With about a 7% average annual economic growth rate in Vietnam, the demand for electricity production is increasing, and, with more than 3000 km of coastline, the country has great potential for developing wave energy sources to meet such electricity production. This energy source, also known as renewable energy, comes from tides, wind, heat differences, flows, and waves. Both wind and wave energy are considered to have the most potential for energy sources in Vietnam. Just as hydropower projects are controversial due to depleting water resources and regulating floods, nuclear power projects cause safety concerns. To overcome this problem, Vietnamese scientists are considering using abundant wave energy resources for electricity. Nowadays, the ocean energy sector offers many new technologies to help minimize carbon dioxide emissions (CO2) in the living environment. Further, many countries already have wave power plants. In this research, an integrated model, combining the fuzzy analyti... [more]

A large amount of solid and liquid waste is produced in pesticide production. It is necessary to adopt appropriate disposal processes to reduce pollutant emissions. A co-incineration scheme for mixing multi-component wastes in a rotary kiln was proposed for waste disposal from pesticide production. According to the daily output of solid and liquid wastes, the proportion of mixing was determined. An experiment of the co-incineration of solid and liquid wastes was established. Experimental results showed that the mixed waste could be completely disposed at 850 °C, and the residence time in the kiln exceeded 1 h. A model method for mixture and diesel oil-assisted combustion was proposed. Numerical simulation was performed to predict the granular motion and reveal the combustion interactions of the co-incineration of mixed wastes in the rotary kiln. Simulation results reproduced movements, such as rolling and cascading, and obtained the optimum rotational speed and diesel oil flow for the... [more]

Pipelines are one of the most efficient and economical methods of transporting fluids, such as oil, natural gas, and water. However, pipelines are often subject to leakage due to pipe corrosion, pipe aging, pipe weld defects, or damage by a third-party, resulting in huge economic losses and environmental degradation. Therefore, effective pipeline leak detection methods are important research issues to ensure pipeline integrity management and accident prevention. The conventional methods for pipeline leak detection generally need to extract the features of leak signal to establish a leak detection model. However, it is difficult to obtain actual leakage signal data samples in most applications. In addition, the operating modes of pipeline fluid transportation process often have frequent changes, such as regulating valves and pump operation. Aiming at these issues, this paper proposes a hybrid intelligent method that integrates kernel principal component analysis (KPCA) and cascade suppo... [more]

Composites with high density polyethylene (HDPE) and poly(lactic) acid (PLA) matrix have been tested to analyze the effect of natural fillers (wood flour, recycled wastepaper and a mix of both fillers) and temperature on polymer degradation. Composting tests have been performed in both mesophilic (35 °C) and thermophilic (58 °C) conditions. Degradation development has been evaluated through mass variation, thermogravimetric analysis and differential scanning calorimetry. HDPE, as expected, did not display any relevant variation, confirming its stability under our composting conditions. PLA is sensibly influenced by temperature and humidity, with higher reduction of Mw when composting is performed at 58 °C. Natural fillers seem to influence degradation process of composites, already at 35 °C. In fact, degradation of fillers at 35 °C allows a mass reduction during composting of composites, while neat PLA do not display any variation.

This paper reports a case study using a standardization process for increasing efficiency and a better optimization of resources in a printing company with 150 operators having manual and mechanical tasks in the box assembly department along with four production lines. The current capacity is 350 boxes per day, while the demand is 650 units, where the company is expected to pay large sums for overtime. Using work standardization, studying worker movements, timing, and workstations redesign, the main goal was to increase the efficiency and productivity indexes. After applying those tools, the inefficient movements in operators decreased from 230 to 78, eliminating 66% of the unnecessary movements, as well as the standard time in a workstation decreased from 244 to 199 s (18.44%) per each assembled box, and the production rate increased by 63.2%, that is, 229 units per assembly line a day, where overtime was reduced to zero.

This paper presents a web-based tool for the optimization of biomass-to-chemicals processing pathways. The tool provides a user-friendly grpahical user interface (GUI) for building a process superstructure, offers the possibility of uploading data from Aspen Plus simulations and generates an optimization code to find the pathway that minimizes the annualized costs or maximizes the net present value. A processing pathway from residues to lactic acid is used to discuss and illustrate the main features of the tool.

Two-stage solid-state fermentation strategy was exploited and systematically optimized to enhance Bacillus subtilis growth and sporulation for increasing effective cell number in B. subtilis microbial ecological agents. The first stage focused on improving cell growth followed by the second stage aiming to enhance both cell growth and sporulation. The optimal fermentation condition was that temperature changed from 37 °C to 47 °C at a fermentation time of 48 h and Mn2+ content in medium was 4.9 mg MnSO4/g dry medium. Solid medium properties were improved by the optimal two-stage fermentation. HPLC results demonstrated that glucose utilization was facilitated and low-field nuclear magnetic resonance (LF-NMR) results showed that more active sites in medium for microbial cells were generated during the optimal two-stage fermentation. Moreover, microbial growth and sporulation were enhanced simultaneously during the second stage of fermentation through delaying microbial decline phase and... [more]

The literature has two different perspectives on which innovation types should be implemented to achieve innovation performance; some argue that they should pursue process-oriented innovation, while others maintain that both product- and process-oriented innovation should be performed. Though innovation efficiency should be measured, which takes both input and output variables into account, the research so far has been measured only with the performance of the innovation. Accordingly, this study identifies which innovation type is the most advantageous in terms of innovation efficiency for the chemical firms. We use data of 64 Korean chemical companies from a 2016 Korean innovation survey and perform data envelopment analysis to calculate innovation efficiency. Kruskal−Wallis one-way ANOVA and bootstrap DEA were also conducted to compare the difference of innovation efficiency among groups, depending on which innovation types are oriented. The result shows that focusing on process inno... [more]

A new process for conversion of sugarcane bagasse to ethanol was analyzed for production costs and energy consumption using experimental results. The process includes a sequential three-stage deacetylation, hot water, and disk-refining pretreatment and a commercial glucose-xylose fermenting S. cerevisiae strain. The simultaneous saccharification and co-fermentation (SScF) step used was investigated at two solids loadings: 10% and 16% w/w. Additionally, a sensitivity analysis was conducted for the major operating parameters. The minimum ethanol selling price (MESP) varied between $4.91and $4.52/gal ethanol. The higher SScF solids loading (16%) reduced the total operating, utilities, and production costs by 9.5%, 15.6%, and 5.6%, respectively. Other important factors in determining selling price were costs for fermentation medium and enzymes (e.g., cellulases). Hence, these findings support operating at high solids and producing enzymes onsite as strategies to minimize MESP.

It is well established that the use of synthetic material in water pipes significantly affects the quality of domestic water, especially trace organics that are leached through with the flow of water. In the present study, the migration of volatile organic compounds (VOCs) from water pipes manufactured of polyvinyl chloride (PVC) has been investigated using static laboratory conditions and in residential areas. The contact of deionized water with various PVC pipes for three successive test periods of 24, 48, and 72 h duration has been made. Twenty water samples were collected from houses within Medina Al-Munawarah residential area and were analyzed by using solid phase extraction, followed by high resolution gas chromatography with flame ionized detector (GC-FID). The presence of carbon tetrachloride (CTC), toluene, chloroform, styrene, o-xylene, bromoform (BF), dibromomethane (DBM), cis-1,3-dichloropropane (Cis-1,3-DCP), and trans-1,3-dichloropropane (Trans-1,3-DCP) was initially conf... [more]

In this study, we present the details of an optimization method for parameter estimation of one-dimensional groundwater reactive transport problems using a parallel genetic algorithm (PGA). The performance of the PGA was tested with two problems that had published analytical solutions and two problems with published numerical solutions. The optimization model was provided with the published experimental results and reasonable bounds for the unknown kinetic reaction parameters as inputs. Benchmarking results indicate that the PGA estimated parameters that are close to the published parameters and it also predicted the observed trends well for all four problems. Also, OpenMP FORTRAN parallel constructs were used to demonstrate the speedup of the code on an Intel quad-core desktop computer. The parallel code showed a linear speedup with an increasing number of processors. Furthermore, the performance of the underlying optimization algorithm was tested to evaluate its sensitivity to the va... [more]

In this work, we report on the different sizes of manganese-doped cadmium selenide quantum dots (Mn-doped CdSe QDs) synthesized for 0 to 90 min using a reverse micelle organic solvent method and surfactant having a zinc blende structure, with physical size varying from 3 to 14 nm and crystallite size from 2.46 to 5.46 nm and with a narrow size distribution. At similar reaction times, Mn-doped CdSe QDs displayed the growth of larger QDs compared with the pure CdSe QDs. Due to the implementation of lattice strain owing to the inclusion of Mn atoms in the CdSe QD lattice, the lattice parameter was compressed as the QD size increased. Strain was induced by the particle size reduction, as observed from X-ray diffractometer (XRD) analysis. The analyses of the strain effect on the QD reduction are discussed relative to each of the XRD characteristics.

Taking the open circuit hydraulic pump-controlled forging press system as the research object, according to the problems of pressure-relief impact of this system, the pressure-relief rules, mathematic models of the energy release rules, and the flow release rules were established, and the pressure-relief performance in different stages of each pressure-relief curve was analyzed. Based on the different requirements of the pressure gradient decrease, the combined pressure-relief curve (CPRC) was proposed to realize variable-pump eccentric magnitude planning. An experimental study on the pressure-relief process with CPRC was carried out. The results show that the pressure fluctuation of the pressure-relief pipe was reduced and the suppression effect of pressure-relief impact was better than that of the single regular pressure-relief curve. When the initial pressures were 10 MPa and 15 MPa, the pressure impact of the pressure-relief tube decreased by 45.45% and 37.5%, respectively, which r... [more]

Laminar fluid flow and advection-dominant transport produce ineffective mixing conditions in micromixers. In these systems, a desirable fluid mixing over a short distance may be achieved using special geometries in which complex flow paths are generated. In this paper, a novel design, utilizing semi-circular ridges, is proposed to improve mixing in micro channels. Fluid flow and scalar transport are investigated employing Computational Fluid Dynamics (CFD) tool. Mixing dynamics are investigated in detail for alternative designs, injection, and diffusivity conditions. Results indicate that the convex alignment of semi-circular elements yields a specific, helicoidal-shaped fluid flow along the mixing channel which in turn enhances fluid mixing. In all cases examined, homogenous concentration distributions with mixing index values over 80% are obtained. When it is compared to the classical T-shaped micromixer, the novel design increases mixing index and mixing performance values by the fa... [more]

Processing biodiesel from non-edible sources of feedstock seems to be thriving in recent years. It also has also gathered more attention than in the past, mainly because the biodiesel product is renewable and emits lower pollution compared to fossil fuels. Researchers have started their work on various kinds of biodiesel product, especially from a non-edible feedstock. Non-edible feedstocks such as Ceiba pentandra show great potential in the production of biodiesel, especially in the Southeast Asia region because the plants seem to be abundant in that region. Ceiba pentandra, also known as the Kapok tree, produces hundreds of pods with a length of 15 cm (5.9 in) and diameter 2−5 cm (1−2 in). The pods consist of seeds and fluff in the surrounding areas inside the pod, which itself contains yellowish fibre, a mixture of cellulose and lignin. The seeds of Ceiba pentandra can be used as feedstock for biodiesel production. The study for Ceiba pentandra will involve techno-economic, as well... [more]

The composting process of organic fraction of municipal solid waste, besides to the residual compost, generates a wastewater that is characterized by a high organic load. The application of anaerobic processes represents an advantageous solution for the treatment and valorization of this type of wastewater. Nevertheless, few works have been focused on the anaerobic digestion of compost leachate. To overcome this dearth, in the present paper an extensive experimental investigation was carried out to develop and analyse the anaerobic treatment of young leachate in completely stirred tank reactors (CSTR). Initially, it was defined a suitable leachate pretreatment to correct its acidic characteristics that is potentially able to inhibit methanogenic biomass activity. The pretreated leachate was fed to the digester over the start-up phase that was completed in about 40 days. During the operational period, the organic load rate (OLR) changed between 4.25 kgCOD/m3d and 38.5 kgCOD/m3d. The che... [more]

Carbon dioxide is one of the major greenhouse gases and a leading source of global warming. Several adsorbent materials are being tested for removal of carbon dioxide (CO2) from the atmosphere. The use of multiwalled carbon nanotubes (MWCNTs) as a CO2 adsorbent material is a relatively new research avenue. In this study, Fe2O3/Al2O3 composite catalyst was used to synthesize MWCNTs by cracking ethylene gas molecules in a fluidized bed chemical vapor deposition (CVD) chamber. These nanotubes were treated with H2SO4/HNO3 solution and functionalized with 3-aminopropyl-triethoxysilane (APTS). Chemical modification of nanotubes removed the endcaps and introduced some functional groups along the sidewalls at defected sites. The functionalization of nanotubes with amine introduced carboxylic groups on the tube surface. These functional groups significantly enhance the surface wettability, hydrophilicity and CO2 adsorption capacity of MWCNTs. The CO2 adsorption capacity of as-grown and amine-fu... [more]

Power loss due to the aeroelastic effect of the blade is becoming an important problem of large-scale blade design. Prior work has already employed the pretwisting method to deal with this problem and obtained some good results at reference wind speed. The aim of this study was to compensate for the power loss for all of the wind speeds by using the pretwisting method. Therefore, we developed an aeroelastic coupling optimization model, which takes the pretwist angles along the blade as free variables, the maximum AEP (annual energy production) as the optimal object, and the smooth of the twist distribution as one of the constraint conditions. In this optimization model, a PSO (particle swarm optimization) algorithm is used and combined with the BEM-3DFEM (blade element momentum—three-dimensional finite element method) model. Then, the optimization model was compared with an iteration method, which was recently developed by another study and can well compensate the power loss at referen... [more]

An investigation on the two-phase flow field inside a grooved rotating-disk system is presented by experiment and computational fluid dynamics numerical simulation. The grooved rotating-disk system consists of one stationary flat disk and one rotating grooved disk. A three-dimensional computational fluid dynamics model considering two-phase flow and heat transfer was utilized to simulate phase distributions and heat dissipation capability. Visualization tests were conducted to validate the flow patterns and the parametric effects on the flow field. The results indicate that the flow field of the grooved rotating-disk system was identified to be an air−oil flow. A stable interface between the continuous oil phase and the two-phase area could be formed and observed. The parametric analysis demonstrated that the inter moved outwards in the radial direction, and the average oil volume fraction over the whole flow field increased with smaller angular speed, more inlet mass flow of oil, or d... [more]

In this work, gold nanostar (AuNPs) and gold nanodendrites were synthesized by one-pot and environmentally friendly approach in the presence of gelatin. Influence of gelatin concentrations and reaction conditions on the growth of branched (AuNPs) were investigated further. Interestingly, the conversion of morphology between dendritic and branched nanostructure can be attained by changing the pH value of gelatin solution. The role of gelatin as a protecting agent through the electrostatic and steric interaction was also revealed. Branched nanoparticles were characterized by surface plasmon resonance spectroscopy (SPR), transmission electron microscopy (TEM), XRD, dynamic light scattering (DLS) and zeta-potential. The chemical interaction of gelatin with branched gold nanoparticles was analyzed by Fourier transform infrared spectroscopy (FT-IT) technique. Ultraviolet visible spectroscopy results indicated the formation of branched gold nanoparticles with the maximum surface plasmon reson... [more]

A hydrothermal pretreatment of the microalga Nannochloropsis gaditana at mild temperatures was studied in order to reduce the N and O content in the biocrude obtained by hydrothermal liquefaction (HTL). The work focused on the evaluation of temperature, reactor loading, and time (factors) to maximize the yield of the pretreated biomass and the heteroatom contents transferred from the microalga biomass to the aqueous phase (responses). The study followed the factorial design and response surface methodology. An equation for every response was obtained, which led to the accurate calculation of the operating conditions required to obtain a given value of these responses. Temperature and time are critical factors with a negative effect on the pretreated biomass yield but a positive one on the N and O recovery in the aqueous phase. The slurry concentration has to be low to increase heteroatom recovery and has to be high to maximize the pretreated microalga yields. Response equations were ob... [more]

The effects of single-arc blade profile length on the performance of a forward multiblade fan are investigated in this paper by computational fluid dynamics and experimental measurement. The present work emphasizes that the use of a properly reduced blade inlet angle (β1A) and properly improved blade outlet angle (β2A) is to increase the length blade profile, which suggests a good physical understanding of internal complex flow characteristics and the aerodynamic performance of the fan. Numerical results indicate that the gradient of the absolute velocity among the blades in model-L (reducing the blade inlet angle and improving blade outlet angle) is clearly lower than that of the baseline model and model-S (improving the blade inlet angle and reducing blade outlet angle), where a number of secondary flows arise on the exit surface of baseline model and model-S. However, no secondary flow occurs in model-L, and the flow loss at the exit surface of the volute (scroll-shaped flow pattern... [more]

The aim of the present study is to investigate the multiple slip effects on magnetohydrodynamic unsteady Maxwell nanofluid flow over a permeable stretching sheet with thermal radiation and thermo-diffusion in the presence of chemical reaction. The governing nonlinear partial differential equations are transformed into a system of coupled nonlinear ordinary differential equations with the aid of appropriate similarity variables, and the transformed equations are then solved numerically by using a variational finite element method. The effects of various physical parameters on the velocity, temperature, solutal concentration, and nanoparticle concentration profiles as well as on the skin friction coefficient, rate of heat transfer, and Sherwood number for solutal concentration are discussed by the aid of graphs and tables. An exact solution of flow velocity, skin friction coefficient, and Nusselt number is compared with the numerical solution obtained by FEM and also with numerical resul... [more]

Ginkgo biloba leaves are well known for their high content of nutrients and bioactive substances. However, unpleasant smell and a small number of ginkgolic acids greatly reduce the utilization of the leaves. In this work, solid-state fermentation of G. biloba leaves using Eurotium cristatum was studied by investigation of the nutrient changes and its feasibility as a functional feed. E. cristatum could grow on pure G. biloba leaves and the addition of excipients could significantly improve the growth of E. cristatum. The optimal medium was with 10% (w/w) of whole G. biloba seeds and the optimized water content, pH, inoculum size and fermentation time were 45% (w/w), 4.5, 4.76 × 107 CFU/100 g wet medium, and eight days, respectively. Under the optimal conditions, the spore number increased by about 40 times. The content of flavonoids was greatly increased by 118.6%, and the protein and polyprenyl acetates (PPAs) were increased by 64.9% and 10.6%, respectively. The ginkgolic acids, ligni... [more]

This paper studies heat transfer in a two-dimensional magnetohydrodynamic viscous incompressible flow in convergent/divergent channels. The temperature profile was obtained numerically for both cases of convergent/divergent channels. It was found that the temperature profile increases with an increase in Reynold number, Prandtl number, Nusselt number and angle of the wall but decreases with an increase in Hartmann number. A relatively new numerical method called the spectral homotopy analysis method (SHAM) was used to solve the governing non-linear differential equations. The SHAM 3rd order results matched with the DTM and shooting, showing that SHAM is feasible as a technique to be used.