In this paper, a vehicle−grid integration (VGI) control strategy for radial power distribution networks is presented. The control schemes are designed at both microgrid level and distribution level. At the VGI microgrid level, the available power capacity for electric vehicle (EV) charging is optimally allocated for charging electric vehicles to meet charging requirements. At the distribution grid level, a distributed voltage compensation algorithm is designed to recover voltage violation when it happens at a distribution node. The voltage compensation is achieved through a negotiation between the grid-level agent and VGI microgrid agents using the alternating direction method of multipliers. In each negotiation round, individual agents pursue their own objectives. The computation can be carried out in parallel for each agent. The presented VGI control schemes are simulated and verified in a modified IEEE 37 bus distribution system. The simulation results are presented to show the effe... [more]

The results of a techno-economic model of distributed wind-hydrogen systems (WHS) located at each existing wind farm on the island of Ireland are presented in this paper. Hydrogen is produced by water electrolysis from wind energy and backed up by grid electricity, compressed before temporarily stored, then transported to the nearest injection location on the natural gas network. The model employs a novel correlation-based approach to select an optimum electrolyser capacity that generates a minimum levelised cost of hydrogen production (LCOH) for each WHS. Three scenarios of electrolyser operation are studied: (1) curtailed wind, (2) available wind, and (3) full capacity operations. Additionally, two sets of input parameters are used: (1) current and (2) future techno-economic parameters. Additionally, two electricity prices are considered: (1) low and (2) high prices. A closest facility algorithm in a geographic information system (GIS) package identifies the shortest routes from each... [more]

Solution mining for glauberite salt rock is a long-term process that takes several years to several decades. Therefore, deposit deformations and subsidence of ground surfaces are time-dependent deformation problems that should consider the effect of water dissolution. In order to investigate the time-dependent deformation characteristics of glauberite salt rock, tri-axial time-dependent deformation tests were conducted under the condition of 4 MPa confining pressure and 5 MPa axial pressure with infiltration pressures of 3, 2, 1, and 0 MPa, respectively, and the micro-CT scan system was used to scan the glauberite specimens before and after the experiment in order to study the fracture evolution inside the specimen, and a damage constitutive model was established to fit the time-dependent deformation curves based on the damage mechanics and effective stress principle. To simulate the solution mining process, the time-dependent deformation process of glauberite salt rock was divided int... [more]

This article presents a simulation study which focuses on the thermodynamic analysis of a solar-driven trigeneration system for heating, cooling, and electricity production. The system uses parabolic trough collectors operating with Therminol VP-1 for feeding an organic Rankine cycle operating with toluene and an absorption heat pump operating with a LiBr−H2O working pair. The collecting area is selected at 100 m2 and the storage tank at 4 m3. The system is studied parametrically in order to examine the impact of various parameters on the system energy efficiency, system exergy efficiency, electricity production, heating production, and cooling production in the simple payback period of the investment. The examined parameters are the following: solar beam irradiation level, solar beam irradiation angle, superheating degree in the turbine inlet, pressure level in the turbine inlet, heat source temperature level, generator temperature level, and the heat input in the generator. For the n... [more]

Bioenergy is one of the alternatives to secure energy demand, despite increasing debate on the sustainability of using bioenergy as a renewable source. As the source is disseminated over a large area and affected by seasonality, the potential benefit is highly dependent on other cost and benefit trade-offs along the supply chain. This review paper aims to assess operational management research methods used in biofuel supply chain planning, including both upstream production and international downstream trading. There have been considerable operational management studies done on upstream processes in biofuel production based on different strategic and tactical decision making of a single or multiple feedstocks, considering economic and environmental factor. However, the environmental consideration is often limited to carbon emission where the other environmental impact such as land-use change, biodiversity loss, irrigation and fertilisation are often being overlooked. Biofuel supply cha... [more]

This Special Issue collects innovative contributions in the field of wind turbine optimization technology. The general motivation of the present Special Issue is given by the fact that there has recently been a considerable boost of the quest for wind turbine efficiency optimization in the academia and in the wind energy practitioners communities. The optimization can be focused on technology and operation of single turbine or a group of machines within a wind farm. This perspective is evidently multi-faced and the seven papers composing this Special Issue provide a representative picture of the most ground-breaking state of the art about the subject. Wind turbine power optimization means scientific research about the design of innovative aerodynamic solutions for wind turbine blades and of wind turbine single or collective control, especially for increasing rotor size and exploitation in offshore environment. It should be noticed that some recently developed aerodynamic and control so... [more]

A new test rig has been designed, built and commissioned, and is now jointly pursued to facilitate experimental investigations into advanced combustion processes (i.e., dual fuel, multi-mode) under turbulent conditions at high, engine-like temperature and pressure levels. Based on a standard diesel engine block, it offers much improved optical access to the in-cylinder processes due to its separated and rotated arrangement of the compression volume and combustion chamber, respectively. A fully variable pneumatic valve train and the appropriate preconditioning of the intake air allows it to represent a wide range of engine-like in-cylinder conditions regarding pressures, temperatures and turbulence levels. The modular design of the test rig facilitates easy optimizations of the combustion chamber/cylinder head design regarding different experimental requirements. The name of the new test rig, Flex-OeCoS, denotes its Flexibility regarding Optical engine Combustion diagnostics and/or the... [more]

Blockchain technology is increasingly used worldwide to enhance the performance and profit of any environment through its defining characteristics, such as security, auditability, immutability, and inconspicuousness. Owing to these characteristics, the blockchain can be used in various non-financial operations of some domains, such as the Internet of Things (IoT) and distributed computing. However, implementing blockchain technology in IoT is not always a feasible solution because blockchain deployment is costly, it has limited extensibility and provides irregular bandwidth and latency. In this regard, a simple size extensible (SSE) blockchain has been proposed to provide an optimal solution for IoT environments by satisfying the needs of the IoT environment as well as ensuring end-to-end security. The implementation of the proposed blockchain develops an overlay network to obtain a distributed environment where the blockchain is handled by the resources present therein. Two novel algo... [more]

This study provides a double elastic steel sheet (DESS) piezoelectric energy harvester system, in which the vibration generated by the deformation and clap of two elastic steel sheets is assisted by a piezo patch to generate electric energy. The system is combined with energy storage equipment to propose a complete solution forgreen energy integration. This study buildsexperimentallyon the model of the proposed system to explore its voltage, power output and energy collection efficiency. This study also builds atheoretical model of a nonlinear beam with the piezo patch, including the piezoelectric coupling coefficient and current equation. This nonlinear problem is analyzed by the method of multiple scales (MOMS). The system frequency response wasobserved using fixed points plots. The perturbation technique and numerical method wereused to mutually validate the experimental results; the concept of DESS vibration energy harvester (DESS VEH) is proved feasible. In order to prolong the li... [more]

Datong Basin is a Cenozoic fault basin located in the central part of the North China Block with strong tectonic activity. The unique geological environment of Datong Basin is believed to have good conditions for the formation of geothermal resources. Based on the research of the classification, genesis and geothermal geological characteristics of geothermal resources, the geological conditions, seismic activity, volcanic activity, geophysical exploration results, terrestrial heat flow and hot springs in Datong Basin are analyzed. The possibility of the occurrence of geothermal resources in Datong Basin is determined, and the genesis and occurrence mechanisms of geothermal resources in Datong Basin are judged. The results show that Datong Basin satisfies the geological geothermal conditions of the formation of geothermal resources and is of great research value. The formation of geothermal resources in the Datong Basin is affected by the uplift of the Qinghai−Tibet Plateau and the dest... [more]

An increase in demand for renewable energy resources, energy storage technologies, and electric vehicles requires high-power level DC-DC converters. The DC-DC converter that is suitable for high-power conversion applications (i.e., resonant, full-bridge or the dual-active bridge) requires magnetic transformer coupling between input and output stage. However, transformer design in these converters remains a challenging problem, with several non-linear scaling issues that need to be simultaneously optimized to reduce losses and maintain acceptable performance. In this paper, a new transformer-less high step-up boost converter with a charge pump capacitorand capacitor-inductor-diode CLD cell is proposed using dynamic modeling. The experimental and simulation results of the proposed converter are carried out in a laboratory and through Matlab Simulink, where 10 V is given as an input voltage, and at the output, 100 V achieved in the proposed converter. A comparative analysis of the propose... [more]

Diagnostic and condition monitoring of power transformers are key actions to guarantee their safe operation. The subsequent benefits include reduced service interruptions and economic losses associated with their unavailability. Conventional test methods developed for the condition assessment of power transformers have certain limitations. To overcome such problems, fiber optic-based sensors for monitoring the condition of transformers have been developed. Flawlessly built-up fiber optic-based sensors provide online and offline assessment of various parameters like temperature, moisture, partial discharges, gas analyses, vibration, winding deformation, and oil levels, which are based on different sensing principles. In this paper a variety and assessment of different fiber optic-based diagnostic techniques for monitoring power transformers are discussed. It includes significant tutorial elements as well as some analyses.

In order to provide specific references and suggestions for the design and operation of underground pumping stations, in this paper, an experimental model of an underground pumping station, including 4 pumps and 2 pump intakes (primary and secondary), was obtained through similitude of fluid mechanics. The phase diagrams of various vortices, in terms of different dimensionless numbers are presented, which can reveal their appearance and evolution process. Three specific cases with different vortex flows were analyzed. The experiment results may provide a reference for the current design guidelines for underground pumping stations.

It is widely acknowledged that strategies to decarbonize energy systems cannot omit the mobility sector. For several decades, particularly in urban areas, a shift from car-based mobility to more environmental-friendly modes has been high on political agendas. Progress has been made in many urban areas, but so far only in small, rather incremental steps. The dominance of the car has remained largely stable in urban transport. For some time now, many experts have argued that processes of digitalization will co-evolve with societal trends and lead to multimodal urban mobility regimes in which private car usage will lose its dominance. In this paper, we examine if stakeholders active in the field believe that, despite digitalization, policy interventions are essential to achieve such a transition. The analysis draws on concepts from transition research and is based on 10 semi-structured interviews with providers of innovative mobility services that may contribute to more multimodal urban m... [more]

The characteristics of the transcritical CO2 heat pump water heater (HPWH) system are; a lower inlet hot water temperature (Ti-hw) (sometimes this is lower than the water source temperature), and an outlet gas cooler temperature (To-gc) which is affected by the Ti-hw and often lower than the critical temperature. In order to study the effects of the internal heat exchanger (IHX) on the operational performance of the transcritical CO2 HPWH when To-gc is low, a transcritical CO2 water source HPWH experiment platform is established to conduct experimental research and comparative analysis on the operational performance of the transcritical CO2 water source HPWH, with or without IHX. It is found that, if only the coefficient of performance (COP) and heating at the optimal exhaust pressure of the transcritical CO2 water source HPWH were considered, COP and the heating of the non-IHX system would be slightly higher than those of the IHX system at the lower hot water flow and water source tem... [more]

Hydro power can provide a source of dispatchable low-carbon electricity and a storage solution in a climate-dependent energy mix with high shares of wind and solar production. Therefore, understanding the effect climate has on hydro power generation is critical to ensure a stable energy supply, particularly at a continental scale. Here, we introduce a framework using climate data to model hydro power generation at the country level based on a machine learning method, the random forest model, to produce a publicly accessible hydro power dataset from 1979 to present for twelve European countries. In addition to producing a consistent European hydro power generation dataset covering the past 40 years, the specific novelty of this approach is to focus on the lagged effect of climate variability on hydro power. Specifically, multiple lagged values of temperature and precipitation are used. Overall, the model shows promising results, with the correlation values ranging between 0.85 and 0.98... [more]

Accurate estimation of the state of charge (SOC) is an important criterion to prevent the batteries from being over-charged or over-discharged, and this assures an electric vehicle’s safety and reliability. To investigate the effect of different operating conditions on the SOC estimation results, a dual-polarization model (DPM) and a fractional-order model (FOM) are established in this study, taking into account the prediction accuracy and structural complexity of a battery model. Based on these two battery equivalent circuit models (ECMs), a hybrid Kalman filter (HKF) algorithm is adopted to estimate the SOC of the battery; the algorithm comprehensively utilizes the ampere-hour (Ah) integration method, the Kalman filter (KF) algorithm, and the extended Kalman filter (EKF) algorithm. The SOC estimation results of the DPM and FOM, under the dynamic stress test (DST), federal urban driving schedule (FUDS), and hybrid pulse power characteristic (HPPC) cycle conditions, are compared and an... [more]

Monitoring and diagnosis of coal mill systems are critical to the security operation of power plants. The traditional data-driven fault diagnosis methods often result in low fault recognition rate or even misjudgment due to the imbalance between fault data samples and normal data samples. In order to obtain massive fault sample data effectively, based on the analysis of primary air system, grinding mechanism and energy conversion process, a dynamic model of the coal mill system which can be used for fault simulation is established. Then, according to the mechanism of various faults, three types of faults (i.e., coal interruption, coal blockage and coal self-ignition) are simulated through the modification of model parameters. The simulation shows that the dynamic characteristic of the model is consistent with the actual object, the relative error of each output variable is less than 2.53%, and the total average relative error of all outputs is about 1.2%. The model has enough accuracy... [more]

The objective of this paper is to describe an energy-based approach to visualize, identify, and monitor faults that may occur in a water-to-water transcritical CO 2 heat pump system. A representation using energy attributes allows the abstraction of all physical phenomena present during operation into a compact and easily interpretable form. The use of a linear graph representation, with heat pump components represented as nodes and energy interactions as links, is investigated. Node signature matrices are used to present the energy information in a compact mathematical form. The resulting node signature matrix is referred to as an attributed graph and is populated in such a way as to retain the structural information, i.e., where the attribute points to in the physical system. To generate the energy and exergy information for the compilation of the attributed graphs, a descriptive thermal−fluid model of the heat pump system is developed. The thermal−fluid model is based on the... [more]

This paper proposes a novel high voltage conversion gain DC/DC boost converter for renewable energy applications and systems. The proposed converter utilizes a three-winding coupled inductor. The presented converter benefits from a unique advantage, as the actual turn ratio of the coupled inductor is decreased in the charging state of the coupled inductor. However, while the inductor is discharging, the actual turn ratio is increased. This feature leads to a very high voltage conversion gain. Furthermore, a passive clamp circuit is employed to recover the leakage current of the coupled inductor. The voltage stresses on the semiconductors are also reduced. In addition, the average current of the primary side of the coupled inductor is zero. This will reduce the total energy stored in the passive elements of the converter. The paper analyzes the Continuous Conduction Mode (CCM) and the operation principles of the presented converter are thoroughly derived. A 250 W laboratory hardware pro... [more]

The increasing penetration of variable renewable energies (VRE) in the European electricity mix requires flexible energy storage systems (ESS), such as pumped storage hydropower (PSH). Disused mining voids from deep closed mines may be used as subsurface reservoirs of underground pumped-storage hydropower (UPSH) plants. Unlike conventional PSH plants, the air pressure in UPSH plants is variable and it differs from the atmospheric conditions. In this paper, the hydraulic transient process of an UPSH plant operating in pumping mode was investigated and a preliminary thermodynamic analysis of the closed surge tank was carried out. Analytical and CFD three-dimensional numerical simulations based on the volume of fluid (VOF) model with two-phase flow have been performed for analyzing the transient process. In the transient simulation, air and water are considered as ideal gas and compressible liquid, respectively. Different guide vanes closing schemes have been simulated. The obtained resul... [more]

Global change, including population growth, economic development and climate change constitute urgent challenges for the smart cities of the 21st century. Cities need to effectively manage their development and meet challenges that have a significant impact on their economic activity, as well as health and quality of life for their citizens. In the context of continuous change, city decision-makers are constantly looking for new smart tools to tackle it. This article addresses this gap, indicating foresight as an effective tool that anticipates the future of a smart city. Its aim is to develop a methodology for planning and implementing a vision of smart city development based on foresight research. The proposed methodology consists of five stages and was developed with the use of methodology for designing hybrid systems. It is an organised, transparent and flexible process which can facilitate the development of sustainable and smart future visions of smart city development by virtue... [more]

To effectively guarantee a secure and stable operation of a smart substation, it is essential to develop a relay protection system considering the real-time online operation state evaluation and the risk assessment of that substation. In this paper, based on action data, defect data, and network message information of the system protection device (PD), a Markov model-based operation state evaluation method is firstly proposed for each device in the relay protection system (RPS). Then, the risk assessment of RPS in the smart substation is carried out by utilizing the risk transfer network. Finally, to highly verify the usefulness and the effectiveness of the proposed method, a case study of a typical 220 kV substation is provided. It follows from the case study that the developed method can achieve a better improvement for the maintenance plan of the smart substation.

The Ukrainian energy sector is one of the most inflexible energy sectors in the world as a result of the almost complete depreciation of the equipment of the main sources of power supply: nuclear, thermal, and hydropower. In connection with existing problems, there is a need to develop and use new energy-saving technologies based on renewable energy sources. In this proposed research, a regression model of renewable energy growth in the energy sector of Ukraine was developed. The studied literature reveals that the independent use of individual functioning elements of renewable energy sources function as the primary power source that is not an optimal solution for stable energy supply. This study proposes the use of hybrid renewable energy systems, namely a combination of two or more renewable energy sources that will help each other to achieve higher energy efficiency, accelerate the growth of renewable energy in the share of the Ukrainian energy sector and/or improve functioning with... [more]

The article analyzes a ground-to-air heat exchanger (GAHE) for a mechanical ventilation system in a building. The heat exchanger’s performance was evaluated in northeastern Poland between May and August of 2016, 2017, and 2018. In spring and summer, the GAHE can be theoretically used to precool air for HVAC systems. The aim of the study was to compare the real-world performance of GAHE with its theoretical performance determined based on the distribution of ground temperature and the temperature at the GAHE outlet modeled in compliance with Standard PN-EN 16798-5 1:2017-07. The modeled values differed considerably from real-world data in May and June, but the model demonstrated satisfactory data fit in July and August. In all years, the modeled average monthly air temperature at the GAHE outlet was 8.3 °C below real-world values in May, but the above difference was only 1.1 °C in August. The developed mathematical model is simple and easy to use, and it can be deployed already in the p... [more]