This paper focuses on a detailed numerical investigation combined with experimental research for a non-premixed swirl combustor, which aims to analyze the effects of the blade angle of the outer swirler and equivalence ratio on flow and combustion characteristics. In the experiment, the temperature in the furnace was obtained with a thermocouple, while a realizable k-ε turbulence model and two-step reaction mechanism of methane and air are used in the numerical method. The calculation results are in good agreement with the experimental data. The results reveal that the air flow rate through the swirler accounts for a small amount of the total air due to the influence of the draft fan, and there is no central recirculation zone (CRZ) despite the presence of the swirler. It was also found that NO emissions gradually decrease as the blade angle of the outer swirler increases. It was also indicated that the average temperature is 100 K higher than the general combustor with a 58° blade ang... [more]

The necessity to control the feed water state in the second loop of a nuclear power plant nuclear reactor is justified. The different methods of the state control of flowing water in the pipeline are reviewed. It has been established that controlling the feed water state should not result in irreversible changes in its chemical composition and physical structure. A change in the composition or structure of feed water leads to a change in its heat capacity. The heat transfer deteriorates, the production of electrical energy in the installation decreases, and the additional release of heat into the atmosphere increases. This process also occurs during the heat capacity changes for other reasons. The method for controlling the feed water heat capacity by measuring the value of the refractive index n is developed. The design of a flow-through refractometer based on the total internal reflection for control of the feed water state in the stream is made. The dependence of the heat capacity c... [more]

Fin efficiency, as a measure of the effectiveness of the heat transfer enhancement, is of great importance in studying the heat transfer performance of H-type finned tube banks. The fin efficiency of square fins is adopted by most researchers as an alternative to that of H-type fins, which can create certain errors in the fin efficiency of H-type fins. For this paper, the linear nomograms and fitting formulae of fin efficiency of H-type fins are obtained by the definition method of fin efficiency based on numerous numerical simulations, and the results calculated by this method are verified by experimental data. On this basis, the effects of three geometric parameters (slit width, fin height, and fin thickness) and two thermal parameters (surface heat transfer coefficient and fin thermal conductivity) on the fin efficiency of H-type fins are also investigated and compared to those of square fins. The results indicate that the fin efficiency of H-type fins increases with the increment o... [more]

The omnipresence of risk prevails in almost every aspect of human life. Individuals and societal factors are pivotal in the decision-making process to judge acceptability and tolerability of risk. Tolerability of risk (ToR) is characterized by dynamism pinned in the process of decision making that helps to gauge the society and individual’s risk. The energy transition implies switching the energy system from fossil fuels or any traditional mechanism to modern renewable sources that are sustainable. The energy transition is paramount important in the current global energy system to attain sustainable goals for organizations. This study used the positivism research paradigm to address the research questions. The quantitative approach helps to examine the cause-and-effect relationship. It also helps to collect systematic information to meet the objectives of the research. A total sample of 300 was selected for the data collection from renewable energy companies. The study used positivism... [more]

Unmanned Aerial Vehicle (UAV) propulsion technology is significantly related to the flight performance of UAVs, which has become one of the most important development directions of aviation. It should be noted that UAVs have three types of propulsion systems, namely the fuel, hybrid fuel-electric, and pure electric, respectively. This paper presents and discusses the classification, working principles, characteristics, and critical technologies of these three types of propulsion systems. It is helpful to establish the development framework of the UAV propulsion system and provide the essential information on electric propulsion UAVs. Additionally, future technologies and development, including the high-power density motors, converters, power supplies, are discussed for the electric propulsion UAVs. In the near future, the electric propulsion system would be widely used in UAVs. The high-power density system would become the development trend of electric UAVs. Thus, this review article... [more]

In the age of COVID, the regaining of economies appears mostly imperative, and rural areas could play a crucial role in this framework. The question of inhabitants’ dispersion and low density, and the exodus of rural people to bigger urban centers have determined an adverse effect on rural development. Rural isolation rises to be a higher order good, delivering a higher degree of security in the pandemic context for those seeking refuge from gatherings of cities. Rural areas provide food, natural environments, and resources that help occupations, development, and wealth trends and preserve cultural heritage. Consequently, rural spaces are vital for several motives and thus it is essential to focus on issue of rural development, especially since lacking rural development does not allow dialoging about development in a regional and/or national perspective. This paper investigates the stakeholders’ impact on rural development, by considering the increasing role of stakeholders as well as... [more]

Edge computing is a distributed computing paradigm such that client data are processed at the periphery of the network, as close as possible to the originating source. Since the 21st century has come to be known as the century of data due to the rapid increase in the quantity of exchanged data worldwide (especially in smart city applications such as autonomous vehicles), collecting and processing such data from sensors and Internet of Things devices operating in real time from remote locations and inhospitable operating environments almost anywhere in the world is a relevant emerging need. Indeed, edge computing is reshaping information technology and business computing. In this respect, the paper is aimed at providing a comprehensive overview of what edge computing is as well as the most relevant edge use cases, tradeoffs, and implementation considerations. In particular, this review article is focused on highlighting (i) the most recent trends relative to edge computing emerging in t... [more]

Induction motors are widely used in industry and are essential to industrial processes. The faults in motors lead to high repair costs and cause financial losses resulting from unexpected downtime. Early detection of faults in induction motors has become necessary and critical in reducing costs. Most motor faults are caused by bearing failure. Machine learning-based diagnostic methods are proposed in this study. These methods use effective features. First, load currents of healthy and faulty motors are measured while the rotating speed is changing continuously. Second, experiments revealed the relationship between the magnitude of the amplitude of specific signals and the rotating speed, and the rotating speed is treated as a new feature. Third, machine learning-based diagnoses are conducted. Finally, the effectiveness of machine learning-based diagnostic methods is verified using experimental data.

The on-site measurement of transient voltages is of great significance in analyzing the fault cause of power systems and optimizing the insulation coordination of power equipment. Conventional voltage transformers normally have a narrow bandwidth and are unable to accurately measure various transient voltages in power systems. In this paper, a wideband parallel resistive−capacitive voltage divider is developed, which can be used for online monitoring of transient voltages in a 220 kV power grid. The structures of the high-voltage and low-voltage arms were designed. The internal electric field distribution of the high-voltage arm was analyzed. The influence factors and improvement techniques of the upper frequency limit were studied. The parameters of the elements of the divider were determined. The voltage withstand performances and scale factors under lightning impulses and AC and DC voltages, the temperature stabilities of scale factors and the step response and bandwidth of the deve... [more]

As with all transport modes, the maritime sector is undergoing a drastic transition towards net zero, similar to the path in which Aviation is already engaged through global decarbonization programs such as CORSIA for the International Civil Aviation Organization, or the Emission trading Scheme of the European Union). Maritime indeed shares with Aviation a common element: the difficulty of shifting to electric in the short to medium term. Therefore, the use of sustainable fuels represents the main and only relevant option in this timeframe. As sustainable biofuels will be used as blend components in the case of large-scale deployment, it is necessary to investigate the behavior of bio- and fossil-based fuels when mixed in various percentages, in particular for low quality products such as HTL (HydroThermal Liquefaction) and fast pyrolysis oils from lignocellulosic biomass and waste. Biocrude from subcritical hydrothermal liquefaction of undigested sewage sludge, produced at reaction co... [more]

In order to achieve Australia’s greenhouse gas emissions reduction targets, a majority of the existing residential building stock in Australia will require retrofitting in favour of energy-efficient solutions. This paper considers retrofitting for conditioning to be one of the most straightforward and offers the greatest potential to deliver significant comfort and energy-saving results. Radiant conditioning systems are not new, yet some game-changing innovations have taken place over the last decade that may require an entire paradigm shift in the manner we condition our buildings. The reiteration of the principle ‘thermally active systems’ suggests that our buildings need to accommodate these systems into the fabric of building components. However, extremely few products and/or innovative solutions for doing such seem to be provided by the industry. We seem incompetent with solutions that are not costing the Earth, insulating, lightweight, and offering an instant response time to con... [more]

Geothermal power plants have become the main application that utilizes geothermal energy. The utilization of deep geothermal energy adheres great importance to the soil condition. One of the biggest challenges faced by geothermal power plant designers is to reduce the risk of soil exploration. To solve this problem, forecasting by modeling has proven to be an important tool to address the problem. In this research, a geo-model was established by modeling three geological layers with different hydraulic and thermal properties to solve the above dilemma. The layers, elevation, and fault zones were simulated using interpolation functions from an artificial dataset. The coupled porous media flow and heat transfer problem using Darcy’s law, as well as heat transfer in porous media interfaces, were studied. The evolution of the flow field, hydrothermal performance, and temperature gradient were also analyzed for a period of 10 years. The results showed the recoverable thermal energy area gra... [more]

The catalytic combustion has the advantage of lower auto-ignition temperature and helps to expand the combustible limit of lean premixed gas. However, the intake needs to be preheated to certain temperature commonly through an independent heat exchanger. Similar to the principles of non-catalytic RTO combustion, this paper presents a similar approach whereby the combustion chamber is replaced by a catalytic combustion bed. A new catalytic reactor integrated with a heat recuperator is designed to enhance the heat recirculation effect. Using a two-dimensional computational fluid dynamics model, the performance of the reactor is studied. The reaction performances of the traditional and compact reactors are compared and analyzed. Under the same conditions, the compact reactor has better reaction performance and heat recirculation effect, which can effectively decrease the ignition temperature of feed gas. The influences of the inlet velocity, the inlet temperature, the methane concentratio... [more]

The homogeneous oxidation of elemental mercury (Hg0) can promote Hg pollution control in coal-fired power plants, while the mechanisms and quantitative contributions of homogeneous reactions in Hg0 oxidation, especially the reactions between Hg and chlorine (Cl), are still unclear. Here, a numerical study on the homogeneous reactions of Hg was conducted within a 600 MW tangentially fired boiler for the first time. A novel Hg sub-model was established by coupling the thermodynamics, reaction kinetics and fluid dynamics. The results showed that the higher Cl content in coal was beneficial to the oxidation of Hg0. The homogeneous reactions of Hg mainly occurred in the vertical flue pass at low temperature. Hg0 was still the dominant Hg-containing species at the boiler exit, and the concentration of mercury chloride (HgCl2) was the highest among the oxidized mercury. When low-Cl coal was fired, the addition of a small amount of chlorine species into the boiler at the burnout area increased... [more]

Microbial fuel cells (MFC) are an emerging technology for wastewater treatment that utilizes the metabolism of microorganisms to generate electricity from the organic matter present in water directly. The principle of MFC is the same as hydrogen fuel cell and has three main components (i.e., anode, cathode, and proton exchange membrane). The membrane separates the anode and cathode chambers and keeps the anaerobic and aerobic conditions in the two chambers, respectively. This review paper describes the state-of-the-art membrane materials particularly suited for MFC and discusses the recent development to obtain robust, sustainable, and cost-effective membranes. Nafion 117, Flemion, and Hyflon are the typical commercially available membranes used in MFC. Use of non-fluorinated polymeric membrane materials such as sulfonated silicon dioxide (S-SiO2) in sulfonated polystyrene ethylene butylene polystyrene (SSEBS), sulfonated polyether ether ketone (SPEEK) and graphene oxide sulfonated pol... [more]

Two years of high-resolution simulations conducted with the Weather Research and Forecasting (WRF) model are used to characterize the frequency, intensity and height of low-level jets (LLJ) over the U.S. Atlantic coastal zone. Meteorological conditions and the occurrence and characteristics of LLJs are described for (i) the centroids of thirteen of the sixteen active offshore wind energy lease areas off the U.S. east coast and (ii) along two transects extending east from the U.S. coastline across the northern lease areas (LA). Flow close to the nominal hub-height of wind turbines is predominantly northwesterly and southwesterly and exhibits pronounced seasonality, with highest wind speeds in November, and lowest wind speeds in June. LLJs diagnosed using vertical profiles of modeled wind speeds from approximately 20 to 530 m above sea level exhibit highest frequency in LA south of Massachusetts, where LLJs are identified in up to 12% of hours in June. LLJs are considerably less frequent... [more]

This paper proposes a novel virtual inertia control (VIC) method based on a feedforward decoupling strategy to address the low inertia issue of power-converter-interfaced microgrids. The feedforward control scheme is employed to eliminate the coupling between active and reactive power caused by line impedance. The active power-voltage droop can be applied to the battery converter in the hybrid energy storage system (HESS). A novel VIC method is developed for the supercapacitor (SC) converter of HESS to increase the inertia of the microgrid. Detailed small-signal modeling of the SC converter with the proposed VIC was conducted, and the transfer function model was obtained. Parameter analysis of the virtual inertia and virtual damping was carried out with the pole-zero map method, and the step response characteristic of output voltage amplitude with power variation was analyzed in detail, deriving the parameter design principle. The simulation study verifies the effectiveness and validit... [more]

The paper presents the results of an analysis of the impact of activities related to the implementation of Poland’s climate policy on the level of demand for hard coal. The authors used sets of indicators built by Eurostat during the analysis. The analysis was based on a set of indicators that had not previously been used for this purpose. The applied ARAMAX model made it possible to study the impact of the presented indicators on the volume of demand for hard coal in Poland. They were introduced to the ARMAX model as explanatory variables. The demand for hard coal in Poland was the dependent variable. The set of indicators was verified, and finally only statistically significant factors were used to build the model. The forecast of the demand for hard coal was made until 2022. It showed that the volume of coal sales would systematically fall as long as factors affecting demand remain constant. However, an additional factor was taken into account in the analysis, namely the increase in... [more]

Automation and electrification are changing vehicles and mobility. Whereas electrification is mainly changing the powertrain, automation enables the rethinking of the vehicle and its applications. The actual driving range is an important requirement for the design of automated and electric vehicles, especially if they are part of a fleet. To size the battery accordingly, not only the consumption of the powertrain has to be estimated, but also that of the auxiliary users. Heating Ventilation and Air Conditioning (HVAC) is one of the biggest auxiliary consumers. Thus, a variable HVAC model for vehicles with electric powertrain was developed to estimate the consumption depending on vehicle size and weather scenario. After integrating the model into a tool for autonomous and electric vehicle concept development, various vehicle concepts were simulated in different weather scenarios and driving cycles with the HVAC consumption considered for battery sizing. The results indicate that the bat... [more]

Internet of Things (IoT) provides large-scale solutions for efficient resource monitoring and management. As such, the technology has been heavily integrated into domains such as manufacturing, healthcare, agriculture, and utilities, which led to the emergence of sustainable smart cities. The success of smart cities depends on the availability of data, as well as the quality of the data management infrastructure. IoT introduced numerous new software, hardware, and networking technologies designed for efficient and low-cost data transport, storage, and processing. However, proper selection and integration of the correct technologies is crucial to ensuring a positive return on investment for such systems. This paper presents a novel end-to-end infrastructure for solar energy analysis and prediction via edge-based analytics.

This paper presents changes in the flow of 14 rivers located in the Warta River basin, recorded from 1951 to 2020. The Warta is the third-longest river in Poland. Unfortunately, the Warta River catchment area is one of the most water-scarce regions. It hosts about 150 hydropower plants with a capacity of up to 5 kW. The catchment areas of the 14 smaller rivers selected for the study differ in location, size, land cover structure and geological structure. The paper is the first study of this type with respect to both the number of analyzed catchments, the length of the sampling series and the number of analyzed flow characteristics in this part of Europe. The analysis of changes in the river flows was performed with reference to low minimum, mean and maximum monthly, seasonal and annual flows. Particular attention was paid to 1, 3, 7, 30 and 90-day low flows and durations of the flows between Q50 and Q90%. In addition, the duration of flows between Q50 and Q90% were analysed. Analysis o... [more]

The thermal efficiency of an efficient gasoline engine is only about 40% and it will produce a large number of harmful products. Curbing harmful emissions and enhancing thermal efficiency have always been the goals pursued and emission regulations are also being tightened gradually. As one of the main consumers of fossil fuels, automobile engines must further reduce fuel consumption and emissions to comply with the concept of low-carbon development, which will also help them compete with electric vehicles. Homogeneous charge compression ignition (HCCI) combustion combined with variable valve actuation (VVA) technology is one of the important ways to improve engine emissions and economy. HCCI combustion based on VVA can only be realized at small and medium loads. The actual application on the entire vehicle needs to be combined with spark ignition (SI) combustion to achieve full working condition coverage. Therefore, HCCI combustion needs fast valve response characteristics; however, th... [more]

Power electronic circuits in modern power supplies have improved the conversion efficiency on the one hand but have also increased harmonic emissions. Harmonic currents from the operation of these units affect the voltage waveforms of the network and could compromise the reliability of the network. Load and source non-linearity can, therefore, limit the renewable source’s hosting capacity in the grid, as a large number of inverter units may increase the harmonic distortions. As a result, voltage and current distortions could reach unbearable levels in devices connected to the network. Harmonic estimation modelling often relies on measurement data, and differences may appear in mathematical simulations as the harmonic aggregation or cancellation may generate different results due to the inaccuracies and limitations of the measurement device. In this paper, the effect of harmonic currents cancellation on the aggregation of different load currents is evaluated to show its impact in the ne... [more]

Energy transition is a multi-dimensional process of developing sustainable economies by seeking renewable energy sources, saving energy, and improving energy efficiency. This process follows the rules of sustainable development. The article presents an analysis of energy transition in the Baltic Sea Region (BSR) enjoying long-term and intensive territorial cooperation. The region embraces 11 countries diversified in terms of their economic development level and the use of renewable energy sources. The article strives to answer the question of whether territorial cooperation contributes to BSR energy transition, and if so, in what way. Another goal is to identify the transition drivers that arise from the Baltic Sea Region’s unique characteristics. The authors applied the system analysis methodology. The performed literature studies allowed the researchers to identify the attributes of energy transition. Empirical research relied on secondary sources, including the European Union (EU) s... [more]

Nano/microrobots (NMRs) are tiny devices that can convert energy into motion and operate at nano/microscales.54 Especially in biomedical research, NMRs have received much attention over the past twenty years because of their excellent capabilities and great potential in various applications, including on-demand drug delivery, gene and cell transport, and precise microsurgery. Reports published in recent years show that synthetic nano/microrobots have promising potential to function in the gastrointestinal (GI) region, particularly in terms of drug delivery. These tiny robots were able to be designed in such a way that they propel in their surroundings (biological media) with high speed, load cargo (drug) efficiently, transport it safely, and release upon request successfully. Their propulsion, retention, distribution, and toxicity in the GI tract of mice has been evaluated. The results envisage that such nano/microrobots can be further modified and developed as a new-generation treatme... [more]