Interleaved converters use an increased number of power electronics switches; this may subsequently affect their reliability. However, this is an opportunity to develop fault-tolerant strategies to improve their reliability and to ensure continuity of service. This is why we herein propose, for the first time, a mathematical function to simultaneously model the healthy and faulty conditions of each switch, thus enabling a unique model of the system. This model is then used in an original fault-tolerant strategy based upon the peak current control with slope compensation. This method not only extends the stable range of the load variation but also ensures the stability in faulty conditions. Finally, the simulation results validate its effectiveness and confirm the theoretical analysis.

Surprisingly, little is known whether the net present value (NPV) used as a financial metric in budgeting and investment planning to analyse a projects’ profitability is universal. Meanwhile, the epochal green energy revolution ensuring carbon neutrality through green innovations requires enormous investments, and projects realised must ensure energy security. Therefore, there is a need to reanalyse financial metrics used in financial planning, including NPV. We eliminate this research gap and, based on data from Poland, Romania, Hungary, Croatia, the USA, the United Kingdom, Japan, Israel, and Euro Zone, explain why one may not perceive the currently used NPV formula as a universal financial metric. We show that the variable discount rate influences the time value of money. Therefore, there is a need to redefine the NPV formula. This study makes two main contributions. First, it creates new ground by revisiting the NPV formula in the emerging market context compared to stable economie... [more]

Heat, ventilation, and air conditioning (HVAC) systems are some of the most energy-intensive equipment in buildings and their faulty or inefficient operation can significantly increase energy waste. Non-Intrusive Load Monitoring (NILM), which is a software-based tool, has been a popular research area over the last few decades. NILM can play an important role in providing future energy efficiency feedback and developing fault detection and diagnosis (FDD) tools in smart buildings. Therefore, the review of NILM-based methods for FDD and the energy efficiency (EE) assessment of HVACs can be beneficial for users as well as buildings and facilities operators. To the best of the authors’ knowledge, this paper is the first review paper on the application of NILM techniques in these areas and highlights their effectiveness and limitations. This review shows that even though NILM could be successfully implemented for FDD and the EE evaluation of HVACs, and enhance the performance of these techn... [more]

To support a sustainable energy development, CO2 reduction for carbon neutralization and water-splitting for hydrogen economy are two feasible technical routes, both of which require a significant input of renewable energies. To efficiently store renewable energies, secondary batteries will be applied in great quantity, so that a considerable amount of energy needs to be invested to eliminate the waste battery electrolyte pollution caused by heavy metals including Cu2+, Zn2+ and Pb2+. To reduce this energy consumption, the removal behaviors of these ions by using clinoptilolite and zeolite A under 5, 7 and 10 BV h−1 in a fixed-bed reactor were investigated. The used zeolites were then regenerated by a novel NH4Cl solution soaking, coupled with the ultrasonication method. Further characterizations were carried out using scanning electron microscopy, N2 adsorption and desorption test, and wide-angle X-ray diffraction. The adsorption breakthrough curves revealed that the leaching preferen... [more]

The trend to replace internal combustion engines with electric zero-emission drives, visible in the automotive industry, also exists in the shipbuilding industry. In contrary to land vehicles, the requirements for the electric propulsion system of tugs are much greater, which combined with the limited space and energy on board, makes any amount of energy valuable. Strategic changes in the policy of many countries, such as the “Fit for 55” package, introduce plans to significantly reduce CO2 emissions, which favors the development of alternative drives and their introduction to new areas of operation. This article presents that it is possible to reduce the amount of energy an electric tug spends for movement by applying the Particle Swarm Optimization method to modify the shape of its hull. A statistical analysis of public data was performed to determine the speed profiles of actual port tugs. The Van Oortmerssen method was used to determine the hull resistances of the proposed tug and... [more]

The suitability of sewage-sludge derived washing agents (SS_WAs) (dissolved organic matter DOM; humic-like substances HLS; soluble humic substances SHS), was assessed for removing Cd from highly contaminated (300 mg/kg) sandy clay loam and clay. The soils were remediated via column flushing at two flow rates, 0.5 and 1.0 mL/min. The stability of the flow velocity (FV) depended on the type of SS_WA and decreased in the following order: DOM > HLS > SHS. Cd was most effectively removed during the first hours of flushing, and the process proceeded with a first-order kinetics. The overall process efficiency was higher at flow rate of 1.0 mL/min than at 0.5 mL/min and ranged from 65.7 (SHS) to 75.5% (DOM) for the sandy clay loam and from 64.7% (SHS) to 67.8% (DOM) for the clay. However, all SS_WAs at both flow rates removed the most mobile Cd fraction (F1) with an efficiency above 90%. Flushing improved soil characteristics in terms of the content of organic matter, humic substances and nutr... [more]

This article deals with options for how to express the luminous flux from outdoor electrical substations of the electric transmission system. Processing of the models of light emissions before and after refurbishment of lighting systems was motivated by setting out rules for the design and erection of refurbished lighting systems in outdoor electrical substations, which are most commonly built in inhabited rural areas with low luminance of the background. The proposed model and calculations are based on requirements of international standards and recommendations for lighting of outdoor workplaces as well as on internal regulations of the ČEPS (Czech Transmission System Operator). These requirements are implemented in real electrical substations and lighting models that are extended by the calculation space of the software goniophotometer. The software goniophotometer was used to evaluate light distribution characteristics of entire electric stations in various situations. This article... [more]

Natural gas consumption depends on many factors. Some of them, such as weather conditions or historical demand, can be accurately measured. The authors, based on the collected data, performed the modeling of temporary and future natural gas consumption by municipal consumers in one of the medium-sized cities in Poland. For this purpose, the machine learning algorithms, neural networks and two regression algorithms, MLR and Random Forest were used. Several variants of forecasting the demand for natural gas, with different lengths of the forecast horizon are presented and compared in this research. The results obtained using the MLR, Random Forest, and DNN algorithms show that for the tested input data, the best algorithm for predicting the demand for natural gas is RF. The differences in accuracy of prediction between algorithms were not significant. The research shows the differences in the impact of factors that create the demand for natural gas, as well as the accuracy of the predict... [more]

The steady mixing of gas-liquid systems is used where a large development of the interfacial area is required. However, the presence of gas in the liquid reduces the efficiency of mass transfer by reducing the mixing power, due to the creation of gas formations behind the impeller blades and the reduction in density. The efficiency of mass transfer can be increased by using a concave blade impeller or unsteady mixing. Mass transfer efficiency studies for these impellers and unsteady mixing are limited. This paper presents an analysis of the influence of the impeller construction on the gas hold-up and volumetric mass transfer coefficient kLa. Impellers with a different number of concave blades, and with alternatively arranged concave blades, were analyzed. The obtained results were compared with the standard flat blade turbine. The obtained results indicate that the arrangement of the concave blades has the greatest effect on reducing the gas hold-up and kLa. Higher values were obtaine... [more]

In this work, a 3D multi-physics coupled model was developed to analyze the temperature and thermal stress distribution in a planar solid oxide fuel cell (SOFC) stack, and then the effects of different flow channels (co-flow, counter-flow and cross-flow) and electrolyte thickness were investigated. The simulation results indicate that the generated power is higher while the thermal stress is lower in the co-flow mode than those in the cross-flow mode. In the cross-flow mode, a gas inlet and outlet arrangement is proposed to increase current density by about 10%. The generated power of the stack increases with a thin electrolyte layer, but the temperature and its gradient of the stack also increase with increase of heat generation. The thermal stress for two typical sealing materials is also studied. The predicted results can be used for design and optimization of the stack structure to achieve lower stress and longer life.

On 11 March 2020, the WHO declared the COVID-19 epidemic to be a global pandemic. This was a consequence of the rapid increase in the number of people with positive test results, the increase in deaths due to COVID-19, and the lack of pharmaceutical drugs. Governments introduced national lockdowns, which have impacted both energy consumption and economies. The purpose of this paper is to answer the following question: do COVID-19 lockdowns affect the business cycle? We used the cycle clock approach to assess the magnitude of decrease in electricity consumption in the three waves of the epidemic, namely, April 2020, November 2021, and April 2021. Additionally, we checked the relation between energy consumption and GDP by means of spectral analysis. Results for selected 28 European countries confirm an impact of the introduced non-pharmaceutical interventions on both energy consumption and business cycle. The reduction of restrictions in subsequent pandemic waves increased electricity co... [more]

As the demands of tight-oil Enhanced Oil Recovery (EOR) and the controlling of anthropogenic carbon emission have become global challenges, Carbon Capture Utilization and Sequestration (CCUS) has been recognized as an effective solution to resolve both needs. However, the influential factors of carbon dioxide (CO2) geological storage in low permeability reservoirs have not been fully studied. Based on core samples from the Huang-3 area of the Ordos Basin, the feasibility and influential factors of geological CO2 sequestration in the Huang-3 area are analyzed through caprock breakthrough tests and a CO2 storage factor experiment. The results indicate that capillary trapping is the key mechanism of the sealing effect by the caprock. With the increase of caprock permeability, the breakthrough pressure and pressure difference decreased rapidly. A good exponential relationship between caprock breakthrough pressure and permeability can be summarized. The minimum breakthrough pressure of CO2... [more]

A new procedure, based on measurement of intake CO2 concentration and ambient humidity was developed and assessed in this study for different diesel engines in order to evaluate the oxygen concentration in the intake manifold. Steady-state and transient datasets were used for this purpose. The method is very fast to implement since it does not require any tuning procedure and it involves just one engine-related input quantity. Moreover, its accuracy is very high since it was found that the absolute error between the measured and predicted intake O2 levels is in the ±0.15% range. The method was applied to verify the performance of a previously developed NOx model under transient operating conditions. This model had previously been adopted by the authors during the IMPERIUM H2020 EU project to set up a model-based controller for a heavy-duty diesel engine. The performance of the NOx model was evaluated considering two cases in which the intake O2 concentration is either derived from engi... [more]

Energy Storage Systems (ESS) are an attractive solution in environments with a high amount of renewable energy sources, as they can improve the power quality in such places and if required, can extend the integration of more renewable sources of energy. If a large amount of power is needed, then supercapacitors are viable energy storage devices due to their specific power, allowing response times that are in the range of milliseconds to seconds. This paper details the design of an ESS that is based on a modular multilevel converter (MMC) with bidirectional power flow, which reduces the number of cascaded stages and allows the supercapacitors SCs to be connected to the grid to perform high-power transfers. A traditional ESS has four main stages or subsystems: the energy storage device, the balancing system, and the DC/DC and DC/AC converters. The proposed ESS can perform all of those functions in a single circuit by adopting an MMC topology, as each submodule (SM) can self-balance durin... [more]

This paper discusses the research and analysis of the dynamics of high-voltage generating systems. The test subject is an ignition system modelled by a set of two induction coils with an open ferromagnetic core that constitutes an ignition coil. The essence of the tests involved the application of magnetic coupling of the fractional order that enabled taking into account the non-idealities of the coils and the connector that implements the ignition point. The paper contains the results of a theoretical analysis, supported by digital simulations. The conducted experiments confirm the purposefulness of the conducted analyses and the possibility of modeling real objects based on circuits with fractional-order elements.

Hydrofracturing, used for shale gas exploitation, may induce felt, even damaging earthquakes. On 15 June 2019, an Mw2.8 earthquake occurred, spatially correlated with the location of earlier exploratory hydrofracturing operations for shale gas in Wysin in Poland. However, this earthquake was atypical. Hydrofracturing-triggered seismicity mainly occurs during stimulation; occasionally, it continues a few months after completion of the stimulation. In Wysin, there were only two weaker events during two-month hydrofracturing and then 35 months of seismic silence until the mentioned earthquake occurred. The Wysin site is in Gdańsk Pomerania broader region, located on the very weakly seismically active Precambrian Platform. The historical documents, covering 1000 years, report no natural earthquakes in Gdańsk Pomerania. We conclude, therefore, that despite the never observed before that long lag time after stimulation, the Mw2.8 earthquake was triggered by hydrofracturing. It is possible th... [more]

Producing chemical fuels from sunlight is a sustainable way to utilize solar energy and reduce carbon emissions. Within the current photovoltaic-electrolysis or photoelectrochemical-based solar fuel generation system, electrochemical CO2 reduction is the key step. Although there has been important progress in developing new materials and devices, scaling up electrochemical CO2 reduction is essential to promote the industrial application of this technology. In this work, we use Ag and In as the representative electrocatalyst for producing gas and liquid products in both small and big electrochemical cells. We find that gas production is blocked more easily than liquid products when scaling up the electrochemical cell. Simulation results show that the generated gas product, CO, forms bubbles on the surface of the electrocatalyst, thus blocking the transport of CO2, while there is no such trouble for producing the liquid product such as formate. This work provides methods for studying the... [more]

Quantifying the wider benefits of energy efficient building retrofits is crucial to incentivise householder retrofit investments. This research recognises the value of key performance indicators (KPIs) for assessing and demonstrating retrofitting benefits and provides an assessment of KPIs for evaluating retrofits. An integrated framework for evaluating retrofits using a set of economic, social, and environmental KPIs is proposed. This KPI framework is then applied in a pre- and post-retrofit assessment of five case study dwellings located in Ireland, revealing its usefulness in demonstrating the wider benefits of retrofitting to householders, with a view to driving retrofit investment. Three of these case study dwellings had state-of-the-art retrofit technologies installed as part of the works, including heat pumps and solar PV systems. In addition to demonstrating the wider benefits of retrofitting, the framework allowed for the identification of potential causes for differences in p... [more]

Food waste is an important constituent of municipal solid waste, and research has been conducted to develop various methods for treating food waste and recycling it (e.g., fuel, landfilling, composting, conversion into animal feed, drying, and carbonization). Among these, the drying and carbonization techniques can change food waste into fuel; however, they need more energy than fermentation and anaerobic digestion procedures. In this study, we investigated the physicochemical properties of food waste biochar produced under torrefaction (270 °C) and pyrolysis (450 °C) conditions to establish its applicability as fuel by comparing temperatures, residence times, and conditions before and after demineralization. The higher heating value increased after the demineralization process under both temperature conditions (270 °C and 450 °C), and the chlorine level was lower at 270 °C temperature demineralization than at 450 °C. During the demineralization process, Na and K were better removed th... [more]

A demonstration of the relationship between the share of renewables in gross marginal energy and selected countries’ economic growth is the basis of this research. The paper seeks to investigate mutual correlations between renewable energy sources and economic growth for two EU economies and how it influences their fluctuations (increase and decrease). The comparative analysis of results was carried out for less-income Polish and high-income Swedish economies. This research used a regression model to answer the research questions examining the presence of correlations between renewable energy sources in gross marginal energy consumption and economic growth. This study analyzes data starting from 1991 to 2022. The results indicated a positive correlation (statistical significance) between Gross Domestic Product and Gross National Income variables for Sweden (84.6% and 83.7%, respectively) and Poland (79.9% and 79.2%, respectively), which influence the use of renewable energy sources. Th... [more]

Straw is treated as agricultural waste, and it is available in almost every region of Poland. A total of 30 million tons of straw is produced per year, of which there is a surplus of approximately 13.5 million tons of undeveloped straw. For energy purposes, straw from cereals or rapeseed is most often used. When analyzing scientific publications, it was noticed that, in Poland, large amounts of oat straw are produced, and there is no alternative use for it. Hence, we conducted research to determine the energy value of oat straw. Raw material was obtained from an individual farm from 2018 to 2020. Selected energy parameters for straw burned alone (100%) or co-fired with coal were analyzed in the following weight proportions: 70/30, 80/20, and 90/10 coal/oat straw. It was shown that changing weather conditions, in particular years, had a modifying effect on some of the energy parameters of straw. The calorific value of straw was lower than that of coal, but its impact on environmental po... [more]

Peak load reduction is one of the most essential obligations and cost-effective tasks for electrical energy consumers. An isolated microgrid (IMG) system is an independent limited capacity power system where the peak shaving application can perform a vital role in the economic operation. This paper presents a comparative analysis of a categorical variable decision tree algorithm (CVDTA) with the most common peak shaving technique, namely, the general capacity addition technique, to evaluate the peak shaving performance for an IMG system. The CVDTA algorithm deals with the hybrid photovoltaic (PV)—battery energy storage system (BESS) to provide the peak shaving service where the capacity addition technique uses a peaking generator to minimize the peak demand. An actual IMG system model is developed in MATLAB/Simulink software to analyze the peak shaving performance. The model consists of four major components such as, PV, BESS, variable load, and gas turbine generator (GTG) dispatch mod... [more]

Energy-poverty (EP) must be considered an energy-related issue since buildings are a central part of people’s daily lives. Thus, it has an important role in energy-related policy implementation. Even though the European Union (EU) has endorsed general energy efficiency through the Energy Efficiency Directive and Energy Performance of Buildings Directive recast, it was the Clean Energy Package for all Europeans that clearly highlighted EP. The growing concerns with EP have also been emphasised in subsequent directives and initiatives. Despite some regulatory framework and the milder climate situation, the proportion of the population experiencing thermal discomfort in southern and eastern European countries, namely in the winter season, is relatively high, reflecting the poor thermal performance of building stock, low family incomes and high energy prices, among others. The current work analysed the EP evolution in Portugal in the EU context, and the Thermal Building Regulations and Ene... [more]

The Trombe wall is a passive system used in buildings that indirectly transfers thermal energy to the adjacent environment by radiation and convection, and directly by the thermo-circulation that arises in the air cavity delimited between a transparent and an absorbing surface. Nevertheless, the latter is painted black to increase the energy gains, but this produces a negative visual impact and promotes the overheating risk in summer. To mitigate these aspects, a hybrid Trombe wall equipped with PV panels can be employed. The PV installation results in a more pleasing wall appearance and the overheating risk reduces because part of the absorbed solar radiation is transformed into electricity. To determine the actual performance of a such system, transient simulation tools are required to consider properly the wall thermal storage features, variation of the optical properties, air thermo-circulation, and PV power production. Alternatively, regarding the traditional Trombe wall, the lite... [more]

Mechanical systems (as belt conveyors) used in the mining industry, especially in deep underground mines, must be supervised on a regular basis. Unfortunately, they require high power and are spatially distributed over a large area. Till now, some elements of the conveyor (drive units) have been monitored 24 h/day using SCADA systems. The rest of the conveyor is inspected by maintenance staff. To minimize the presence of humans in harsh environments, we propose a mobile inspection platform based on autonomous UGV. It is equipped with various sensors, and in practice it is capable of collecting almost the same information as maintenance inspectors (RGB image, sound, gas sensor, etc.). Till now such experiments have been performed in the lab or in the mine, but the robot was controlled by the operator. In such a scenario the robot is able to record data, process them and detect, for example, an overheated idler. In this paper we will introduce the general concept of an automatic robot-ba... [more]