The smart grid employs computing and communication technologies to embed intelligence into the power grid and, consequently, make the grid more efficient. Machine learning (ML) has been applied for tasks that are important for smart grid operation including energy consumption and generation forecasting, anomaly detection, and state estimation. These ML solutions commonly require sufficient historical data; however, this data is often not readily available because of reasons such as data collection costs and concerns regarding security and privacy. This paper introduces a recurrent generative adversarial network (R-GAN) for generating realistic energy consumption data by learning from real data. Generativea adversarial networks (GANs) have been mostly used for image tasks (e.g., image generation, super-resolution), but here they are used with time series data. Convolutional neural networks (CNNs) from image GANs are replaced with recurrent neural networks (RNNs) because of RNN’s ability... [more]

In this paper, we test the use of Markov-switching (MS) GARCH (MSGARCH) models for trading either oil or natural gas futures. Using weekly data from 7 January 1994 to 31 May 2019, we tested the next trading rule: to invest in the simulated commodity if the investor expects to be in the low-volatility regime at t + 1 or to otherwise hold the risk-free asset. Assumptions for our simulations included the following: (1) we assumed that the investors trade in a homogeneous (Gaussian or t-Student) two regime context and (2) the investor used a time-fixed, ARCH, or GARCH variance in each regime. Our results suggest that the use of the MS Gaussian model, with time-fixed variance, leads to the best performance in the oil market. For the case of natural gas, we found no benefit of using our trading rule against a buy-and-hold strategy in the three-month U.S. Treasury bills.

Biomass materials have been increasingly used due to their renewable nature. The problems occurring during the storage of fresh woody materials include gas emissions and dry matter losses as a result of degradation. The objective of this study was to investigate and quantify the effect of moisture content on gas emissions from stored wood chips. Experiments were conducted under non-aerobic and aerobic conditions using fresh Western Red Cedar (WRC) chips with different initial moisture contents over a range of temperatures. The peak CO2 emission factor of 2.9 g/kg dry matter (DM) was observed from high moisture chips at 20 °C under non-aerobic conditions after two-month storage, which was an order of magnitude greater than that from low moisture chips. In the case of volatile organic compounds, a range of compounds were detected from all tests. The concentration of VOCs was found to be positively correlated with moisture content. Gas emissions from the aerobic reactors exhibited similar... [more]

In Japan, residents of apartments are generally contracted to receive low voltage electricity from electric utilities. In recent years, there has been an increasing number of high voltage batch power receiving contracts for condominiums. In this research, a high voltage batch receiving contractor introduces a demand−response in a low voltage power receiving contract, which maximizes the profit of a high voltage batch receiving contractor and minimizes the electricity charge of residents by utilizing battery storage, electric vehicles (EV), and heat pumps. A multi-objective optimization algorithm calculates a Pareto solution for the relationship between two objective trade-offs in the MATLAB ® environment.

To investigate a typical large-scale nonlinear hydropower system (HS) with a stochastic water flow, a novel nonlinear adaptive control scheme, which is created by the combination of a backstepping strategy, nonsingular fast terminal sliding mode surface and command filter, is proposed for the hydro-turbine governor design of a HS to not only improve the transient stability of the HS but also increase the energy conversion efficiency and improve the reliability and availability of the electricity supply. In contrast to previous research based on ideal hydro-turbine models with accurate parameters, an adaptive backstepping nonsingular fast terminal sliding mode control (ABNFTSMC) with command filtered (CF) is proposed in which virtual control inputs and error compensations are applied to overcome distribution characteristics resulting from energy losses, while guaranteeing finite-time convergence. In addition, to avoid the requirement of analytic differentiation in Lyapunov stability, a... [more]

The co-evolution of techno-economic, societal, environmental and political-institutional systems towards sustainable energy transitions is largely influencing the disruptive reconfiguration of the energy sector across the globe. At the heart of this disruption is the peer-to-peer energy sharing concept. Nonetheless, peer-to-peer energy sharing business models are yet very little put into practice due to the rigid energy market structures and lagging regulatory frameworks across the globe. In view of this, this paper presents a novel peer-to-peer energy sharing business model developed specifically for the context of the Portuguese energy market, which was successfully trialed in three pilot projects in Portugal under real market conditions. All things considered, the novelty of this paper lies on an innovative approach for the collaborative use of the surplus electricity generation from photovoltaic systems between end-users under the same low voltage/medium voltage transformer substat... [more]

Residential microgrid is widely considered as a new paradigm of the home energy management system. The complexity of Microgrid Energy Scheduling (MES) is increasing with the integration of Electric Vehicles (EVs) and Renewable Generations (RGs). Moreover, it is challenging to determine optimal scheduling strategies to guarantee the efficiency of the microgrid market and to balance all market participants’ benefits. In this paper, a Multi-Agent Reinforcement Learning (MARL) approach for residential MES is proposed to promote the autonomy and fairness of microgrid market operation. First, a multi-agent based residential microgrid model including Vehicle-to-Grid (V2G) and RGs is constructed and an auction-based microgrid market is built. Then, distinguish from Single-Agent Reinforcement Learning (SARL), MARL can achieve distributed autonomous learning for each agent and realize the equilibrium of all agents’ benefits, therefore, we formulate an equilibrium-based MARL framework according t... [more]

Dilation behavior is of great importance for reasonable modeling of the stability of the host rock of the repository for high-level radioactive waste disposal. It is a suitable method for carrying out direct shear experiments to analyze the dilation behavior of rock with well understood physical meanings. Based on a series of direct shear experiments on granite samples from the Alxa candidate area under different normal stresses, the shear stress‒shear strain and shear stress‒normal strain relations have been studied in detail. Five typical stages have been divided associated with the fracturing process and deformation behaviors of the granite samples during the experimental process, and the method to determine the typical stress thresholds has been proposed. It has also been found that the increasing normal stress may reduce the maximum dilation angle, and when the normal stress is relatively lower, the negative dilation angle may occur during the post-peak stage. According to the dat... [more]

With the increasing environmental concerns, plug-in electric vehicles will eventually become the main transportation tools in future smart cities. As a key component and the main power source, lithium-ion batteries have been an important object of research studies. In order to efficiently control electric vehicle powertrains, the state of charge (SOC) of lithium-ion batteries must be accurately estimated by the battery management system. This paper aims to provide a more accurate dynamic SOC estimation method for lithium-ion batteries. A dynamic Thevenin model with variable parameters affected by the temperature and SOC is established to model the battery. An unscented Kalman particle filter (UPF) algorithm is proposed based on the unscented Kalman filter (UKF) algorithm and the particle filter (PF) algorithm to generate nonlinear particle filter according to the advantages and disadvantages of various commonly used filtering algorithms. The simulation results show that the unscented K... [more]

Background: This paper proposes a Nautilus isometric spiral vertical axis wind turbine, which is a new structure, and its aerodynamic performance and power generation performance need to be analyzed. Methods: A 3D model of the wind turbine was built and its aerodynamic performance was analyzed. Then the wind turbine power generation and grid-connected simulation platform was built by MATLAB/SIMULINK, and its power generation performance and subsequent grid connection were studied. Results: The basic parameters of the wind turbine were obtained. In order to improve efficiency, parameters such as pressure, torque, wind energy utilization rate and relative velocity of wind turbines with different blade numbers and different sizes were compared. In addition, by building a simulation platform for the power generation control system, the power generation characteristics and grid connection characteristic curves of the generator were obtained. Conclusions: When the number of blades is three a... [more]

This study presents a methodology for classifying road traffic energy efficiency. The indicators defined discriminate the impact of the road vertical and horizontal alignments upon energy consumption, disclosing the improvement potential of the road as a function of the traffic origin−destination matrix. The methodologic approach is based on basic physical principals, thus guarantying its generality, as opposed to the usual empirical mesoscale approaches. A simplified algebraic procedure is also proposed, resorting to simplified driving cycles and a constant speed assumption (CSA), thus avoiding the intricacy of microscale/microsimulation models. The simplified methodology was validated against field data acquired on the Portuguese highway A25. A microscale vehicle specific power analysis combined with detailed fuel models is compared against CSA results. The findings demonstrate its adequacy for free-flow traffic conditions and the importance of classifying road traffic energy-efficie... [more]

The 2018 recast of the Renewable Energy Directive (RED II) defines “renewable energy communities” (RECs), introducing a new governance model and the possibility of energy sharing for them. It has to be transposed into national law by all European Union Member States until June 2021. This article introduces consumer stock ownership plans (CSOPs) as the prototype business model for RECs. Based on the analysis of a dataset of 67 best-practice cases of consumer (co-) ownership from 18 countries it demonstrates the importance of flexibility of business models to include heterogeneous co-investors for meeting the requirements of the RED II and that of RE clusters. It is shown that CSOPs—designed to facilitate scalable investments in utilities—facilitate co-investments by municipalities, SMEs, plant engineers or energy suppliers. A low-threshold financing method, they enable individuals, in particular low-income households, to invest in renewable projects. Employing one bank loan instead of m... [more]

Space conditioning is responsible for the majority of carbon dioxide emission and fossil fuel consumption during a building’s life cycle. The exploitation of renewable energy sources, together with efficiency enhancement, is the most promising solution. An innovative layout for ground-source heat pumps, featuring upstream thermal energy storage (uTES), was already proposed and proved to be as effective as conventional systems while requiring lower impact geothermal installations thanks to its ability to decouple ground and heat-pump energy fluxes. This work presents further improvements to the layout, obtained using more compact and efficient thermal energy storage containing phase-change materials (PCMs). The switch from sensible- to latent-heat storage has the twofold benefit of dramatically reducing the volume of storage (by a factor of approximately 10) and increasing the coefficient of performance of the heat pump. During the daily cycle, the PCMs are continuously melted/solidifie... [more]

In this study, a millimeter-wave (MMW) radar and an onboard camera are used to develop a sensor fusion algorithm for a forward collision warning system. This study proposed integrating an MMW radar and camera to compensate for the deficiencies caused by relying on a single sensor and to improve frontal object detection rates. Density-based spatial clustering of applications with noise and particle filter algorithms are used in the radar-based object detection system to remove non-object noise and track the target object. Meanwhile, the two-stage vision recognition system can detect and recognize the objects in front of a vehicle. The detected objects include pedestrians, motorcycles, and cars. The spatial alignment uses a radial basis function neural network to learn the conversion relationship between the distance information of the MMW radar and the coordinate information in the image. Then a neural network is utilized for object matching. The sensor with a higher confidence index is... [more]

Ocean wave energy is one of the cleanest renewable energy sources around the globe, but wave energy varies widely from place to place and from time to time. The long-term variability of wave power at 20 locations in the Indian shelf seas from 1979 to 2018 is described here using the European Centre for Medium-Range Weather Forecasts recently released ERA5 reanalysis hourly data. The variability is calculated on a yearly and monthly basis for the locations based on the coefficient of variation. The annual average wave power varied from 2.3 (at location 16 in the western Bay of Bengal) to 11 kW/m (at location 2 in the northeastern Arabian Sea). Along the western shelf seas, the maximum value of wave power is during the southwest monsoon period and along the east coast, it is during the tropical cyclone period. The standard deviation in wave power is more than the mean value at locations along the northern shelf seas of India, indicating a large variability in wave power in an annual cycl... [more]

A hollow electric heating cylinder is inserted inside a thermo-insulating cylindrical body of larger diameter, together representing a single cylindrical heating element. Three cylindrical heating elements, with an independent electrical source, are arranged alternately one after the other to form a heating duct. The internal diameters of the hollow heating cylinders are different, and the cylinders are arranged from the largest to the smallest in the nanofluid’s flow direction. Through these hollow heating cylinders passes nanofluid, which is thereby heated. The material of the hollow heating cylinders is a PTC (positive temperature coefficient) heating source, which allows maintaining approximately constant temperatures of the cylinders’ surfaces. The analytical analysis used three temperatures of the hollow heating cylinders of 400 K, 500 K, and 600 K. The temperatures of the heating cylinders are varied for each of the three cylindrical heating elements. In the same arrangement, th... [more]

The oxygen compressor is one of the key components in the onboard oxygen generating system (OBOGS), with a high-pressure canister for backup. In this paper, a multistage compressor unit with a non-crank mechanism is proposed for the compression of the generated oxygen for storage in the high-pressure canister in the oxygen backup line of the OBOGS. The working principle, control strategy, and the design method of the key components of the non-crank compressor are provided to realize the preliminary design. The experimental study was carried out to investigate the control accuracy and the technical feasibility, including the compression capacity and the cooling performance. Results show that the motion control program could realize the motion scheme of the compressor with an error of less than 2%. The discharge pressure reached a relative stability after around 40 cycles of compression, while the discharge temperature achieved relative stability after approximately 100 cycles. The avera... [more]

Increasing the share of renewables in energy markets influences the daily operation of thermal power units. High capacity power units are more frequently operated to balance power grids and, thus, steam boilers are exposed to unfavorable transient states. The aim of this work was to perform thermal and structural analyses of a boiler’s outlet steam header, with a capacity of 650∙103 kg/h (180 kg/s) of live steam. Based on the measured steam pressure and temperatures on the outer surface of the component, transient temperature fields were determined by means of an algorithm that allows determination of transient stress distributions on the internal and external surfaces, as well as at stress concentration regions. In parallel, a finite element method simulation was performed. A comparison of the obtained results to a finite element analysis showed satisfactory agreement. The analyses showed that the start-up time could be reduced because the total stress did not exceed the allowed value... [more]

We formulated a problem faced by a power producer who owns a combined-cycle gas turbine (CCGT) and desires to maximize its expected profit in a medium-term planning horizon. We assumed that this producer can participate in the spot and over-the-counter markets to buy and sell natural gas and electricity. We also considered that the power producer has gas storage available that can be used for handling the availability of gas and the uncertainty of gas prices. A stochastic programming model was used to formulate this problem, where the electricity and gas prices were characterized as stochastic processes using a set of scenarios. The proposed model includes the technical constraints resulting from the operation of the combined cycle power plant and the gas storage and a detailed description of the different markets in which the power producer can participate. Finally, the performance of the proposed model is tested in a realistic case study. The numerical results show that the usage of... [more]

Passive safety systems are an important feature of currently designed and constructed nuclear power plants. They operate independent of external power supply and manual interventions and are solely driven by thermal gradients and gravitational force. This brings up new needs for performance and reliably assessment. This paper provides a review on fundamental approaches to model and analyze the performance of passive heat removal systems exemplified for the passive heat removal chain of the KERENA boiling water reactor concept developed by Framatome. We discuss modeling concepts for one-dimensional system codes such as ATHLET, RELAP and TRACE and furthermore for computational fluid dynamics codes. Part I dealt with numerical and experimental methods for modeling of condensation inside the emergency condenser and on the containment cooling condenser. This second part deals with boiling and two-phase flow instabilities.

As the importance of the levelized cost of electricity (LCOE) increases in the solar cell industry, the demand for high-efficiency solar cells is rapidly increasing. Typically, p-type passivated emitter rear contact (PERC) solar cells are the most commonly used in the industry, and their efficiency is approximately 22−23%. P-type solar cells are reported to exhibit a light-induced degradation (LID) phenomenon, in which their output constantly decreases during power generation under solar radiation, and the output significantly reduces as their reference efficiency increases. Ultra-high-efficiency solar cells, which are on high demand, have a considerable output reduction due to the LID phenomenon; hence, technologies to prevent the LID phenomenon are required. However, research on this phenomenon has not been conducted because there is no method to transfer heat to solar cells inside the encapsulant when the modules are produced. In this study, a regeneration state was formed by remote... [more]

In order to better release the heat generated by the electronic components, a novel heat dissipation system is proposed, which combines a microchannel heat pipe (MHP) with a high thermal conductivity and a radiative plate with a high emissivity at nighttime. First, a simple testing rig was made with an MHP and a radiative plate, where the radiative plate was made of acrylic resin, a curing agent, thinner, and aluminum plate, and had strong radiative cooling at nighttime. Second, the mathematical model was initially established and verified using experiments, where it was shown that the agreement between numerical and experimental data was well within experimental uncertainties. Comprehensive simulation investigations were conducted by varying wind speed, relative humidity, the cloudiness coefficient, dimension of the radiative plate, and tilted angle. The results show that: (1) the emissivity of the radiative plate was about 0.311 in the daytime and about 0.908 in the nighttime; (2) th... [more]

The energy planning process essentially requires addressing diverse planning objectives, including prioritizing resources, and the estimation of environmental emissions and associated health risks. This study investigates the impacts of atmospheric pollution for Pakistan from the energy production processes under various modalities. A national-scale bottom-up energy optimization model (Pak-TIMES) with the ANSWER-TIMES framework is developed to assess the electricity generation pathways (2015−2035) and estimate GHG emissions and major air pollutants, i.e., CH4, CO, CO2, N2O, NOX, PM1, PM10, PM2.5, PMBC, PMOC, PMTSP, SO2, and VOC under five scenarios. These scenarios are: BAU (business-as-usual), RE-30 (30% renewables), RE-40 (40% renewables), Coal-30 (30% coal), and Coal-40 (40% coal). It is revealed that to reach the electricity demand of 3091 PJ in 2035, both the Coal-30 and Coal-40 scenarios shall cause maximum emissions of GHGs, i.e., 260.13 and 338.92 Mt (million tons) alongside 40... [more]

Non-Orthogonal Multiple Access (NOMA) has been proposed recently as an emerging radio access technology for the Fifth Generation (5G) to achieve high spectral efficiency (SE). In addition, simultaneous wireless information and power transfer (SWIPT) has been receiving exceptional attention because of its role in increasing energy efficiency (EE). In this paper, the performance of the downlink SWIPT-NOMA system has been evaluated. In this paper, signal to interference and noise ratio (SINR) is derived for near and far users with outage probability for each user, where the near user acts as an energy harvesting (EH) node. The Genetic algorithm (GA) is used as an optimization technique for the power splitting ratio and power allocation coefficients to maximize the EE under eligible SE. The outage probability for the near and far user is taken into consideration for the optimization process. In this work, the results from the SE−EE metric show that the maximum EE reached 0.325 Mbits/J at S... [more]

The measurement procedures for frequency response analysis (FRA) of power transformers are well documented in IEC and IEEE standards. However, the interpretation of FRA results is still far from reaching an accepted methodology and is limited to the analysis of the experts. The dilemma is that there are limited case studies available to understand the effect of different faults. Additionally, due to the destructive nature, it is not possible to apply the real mechanical deformations in the transformer windings to obtain the data. To solve these issues, in this contribution, the physical geometry of a three-phase transformer is simulated using 3D finite integration analysis to emulate the real transformer operation. The novelty of this model is that FRA traces are directly obtained from the 3D model of windings without estimating and solving lumped parameter circuit models. At first, the method is validated with a simple experimental setup. Afterwards, different mechanical and electrica... [more]