Recently, the use of diverse renewable energy resources has been intensively expanding due to their technical and environmental benefits. One of the important issues in the modeling and simulation of renewable energy resources is the extraction of the unknown parameters in photovoltaic models. In this regard, the parameters of three models of photovoltaic (PV) cells are extracted in this paper with a new optimization method called turbulent flow of water-based optimization (TFWO). The applications of the proposed TFWO algorithm for extracting the optimal values of the parameters for various PV models are implemented on the real data of a 55 mm diameter commercial R.T.C. France solar cell and experimental data of a KC200GT module. Further, an assessment study is employed to show the capability of the proposed TFWO algorithm compared with several recent optimization techniques such as the marine predators algorithm (MPA), equilibrium optimization (EO), and manta ray foraging optimization... [more]

A new algorithm, Material Generation Algorithm (MGA), was developed and applied for the optimum design of engineering problems. Some advanced and basic aspects of material chemistry, specifically the configuration of chemical compounds and chemical reactions in producing new materials, are determined as inspirational concepts of the MGA. For numerical investigations purposes, 10 constrained optimization problems in different dimensions of 10, 30, 50, and 100, which have been benchmarked by the Competitions on Evolutionary Computation (CEC), are selected as test examples while 15 of the well-known engineering design problems are also determined to evaluate the overall performance of the proposed method. The best results of different classical and new metaheuristic optimization algorithms in dealing with the selected problems were taken from the recent literature for comparison with MGA. Additionally, the statistical values of the MGA algorithm, consisting of the mean, worst, and standar... [more]

The aim of this paper is to perform optimization of photopolymerization process of dental composites in order to obtain maximum hardness. Samples (5 mm diameter; 2, 3 and 4 mm thickness) were made of Universal Composite (UC), Bulk fill Composite (BC) and Flowable Composite (FC). Light curing of specimens was performed with 600, 1000 and 1500 mW/cm2 light intensity and an irradiation time of 20, 40 and 60 s. Vickers microhardness on the top and bottom surfaces of samples was measured. Optimization was carried out via regression analysis using QStatLab software. Photopolymerization process parameters were calculated using a specially designed MatLab software-based algorithm. For all composites, regression models for hardness on top and bottom surfaces of composite layer were established. Layer thickness as well as hardness on top and bottom surfaces of each composite was calculated for 21 curing modes varying with light intensity and irradiation time. It was established that photopolymer... [more]

The quality of product and process is one of the most important factors in achieving constructively and then functionally safe products in any industry. Over the years, the concept of Industry 4.0 has emerged in all the quality processes, such as nondestructive testing (NDT). The most widely used quality control methods in the industries of mechanical engineering, aerospace, and civil engineering are nondestructive methods, which are based on inspection by detecting indications, without affecting the surface quality of the examined parts. Over time, the focus has been on research with the fourth generation in nondestructive testing, i.e., NDT 4.0 or Smart NDT, as a main topic to ensure the efficiency and effectiveness of the methods for a safe detection of all types of discontinuities. This area of research aims at the efficiency of methods, the elimination of human errors, digitalization, and optimization from a constructive point of view. In this paper, we presented a magnetic partic... [more]

Development of paper industry has been restricted by resources, energy and environment deeply; further reducing energy consumption becomes an urgent problem to be solved. In this paper, the calculating model of steam consumption in bleaching process is established under the premise of ensuring product quality and controlling bleaching cost. Then, an optimization model for minimizing steam consumption is constructed. Compared with before optimization, the steam consumption of the optimized bleaching system reduced by 19.48% (0.5014 t/adt) at a loss of 0.11% brightness (0.1 ISO%) and 5.17% viscosity (33 mL/g). The amount of chemicals should be increased to ensure the quality of the pulp while decreasing the bleaching temperature to reduce steam consumption, the cost of bleaching pulp has decreased by 1.62% (3.19 USD/adt) after optimization. The verification experiments showed all the pulp quality indices can meet the requirements of bleached pulp.

This paper reviews actual sustainability assessments in the construction sector to define whether and how a Life Cycle Sustainability Assessment (LCSA) is applied and interpreted in this sector today. This industry has large shares in global energy (33%), raw material consumption (40%) and solid waste generation (40%). Simultaneously, it drives the economy and provides jobs. The LCSA is a method to identify environmental, social and economic impacts of products/services along their life cycles. The results of this study showed a mismatch between sectoral emissions and the number of LCSA-based impact evaluations. It was found that only 11% of papers reviewed assessed all three sustainability pillars. The economic and especially the social pillars were partly neglected. In Life Cycle Assessments (LCAs), 100% made use of Global Warming Potential (GWP) but only 30% assessed more than five indicators in total. In Life Cycle Costing (LCC), there were a variety of costs assessed. Depreciation... [more]

Due to the numerous side effects of synthetic pesticides, including environmental pollution, threats to human health, harmful effects on non-target organisms and pest resistance, the use of alternative healthy, available and efficient agents in pest management strategies is necessary. In this paper, the susceptibility of the cosmopolitan, polyphagous, stored-product pest Tribolium castaneum (red flour beetle) to the fumigation of the essential oils of two important medicinal and food additive plants, Satureja hortensis and S. intermedia, was investigated. The insecticidal properties of the essential oils were modeled and optimized using response surface methodology. It was found that a maximum significant mortality of 94.72% and 92.97% could be achieved within 72 h with the applications of 55.15 µL/L of S. hortensis (with the linear model) and 58.82 µL/L of S. intermedia (with the quadratic model), respectively. There were insecticidal terpenes and phenylpropanoids in both essential oi... [more]

This paper presents a study of the use of flow baffles inside a centrifugal air classifier. An air classifier belongs to the most widely used classification devices in mills in the mineral industry, which is why there is a great interest in optimizing the process flow and pressure loss. Using Computational Fluid Dynamics (CFD), the flow profile in a classifier without and with flow baffles is systematically compared. In the simulations, turbulence effects are modeled with the realizable k−ε model, and the Multiple Reference Frame approach (MRF) is used to represent the rotation of the classifier wheel. The discrete phase model is used to predict the collection efficiency. The effects on the pressure loss and the classification efficiency of the classifier are considered for two operating conditions. In addition, a comparison with experimental data is performed. Firstly, the simulations and experiments show good agreement. Furthermore, the investigations show that the use of flow baffle... [more]

In the last decade, simulation software as a tool for managing and controlling business processes has received a lot of attention. Many of the new software features allow businesses to achieve better quality results using optimisation, such as genetic algorithms. This article describes the use of modelling and simulation in shipment and sorting processes that are optimised by a genetic algorithm’s involvement. The designed algorithm and simulation model focuses on optimising the duration of shipment processing times and numbers of workers. The commercially available software Tecnomatix Plant Simulation, paired with a genetic algorithm, was used for optimisation, decreasing time durations, and thus selecting the most suitable solution for defined inputs. This method has produced better results in comparison to the classical heuristic methods and, furthermore, is not as time consuming. This article, at its core, describes the algorithm used to determine the optimal number of workers in s... [more]

Dividing-wall columns (DWCs) are intensified processes that have attracted industrial and academic attention due to the reduction in operating and installation costs compared to traditional distillation systems. Several methodologies are available for the design of DWCs. Most of them consist of three parts: an analysis of operating variables; an analysis of the structural design (topology); and an optimization of the resulting preliminary design. This paper aims to study three widely used design methodologies reported in the literature for DWCs, i.e., Triantafyllou and Smith (T&S), minimum vapor (Vmin), and Sotudeh and Shahraki (S&S) methods, along with their implementation on process simulators. A proposed modification to the S&S methodology is also presented. A comparison of the methods is carried out and rated against designs with minimum total annual costs. The analysis considers the effect of different structural design variables to initialize the design procedure with each method... [more]

This study highlights an innovative piece of hybrid technology, whereby the combination of anaerobic and aerobic processes into a single reactor, namely, the integrated anaerobic−aerobic bioreactor (IAAB) can surpass the limits of conventional methods treating palm oil mill effluent (POME). Optimisation of IAAB using SuperPro Designer V9 simulator for maximum biogas yield while addressing its economic and environmental trade-offs was conducted for the first time. Parameters such as hydraulic retention time (HRT) and organic loading rate (OLR) were optimised in the anaerobic compartment from 10 days and 6.2 g COD/L day to 9 days and 6.9 g COD/L day, respectively. Furthermore, sludge recycle ratio was optimised from 20% to 50% in the aerobic compartment. The optimisation was successful where the biogas yield increased from 0.24 to 0.29 L CH4/g CODremoved with excellent Chemical Oxygen Demand (COD), and Biological Oxygen Demand (BOD) removal efficiencies up to 99% with 5.8% lower net expe... [more]

Solid Oxide Fuel Cell (SOFC) technology is of high interest for stationary decentralized generation of electricity and heat in combined heat and power systems (CHP) for the residential sector. Application scenarios for SOFC systems in an electricity-regulated mode play an important role, especially in places where an electrical grid connection is not available or rather unstable. The advantages of SOFC systems are the high fuel flexibility and the high efficiencies also under partial load operation compared to other decentralized power generation technologies. Due to the long, energy-consuming system heat-up and the limited partial load capability, SOFC systems do not reach the performance of conventional power generation technologies. Furthermore, stack thermal cycling is associated with power degradation and should be minimized. In this paper, the improvement of these drawbacks are investigated for hotbox-based SOFC systems in the 1 kWel-class for residential applications. Since expe... [more]

The aim of the study was to estimate the optimal parameters of apple drying and the rehydration temperature of the obtained dried apple. Conducting both processes under such conditions is aimed at restoring the rehydrated apple to the raw material properties. The obtained drying parameters allow the drying process to be carried out in a short drying time (DT) and at low energy consumption (EC). The effect of air velocity (vd), drying temperature (Td), characteristic dimension (CD), and rehydration temperature (Tr) on rehydrated apple quality was studied. Quality parameters of the rehydrated apple as: color change (CC), mass gain ratio (MG), solid loss ratio (SL), volume gain ratio (VG) together with DT and EC were taken into consideration. The artificial neural network was used for modeling of rehydrated apple quality parameters, DT, and EC. A multi-objective genetic algorithm was developed in order to optimize parameters of the drying and rehydration processes. The simultaneous minimi... [more]

To improve the transport performance of a rotodynamic multiphase pump for a gas−liquid mixture, we took the head and efficiency index at rated flow rate with 15% inlet gas volume fraction as the indices, and used the orthogonal test design method and CFD technology to optimize. We selected the blade shroud angles at the leading edge and trailing edge, and axial length of the impeller, as well as the inlet incidence angle and blade number of the diffuser, and a total of five factors were used for the orthogonal test. The weight function was used to determine the final trial protocol. The results showed that the blade shroud angle at the trailing edge had the greatest influence on the head and efficiency indices. Under the rated flow rate with a 15% inlet gas volume fraction, the head and efficiency of the optimized pump were increased by 2.81 m and 5.6%, respectively, in comparison to the base pump. After the optimization, the partial fast-speed regions at the inlet of the impeller pass... [more]

In this study, the response surface methodology (RSM) optimization technique was employed for investigating the impact of hydroxy gas (HHO) enriched diesel on performance, acoustics, smoke and exhaust gas emissions of the compression ignition (CI) engine. The engine was operated within the HHO flow rate range of 0−10 L/min and engine loads of 15%, 30%, 45%, 60% and 75%. The results disclosed that HHO concentration and engine load had a substantial influence on the response variables. Analysis of variance (ANOVA) results of developed quadratic models indicated the appropriate fit for all models. Moreover, the optimization of the user-defined historical design of an experiment identified an optimum HHO flow rate of 8 L/min and 41% engine load, with composite desirability of 0.733. The responses corresponding to optimal study factors were 25.44%, 0.315 kg/kWh, 117.73 ppm, 140.87 ppm, 99.37 dB, and 1.97% for brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), CO, HC, no... [more]

Biodiesel is a promising renewable energy option that significantly reduces the emission of greenhouse gases and other toxic byproducts. However, a major challenge in the industrial scale production of biodiesel is the desired product purity. To this end, reactive distillation (RD) processes, which involve simultaneous removal of the byproduct during the transesterification reaction, can drive the equilibrium towards high product yield. In the present study, we first optimized the heat exchange network (HEN) for a high purity RD process leading to a 34% reduction in the overall energy consumption. Further, a robust control scheme is proposed to mitigate any feed disturbance in the process that may compromise the product purity. Three rigorous case studies are performed to investigate the effect of composition control in the cascade with the temperature control of the product composition. The cascade control scheme effectively countered the disturbances and maintained the fatty acid mon... [more]

Friction materials, mainly made of reinforced composites, should possess excellent physical and tribological properties, such as a higher coefficient of friction, minimum wear, adequate surface hardness, and higher porosity for various automotive brake applications. Attainment of those properties greatly depends on the settings of different input parameters, such as molding pressure, temperature and time, temperature and time of heat treatment/sintering, etc., during the processing of friction materials. In this article, four multi-criteria decision-making (MCDM) tools, i.e., technique for order of preference by similarity to ideal solution (TOPSIS), evaluation based on distance from average solution (EDAS), VlseKriterijumska Optimizacija I Kompromisno Resenje (VIKOR), and multi-objective optimization on the basis of ratio analysis (MOORA) are applied to identify the optimal parametric combinations for two different friction materials. A comparative analysis of the derived results sugg... [more]

Process-based numerical models developed to perform hydraulic/hydrologic/water quality analysis of watersheds and rivers have become highly sophisticated, with a corresponding increase in their computation time. However, for incidents such as water pollution, rapid analysis and decision-making are critical. This paper proposes an optimized parallelization scheme to reduce the computation time of the Environmental Fluid Dynamics Code-National Institute of Environmental Research (EFDC-NIER) model, which has been continuously developed for water pollution or algal bloom prediction in rivers. An existing source code and a parallel computational code with open multi-processing (OpenMP) and a message passing interface (MPI) were optimized, and their computation times compared. Subsequently, the simulation results for the existing EFDC model and the model with the parallel computation code were compared. Furthermore, the optimal parallel combination for hybrid parallel computation was evaluat... [more]

The friction rotary welding (FRW) of magnesium alloy to aluminum alloy was presented in a paper due to significant interest in the manufacturing industry. A genetic algorithm (GA) method for optimizing FRW process parameters of dissimilar light alloys was presented. After obtaining the welding parameters by GA method, it was possible to determine the best tensile strength of the friction joint. The obtained joints were subjected to tensile strength. The highest tensile strength TS = 178 MPa was found using a genetic algorithm for the following friction welding parameters: friction force FF = 16 kN, friction time FT = 4 s, and upsetting force UF = 44 kN. The optimized values were compared with the experimental results. The application of the genetic algorithm method allowed increasing the tensile strength joint from 88 to 180 MPa. The maximum tensile strength of the friction welded magnesium alloy-aluminum alloy joints was 73% of the base AZ31B metal. The relationship between welding pa... [more]

Applications of dual-evaporator refrigeration systems have recently gained much attention both in academia and industry due to their multiple benefits. In this study, a comprehensive thermodynamic and economic analysis is conducted to evaluate the potential of using several environmentally friendly refrigerant couples and identifies the most suitable one yielding the best economic results. To achieve this goal, a detailed parametric study is conducted, and an optimization process is performed using a particle swarm optimization (PSO) approach to minimize the unit production cost of cooling (UPCC) of the cascade refrigeration system. The results showed that among all selected 18 refrigerant pairs and for all ranges of examined operating parameters, the R170-R161 pair and R1150-R1234yf pair are identified as the best and worst pairs, respectively, from both thermodynamic and economic viewpoints. The results also confirm that R170-R161 pair has an improvement over R717-R744, used as a typ... [more]

This paper presents the application of Taguchi design of experiment and Autodesk Moldflow® simulation in finding the optimal processing parameters for the manufacturing of natural fiber−polymer composite products. The material used in the study is a composite of recycled thermoplastic reinforced with 10% wood fibers. For the study, four critical processing parameters, namely compression time, mold temperature, melt temperate, and pressure, were selected for optimization. Process analysis was carried out in Moldflow® utilizing a combination of process parameters based on an L9 orthogonal array. Later, the warpage output from Moldflow® simulation was converted into a signal-to-noise (S/N) ratio response, and the optimum values of each processing parameter were obtained using the smaller-the-better quality characteristic. The results show that the optimum values were 60 °C, 40 s, 210 °C, and 600 kN for the mold temperature, compression time, melt temperature, and pressure, respectively. A... [more]

As the carbon emissions of commercial buildings are attracting considerable attention, the integrated energy system (IES) has become a promising low-carbon method in response. In this paper, an optimization framework for low-carbon oriented integrated energy system management under electric vehicles (EV) demand response is proposed. After analyzing the charging behavior, EV charging demand is simulated. Then, the low-carbon integrated energy system model is proposed with the optimization framework considering carbon reduction. Subsequently the objective function containing carbon emission is obtained for the whole operation optimization. The results of the studied case show that the optimization framework proposed can reduce the carbon emission greatly as well as moderate economic cost, which declined because of the revenue from charging demand response. In general, the optimization of low-carbon oriented IES in commercial buildings is feasible.

In order to attain high manufacturing productivity, industry 4.0 merges all the available system and environment data that can empower the enabled-intelligent techniques. The use of data provokes the manufacturing self-awareness, reconfiguring the traditional manufacturing challenges. The current piece of research renders attention to new consideration in the Job Shop Scheduling (JSSP) based problems as a case study. In that field, a great number of previous research papers provided optimization solutions for JSSP, relying on heuristics based algorithms. The current study investigates the main elements of such algorithms to provide a concise anatomy and a review on the previous research papers. Going through the study, a new optimization scope is introduced relying on additional available data of a machine, by which the Flexible Job-Shop Scheduling Problem (FJSP) is converted to a dynamic machine state assignation problem. Deploying two-stages, the study utilizes a combination of discr... [more]

It has become increasingly popular to replace chemically synthesized compounds with natural counterparts mostly found in natural sources, such as natural pigments. The conventional extraction processes for these compounds are limited by the toxicity and flammability of the solvents. To obtain pure extracts, it is always a longer process that requires several steps. Supercritical fluid extraction (SFE) is a cutting-edge green technology that is continuously increasing and expanding its fields of application, with benefits such as no waste produced, shorter extraction time, automation, and lower solvent consumption. The SFE of natural pigments has high potential in food, textiles, cosmetics, and pharmaceuticals; there are a number of other applications that can benefit from the SFE technique of natural pigments. The pigments that are extracted via SFE have a high potential for application and sustainability because of their biological and antimicrobial properties as well as low environme... [more]

Most spoilers are made from a sandwich structure with a honeycomb component as its core. However, the honeycomb core is sensitive to water ingress, causing damage to the control surface due to its weak moisture-resistance behavior. This study aimed to conduct the design and analysis of an improved composite structure for a coreless spoiler. A spoiler design of an aircraft, the A320, was used for the case study. The weaknesses of a coreless spoiler were identified through finite element analysis via Abaqus software. Multi-spar and multi-rib designs were studied and compared for topological optimization. The variables used for evaluation were the Tsai−Hill failure index and the critical buckling load. The design with the most potential was considered for parametric optimization to obtain the most satisfactory configuration. The results showed that the upper skin of the spoiler without a honeycomb core failed the Tsai−Hill criteria. Furthermore, the results show that the multi-spar config... [more]