In this study, the human exposure to the magnetic field emitted by a wireless power transfer (WPT) system during the static recharging operations of a compact electric vehicle (EV) is evaluated. Specifically, the influence of the posture of realistic anatomical models, both in standing and lying positions, either inside or outside the EV, is considered. Aligned and misaligned coil configurations of the WPT system placed both in the rear and front position of the car floor are considered as well. Compliance with safety standards and guidelines has proven that reference levels are exceeded in the extreme case of a person lying on the floor with a hand close to the WPT coils, whereas the system is always compliant with the basic restrictions, at least for the considered scenarios.

Fiscal sustainability is an issue of great concern for governments globally and air pollution control has become an important factor affecting fiscal sustainability. This study aims to examine the impact of air pollution on fiscal sustainability in the short and long run. We conducted an empirical analysis based on air pollution and local government debt data on China’s prefecture-level cities in 2014−2019, using regression discontinuity design (RDD) and a panel data model. The results show that air pollution reduces the debt burden of governments in the short run. However, in the long run, addressing the negative impacts of air pollution adds to the debt burden of local governments, hindering fiscal sustainability. Fiscal freedom and the level of public services significantly moderate the negative impact of air pollution on fiscal sustainability. A higher level of fiscal freedom generally indicates a greater incentive for local governments to raise pollutant emission standards, streng... [more]

As the wind power market grows rapidly, the importance of technology for real-time monitoring and diagnosis of wind turbines is increasing. However, most of the developed technologies and research mainly focus on large horizontal-axis wind turbines, and research conducted on small- and medium-sized wind turbines is rare. In this study, a novel low-cost and real-time health monitoring and diagnosis system for the small H-type Darrieus vertical axis wind turbine is proposed. Turbine operating conditions were classified into parked/idle and power production. In the case of the power production condition, abnormality diagnosis was performed using key monitoring parameters, including vibration, fundamental frequency, the bending stress of the tower and generator vibration. The turbine abnormalities were diagnosed in two stages by applying the alert and alarm limits, determined by referring to international standards and material properties and the long-term measurement data together.

Plastics are one of the basic construction materials with a wide range of various applications. One of their disadvantages is the problem of managing the waste they generate. Chemical recycling offers the possibility of liquefying polymeric waste and using it as fuel components. Existing technologies giving good quality products are expensive. The HT technology developed and described by the authors is cheaper and enables a high quality product to be obtained. The authors have shown that the quality of the received fuel components is influenced not only by the polymer waste processing technology, but also by the feedstock composition. The presented thermolysis technology not only enables more advanced recycling, but also gives the possibility of partial improvement of the product quality. A product with the best physico-chemical properties was obtained from a blend of PE:PP:PS used in the ratio 60:30:10. It was proved that diesel and petrol blends composed of a 5% v/v share of petrol a... [more]

The importance of reducing discomfort glare during the dynamic development of high luminance LEDs is growing fast. Smart control systems also offer great opportunities to reduce electricity consumption for lighting purposes. Currently, dynamic “intelligent” lighting systems are a rapidly developing field. These systems, consisting of cameras and lighting units, such as moving heads or multimedia projectors, are powerful tools that provide a lot of opportunities. The aim of this research is to demonstrate the possibilities of using the projection light in dynamic lighting systems that enable the reduction of discomfort glare and the light pollution phenomenon. The proposed system allows darkening or reducing the luminance of some sensitive zones, such as the eyes or the head, in real-time. This paper explores the development of the markerless object tracking system. The precise identification of the position and geometry of objects and the human figure is used for dynamic lighting and m... [more]

Selecting an appropriate contractor is a crucial phase that clients normally conduct to execute projects. Extensive research has been conducted on the main contractor selection criteria such as financial stability and technical and management capability. However, few studies focusing on health and safety criteria are being used to assess contractors’ safety performance in the existing selection process. Hence, this paper aims to analyse the existing literature on health and safety criteria for contractor selection in construction. The articles were retrieved using developed search string from renowned databases such as Scopus, Ebscohost, Web of Science, Science Direct and Dimensions. This search resulted in a total of 38 papers which can be systematically reviewed. Six main themes were discovered to represent safety prequalification criteria for construction projects, namely, experience and work history, safety control system, safety policy and management, accident rates and records, s... [more]

Due to the constant trend of building wind turbine sets and photovoltaic cells, the so-called renewable energy sources, it is important to develop a mathematical model that will allow us to analyse the economic viability of their operation. By using this model, multivariate calculations should be carried out and developed in the form of universal nomograms that will allow us to estimate this viability almost on an immediate basis. In this paper, such a model for the unit cost of electricity production from renewable energy sources is presented. It is based on a continuous-time Net Present Value notation. The multi-variant calculations performed with it take into account different subsidy levels and operating time of the renewable energy sources. The paper presents values of unit costs of electricity production from renewable energy sources and values of maximum subsidies for this production. It turns out that subsidies are necessary for renewable energy sources to exist on the energy m... [more]

The major objective of this study is to identify and analyze cultural and economic barriers to sustained adoption of LPG (liquefied petroleum gas) as the primary clean cooking energy in India, and examining underpinning values and norms in socio-technical energy system of the country. In 2016, the Government of India introduced a mega scheme called Ujjwala for clean cooking energy with LPG connects in women’s name. This policy, however, experienced limited implementation, but did lead to enhancing women’s agency in many areas. Women’s agency is defined briefly as their ability to set goals, develop capacities, and act on their defined goals to realize desired outcomes in wellbeing and capabilities. In the case of switching to clean cooking energy, the question can be posed as: as women are the ones who carry out most of the onerous work of collecting and cooking with wood, are they able to make decisions on the adoption of clean cooking fuel, that enhance their agency and the wellbeing... [more]

The policies against climate change require the reduction of greenhouse gas emissions of marine transportation. To reach the planned goals, the most promising approach is working both on ships improvement and ports redesign. The latter must enable the new green ships supply with sustainable electrical energy, by integrating shore connection systems, local renewables, and energy storage systems. In this paper, a methodology to obtain such an objective is proposed, capable of taking into account both ships’ and ports’ characteristics. The methodology workflow is explained through a case study, where two shore connection power sizes and two different operative approaches for recharging the ship onboard energy storage are considered. A discussion about the most suitable energy storage technologies is also provided. The case study shows how the methodology can be applied, as well as demonstrating that the port infrastructure has a direct effect on the ship environmental performance.

Brattice walls in mine shafts are used for various purposes, for example, permanent brattice walls can be used to separate ventilation sections. They can be also used in the case of modernization of the hoisting system, as it is in Shaft no. 1 of the Szczygłowice department, part of the Knurów-Szczyłowice coal mine. To shorten the time and reduce costs of the hoist modernization, the shaft is to be partitioned into two sections—with the hoist operating in one of them and another one being modernized in the other section. The new construction of the light brattice wall was designed for this purpose. To prove its usefulness and safety it was tested in the laboratory and computer simulations. The following paper presents CFD simulations of the brattice—its methodology and results together with an overview of works to be conducted in the shaft.

Transient stability assessment (TSA) has always been a fundamental means for ensuring the secure and stable operation of power systems. Due to the integration of new elements such as power electronics, electric vehicles and renewable power generations, dynamic characteristics of power systems are becoming more and more complex, which makes TSA an increasingly urgent task. Since traditional time-domain simulations and direct method cannot meet the actual operation requirements of power systems, data-driven TSA has attracted growing attention from both academia and industry. This paper makes a comprehensive review from the following four aspects: feature extraction and selection, model construction, online learning and rule extraction; and then, summarizes the challenges and prospects for future research; finally, draws the conclusions of this review. This review will be beneficial for relevant researchers to better understand the research status, key technologies, and existing challenge... [more]

The cold chain is responsible for perishable products preservation and transportation, maintaining a proper temperature to slow biological decay processes. Often the efficiency of the cold chain is less than ideal, significantly increasing food waste and energy consumption. Refrigerated transport is a critical phase of the cold chain because of its negative impact on energy consumption and greenhouse gas emissions. It is estimated that around 15% of global fossil fuel energy is used in the refrigerated transport sector, so there has been a growing interest in the last decades in the optimization of these systems in order to reduce their environmental impact. Vapor compression refrigeration units, usually powered by means of a diesel engine, are the most commonly used systems in road refrigerated transport. This paper provides a review of (a) currently used systems and alternative technologies that could reduce the environmental impacts of road refrigerated transport and (b) optimizatio... [more]

The study presents a novel event-triggered quasi-sliding mode control algorithm for linear discrete time systems. The problem is divided into two main parts. Firstly, the sliding mode control of perturbed discrete time systems is considered. In order to limit the impact of external disturbances to one sampling step only, a reference trajectory-based control law is introduced. The proposed control method drives the system’s representative point to an a priori designed reference position in each control step, thus minimizing the influence of disturbance and improving the robustness. Moreover, the reference trajectory is generated according to a novel reaching law, which ensures the nonswitching movement within the quasi-sliding mode band. In the latter part of the study, the proposed control strategy is supplemented with an event-triggering algorithm. In the modified strategy the control signal is only updated when a certain triggering condition occurs. Therefore, the need for communicat... [more]

In alcohol distilleries, the amount of distillery stillage generated can be up to 15 times larger than the amount of alcohol produced. The stillage has high concentrations of organics and nitrogen, a low pH, and a dark brown color. Currently, stillage is mainly used for soil fertilization. For this purpose, it requires thickening and is used seasonally, which creates storage problems and transport costs. To reduce environmental pollution, physicochemical and biological processes have been employed for the treatment of distillery stillage. However, according to bioeconomy principles, the stillage should be transformed into value-added products. Therefore, this review paper focuses on methods of stillage processing that enable energy recovery. Due to its high content of organic compounds, stillage is often used as a raw material for biogas production. Accordingly, anaerobic digestion of stillage is discussed, including an overview of the bioreactors used and the effects of operational pa... [more]

Distributed Energy Storage Systems are considered key enablers in the transition from the traditional centralized power system to a smarter, autonomous, and decentralized system operating mostly on renewable energy. The control of distributed energy storage involves the coordinated management of many smaller energy storages, typically embedded within microgrids. As such, there has been much recent interest related to controlling aspects of supporting power-sharing balance and sustainability, increasing system resilience and reliability, and balancing distributed state of charge. This paper presents a comprehensive review of decentralized, centralized, multiagent, and intelligent control strategies that have been proposed to control and manage distributed energy storage. It also highlights the potential range of services that can be provided by these storages, their control complications, and proposed solutions. Specific focus on control strategies based upon multiagent communication an... [more]

It is because of competencies that there is a possibility of ensuring the strategic safety of each country when it comes to energy security. With the vast development of IT and teamwork, there are various competencies needed in the whole energy sector. The aim of this study is to assess the needs of competencies in the Polish energy labor market as well as the trends among hard ad soft skills also in the context of renewable energy sources. Within an exploratory approach, 245 job advertisements were analyzed using various tools, including general descriptive statistics, Shapiro-Wilk, Kruskal−Wallis H and Mann−Whitney U tests, as well as Spearman’s Rho. The research confirmed that teamwork and MS Office are crucial demands of employers. It is also important that the market is diverse when it comes to competence demands, but soft skills are needed in every position, even purely technical ones.

Large eddy simulations on film cooling hole array on a flat plate was carried out to investigate upstream turbulence effect. Circular cylinders were configured to create a turbulent boundary layer and its diameter has been adjusted to generate 13% upstream turbulence intensity in the main flow. Due to the small pitch to diameter configuration of the cylinder, two-dimensional LES analysis was carried out in advance and the results showed that LES was an essential method to resolve flow field around and downstream circular cylinder, which was not available in RANS simulations. The three-dimensional LES results showed reasonable agreement in turbulence intensity and normalized velocity distributions along the vertical with measured data. According to the blowing ratio, the cooling flow coverage on the surface along the stream-wise direction was varied and well agreed with measured data. Additionally, upstream boundary flows were partially ingested inside the cooling hole and discharged ag... [more]

Natural dimension stone processing generates large volumes of stone waste, which have a significant impact on the environment, as well as on the efficiency and profitability of the stone-processing plant. The article presents the characteristics of waste produced as a result of natural dimension stone processing and the structure of the waste production process. Solid stone scraps and sludge were distinguished. On the basis of the performed analyses, it was shown that stone waste constitutes 10−35% in relation to the quantity of the processed stone material, with the quantity of sludge being even threefold greater than the volume of solid scraps. According to the circular economy principles, the aim should be to reduce the amount of waste generated by reducing primary resources in favour of secondary material. Reducing the volume of stone waste is possible through rational planning of stone production while at the same time maximising the efficiency of stone material usage and introduc... [more]

Adsorption chillers with desalination functionality, being devices characterised by very low electricity consumption, provide an alternative to conventional sources of cooling and water. The option of desalinating water means that the use of a single device enables obtaining two useful products. Adsorption chillers are not widely used at present. due to their low performance characteristics; these are, however, constantly being improved. This paper presents a verification of the possibility of increasing the cooling coefficient of performance (COP) and specific cooling power (SCP) of a laboratory adsorption chiller by optimising the length of cycle times and using a copper additive to silica gel with a mass fraction of 15% to increase heat transport in the bed. The choice of copper among other considered additives was determined by the conclusions from the research on the sorption kinetics of various mixtures, price and availability, and a high thermal conductivity. The device was oper... [more]

It is normally accepted that Battery Energy Storage Systems improve frequency regulation by providing fast response to the Automatic Generation Control. However, currently available control strategies may lead to early Energy Storage Systems aging given that Automatic Generation Control requirements are increasing due to zero carbon power generation integration. In this sense, it is important to analyze the aging phenomena in order to assess the technical−economical usefulness of Battery Energy Storage Systems towards zero carbon power systems. In order to avoid early aging, various proposals on aging-reducing algorithms can be found; however, it is unclear if those aging-reducing algorithms affect the performance of Battery Energy Storage Systems. It is also unclear whether those effects must be internalized to properly dimension the capacity of Battery Energy Storage Systems to both comply with performance standards and to prevent early aging. Thus, this paper estimates the storage c... [more]

In the past few decades, extensive studies have been performed to utilize the solar energy for photocatalytic water splitting; however, up to the present, the overall efficiencies reported in the literature are still unsatisfactory for commercialization. The crucial element of this challenging concept is the proper selection and design of photocatalytic material to enable significant extension of practical application perspectives. One of the important features in describing photocatalysts, although underestimated, is particle morphology. Accordingly, this review presents the advances achieved in the design of photocatalysts that are dedicated to hydrogen generation, with an emphasis on the particle morphology and its potential correlation with the overall reaction performance. The novel concept of this work—with the content presented in a clear and logical way—is based on the division into five parts according to dimensional arrangement groups of 0D, 1D, 2D, 3D, and combined systems.... [more]

The maximum gasification rate of corn stalk char (CSC) appeared at high conversion range, and its quite different gasification behaviors from other carbonaceous materials are all derived from the catalytic effect of alkali and alkali earth metals (AAEMs), so it is necessary to study the effect of AAEMs and gasification kinetics of such biomass char. However, there are few systematic discussions about this effect and kinetic modeling. Thus, in this study, CSC samples were prepared in a fast pyrolysis fixed-bed reactor, and its gasification experiments were conducted on a pressurized magnetic suspension balance at various total pressures (0.1−0.7 MPa), steam concentrations (10−70 vol.%) and temperatures (725−900 °C). Moreover, a water-leached CSC (H2O-CSC) was also prepared to evaluate the impact of AAEMs on the gasification performance of CSC, and some well-known models were adopted to describe the gasification behaviors. On the basis of these results, the effect of primary AAEMs on the... [more]

The process of technology management contains various stages, such as the identification, selection, acquisition, implementation, and maintenance of technologies. In the case of power generation companies, a key aspect of the selection stage is the choice of generation technologies for newly commissioned units. The investment decision depends on many factors, primarily economic, environmental, social, technological, and legal, and represents a complex multi-criteria problem. Currently, the decision is further complicated by the often unpredictable tightening of environmental standards, forcing the closure of conventional sources, on which many countries have so far based their energy security. The paper analyzes the problem of choosing one of the so-called clean coal technologies to be implemented in conditions of transformation of the power sector. In this paper, five selected clean coal technologies are characterized, and the SMART method is adopted to technology selection. The follo... [more]

Protection against the electromagnetic fields around high-voltage transmission lines is an issue of great importance, especially in the case of buildings near power lines. Indeed, the developed fields can be harmful for the habitants and electrical/electronic devices, so the implementation of appropriate measures to address the above electromagnetic interference issue is necessary in order to ensure the safety of both human beings and equipment. Several practices have been proposed to reduce the electric and the magnetic fields around overhead and underground transmission lines (minimum distance, shielded cables, anechoic chamber etc.). In this context, the scope of the current paper is the use of highly permeable magnetic sheets for shielding purposes, along with the development of an appropriate procedure, based on finite element analysis (FEA) for the efficient design of passive shielding. The simulation results are compared with laboratory measurements in order to confirm the adequ... [more]

Understanding the carbon dioxide (CO2) solubility in formation brines is of great importance to several industrial applications, including CO2 sequestration and some CO2 capture technologies, as well as CO2-based enhanced hydrocarbon recovery methods. Despite years of study, there are few literature data on CO2 solubility for the low salinity range. Thus, in this study, the solubility of CO2 in distilled water and aqueous ionic solutions of NaCl, MgCl2, CaCl2 and MgCl2 + CaCl2 were obtained in a low salinity range (0−15,000 ppm) at temperatures from 298−373 K and pressures up to 20 MPa using an accurate and unconventional method called potentiometric titration. An experimental data set of 553 data points was collected using this method. The results of the experiments demonstrate that increasing pressure increases the solubility of CO2 in various brines, whereas increasing temperature and salinity reduces the solubility. The role of different ions in changing the solubility is elaborate... [more]