conditioning (M-DAC) systems. In addition, two kinds of desiccant material (i.e., silica gel and hydrophilic polymeric sorbent) were investigated from the thermodynamic point of view for both system types, using the experimental data and associated results. The study aimed t... [more]
8327. LAPSE:2023.27162
Energy Harvesting towards Self-Powered IoT Devices
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: Batteries, energy harvesting, IoT, photovoltaic, piezoelectric, solar energy, thermal energy, wind energy
The internet of things (IoT) manages a large infrastructure of web-enabled smart devices, small devices that use embedded systems, such as processors, sensors, and communication hardware to collect, send, and elaborate on data acquired from their environment. Thus, from a practical point of view, such devices are composed of power-efficient storage, scalable, and lightweight nodes needing power and batteries to operate. From the above reason, it appears clear that energy harvesting plays an important role in increasing the efficiency and lifetime of IoT devices. Moreover, from acquiring energy by the surrounding operational environment, energy harvesting is important to make the IoT device network more sustainable from the environmental point of view. Different state-of-the-art energy harvesters based on mechanical, aeroelastic, wind, solar, radiofrequency, and pyroelectric mechanisms are discussed in this review article. To reduce the power consumption of the batteries, a vital role i... [more]
8328. LAPSE:2023.27161
Performance of Communication Network for Monitoring Utility Scale Photovoltaic Power Plants
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: communication architecture, Ethernet, IEC 61850 Standard, large scale photovoltaic power plant, wired communication
The grid integration of large scale photovoltaic (PV) power plants represents many challenging tasks for system stability, reliability and power quality due to the intermittent nature of solar radiation and the site accessibility issues where most PV power plants are located over a wide area. In order to enable real-time monitoring and control of large scale PV power plants, reliable two-way communications with low latency are required which provide accurate information for the electrical and environmental parameters as well as enabling the system operator to evaluate the overall performance and identify any abnormal conditions and faults. This work aims to design a communication network architecture for the remote monitoring of large-scale PV power plants based on the IEC 61850 Standard. The proposed architecture consists of three layers: the PV power system layer, the communication network layer, and the application layer. The PV power system layer consists of solar arrays, inverters... [more]
8329. LAPSE:2023.27160
Lumped Kinetics for Homogeneous Reactions of n-Hexadecane and n-Decene as Model Compounds for PE Pyrolysis Primary Tars
April 4, 2023 (v1)
Subject: Modelling and Simulations
Keywords: combustion, lumped kinetics, plastics, pyrolysis, soot, tar
The focus of this paper is to establish a lumped kinetic scheme for secondary reactions of tar produced from pyrolysis of plastics or polymer-based wastes. Notably, the focus is not on the detailed yield of all reaction intermediates and products but on the propensity to form soot. Based on the assumption that that primary tar from pyrolysis of plastic wastes is mostly formed by aliphatics which can undergo progressive aromatization to polycyclic aromatic hydrocarbons (PAHs) and soot, a reaction network with 198 species and 6307 reactions proposed by Ranzi and coworkers was lumped into a very simple five reaction mechanism. The lumped kinetic model has been used to predict PAHs and soot formation in different conditions and proved to be a good alternative to comprehensive kinetic models up for relatively low temperature and short residence times (of up to 1 min at 1200 K, up to 1 s at 1400 K). At higher temperature/longer residence times, the simplified model still provides reasonable... [more]
8330. LAPSE:2023.27159
Sky Luminance Distribution Models: A Comparison with Measurements from a Maritime Desert Region
April 4, 2023 (v1)
Subject: Other
Keywords: daylighting, maritime desert region, sky luminance
The effective use of daylight is a function of the luminance of the sky exposed to the glazing system. Therefore, accurate data about the luminance distribution of the sky are necessary for the optimum use of daylight. This paper compares seven models for estimating the angular sky luminance distribution. They were selected based on the ability to be used with all sky conditions and to determine the luminance of the sky from solar radiation. Measurements of solar radiation, sky luminance, and sky radiance were taken in a “maritime desert region” in Saudi Arabia. The results showed that the “Perez 93” model performed better than the other models tested, but there is a need for more studies to identify more accurate models for use in similar climatic conditions.
8331. LAPSE:2023.27158
Experimental Study on Displacement of Water by Sub-Zero N-Hexanol in a Straight Channel
April 4, 2023 (v1)
Subject: Other
Keywords: cryogenic fracturing, ice blockage, immiscible displacement, water freezing
Series of displacement tests of water by cold n-hexanol (below 0 °C) in a straight tube were conducted to investigate the freezing-accompanied displacement process, which occurs during the cryogenic fracturing process. The interrelationship between water freezing and displacement flow was studied. It was found that the displacement flow could significantly affect the water distribution in the flow channel. Along with the displacement proceeding, the n-hexanol overtook the water in the flow direction gradually, and the water in the center of the channel was driven to the edge area. Moreover, the initially integrated water phase split into several parts during the displacement process. Once the water freezing occurred, two typical ice blockage patterns, i.e., complete ice blockage and incomplete ice blockage, were observed. In incomplete ice blockage pattern, the channel cross-section was partly occupied by the ice phase, which mainly affected the rate of subsequent fluid flow. In comple... [more]
8332. LAPSE:2023.27157
How Population Age Distribution Affects Future Electricity Demand in Korea: Applying Population Polynomial Function
April 4, 2023 (v1)
Subject: Energy Management
Keywords: electricity demand, electricity demand forecast, population age distribution, population aging, population polynomials
Mounting evidence shows that economic and climate variables such as income, energy price, and temperature impact energy demand. We examined another variable, population age distribution, which has rarely been considered, that could affect energy demand. We employ population polynomials to account for the impact of population age distribution on residential electricity consumption in Korea. Using panel data from 1990 to 2016, we verify that populations aged 20~44, and those over 60, raise residential electricity consumption. We additionally evaluate the impact of population age distribution in forecasting future electricity consumption and conclude that age distribution effects dominate total population growth effects.
8333. LAPSE:2023.27156
Analysis and Evaluation of WBG Power Device in High Frequency Induction Heating Application
April 4, 2023 (v1)
Subject: Other
Keywords: evaluation, GaN HEMT, induction heating, performance comparison, SiC MOSFET, WBG device
A device suitability analysis is performed herein by comparing the performance of a silicon carbide (SiC) metal-oxide-semiconductor-field-effect transistor (MOSFET) and a gallium nitride (GaN) high-electron mobility transistor (HEMT), which are wide-bandgap (WBG) power semiconductor devices in induction heating (IH) systems. The WBG device presents advantages such as high-speed switching owing to its excellent physical properties, and when it is applied to the IH system, a high output power can be achieved through high-frequency driving. To exploit these advantages effectively, a suitability analysis comparing SiC and GaN with IH systems is required. In this study, SiC MOSFET and GaN HEMT are applied to the general half-bridge series resonant converter topology, and comparisons of the conduction loss, switching loss, reverse conduction loss, and thermal performance considering the characteristics of the device and the system conditions are performed. Accordingly, the device suitability... [more]
8334. LAPSE:2023.27155
Experimental Study on Blasting Energy Distribution and Utilization Efficiency Using Water Jet Test
April 4, 2023 (v1)
Subject: Other
Keywords: blasting gas, blasting stress wave, borehole constraint, utilization efficiency, water jet
The blasting stress wave and blasting gas generated by explosive blasting are the two main motive powers of rock fragmentation. An experimental method based on water jet test is used to study the energy distribution ratio of blasting stress wave and blasting gas; the utilization efficiency of blasting energy under different borehole constraint conditions is also analyzed. It proves that the blasting stress wave does not cause the water jet, and the blasting gas is the only power of the water column jet. The results show that the energy of the blasting gas and blasting stress wave respectively account for about 64% and 36% of the total energy generated by the explosion of lead azide. The utilization efficiency of the blasting gas energy under strong, medium, and weak constraint conditions is 100%, 80%, and 52%, respectively. The borehole constraint condition is crucial for the effective utilization of blasting energy.
8335. LAPSE:2023.27154
Calorific Power Improvement of Wood by Heat Treatment and Its Relation to Chemical Composition
April 4, 2023 (v1)
Subject: Materials
Keywords: calorific power, chemical composition, correlations, heat treatment
Chemical composition influences the calorific power of wood, mainly due to the calorific power of structural compounds and extractives. Heat treatment changes the chemical composition of treated wood. This work studies the relationship between chemical composition and calorific power improvement by heat treatment. Samples were heat-treated by the ThermoWood process ® for 1 h and 2 h. High heating value (HHV) and chemical composition; lignin, cellulose, hemicelluloses and extractives in dichloromethane, ethanol, and water were determined. The HHV of untreated wood ranged between 18.54−19.92 MJ/kg and increased with heat treatment for all the tested species. A positive linear correlation was found between HHV and Klason lignin (R2 = 0.60). A negative trend was observed for holocellulose, cellulose, and hemicelluloses content against HHV, but with low determination coefficients for linear regression. The best adjust for polysaccharides was found for hemicelluloses content. A positive corr... [more]
8336. LAPSE:2023.27153
Use of Tanδ and Partial Discharge for Evaluating the Cable Termination Assembly
April 4, 2023 (v1)
Subject: Other
Keywords: aging, cable termination, dissipation factor, partial discharge, XLPE cable
It is known that the failure of cable terminations causes power outages and impairs system quality and continuity. Besides, serious economic losses on both the distribution and consumer sides occur. In this study, the dielectric behavior of the cable and the faults caused by the defects in the cable termination under overvoltage has been examined. As test samples, 12 kV XLPE insulated cable is used and they were aged at three (3*U0) and five (5*U0) times the rated voltage. After each aging cycle, dielectric parameters of the cable were measured by an OMIRCRON CPC100/CPTD1 device, and the partial discharge (PD) was measured by an OMICRON MPD600 device. In the measurements, it was observed that the cable was broken down at different aging cycle numbers as a result of defects in the cable termination due to weak workmanship. As a result of the measurements, it is concluded that defects in the cable termination give information about the increase in the probability of failure and the decre... [more]
8337. LAPSE:2023.27152
Comparative Analysis of the Mining Cribs Models Filled with Gangue
April 4, 2023 (v1)
Subject: Other
Keywords: gangue, load-displacement characteristics, pressure-compressibility characteristics, wooden cribs
In the article, comparative laboratory strength tests of three-point and four-point wooden cribs models are presented. In the case of cribs with a triangular cross-section, the notches made at an angle of 60 degrees were used for the first time. The individual beams of the three-point and four-point cribs were stacked horizontally and connected to each other by means of a quick-drying adhesive. The main aim of the research was to compare the empty models with cribs filled with a gangue. In order to better understand the mechanism of behavior of models under loads, load-displacement and pressure-compressibility characteristics are presented. It was found that filling the three-point and four-point crib with gangue increases its maximal load several times compared to the empty cribs.
8338. LAPSE:2023.27151
Viscosity Models for Drilling Fluids—Herschel-Bulkley Parameters and Their Use
April 4, 2023 (v1)
Subject: Modelling and Simulations
Keywords: drilling fluid shear rates, drilling fluid viscosity, Herschel-Bulkley model
An evaluation is presented of the practical usage of the Herschel-Bulkley viscosity model for drilling fluids. If data from automatic viscosity measurements exist, the parameters should be selected from relevant shear rate ranges to be applicable. To be able to be used properly, viscosity measurements must be measured with a sufficient accuracy. It is shown that a manual reading of standard viscometers may yield insufficient accuracy. It is also shown that the use of yield point/plastic viscosity (YP/PV) as measured using API or ISO standards normally provide inaccurate viscosity parameters. The use of the Herschel-Bulkley model using dimensionless shear rates is more suitable than the traditional way of writing this model when the scope is to compare different drilling fluids. This approach makes it also easier to make correlations with thermodynamic quantities like pressure and temperature or chemical or mineralogical compositions of the drilling fluid.
8339. LAPSE:2023.27150
Hygrothermal Analysis of Masonry Wall with Reed Boards as Interior Insulation System
April 4, 2023 (v1)
Subject: Other
Keywords: heating cable, hygrothermal performance, interior insulation, reed insulation
When the masonry walls of buildings under heritage protection need to be restored and thermally improved, the only option is to use an interior insulation system. This is also the riskiest method of insulating walls in cold climates. Capillary active interior insulation systems have been proven to be the most reliable, minimizing the risk of mold growth and decay caused by condensation. They have also been proven to be less risky in wind-driven rain. The building studied is situated in a heritage-conservation area in downtown Tartu, Estonia, and therefore cannot be insulated from the exterior. This paper compares the hygrothermal performance of four different interior insulation systems with and without a heating cable and vapor barrier. In the first case, Isover Vario KM Duplex UV was placed between reed panels. In the second case, reed panels were used without the vapor barrier. Data loggers were applied between the reed panels and the original wall and inside the room to measure tem... [more]
8340. LAPSE:2023.27149
A Contemplation on Electricity Meters In-Service Surveillance Assisted by Remote Error Monitoring
April 4, 2023 (v1)
Subject: Process Monitoring
Keywords: power measurement, remote monitoring, time series analysis, watt-hour meters
In this paper, remote error monitoring techniques for electricity meters are overviewed suggesting their utilization for in-service surveillance assistance. It is discussed that in-service error observation could provide valuable input, contributing to the timely detection of batches of meters reaching nonconformance status. The payback period analysis of the deployment of a remote error monitoring solution is considered. However, it is pointed out that such an analysis lacks input information describing the relationship between the remote monitoring system’s performance and its ability to detect nonconformance of the batch. It is also noticed that there is no published methodology for grading the status of an entire batch of meters referring to error estimates of a subset of the meters, when the uncertainty of estimation is rather high.
8341. LAPSE:2023.27148
Thermal Efficiency of Oxyhydrogen Gas Burner
April 4, 2023 (v1)
Subject: Energy Systems
Keywords: alkaline electrolyzer, oxyhydrogen gas, oxyhydrogen gas burner, thermal efficiency
One of the main methods used to generate thermal energy is the combustion process. Burners are used in both industrial and residential applications of the open combustion process. The use of fuels that reduce polluting gas emissions and costs in industrial and residential processes is currently a topic of significant interest. Hydrogen is considered an attractive fuel for application in combustion systems due to its high energy density, wide flammability range, and only produces water vapor as waste. Compared to research conducted regarding hydrocarbon combustion, studies on hydrogen burners have been limited. This paper presents the design and evaluation of an oxyhydrogen gas burner for the atmospheric combustion process. The gas is generated in situ with an alkaline electrolyzer with a production rate of up to 3 sL min−1. The thermal efficiency of a gas burner is defined as the percentage of the input thermal energy transferred to the desired load with respect to a given time interva... [more]
8342. LAPSE:2023.27147
Thermophysical Properties of 1,1,1,3,3,3-hexafluoro-2-methoxypropane (HFE-356mmz) in the Vapor Phase Measured by Using an Acoustic-Microwave Resonance Technique
April 4, 2023 (v1)
Subject: Materials
Keywords: 1,1,1,3,3,3-hexafluoro-2-methoxypropane (HFE-356mmz), density, dielectric permittivity, dipole moment, heat capacity, molar polarization, sound velocity
Thermophysical properties of HFE-356mmz in the vapor phase were measured by means of an acoustic-microwave resonance method. HFE-356mmz, which is 1,1,1,3,3,3-hexafluoro-2-methoxypropane in chemical name, is expected to be used as a working fluid with low global warming potential for the Organic Rankine cycle (ORC). The sound velocity and dielectric permittivity were simultaneously measured by using a cylindrical acoustic-microwave resonator. The sound velocity data were analyzed to obtain the ideal-gas heat capacity at constant pressure. The integral of the ideal-gas heat capacity as a function of temperature derives the ideal-gas enthalpy, which is a fundamental and important energy property to simulate the thermodynamic cycle. Similarly, the analysis of the dielectric permittivity data leads to information on the ideal-gas molar polarizability, dipole moment, and density. The acquired thermophysical properties of HFE-356mmz were compared to those of R-245fa and n-pentane, which are t... [more]
[0.08 s]

