Technological development in latent heat storage (LHS) systems is essential for energy security and energy management for both renewable and non-renewable sources. In this article, numerical analyses on a shell-and-tube-based LHS system with coupled thermal enhancement through extended fins and nano-additives are conducted to propose optimal combinations for guaranteed higher discharging rate, enthalpy capacity and thermal distribution. Transient numerical simulations of fourteen scenarios with varied combinations are investigated in three-dimensional computational models. The shell-and-tube includes paraffin as phase change material (PCM), longitudinal, radial and wire-wound fins and graphene nano-platelets (GNP) as extended fins and nano-additives, respectively. The extended fins have demonstrated better effectiveness than nano-additives. For instance, the discharging durations for paraffin with longitudinal, radial and wire-wound fins are shortened by 88.76%, 95.13% and 96.44% as co... [more]

The growing share of renewable energies in power production and the rise of the market share of battery electric vehicles increase the demand for battery technologies. In both fields, a predictable operation requires knowledge of the internal battery state, especially its state of charge (SoC). Since a direct measurement of the SoC is not possible, Kalman filter-based estimation methods are widely used. In this work, a step-by-step guide for the implementation and tuning of an extended Kalman filter (EKF) is presented. The structured approach of this paper reduces efforts compared with empirical filter tuning and can be adapted to various battery models, systems, and cell types. This work can act as a tutorial describing all steps to get a working SoC estimator based on an extended Kalman filter.

The drought that occurred in Zimbabwe in 2020 affected the country’s main hydro-power station causing the electricity supply to be less secure and reliable. This challenge resulted in load-shedding, which is not desirable to mining companies that require constant and reliable power for their operations. In that regard, a techno-economic analysis was carried out to assess the potential of integrating concentrated solar power (+thermal storage) and photovoltaics (+battery storage) to supply power at a typical mine in Zimbabwe. Two scenarios were simulated—a base case with no exports to the grid and another case where exports were allowed. The models were evaluated based on the generated renewable energy offsetting the demand from the mine, the energy exported, the grid contribution, the levelised cost of electricity and the net present value. The results show that the addition of a battery storage system to PV improves the percentage of the load offset by the renewable system and the gen... [more]

Ocean renewable wave power is one of the more encouraging inexhaustible energy sources, with the potential to be exploited for nearly 337 GW worldwide. However, compared with other sources of renewables, wave energy technologies have not been fully developed, and the produced energy price is not as competitive as that of wind or solar renewable technologies. In order to commercialise ocean wave technologies, a wide range of optimisation methodologies have been proposed in the last decade. However, evaluations and comparisons of the performance of state-of-the-art bio-inspired optimisation algorithms have not been contemplated for wave energy converters’ optimisation. In this work, we conduct a comprehensive investigation, evaluation and comparison of the optimisation of the geometry, tether angles and power take-off (PTO) settings of a wave energy converter (WEC) using bio-inspired swarm-evolutionary optimisation algorithms based on a sample wave regime at a site in the Mediterranean S... [more]

Electric vehicle (EV) use is growing at a steady rate globally. Many countries are planning to ban internal combustion engines by 2030. One of the key issues needed to be addressed before the full-scale deployment of EVs is ensuring energy security. Various studies have developed models to simulate and study hourly electricity demand from EV charging. In this study, we present an improved model based on discrete event simulation, which allows for modeling characteristics of individual EV users, including the availability of electric vehicle supply equipment (EVSE) outside homes and the charging threshold of each EV user. The model is illustrated by simulating 1000 random electric vehicles generated using data from an actual survey. The results agree with previous studies that daily charging demands do not significantly vary. However, the results show a significant shift in charging schedule during weekends. Moreover, the simulation demonstrated that the charging peak demand can be redu... [more]

Global energy sources are being transformed from hydrocarbon-based energy sources to renewable and carbon-free energy sources such as wind, solar and hydrogen. The biggest challenge with hydrogen as a renewable energy carrier is the storage and delivery system’s complexity. Therefore, other media such as ammonia for indirect storage are now being considered. Research has shown that at reasonable pressures, ammonia is easily contained as a liquid. In this form, energy density is approximately half of that of gasoline and ten times more than batteries. Ammonia can provide effective storage of renewable energy through its existing storage and distribution network. In this article, we aimed to analyse the previous studies and the current research on the preparation of ammonia as a next-generation renewable energy carrier. The study focuses on technical advances emerging in ammonia synthesis technologies, such as photocatalysis, electrocatalysis and plasmacatalysis. Ammonia is now also stro... [more]

Nowadays, increasingly stricter regulations on emission reduction are inducing rapid developments in combustion science. Low-temperature combustion (LTC) is an advanced combustion technology that increases an engine’s thermal efficiency and even provides low emissions of nitrogen oxides (NOx) and particulate matter (PM). The technology often uses early direct injections to achieve sufficient mixture homogeneity. This leads to increasing wall wetting and lower combustion efficiency. This paper introduces the Multipulse ballistic injection (MBI) method to improve combustion with early injection timings. The research was carried out in a four-cylinder medium-duty diesel engine with high-pressure exhaust gas recirculation (HP-EGR). The investigation was divided into two experiments. In the first experiment, MBI was examined without EGR, and in the second, EGR was applied to study its effects. It was found that the MBI strategy decreased wall wetting and increased homogeneity and the indica... [more]

Heat transfer enhancement techniques used in liquid piston gas compression can contribute to improving the efficiency of compressed air energy storage systems by achieving a near-isothermal compression process. This work examines the effectiveness of a simultaneous use of two proven heat transfer enhancement techniques, metal wire mesh inserts and spray injection methods, in liquid piston gas compression. By varying the dimension of the inserts and the pressure of the spray, a comparative study was performed to explore the plausibility of additional improvement. The addition of an insert can help abating the temperature rise when the insert does not take much space or when the spray flowrate is low. At higher pressure, however, the addition of spacious inserts can lead to less efficient temperature abatement. This is because inserts can distract the free-fall of droplets and hinder their speed. In order to analytically account for the compromised cooling effects of droplets, Reynolds n... [more]

A new type of stepped seal with a ribbed casing is proposed to efficiently reduce the leakage at the tips of turbine blades. The leakage characteristics of two different types of labyrinth seals (conventional seal vs. ribbed seal) were compared and analyzed through computational fluid dynamics (CFD) in a wide operating range of pressure ratios and clearances. The analysis showed that the ribbed seal has superior leakage performance to the conventional seal at all clearance sizes. With the same clearance size (S/H = 1.0), the flow function of the ribbed seal was approximately 21.5−42.6% less than that of the conventional seal. Also, different trends of variation in the flow function according to the increase of the clearance were found between the conventional and ribbed seals. The leakage flow inside the labyrinth seal was analyzed to explain the cause of this difference in tendency, and it was confirmed that the added ribs cause collision between the leakage flow and the tooth wall, e... [more]

This work investigates the effect of production scales (laboratory, bench, and pilot) by pyrolysis of Açaí (Euterpe oleracea Mart.) seeds at 450 °C and 1.0 atmosphere, on the yields of reaction products and acid value of bio-oils. The experiments were carried out in batch mode using a laboratory scale reactor of 143 mL, a bench scale reactor of 1.5 L, and a pilot scale reactor of 143 L (≈1:10:1000). The bio-oil was obtained in pilot scale, fractionated by distillation to produce biofuel-like fractions. The distillation of bio-oil was carried out in a laboratory column. The physical-chemistry properties (density, kinematic viscosity, acid value, and refractive index) of bio-oils and distillation fractions were determined. The qualitative analysis was determined by FT-IR and the chemical composition by GC-MS. The pyrolysis showed bio-oil yields from 4.37 to 13.09 (wt.%), decreasing with reactor volume. The acid value of bio-oils varied from 68.31 to 70.26 mg KOH/g. The distillation of bi... [more]

The variability in generation introduced in the electrical system by an increasing share of renewable technologies must be addressed by balancing mechanisms, demand response being a prominent one. In parallel, the massive introduction of smart meters allows for the use of high frequency energy use time series data to segment electricity customers according to their demand response potential. This paper proposes a smart meter time series clustering methodology based on a two-stage k-medoids clustering of normalized load-shape time series organized around the day divided into 48 time points. Time complexity is drastically reduced by first applying the k-medoids on each customer separately, and second on the total set of customer representatives. Further time complexity reduction is achieved using time series representation with low computational needs. Customer segmentation is undertaken with only four easy-to-interpret features: average energy use, energy−temperature correlation, entrop... [more]

Combined systems for power production and thermally activated cooling have a high potential for improving the efficiency and utilisation of thermal systems. In this regard, various configurations have been proposed and are comprehensively reviewed. They are primarily based on absorption systems and the implementation of multiple levels of complexity and flexibility. The configuration of the absorption power and cooling combined cycle proposed herein has wide commercial applicability owing to its simplicity. The configuration of the components is not new. However, the utilisation of aqueous salt solutions, the comparison with ammonia chiller and with absorption power cycles, the focus on parameters that are important for real-life applications, and the comparison of the performances for constant heat input and waste heat recovery are novel. The proposed cycle is also compared with a system based on the organic Rankine cycle and vapour compression cycle. An investigation of its performan... [more]

In this study, we present the wind distributions from a long-term offshore met mast and a novel approach based on the measure−correlate−predict (MCP) method from short-term onshore-wind-turbine data. The annual energy production (AEP) and capacity factors (CFs) of one onshore and four offshore wind-turbine generators (WTG) available on the market are evaluated on the basis of wind-distribution analysis from both the real met mast and the MCP method. Here, we also consider the power loss from a 4-month light detection and ranging (LiDAR) power-curve test on an onshore turbine to enhance the accuracy of further AEP and CF evaluations. The achieved Weibull distributions could efficiently represent the probability distribution of wind-speed variation, mean wind speed (MWS), and both the scale and shape parameters of Weibull distribution in Taiwan sites. The power-loss effect is also considered when calculating the AEPs and CFs of different WTGs. Successful offshore wind development require... [more]

The combined operation of hybrid wind power and a battery energy storage system can be used to convert cheap valley energy to expensive peak energy, thus improving the economic benefits of wind farms. Considering the peak−valley electricity price, an optimization model of the economic benefits of a combined wind−storage system was developed. A charging/discharging strategy of the battery storage system was proposed to maximize the economic benefits of the combined wind−storage system based on the forecast wind power. The maximal economic benefits were obtained based on scenario analysis, taking into account the wind-power forecast error, and costs associated with the loss of battery life, battery operation, and maintenance. Case simulation results highlight the effectiveness of the proposed model. The results show that the hybrid wind−storage system is not only able to convert cheap electricity in the valley period into expensive electricity in the peak period, thus resulting in higher... [more]

This paper proposes a three-phase isolated flyback inverter (IFBI) for single-stage grid-tied solar PV applications, considering a simple sinusoidal pulse-width modulation (SPWM) scheme. The proposed single-stage inverter employs a reduced passive elements count by considering three input-parallel output-differential (IPOD) flyback converter modules. Additionally, a single small size LC-input low-pass filter is utilized at the input paralleling point for ripple-free input current operation, which is essential in grid-connected renewable energy applications. In addition, a mathematical model of the IFBI is presented to confirm the existence of its low-order harmonic components. A simple PI controller-based control scheme, considering only two loops and five sensors, is used to control the proposed grid-tied IFBI. Continuous modulation scheme (CMS) combined with SPWM is used to diminish the low-frequency harmonic components. Moreover, a simple selective harmonic elimination (SHE) loop is... [more]

Contrary to the extensive amount of research on large wind turbines, substantial analyses of small wind turbines are still rare. In the present study, the wind energy potential of three locations in Poland is analyzed using real wind data from a five-year period and the parameters of the selected turbine model. Appropriate simulations are performed to assess the energy efficiency of the analyzed investments at a coastal, foothill, or lowland site. According to the results, the most favorable location for a small wind turbine is the coastal site (wind zone I). The payback time at this location is approximately 13 years, whereas the payback times at the other two analyzed are more than 3 times longer. The payback periods for the latter locations significantly exceed the estimated lifetime of the wind turbine, ruling out their economic viability. The cost of electricity generation varies greatly, from 0.16 EUR/kWh at the coastal location to 0.71 EUR/kWh at the lowland location. These resu... [more]

In this study, ultrasound was used to accelerate two-stage (esterification−transesterification) catalytic synthesis of biodiesel from used cooking oil, which originally had a high acid value (4.35 mg KOH/g). In the first stage, acid-catalyzed esterification reaction conditions were developed with a 9:1 methanol/oil molar ratio, sulfuric acid dosage at 2 wt %, and a reaction temperature of 60 °C. Under ultrasound irradiation for 40 min, the acid value was effectively decreased from 4.35 to 1.67 mg KOH/g, which was decreased to a sufficient level (<2 mg KOH/g) to avoid the saponification problem for the subsequent transesterification reaction. In the following stage, base-catalyzed transesterification reactions were carried out with a 12:1 methanol/oil molar ratio, a sodium hydroxide dosage of 1 wt %, and a reaction temperature of 65 °C. Under ultrasound-assisted transesterification for 40 min, the conversion rate of biodiesel reached 97.05%, which met the requirement of EN 14214 stan... [more]

Natural gas hydrate is an important energy source. Therefore, it is extremely important to provide a clear imaging profile to determine its distribution for energy exploration. In view of the problems existing in conventional migration methods, e.g., the limited imaging angles, we proposed to utilize an amplitude-preserved one-way wave equation migration based on matrix decomposition to deal with primary and multiple waves. With respect to seismic data gathered at the Chilean continental margin, a conventional processing flow to obtain seismic records with a high signal-to-noise ratio is introduced. Then, the imaging results of the conventional and amplitude-preserved one-way wave equation migration methods based on primary waves are compared, to demonstrate the necessity of implementing amplitude-preserving migration. Moreover, a simple two-layer model is imaged by using primary and multiple waves, which proves the superiority of multiple waves in imaging compared with primary waves a... [more]

This paper summarizes and discusses some critical aspects of flying hypersonically. The first is the L/D (lift over drag) ratio determining thrust and that in turn depends on the slenderness Küchemann’s τ parameter. This second parameter is found to depend on the relative importance of wave versus friction drag. Ultimately, all engineering drag is argued to depend on vorticity formed at the expense of the vehicle kinetic energy, thus requiring work by thrust. Different mixing strategies are discussed and shown to depend also on mechanisms forming vorticity when the regime is compressible. Supersonic combustion is briefly analyzed and found, at sufficiently high combustor Mach, to take place locally at constant volume, unlike conventional Brayton cycles.

The state of charge (SOC) prediction for an electric vehicle battery pack is critical to ensure the reliability, efficiency, and life of the battery pack. Various techniques and statistical systems have been proposed in the past to improve the prediction accuracy, reduce complexity, and increase adaptability. Machine learning techniques have been vigorously introduced in recent years, to be incorporated into the existing prediction algorithms, or as a stand-alone system, with a large amount of recorded past data to interpret the battery characteristics, and further predict for the present and future. This paper presents an overview of the machine learning techniques followed by a proposed pre-processing technique employed as the input to the long short-term memory network (LSTM) algorithm. The proposed pre-processing technique is based on the time-based sliding window algorithm (SW) and the Shapley additive explanation theory (SHAP). The proposed technique showed improvement in accurac... [more]

Voltages of electric double-layer capacitor (EDLC) modules vary rather wider than traditional secondary batteries. Although EDLCs should desirably be cycled in a voltage range as wide as possible to achieve a high energy utilization ratio, the wide voltage variation of EDLC modules impairs the performance of DC−DC converters. To address such issues, previous works reported series-parallel reconfiguration techniques, which are roughly divided into balance- and unbalance-shift circuits. However, conventional balance-shift circuits are not applicable to modules comprising odd number cells, impairing modularity. Unbalance-shift circuits, on the other hand, unavoidably cause cell voltage imbalance that reduces energy utilization ratio. This paper proposes a novel series-parallel reconfigurable EDLC module with cell voltage equalization capability. The proposed reconfigurable EDLC module is applicable to any number of cells, realizing good modularity. Furthermore, all cells in the proposed m... [more]

Power generation units based on the bio-syngas system face two main challenges due to (i) the possible temporary shortage of primary sources and (ii) the engine power derating associated with the use of low-energy density fuels in combustion engines. In both cases, an external input fuel is provided. Hence, complementing syngas with traditional fuels, like natural gas, becomes a necessity. In this work, an experimental methodology is proposed, aiming at the quantification of the impact of the use of both natural gas and syngas in spark ignition (SI) engines on performance and emissions. The main research questions focus on investigating brake thermal efficiency (BTE), power derating, and pollutant emission (NOx, CO, THC, CO2) formation, offering quantitative findings that present the basis for engine optimization procedures. Experimental measurements were performed on a Toyota 4Y-E engine (a 4-cylinders, 4-stroke spark ignition engine) at partial load (10 kW) under different syngas ene... [more]

Distributed generation (DG) systems are growing in number, diversifying in driving technologies and providing substantial energy quantities in covering the energy needs of the interconnected system in an optimal way. This evolution of technologies is a response to the needs of the energy transition to a low carbon economy. A nanogrid is dependent on local resources through appropriate DG, confined within the boundaries of an energy domain not exceeding 100 kW of power. It can be a single building that is equipped with a local electricity generation to fulfil the building’s load consumption requirements, it is electrically interconnected with the external power system and it can optionally be equipped with a storage system. It is, however, mandatory that a nanogrid is equipped with a controller for optimisation of the production/consumption curves. This study presents design consideretions for nanogrids and the design of a nanogrid system consisting of a 40 kWp photovoltaic (PV) system... [more]

The construction and commissioning of renewable energy sources is one of the priority areas of energy programs aimed at achieving sustainable development goals. The creation and operation of such sources is associated with significant risks, the management of which is based on real insurance instruments. This article focuses on the formation of a model for assessing the use of insurance in renewable energy projects and presents the business process, stages, risk drivers, and calculation of the economic efficiency of the use of insurance mechanisms in renewable energy projects.

We developed a new wind turbine system that consists of a diffuser shroud with a broad-ring brim at the exit periphery and a wind turbine inside it. The shrouded wind turbine with a brimmed diffuser, which we called a “wind lens turbine” (WLT), has demonstrated power augmentation by a factor of about 2−5 compared with a bare wind turbine for a given turbine diameter and wind speed. The increase in power output depends on the diffuser shape and length and the brim height. However, a simple theory presented in this paper argues that only two performance coefficients are needed to predict the performance of WLT. The coefficients are the back pressure coefficient of the brim and the pressure recovery coefficient of the diffuser. We theoretically showed that the back pressure coefficient was particularly important for the performance of WLT. Finally, the simple theory was evaluated with experimental results. The results showed good agreement with each other.