Pre-treatments at relatively high temperatures (range 160 °C−220 °C) are currently used to transform lignocellulosics into biofuels and chemicals. In this step, several molecules with an inhibitory effect in the subsequent fermentation processes are generated. These inhibitors include low-molecular-weight molecules and lignin fragments that can be removed by water washing. However, this procedure also removes valuable soluble carbohydrates which are then difficult to recover from the diluted stream. In this work, a new method to detoxify steam-exploded substrates is reported. The procedure is based on the evaporation of low-weight acids and aldehydes, which leaves all the sugars in the solid matrix, while the cellulose hornification (an irreversible modification of the cellulose fibres that depresses the saccharification yield) is prevented by adding steam to the hot fluidizing flow stream. Two systems were tested: a 0.1 kg/batch oscillating fluidized bed and a continuous fluidized bed... [more]

The objective of this study was to synthesize different polyphenol−corn starch complexes including gallic acid−starch and quercetin−starch by conjugating corn starch with gallic acid and quercetin using the free radical grafting method. This process was effective in enhancing conjugations of starch molecules with gallic acid and quercetin (5.20 and 5.83 mg GAE/g, respectively) and imparted promising antioxidant capacity to the phenolic−starch complexes. Significant interactions between these phenolic compounds and corn starch molecules were revealed with an ultraperformance liquid chromatography electrospray ionization Q-time-of-flight mass spectrometry assay. It was revealed that significantly higher levels of resistant starch in the above gallic−starch and quercetin−starch complex samples (11.6 and 15.3 g/100 g, respectively) together with an obvious reduction in glycemic response (7.9% and 11.8%, respectively) observed over the control. Complex samples functionalized with gallic aci... [more]

Exergy analysis and advanced exergy analysis of an absorption chiller/Kalina cycle integrated system are conducted in this research. The exergy destruction of each component and overall exergy efficiency of the cascade process have been obtained. Advanced exergy analysis investigates the interactions among different components and the actual improvement potential. Results show that among all the equipment, the largest exergy destruction is in the generators and absorber. System exergy efficiency is obtained as 35.52%. Advanced analysis results show that the endogenous exergy destruction is dominant in each component. Interconnections among different components are not significant but very complicated. It is suggested that the improvement priority should be given to the turbine. Performance improvement of this low-grade waste heat recovery process is still necessary because around 1/4 of the total exergy destruction can be avoided. Exergy and advanced exergy analysis in this work locate... [more]

Oxidation-reduction potential (ORP) sensors would constitute a robust surveillance and control solution for aeration and external carbon dosing in wastewater biological treatment processes if a clear correlation exists between the ORP values and process variables (e.g., dissolved oxygen (DO), nitrate, and chemical oxygen demand (COD). In this study, ORP values and other water quality variables were analyzed, and principal component analysis (PCA) and analysis of variance were used to study the relationships between ORP and main reactive substances under anoxic conditions. Mathematical models were then established using multiple regression analysis. The results showed that under anoxic conditions, ORP was positively correlated with nitrate, DO, and COD and negatively correlated with ammonia nitrogen, phosphate, and pH. COD had a low correlation with the ORP value change. PCA showed that the mathematical model of ORP can be established by using DO, nitrate, and phosphate, for which the a... [more]

Texture and coating technology can significantly improve the tribological properties of mechanical components. In this study, the lubricating and wear properties of the reticular surface texture under the action of TiN were studied. Lubrication and wear experiments at different speeds were conducted using a UMT-3 wear and friction testing machine. Using Fluent fluid simulation, the bearing capacity of the oil film was obtained, and the lubrication performance of the texture was verified. The results showed that the simulation experiment and the lubrication experiment were consistent to a certain extent. For the groove width and angle parameters studied in this paper, optimal parameters existed to achieve the maximum bearing capacity, 1.27 N. Due to the high hardness and low elastic modulus of the TiN coating, the coated reticular texture was more wear-resistant, and it achieved the minimum wear volume 1.148 × 10−6 mm3 from the grinding stainless-steel matrix. The effect of the fluid dy... [more]

Recently, a new swarm intelligence optimization algorithm called the remora optimization algorithm (ROA) was proposed. ROA simulates the remora’s behavior of the adsorption host and uses some formulas of the sailfish optimization (SFO) algorithm and whale optimization algorithm (WOA) to update the solutions. However, the performance of ROA is still unsatisfactory. When solving complex problems, ROA’s convergence ability requires further improvement. Moreover, it is easy to fall into local optimization. Since the remora depends on the host to obtain food and optimize ROA performance, this paper introduces the mutualistic strategy to strengthen the symbiotic relationship between the remora and the host. Meanwhile, chaotic tent mapping and roulette wheel selection are added to further improve the algorithm’s performance. By incorporating the above improvements, this paper proposes an improved remora optimization algorithm with a mutualistic strategy (IROA) and uses 23 benchmark functions... [more]

Highly heterogeneous glutenite reservoirs with large amounts of gravel and weak interfaces pose a great challenge to predicting the trajectory of hydraulic fractures during the fracturing process. Based on the phase field method, a fully coupled numerical model of hydraulic fracturing is established. This paper is devoted to investigating the variation in the overall expansion pattern of hydraulic fractures in reservoirs considering randomly distributed gravel and weak interfaces. The numerical results demonstrate that the existence of gravel and a weak interface could alter the extending paths of the hydraulic fractures as well as the value of critical bifurcation injection rate. As the fracture energy of the weak interface is large enough, the hydraulic fracture tends to cross the gravel and the weak interface between the rock matrix and the gravel, forming a planar fracture. Deflection and branching of the hydraulic fracture are more likely to occur in reservoirs containing large gr... [more]

The physical meaning and calculating process of the rheological parameters of two nonlinear rheological models, the parabolic model and the modified Bingham model, were compared. The fluidity test and a rheological experiment on cementitious materials were performed. The Couette inverse problem is a key issue in measuring and solving the rheological parameters of fresh cementitious materials. The solution of the Couette inverse problem based on the modified Bingham model is discontinuous when the coefficient of the quadratic term is equal to zero, resulting in a large deviation between the fitting curve and the rheological experimental data. The credibility of the rheological parameters of the pastes calculated based on the modified Bingham model is low. The formulas for calculating yield stress, fiducial differential viscosity and the degree of shear thickening or shear thinning of the parabolic model have been developed. The credibility of the rheological parameters of the pastes cal... [more]

Shale gas reservoirs are one of the most rapidly growing forms of natural gas worldwide. Gas production from such reservoirs is possible by using extensive and deep well fracturing to contact bulky fractions of the shale formation. In addition, the main mechanisms of the shale gas production process are the gas desorption that takes place by diffusion of gas in the shale matrix and by Darcy’s type through the fractures. This study presents a finite element model to simulate the gas flow including desorption and diffusion in shale gas reservoirs. A finite element model is used incorporated with a quadrilateral element mesh for gas pressure solution. In the presented model, the absorbed gas content is described by Langmuir’s isotherm equation. The non-linear iterative method is incorporated with the finite element technique to solve for gas property changes and pressure distribution. The model is verified against an analytical solution for methane depletion and the results show the robus... [more]

The concept of the metaverse has gained increasing attention in recent years, and the development of various new technologies, including digital twin technology, has made it possible to see the metaverse coming to pass. Many academics have begun to investigate various problems after realizing the importance of digital twin technology in building the metaverse. However, when utilizing digital twin technology to construct a metaverse, there remains limited research on how to allocate multibase station resources. This research translates a multibase station wireless resource allocation problem into an integer linear programming constraint model when virtual service providers construct a metaverse. In addition, the optimal VCG reverse auction (OPT-VCGRA) mechanism is designed to maximize social welfare and solve the problem of IoT devices competing for base station wireless resources. Specifically, the problem of the optimal allocation of wireless channel resources and payment rule based o... [more]

In an actual thermal power plant, deep peak shaving will cause thermal power units to run under non-nominal conditions for an extended period, resulting in serious problems such as increased equipment wearing, low equipment utilization efficiency and decreased benefits. To this end, in this work, both the design and optimization method for a coal to hydrogen system which is coupled with the expected non-nominal operation of thermal power units are proposed. Aiming towards maximum profit in the context of thermal power plants, a mathematical optimization model for a coal to hydrogen system based on the multi-period operating conditions of thermal power plants is established. The corresponding optimal design scheme of the coal to hydrogen system is determined using variable operating conditions. The superiority of the integrated system compared with an independent system is explored and the feasibility of the proposed method is verified by using the case study of an actual thermal power... [more]

Laser scanning technology has been used for several years. Nevertheless, no comprehensive study has been conducted to prove that the application of confocal chromatic sensor (CCHS) laser technology is effective and suitable to verify the integrity parameters of machined surfaces in terms of cutting tool damage. In this paper, the optimization and effects of five factors (cutting speed, feed, depth of cut, attachment length of the workpiece, and tip radius) on the roundness deviation measured by CCHS and, at the same time, on the amount of wear on the back side of the cutting part of the tool were studied according to ISO 3685, which was measured with a microscope. The results obtained were evaluated using the gray relational analysis method (GRA), in conjunction with the Taguchi method, and the significance of the factors was demonstrated using the analysis of variance (ANOVA) method.

With the development of civilization, the awareness of the impact of versatile aerosol particles on both human health and the environment is growing. New materials are needed to purify the air to control this impact The aspect of processing the produced waste is not negligible. In view of the above, this study proposes utilizing the solution blow spinning process (SBS) for manufacturing a biodegradable filtration structure that ensures high efficiency of nanoobject filtration, with a low pressure drop. Polylactic acid (PLA) was used to produce a nanofiber layer on the coconut substrate. The advantage of this method is the ability to blow fibers with diameters in the nano-scale, applying relatively simple, cost-effective, and easy to scale-up equipment. This work selected appropriate process parameters to produce good quality filters. Moreover, the process conditions influence on the morphology of the obtained structures and, thus, also the filtration properties, were examined. For test... [more]

The advancements in nanotechnology have quickly developed a new subject with vast applications of nanostructured materials in medicine and pharmaceuticals. The enormous surface-to-volume ratio, ease of surface modification, outstanding biocompatibility, and, in the case of mesoporous nanoparticles, the tunable pore size make the silica nanoparticles (SNPs) a promising candidate for nano-based medical applications. The preparation of SNPs and their contemporary usage as drug carriers, contrast agents for imaging, carrier of photosensitizers (PS) in photodynamic, as well as photothermal treatments are intensely discussed in this review. Furthermore, the potential harmful responses of silica nanoparticles are reviewed using data obtained from in vitro and in vivo experiments conducted by several studies. Moreover, we showcase the engineering of SNPs for the theranostic applications that can address several intrinsic limitations of conventional therapeutics and diagnostics. In the end, a p... [more]

In recent years, with the rapid development of equipment manufacturing and advances in the research on mine pressure and rock mechanics, large-mining-height comprehensive mechanized coal mining technology has become increasingly widely used in thick-seam mining. On this basis, because the free space extracted is several times that of layered mining, the occurrence of strong ground pressure caused by the violent movement of the basic roof and the low recovery rate of the top coal have become the main problems. In this study, Dong Liang Coal Mine was taken as the engineering background by which to study the three typical movement forms of the basic roof, and the critical fracture conditions of the three forms were obtained through theoretical calculations. The movement result state of the basic roof strata was taken as the different overlying boundary conditions of the top coal to simulate its impact on the recovery rate, to explore the interaction mechanism between the basic roof strata... [more]

Due to multiple factors influencing the construction safety of TBM hydraulic tunnels, risk assessment is a critical point of a construction management plan to avoid possible risks. In this paper, a safety-risk evaluation index system of TBM construction for hydraulic tunnels is built based on the identification and analysis of possible sources of risk in techniques, geologic, equipment, management, and accidents. Considering the influence of factors such as the experience level and the expertise of decision makers, a combination assignment method of index weights is proposed based on binary semantics. On the basis of a fuzzy normal distribution used as the subordinate function distribution of fuzzy evaluation levels, the subordinate function distribution of fuzzy evaluation levels under multi-level intersection situations is introduced, and a comprehensive evaluation model of safety risks for TBM tunnel construction is built. The validity and practicality of the evaluation model is exa... [more]

L. (St. John’s wort) is one of the most popular medicinal plants in the world. Due to its documented antimicrobial and antioxidant properties, it is used in the treatment of bacterial and viral infections as well as inflammations. It is also used to treat gastrointestinal diseases and mild to moderate depression. In recent years, there has been an increase in the popularity of herbal medicine. Many people collect their own herbs and dry them at home. A common choice for quick drying of fruits, vegetables and herbs at home are food dehydrator machines. There are not many publications in the scientific literature examining the quality of dried herbal material obtained in such dryers. We characterized St. John’s wort harvested in southern Poland and investigated the effect of specific drying methods on the volatile component profile. The herbal raw material was dried using three methods: indoors at room temperature, in an incubator at 37 °C and in a food dehydrator machine. Volatile compo... [more]

It is significant to scientifically identify what factors influence the green growth of manufacturing enterprises and analyze the relationship among these factors, thus promoting green growth. Firstly, the corresponding conceptual model is designed; then, the DEMATEL method and steps used to identify the influencing factors are introduced; finally, the DEMATEL method is adopted to empirically analyze wooden flooring manufacturing companies so as to identify influencing factors of their green growth. According to the results, there are six reason factors, namely environmental standard constraints, green market demand, market competition, green technology advancement, upstream and downstream synergy of green industrial chain, and policy support, which provide the most important external support to enterprises’ green growth and main driving power to wooden flooring manufacturing ones.

Theoretical considerations along with extensive Monte Carlo simulations are used to calculate the lag time before the initiation of diffusion-controlled drug release in multilayer planar devices with an outer layer containing no drug. The presented results are also relevant in formulations coated by a drug-free membrane as well as in other reservoir systems. The diffusion of drug molecules through the outer layer towards the release medium is considered, giving rise to the observed lag time. We have determined the dependence of lag time on the thickness and the diffusion coefficient of the drug-free outer layer, as well as on the initial drug concentration and the surface area of the planar device. A simple expression, obtained through an analytical solution of diffusion equation, provides an approximate estimate for the lag time that describes the numerical results reasonably well; according to this relation, the lag time is proportional to the squared thickness of the outer layer ove... [more]

Modern manufacturing operations always aim toward sustainable production through sustainable operations. Lean Six Sigma manufacturing is one of the leading models to increase operational efficiency and productivity and reduce product manufacturing costs. The lean Six Sigma problem-solving methodology DMAIC has been one of the several techniques organizations use to improve their productivity and the quality of their product and services. This paper aims to apply Lean Six Sigma and DMAIC to enhance production capacity and reduce per-unit cost. Furthermore, this research work has been carried out to analyze the impact of stakeholders on Lean Six Sigma projects. The research follows the DMAIC methodology to investigate and analyze the root cause of the problems and give possible solutions for eliminating or reducing the issues. Particularly, fishbone and 5-Whys techniques were used to determine whether the two key processes, AC Outdoor unit testing with the help of reusable power cords an... [more]

In the past few decades, there has been increasing recognition of the importance of optimum power flow (OPF) studies in the context of economic analyses of power systems. There is a need for power system development to maximize efficiency by emphasizing cost and power losses for smart grids to operate effectively in the current situation. This study aims to develop an optimal capacitor bank allocation schedule that minimizes power losses in the distribution networks under equality constraints. This will be achieved by integrating the loss factor and voltage stability into a new approach to determine where the capacitor banks should be located. It aims to reduce the operating costs of power systems and maximize efficiency by applying an optimization model for economic dispatch, which considers distributed power generation and demand response. The NSGA-II optimization algorithm was used in this study to determine the optimal size and location of the capacitor bank. A NSGA-II solves this... [more]

The estimation of the formation permeability is considered a vital process in assessing reservoir deliverability. The prediction of such a rock property with the use of the minimum number of inputs is mandatory. In general, porosity and permeability are independent rock petrophysical properties. Despite these observations, theoretical relationships have been proposed, such as that by the Kozeny−Carmen theory. This theory, however, treats a highly complex porous medium in a very simple manner. Hence, this study proposes a comprehensive ANN model based on the back propagation learning algorithm using the FORTRAN language to predict the formation permeability from available well logs. The proposed ANN model uses a weight visualization curve technique to optimize the number of hidden neurons and layers. Approximately 500 core data points were collected to generate the model. These data, including gamma ray, sonic travel time, and bulk density, were collected from numerous wells drilled in... [more]

Thermal processing of white radish using retort sterilization at different temperatures was investigated according to the dimension of the package. Four different samples with the same weight and volume were placed in packages with different dimensions. The degree of sterilization (i.e., F0-value) at the cold point targeted at 6 min was determined based on experimental data and heat transfer simulation. The sterilization time was considerably increased with a decrease in surface area to unit volume ratio (φ) at each temperature. The sterilization time for the sample with the highest φ (155.56) was approximately five times faster than the sample with the lowest φ (72.22) at all heating temperatures. Numerical simulation conducted with a proper heat transfer coefficient (h) showed mostly good agreement with the experimental data (RMSE < 2 °C). Changes in color and total phenolic content were higher for samples heated at higher temperatures. Hardness values of white radish samples meas... [more]

Damage to abdominal wall integrity occurs in accidents, infection and herniation. Repairing the hernia remains to be one of the most recurrent common surgical techniques. Supercritical carbon dioxide (SCCO2) was used to decellularize porcine skin to manufacture acellular dermal matrix (ADM) for the reparation of full-thickness abdominal wall defects and hernia. The ADM produced by SCCO2 is chemically equivalent and biocompatible with human skin. The ADM was characterized by hematoxylin and eosin (H&E) staining, 4,6-Diamidino-2-phenylindole, dihydrochloride (DAPI) staining, residual deoxyribonucleic acid (DNA) contents and alpha-galactosidase (α-gal staining), to ensure the complete decellularization of ADM. The ADM mechanical strength was tested following the repair of full-thickness abdominal wall defects (4 × 4 cm) created on the left and right sides in the anterior abdominal wall of New Zealand White rabbits. The ADM produced by SCCO2 technology revealed complete decellularization,... [more]

Legumes are sustainable protein-rich crops with numerous industrial food applications, which give them the potential of a functional food ingredient. Legume proteins have appreciable techno-functional properties (e.g., emulsification, foaming, water absorption), which could be affected along with its digestibility during processing. Extraction and isolation of legumes’ protein content makes their use more efficient; however, exposure to the conditions of further use (such as temperature and pressure) results in, and significantly increases, changes in the structural, and therefore functional and nutritional, properties. The present review focuses on the quality of legume protein concentrates and their changes under the influence of different physical processing treatments and highlights the effect of processing techniques on the structural, functional, and some of the nutritional, properties of legume proteins.