The development of technologies to improve the performance of photovoltaic (PV) module integrated converters (MICs) is fundamental to increase the use of distributed generation systems with photovoltaic power source in large urban centers, mainly for complex residential roofs. For two-stage PV MICs, high step-up DC-DC converters are required to boost the low PV module voltage to a higher voltage, in order to suit the DC bus voltage requirements of grid-tied inverters. Thus, to support researchers interested in developing DC-DC power conversion for PV microinverters, this paper classifies the DC-DC converters according to their operational and constructive characteristics and presents some elementary voltage-boosting techniques to aid in analyzing and understanding more complex topologies. Finally, high step-up DC-DC converters based on magnetic coupling and switched capacitor widely cited by important works related to PV applications are presented, with their principles of operation an... [more]

Building energy waste has become one of the major challenges confronting the world today, so specifications and targets for building energy efficiency have been put forward in countries around the world in recent years. The schematic design stage matters a lot for building energy efficiency, while most architects nowadays are less likely to make energy efficiency design decisions in this stage due to the lack of necessary means and methods for analysis. An integrated multi-objective multivariate framework for optimization analysis is proposed for the schematic design stage in the paper. Here, the design parameters of the building morphology and the design parameters of the building envelope are integrated for analysis, and an integrated performance prediction model is established for low-rise and medium-rise residential buildings. Then, a comparison of the performance indicators of low-rise and medium-rise residential buildings under five typical urban climatic conditions is carried ou... [more]

The worldwide transformation from fossil fuels to sustainable energy sources will increase the demand for biomass. However, the ash content of many available biomass sources exceeds the limits of national standards. In this study, short-rotation coppice willow biomass was hydrothermally treated at 150, 170 and 185 °C. The higher heating value increased by 2.6% from x¯ = 19,279 J × g−1 to x¯ = 19,793 J × g−1 at 185 °C treatment temperature. The mean ash content was reduced by 53% from x¯ = 1.97% to x¯ = 0.93% at 170 °C treatment temperature, which was below the limit for category TW1b of the European pellet standard for thermally treated biomass. The nitrogen, sulfur and cadmium concentrations were reduced below the limits for category TW1b of the European biomass pellet standard (N: from 0.52% to 0.34%, limit at 0.5%; S: from 0.051% to 0.024%, limit at 0.04%; Cd: from 0.83 mg × kg−1 to 0.37 mg × kg−1, limit at 0.5 mg × kg−1). The highest reduction rates were sampled for phosphor (80−84... [more]

Hotels emit large amounts of CO2 when providing services. Carbon neutrality objectives and the growth of homestays have forced hotel managers to pay more attention to carbon reduction. First, this paper adopted the input−output method to calculate hotel CO2 emissions. It was found that the amount of CO2 emissions in the hotel industry decreased from the year of 2016 to 2018, and there are structural differences in the CO2 emissions of the hotel industry in China. Furthermore, this paper adopted the three-stage SBM-DEA model to evaluate hotel CO2 emission efficiency in 30 provinces in China. The results show that CO2 emission efficiency increased significantly when environmental factors were eliminated. A close observation of different regions shows that the eastern region has a higher CO2 emission efficiency than the western and middle regions. The emergence of homestays has led to increased input slacks in the labor and energy consumption of hotels, which has a negative effect on effi... [more]

In the era of globalization and rapid economic growth, affecting most world economies, increased production and consumption are leading to higher levels of energy production and consumption. The growing demand for energy means that energy resources from conventional sources are not sufficient; moreover, its production generates high costs and contributes to the emission of greenhouse gases and waste. In view of the above, many countries have opted to implement an energy transformation. The energy transition allows the transition from an energy system based on conventional fuels to an energy system based mainly on renewable energy (RE) and low-emission sources. In the EU, the development of a “green economy” has become a strategic goal in the fight against climate change. The development of RE offers the possibility to improve the energy security of a given country and the entire EU. New, innovative technologies of RE also increase the attractiveness and competitiveness of the economies... [more]

Renewable energy has a crucial role in facing climate change. One promising strategy is the creation of energy communities that require active involvement from a bottom-up perspective. Their implementation is difficult, as they currently rely on local policies, community readiness, and technological availability. The objective of this paper is to provide a qualitative overview of energy community concepts and strategies at the European level. The aim is to identify common approaches that are framing the development of energy communities, and to understand the most successful steps leading to their creation and growth. To achieve this objective, a threefold methodology is provided: (1) an updated review on policies dealing with energy communities at the European and Italian level; (2) a qualitative overview of European-funded projects under the Horizon 2020 work program; and (3) a qualitative overview of some of the most successful existing energy communities in Europe. The results outl... [more]

Elevated emissions of hydrogen chloride (HCl) from the combustion of biomass in utility boilers are a major issue because they can cause corrosion problems and deposit molten alkali chloride salts on boilers’ water tubes, resulting in further corrosion. Pyrolysis is a good pre-treatment for solving this problem. This work conducted pyrolysis and co-pyrolysis of pulverized corn straw and lignite coal in a horizontal muffle furnace, with compositions typical of power plant combustion effluents (5% O2, 15% CO2, 80% N2) at different temperatures. Cl compounds were monitored in fuel, flue gas, and solid production of pyrolysis. The co-pyrolysis significantly affected Cl release from fuel. Cl release from corn straw into fuel gas was reduced during biomass co-pyrolysis with lignite. Co-pyrolysis had little influence on the release of organic Cl and KCl. Furthermore, at moderate-temperature pyrolysis, O2 promoted HCl release, when compared with pyrolysis under a N2 atmosphere.

The Paris Agreement requires building retrofitting practices to be more efficient and effective. However, the current practice for building energy retrofitting is lacking behind, and one reason for that is the time-consuming process of energy credit evaluation. Energy performance assessment such as BREEAM-NL in the Netherlands could apply a more automatic approach with the help of building information modelling (BIM) for an efficient building energy retrofitting evaluation process. However, to what extent BIM can help in accelerating energy performance evaluation in the BREEAM-NL certification process is under-examined. This paper first combines literature findings with practical interviews from a case study organization to present a holistic overview of the potential for automating energy-related credits evaluation in BREEAM-NL using BIM. To understand the possible impacts of such transition, a responsible, accountable, consulted, and informed (RACI) matrix is developed to map the imp... [more]

With possible new use cases and demanding requirements of future 5th generation (5G) and beyond cellular networks, the future of mobile communications sounds promising. However, the propagation medium has been considered a randomly acting agent between the transmitter and the receiver. With the advent of the digital age of wireless communications, the received signal quality is degrading due to the uncontrollable interactions of the transmitted radio waves with the surrounding artifacts. This paper presents a comprehensive literature review on reconfigurable intelligent surfaces (RISs) and assisted application areas. With the RIS, the network operators can control radio waves’ scattering, reflection, and refraction characteristics by resolving the harmful properties of environmental wireless propagation. Further, the RIS can effectively control the wavefront, such as amplitude, phase, frequency, and even polarization, without requiring complex encoding, decoding, or radio wave processi... [more]

The Brushless Doubly Fed Reluctance Machine (BDFRM) is an emerging alternative for variable speed drive systems, providing a significant downsizing of the power electronics converter. This paper proposes a new view on the machine equations, allowing the reuse of the standard control system design for conventional synchronous and asynchronous machines: a cascade control system with an inner current control- and outer speed control loop. The assumptions and simplifications made on the machine model allow for a simple, model-based approach to set the controller gains in a brushless doubly fed machine drive system. The cascade control scheme is combined with an Unscented Kalman Filter as a state observer, capable of estimating the load torque and losses. The performance of the proposed control system design is checked in simulation and tested in real-time on a low power BDFRM prototype.

Accurate computation of the performance of a horizontal-axis wind turbine (HAWT) using Blade Element Momentum (BEM) based codes requires good quality aerodynamic characteristics of airfoils. This paper shows a numerical investigation of transitional flow over the DU 91-W2-250 airfoil with chord-based Reynolds number ranging from 3 × 106 to 6 × 106. The primary goal of the present paper is to validate the unsteady Reynolds averaged Navier-Stokes (URANS) approach together with the four-equation transition SST turbulence model with experimental data from a wind tunnel. The main computational fluid dynamics (CFD) code used in this work was ANSYS Fluent. For comparison, two more CFD codes with the Transition SST model were used: FLOWer and STAR-CCM +. The obtained airfoil characteristics were also compared with the results of fully turbulent models published in other works. The XFOIL approach was also used in this work for comparison. The aerodynamic force coefficients obtained with the Tra... [more]

In the power and heat sectors, the uncertainty of energy and carbon prices plays a decisive role in the rationale for decommissioning/repurposing coal-fired CHP (combined heat and power) systems and on investment decisions of energy storage units. Therefore, there is a growing need for advanced methods that incorporate the stochastic disturbances of energy and carbon emission prices into the optimization process of an energy system. In this context, this paper proposes an integrated method for investigating the effects of uncertain energy and carbon prices on the operational patterns and financial results of CHP systems with thermal energy storage units. The approach combines mathematical programming and Monte Carlo simulation. The computational process generates feasible solutions for profit maximization considering the technical constraints of the CHP system and the variation of energy and carbon emission prices. Four scenarios are established to compare the operational patterns and... [more]

For vessel-based transport of liquid CO2 in carbon capture and storage chains, transport at 8 bar(a) enable significant cost reductions compared to transport at higher pressures for most transport distances and volumes. Transport at even lower pressures could further reduce the costs. There are, however, concerns related to dry ice formation and potential clogging in parts of the chain that could lead to operational issues when operating close to the triple point pressure of CO2. In this paper, results from an experimental campaign to de-risk and gain operational experience from the low-pressure CO2 liquefaction process are described. Six experiments using pure CO2 or CO2/N2 mixtures are presented. In four of the experiments, the liquid product pressure was continuously lowered until dry ice was detected and eventually clogged the system. In the final two experiments, the liquefaction process was run in steady-state at low liquefaction pressures for five hours to ensure that there is n... [more]

Energy-related investments gain increasing attention nowadays, particularly in Poland due to clean-energy investment needed to limit greenhouse gas emissions (GHG) and counteract climate change. However, economic appraisal is problematic: the longevity of impacts inextricably involves intergenerational ethical considerations. A crucial parameter is the choice of a discount rate. The predominant approach to estimate the discount rate in EU countries is the Ramsey rule, based on macroeconomic data, but not referring directly to society’s preferences. Those are considered by studies using surveys to elicit individual discount rates (IDR), but rarely concentrating on intergenerational time frame. The paper aims at delivering an insight into the intergenerational intertemporal preferences for Poland (households, n = 471) focusing on whether respondents are willing to declare zero discount rate intergenerationally and whether their choices differ between the short- and long-term perspectives... [more]

Earth-to-air heat exchangers (EAHEs) can be used in the ventilation systems of various types of buildings. Multipipe structures can be found in large-volume buildings, yet scientific analysis of such systems is rare. Annual energy gains and electricity consumption for equivalent single-pipe and multipipe systems are typically not available. This paper bridges this gap, presenting the results of experimental studies on pressure losses in three-, five- and seven-pipe EAHEs and analysis for the annual energy gains and electric energy consumption as compared to a single-pipe exchanger. The results showed that the multipipe EAHE can be successfully replaced by a single-pipe structure with the same thermal performance and similar pressure losses if a tube with the appropriate diameter is used. However, multipipe heat exchangers can also use pipes of larger diameter (manifolds and/or branches), which improves their energy efficiency and may then make them more advantageous than single-pipe st... [more]

At the beginning of 2020, the Strategy of the Republic of Croatia until 2030 with an outlook to 2050 was adopted. The Strategy analyzes two energy transition scenarios, the accelerated energy transition and the moderate energy transition. The Strategy is guided and defined by goals set out by the European Union (EU), which primarily states to decrease greenhouse gas emissions and increase the share of renewable energy sources. In order to reach these goals, it is necessary to substitute fossil fuel capacities with new capacities for the production of electricity from renewable sources. In order to do so, a new wave of investments is needed. The Strategy does not detail the macroeconomic effects of investments in renewable sources on the Croatian economy, generally quantified through GDP growth and employment. This paper analyzes the macroeconomic effects of announced investments in renewable energy sources for electricity production. The analysis encompasses the time period 2021−2030.... [more]

The article presents an active bridge system that enables the solution of a significant problem consisting in ensuring correct indications of temperature values in a wide measuring range for a Pt100 temperature sensor with properties defined by the standard (EN-60751 + A2). The presented active bridge system combines the properties of the measuring amplifier with the stabilization of the current value in the branch in which the Pt100 sensor was placed. The article focuses on the comparison of the temperature measurement in a typical resistance bridge and the measurement made in the developed active bridge, which has also become the subject of a patent. For the performed tests, in which the correctness of the temperature measurement system operation was verified, and on the basis of the obtained results, the quality of temperature measurements was compared in a wide range of changes.

One of the strategic objectives of the European Union is a reduction in greenhouse gas emissions and improvement of energy efficiency by at least 32.5% in different areas of the economy by 2030. However, little is known about the impact of payment in retail on energy consumption. The purpose of this paper is to assess the chain of losses of time and energy, and therefore financial losses, that occur due to the imperfection of payment infrastructure and instruments using data of cashiers’ working time. The research is based on a regression analysis method, where the energy cost per payment transaction is considered in this study as a function of the number of customers per hour and the energy cost. The results of the panel models highlight that the number of customers per hour has a negative impact on the cost of energy per payment transaction. Furthermore, modern means and methods of payment, including cryptocurrencies, do not solve the problem of the excessive time that it takes to se... [more]

This article deals with the prosumer behavior, specifically on an on-grid electrical network that is connected to a larger synchronous electrical network, as well as an off-grid system. In the Simulink (Matlab) application, two models were constructed for this purpose. The modeling of the operation of the electrical network’s on-grid system takes place in one of the models. The simulation of the operation of the electrical network’s off-grid system takes place in the other. We examined the model’s behavior in the provided simulated period from the standpoint of transient states and qualitative indicators of electrical energy under various connection configurations in both systems. The simulations resulted in the possibility of incorporating new sources of energy accumulation, such as pumped storage hydropower plants based on energy storage systems (ESSs), and modifying the model to the user’s needs.

In order to increase the overall solar energy gain of evacuated tube collectors, rear-side reflectors are used. In this way, the otherwise unused incident radiation between the tubes can be reflected back to the absorber, and the performance of the collector can be improved. In this paper, the use of a low-cost, diffusely reflecting, trapezoidal roof covering made from a galvanized metal sheet is investigated and compared to a high-quality, specularly reflecting plane reflector made of aluminum. For this purpose, ray-tracing analysis and TRNSYS simulations were carried out. In the ray-tracing analysis, the experimentally determined zero-loss collector efficiency η0 as well as the incident angle modifiers for each reflector can be reproduced with an error lower than 7.5%. Thermal system simulations show that the performance of both reflectors is comparable. The use of the low-cost reflector leads to an increase in annual collector output of around 30% compared to an increase with the sp... [more]

Power system health prognosis is a key process of condition-based maintenance. For the problem of large error in the residual lifetime prognosis of a power system, a novel residual lifetime prognosis model based on a high-order hidden semi-Markov model (HOHSMM) is proposed. First, HOHSMM is developed based on the hidden semi-Markov model (HSMM). An order reduction method and a composite node mechanism of HOHSMM based on permutation are proposed. The health state transition matrix and observation matrix are improved accordingly. The high-order model is transformed into the corresponding first-order model, and more node dependency information is stored in the parameter group to be estimated. Secondly, in order to estimate the parameters and optimize the structure of the proposed model, an intelligent optimization algorithm group is used instead of the expectation−maximization (EM) algorithm. Thus, the simplification of the topology of the high-order model by the intelligent optimization... [more]

Energy conservation is a popular topic in scientific research today, despite the specific effects of energy conservation awareness still being investigated. Significant research about this topic has been performed in different countries. However, the research conducted so far concerns methods of energy saving, a building’s energy efficiency and new technologies; however, a significant part of society will live in technologically old buildings for a long time, which requires the involvement of consumers to save energy. To explain how energy-saving awareness plays a role in energy-saving behavior, this study will take city dwellers as a research facility and integrate relevant literature and disciplines, such as information and knowledge management, with the mechanistic study of how energy-saving awareness influences behavior that conserves energy and establishes a sensible behavior model. The survey was conducted in Poland, Portugal and Italy with over 18,000 people who declared that th... [more]

Numerical simulation of multiple components in turbomachinery applications is very CPU-demanding but remains necessary in the majority of cases to capture the proper coupling and a reliable flow prediction. During a design phase, the cost of simulation is, however, an important criterion which often defines the numerical methods to be used. In this context, the use of realistic boundary conditions capable of accurately reproducing the coupling between components is of great interest. With this in mind, this paper presents a method able to generate more realistic boundary conditions for isolated turbine large-eddy simulation (LES) while exploiting an available integrated combustion chamber/turbine LES. The unsteady boundary conditions to be used at the inflow of the isolated turbine LES are built from the modal decomposition of the database recorded at the interface between the two components of the integrated LES simulation. Given the reference LES database, the reconstructed field bou... [more]

This article addresses the problem of estimating the potential economic and environmental gains for utility grids of shifting the electric-vehicle (EV) charging time and location. The current literature on shifting EV charging loads has been limited by real-world data availability and has typically therefore relied on simulated studies. Collaborating with a large automobile company and a major utility grid operator in California, this research used actual EV operational data and grid-operation data including locational marginal prices, marginal-grid-emission-rate data, and renewable-energy-generation ratio information. With assumptions about the future potential availability of EV charging stations, this research estimated the maximum potential gains in the economic and environmental performance of the electrical-grid operation by optimizing the time and location of EV charging. For the problem of rescheduling the charging sessions, the optimization models and objective functions were... [more]

This paper presents a description and the results of simulations and laboratory tests of proposed methods for dependent torque control in a Switched Reluctance Motor (SRM). The proposed methods are based on Dependent Torque Motor Control (Rising Slope), DTMC(RC), and Dependent Torque Motor Control (Falling Slope), DTMC(FC). The results of these studies were compared with those on the Classical Torque Motor Control (CTMC) method. Studies were conducted for each of the analyzed control methods by determining the efficiency of the drive and the RMS of the source current and analyzing the vibrations generated for each of the control methods. The harmonics of the phase currents, which caused an increase in the level of vibrations generated, were determined. The usefulness of the proposed methods for controlling SRMs was assessed based on simulations and experiments. Additionally, the natural frequencies of the stator of the tested SRM were determined by a simulation using the Ansys Maxwell... [more]