Electronic devices can be damaged in an undesirable manner if the junction temperature achieves high values in order to cause thermal runaway and melting. This paper describes the mathematical model to calculate the power losses in power semiconductor devices used in bidirectional rectifier which supplies a resistive-inductive load. The obtained thermal model can be used to analyse the thermal behaviour of power semiconductors in steady-state conditions, at different values of the firing angle, direct current, air speed in the case of forced cooling, and different types of load. Also, the junction and case temperature of a power thyristor have been computed. In order to validate the proposed mathematical model, some experimental tests have been performed. The theoretical values are in good concordance with the experimental data and simulated results.

Diesel engines are widely used in marine transportation as a direct connection to the propeller and as electrical principal or auxiliary generator sets. The engine is the most critical piece of equipment on a vessel platform; therefore, the engine’s reliability is paramount in order to optimize safety, life cycle costs, and energy of the boat, and hence, vessel availability. In this paper, the improvements of a failure database used for a four-stroke high-speed marine diesel engine are discussed. This type of engine is normally used in military and civil vessels as the main engine of small patrols and yachts and as an auxiliary generator set (GENSET) for larger vessels. This database was assembled by considering “failure modes, effects, and criticality analysis (FMECA),” as well as an analysis of the symptoms obtained in an engine failure simulator. The FMECA was performed following the methodology of reliability-centered maintenance (RCM), while the engine response against failures wa... [more]

Inverter-fed induction motors (IMs) contain a serious of current harmonics, which become severer under stator and rotor faults. The resultant fault components in the currents affect the monitoring of the motor status. With this background, the fault components in the electromagnetic torque under stator faults considering harmonics are derived in this paper, and the fault components in current harmonics under rotor faults are analyzed. More importantly, the monitoring based on the fault characteristics (both in the torque and current) is proposed to provide reliable stator and rotor fault diagnosis. Specifically, the fault components induced by stator faults in the electromagnetic torque are discussed in this paper, and then, fault components are characterized in the torque spectrum to identify stator faults. To achieve so, a full-order flux observer is adopted to calculate the torque. On the other hand, under rotor faults, the sidebands caused by time and space harmonics in the current... [more]

This work aims to study the influence of an oxidant agent on syngas quality. A series of tests using air and steam as oxidant agents have been performed and the results compared with those of a pyrolysis test used as a reference. Tests were carried out at Sapienza University of Rome, using an updraft reactor. The reactor was fed with hazelnut shells, waste biomass commonly available in some parts of Italy. Temperature distribution, syngas composition and heating value, and producible energy were measured. Air and steam gasification tests produced about the same amount of syngas flow, but with a different quality. The energy flow in air gasification had the smallest measurement during the experiments. On the contrary, steam gasification produced a syngas flow with higher quality (13.1 MJ/Nm3), leading to the best values of energy flow (about 5.4 MJ/s vs. 3.3 MJ/s in the case of air gasification). From the cold gas efficiency point of view, steam gasification is still the best solution,... [more]

In this paper, photovoltaic (PV) string failure analysis and health monitoring of PV modules based on a low-cost self-powered wireless sensor network (WSN) are presented. Simple and effective fault detection and diagnosis method based on the real-time operating voltage of PV modules is proposed. The proposed method is verified using the developed health monitoring system which is installed in a grid-connected PV system. Each of the PV modules is monitored via WSN to detect any individual faulty module. The analysis of PV string failure includes several electrical fault scenarios and their impact on the PV string characteristics. The results show that a degraded or faulty module exhibits low operating voltage as compared to the normal module. The developed health monitoring system also includes a graphical user interface (GUI) program which graphically displays the real-time operating voltage of each module with colors and thus helping users to identify the faulty modules easily. The fa... [more]

Thermophysical properties of engineering fluids have proven in the past to be essential for the design of physical and chemical processing and reaction equipment in the chemical, metallurgical, and allied industries, as they influence directly the design parameters and performance of plant units in the of, for example, heat exchangers, distillation columns, phase separation, and reactors. In the energy field, the search for the optimization of existing and alternative fuels, either using neutral or ionic fluids, is an actual research and application topic, both for new applications and the sustainable development of old technologies. One of the most important drawbacks in the industrial use of thermophysical property data is the common discrepancies in available data, measured with different methods, different samples, and questionable quality assessment. Measuring accurately the thermal conductivity of fluids has been a very successful task since the late 1970s due to the efforts of s... [more]

Active use of heat accumulators in the thermal system has the potential for achieving flexibility in district heating with the power to heat (P2H) units, such as electric boilers (EB) and heat pumps. Thermal storage tanks can decouple demand and generation, enhancing accommodation of sustainable energy sources such as solar and wind. The overview of flexibility, using EB and storage, supported by investigating the nature of thermal demand in a Danish residential area, is presented in this paper. Based on the analysis, curve-fitting tools, such as neural net and similar day method, are trained to estimate the residential thermal demand. Utilizing the estimated demand and hourly market spot price of electricity, the operation of the EB is scheduled for storing and fulfilling demand and minimizing energy cost simultaneously. This demonstrates flexibility and controlling the EB integrated into a multi-energy system framework. Results show that the curve fitting tool is effectively suitable... [more]

This paper addresses the planning and deployment of wireless heterogeneous networks (WHNs) for smart metering, based on a cross-layer solution. We combine the constraints of the network layer that considers routing and flow demands at each link in the WHN, while at the same time, we account for the restrictions of the physical layer referred to the capacity of a short range technology when used in a multi-hop fashion. We propose a model based on a column generation approach to solve the capacitated multicommodity flow problem (CMCF); the model includes wireless links capacities, coverage, and cost. The work integrates the multi-hop routing of packets in a mesh network formed by smart meters and concentrators connected to a cellular network via base stations. The traffic of each link is represented in a multigraph with the occupation percentage, and we build a scalable routing tree on a georeferenced map to represent a real deployment. The results describe the behavior of the proposed m... [more]

The performance of ground-coupled heat pump systems (GCHPs) operating under significant groundwater flow can be difficult to predict due to advective heat transfer in the subsurface. This is the case of the Carignan-Salières elementary school located on the south shore of the St. Lawrence River near Montréal, Canada. The building is heated and cooled with a GCHP system including 31 boreholes subject to varying groundwater flow conditions due to the proximity of an active quarry being irregularly dewatered. A study with the objective of predicting the borehole temperatures in order to anticipate potential operational problems was conducted, which provided an opportunity to evaluate the impact of groundwater flow. For this purpose, a numerical model was calibrated using a full-scale heat injection test and then run under different scenarios for a period of twenty years. The heat exchange capacity of the GCHP system is clearly enhanced by advection when the Darcy flux changes from 6 × 10−... [more]

Activities of traditional longwall mining will result in ground subsidence and therefore cause issues such as damages to buildings and farmlands, water pollution and loss, and potential ecological and environmental problems in the mining region. With advantages of the longwall backfill mining method, as well as the room and pillar mining method, a continuous excavation and continuous backfill (CECB) method in longwall mining is recommended to effectively control the ground subsidence. In this method, mining roadways (MRs) are initially planned in a panel, and then they are excavated and backfilled in several stages until the whole panel is mined out and backfilled. According to the geologic conditions of an underground coal mine, and the elastic foundation beam theory, a mechanical model was built to study the subsidence of the roof while using this new mining method. In addition, methods to calculate roof subsidence in various stages in CECB were also provided. The mechanical paramete... [more]

This study focuses on the dynamics of a grid-tied voltage source converter (GVSC) during electromechanical oscillations. A small-signal model with GVSC port variables (DC voltage and AC power) as the outputs and a terminal voltage vector as the input is derived to reveal the passive response of the GVSC on the basis of the power equation in the d−q coordinate system. An input−output transfer function matrix is constructed according to the proposed model. The frequency response of this matrix in the electromechanical bandwidth is described to reflect the dynamic behavior of the GVSC. The effects of the operation parameters, i.e., the grid strength, reference value of the control system, and grid voltage, on the dynamic behavior of the GVSC in the electromechanical bandwidth, are investigated using frequency domain sensitivity. Analysis results show that the GVSC generates responses with respect to the electromechanical mode. These responses have different sensitivities to the operation... [more]

In stability studies, the response of a system enforced by external, known or unknown, inputs is of great importance. Although such an analysis is quite easy for linear systems, it becomes a cumbersome task when nonlinearities exist in the system model. Nevertheless, most of the real-world systems are externally enforced nonlinear systems with nonzero equilibriums. Representative examples in this category include power systems, where studies on stability and convergence to equilibrium constitute crucial objectives. Driven by this need, the aim of the present work is twofold: First, to substantially complete the theoretical infrastructure by establishing globally valid sufficient conditions for externally enforced nonlinear systems that converge to nonzero equilibriums and, second, to deploy an efficient method easily applicable on practical problems as it is analyzed in detail on a typical power system example. To that end, in the theoretical first part of the paper, a rigorous nonline... [more]

In line with Mexico’s interest in determining its wind resources, in this paper, 141 locations along the states of the Gulf of Mexico have been analyzed by calculating the main wind characteristics, such as the Weibull shape (c) and scale (k) parameters, and wind power density (WPD), by using re-analysis MERRA-2 (Modern-Era Retrospective Analysis for Research and Applications version 2) data with hourly records from 1980−2017 at a 50-m height. The analysis has been carried out using the R free software, whose its principal function is for statistical computing and graphics, to characterize the wind speed and determine its annual and seasonal (spring, summer, autumn, and winter) behavior for each state. As a result, the analysis determined two different wind seasons along the Gulf of Mexico;, it was found that in the states of Tamaulipas, Veracruz, and Tabasco wind season took place during autumn, winter, and spring, while for the states of Campeche and Yucatan, the only two states that... [more]

Kinematic rotary control is here proposed conceptually to enhance energy harvesting from Transverse Galloping. The effect of actively orientating the galloping body with respect to the incident flow, by imposing externally a rotation of the body proportional to the motion-induced angle of attack, is studied. To this end, a theoretical model is developed and analyzed, and numerical computations employing the Lattice Boltzmann Method are carried out. Good agreement is found between theoretical model predictions and numerical simulations results. It is found that it is possible to increase significantly the efficiency of energy harvesting with respect to the case without active rotation, which opens the path to consider this idea in practical realizations.

To reduce the dependence on oil and environmental pollution, the development of electric vehicles has been accelerated in many countries. The implementation of EVs, especially battery electric vehicles, is considered a solution to the energy crisis and environmental issues. This paper provides a comprehensive review of the technical development of EVs and emerging technologies for their future application. Key technologies regarding batteries, charging technology, electric motors and control, and charging infrastructure of EVs are summarized. This paper also highlights the technical challenges and emerging technologies for the improvement of efficiency, reliability, and safety of EVs in the coming stages as another contribution.

Biochemical methane potential tests and lab-scale continuous experiments were conducted to improve the yield and energy efficiency of anaerobic digestion through thermal hydrolysis pre-treatment. Methane generation, yield, and solubilization efficiency were evaluated through lab-scale tests. The pre-treated samples presented 50% biodegradability at 140 °C and 61.5% biodegradability at 165 °C. The increase in biodegradability was insignificant at 165 °C or higher temperature, and it was confirmed that the optimum conditions were achieved at 165 °C and 20 min of solubilization. The lab-scale continuous experiments confirmed that polymers were decomposed into low-molecular-weight compounds due to thermal hydrolysis, and pH decreased. NH4HCO3 produced by thermal hydrolysis acted as an alkali to enable a more stable operation compared to that before thermal hydrolysis. Total chemical oxygen demand as chromium (TCODCr) and soluble chemical oxygen demand as chromium (SCODCr) indicated 35.4% a... [more]

The main characteristics of the photovoltaic (PV) output power are the randomness and uncertainty, such features make it not easy to establish an accurate forecasting method. The accurate short-term forecasting of PV output power has great significance for the stability, safe operation and economic dispatch of the power grid. The deterministic point forecast method ignores the randomness and volatility of PV output power. Aiming at overcoming those defects, this paper proposes a novel hybrid model for short-term PV output power interval forecasting based on ensemble empirical mode decomposition (EEMD) as well as relevance vector machine (RVM). Firstly, the EEMD is used to decompose the PV output power sequences into several intrinsic mode functions (IMFs) and residual (RES) components. After that, based on the decomposed components, the sample entropy (SE) algorithm is utilized to reconstruct those components where three new components with typical characteristics are obtained. Then, b... [more]

This study is mainly to provide an overview of human walking induced energy harvest. Focusing on the proportion of all energy sources provided by daily activity, the available human walking induced energy is divided with respect to the generation principle. The extensive research on harvesting energy results from body vibration, inertial element, and foot press to convert into electricity is overviewed. Over the past decades, various smart materials have been employed to achieve energy conversion. Generators based on electromagnetic induction or the triboelectric effect were developed and integrated. Small captured power and low overall efficiency are criticized. The concept of human walking energy harvest is extended into the wearable walking robotics using other mediums, such as fluid, to transmit power instead of electricity. By comparison, it is indicated that less energy conversion links are involved in energy regeneration of such applications and expected to guarantee less loss a... [more]

The electrical efficiency and durability of a photovoltaic (PV) cell degrades as its temperature increases. Accordingly, there have been continued efforts to control the cell temperature by cooling the PV module. Generally, passive PV cooling using heat sinks attached on the back of the PV module can improve the electrical efficiency. However, few experimental studies have evaluated the effect of the heat sink shape on PV cooling. Therefore, this study proposed a passive cooling technology using meshes made of iron and aluminum, and performed indoor tests using a solar simulator to analyze the cooling performance. The experimental results demonstrated that iron and aluminum meshes reduced the PV module temperature by approximately 4.35 °C and 6.56 °C, respectively. Additionally, numerical studies were performed using a computational fluid dynamics (CFD) simulation to compare the cooling fins and meshes. The numerical results showed that the cooling fins exhibited a better cooling perfo... [more]

Considering that the world transport sector is the second largest contributor of global greenhouse gas (GHG) emissions due to energy use and the least decarbonized sector, it is highly recommended that all countries implement ambitious public policies to decarbonize this sector. In Mexico the transport sector generates the largest share of greenhouse gas emissions, in 2014 it contributed with 31.3% of net emissions. Two original scenarios for the Mexican transport sector, a no-policy baseline scenario (BLS) and a low carbon scenario (LCS) were constructed. In the LCS were applied 21 GHG mitigation measures, which far exceeds the proposals for reducing transport sector GHG emissions that Mexico submitted in its National Determined Contributions (NDC). As a result, the proposed LCS describes a sector transformation path characterized by structural changes in freight and passenger mobility, new motor technologies for mobility, introduction of biofuels, price signals, transportation practi... [more]

Details about a fault’s progression, including the remaining-useful-lifetime (RUL), are key features in monitoring, industrial operation and maintenance (O&M) planning. In order to avoid increases in O&M costs through subjective human involvement and over-conservative control strategies, this work presents models to estimate the RUL for wind turbine main bearing failures. The prediction of the RUL is estimated from a likelihood function based on concepts from prognostics and health management, and survival analysis. The RUL is estimated by training the model on run-to-failure wind turbines, extracting a parametrization of a probability density function. In order to ensure analytical moments, a Weibull distribution is assumed. Alongside the RUL model, the fault’s progression is abstracted as discrete states following the bearing stages from damage detection, through overtemperature warnings, to over overtemperature alarms and failure, and are integrated in a separate assessment model. A... [more]

The purpose of this study is to determine the issues that financial institutions should pay attention to in their decision to provide financing to large scale energy projects. Within this framework, taking into account the Balanced Scorecard (BSC) approach, 4 dimensions and 8 criteria that can be effective in these decisions of financial institutions were determined. After that, the importance weights of these dimensions and criteria were determined by interval type-2 (IT2) fuzzy DEMATEL method. In addition, 3 different types of banks (public, private, foreign) are listed for their performance in financing energy projects. According to the results of the analysis, the technological and financial adequacy of the company that will invest in energy is the issue that financial institutions should pay the most attention to in their credit decision. Therefore, it is important for financial institutions to visit the customer's location and pay attention to the technological adequacy in the pr... [more]

Improving the energy efficiency of buildings is among the most urgent social development tasks due to the scale of energy consumption in this industry. At the same time, it is essential to meet high requirements for indoor environmental quality and thermal comfort. The issue of overheating is most often analysed in summer but it also occurs in transition seasons, when the cooling systems do not operate. The paper attempts to evaluate the effectiveness of external mobile shading elements on the microclimate of rooms with large glazed areas in the transition season. Passive solutions, such as shading elements, which limit the increase of indoor temperature, do not always allow the acquisition and maintenance of comfortable solutions for the duration of the season, as demonstrated by the authors. Temporary cooling of the rooms may be necessary to maintain comfortable conditions for the users, or other solutions should be devised to improve comfort (e.g., reduction of clothing insulation c... [more]

Pyrolysis of anaerobically digested sludge can serve as an efficient biomass for biofuel production. Pyrolysis produces products like char, bio-oil, and combustible gases by thermochemical conversion process. It can be used for sludge treatment that decreases sludge disposal problems. Sludge produced from anaerobic co-digestion (microalgae, cow dung, and paper) waste has high carbon and hydrogen content. We investigated the candidacy of the anaerobic sludge having high heating value (HHV) of 20.53 MJ/kg as a reliable biomass for biofuels production. The process of pyrolysis was optimized with different temperatures (400, 500, and 600 °C) to produce high quantity and improved quality of the products, mainly bio-oil, char, and gas. The results revealed that with the increase in pyrolysis temperature the quantity of char decreased (81% to 55%), bio-oil increased (3% to 7%), and gas increased (2% to 5%). The HHV of char (19.2 MJ/kg), bio-oil (28.1 MJ/kg), and gas (18.1 MJ/kg) were predomin... [more]

The aim of this study is to assess how the use of fossil and nuclear power in different renovation scenarios affects the environmental impacts of a multi-family dwelling in Sweden, and how changes in the electricity production with different energy carriers affect the environmental impact. In line with the Paris Agreement, the European Union has set an agenda to reduce greenhouse gas emissions by means of energy efficiency in buildings. It is estimated that by the year 2050, 80% of Europe’s population will be living in buildings that already exist. This means it is important for the European Union to renovate buildings to improve energy efficiency. In this study, eight renovation scenarios, using six different Northern European electricity mixes, were analyzed using the standard of the European Committee for Standardization for life cycle assessment of buildings. This study covers all life cycle steps from cradle to grave. The renovation scenarios include combinations of photovoltaics,... [more]