Oxy-fuel combustion is one of the most promising methods for CO₂ capture and storage (CCS) but the operating costs—mainly due to the need for oxygen production—usually lead to an obvious decrease in power generation efficiency. An “oxy-enrich combustion” process was proposed in this study to improve the efficiency of the oxy-fuel combustion process. The oxidizer for oxy-enrich combustion was composed of pure oxygen, air and recycled flue gas. Thus, the CO₂ concentration in the flue gas decreased to 30⁻40%. The PSA (pressure swing adsorption), which has been widely used for CO₂ removal from the shifting gases of ammonia synthesis in China, was applied to capture CO₂ during oxy-enrich combustion. The technological economics of oxy-enrich combustion with PSA was calculated and compared to that of oxy-fuel combustion. The results indicated that, compared with oxy-fuel combustion: (1) the oxy-enrich combustion has fewer capital and operating costs for the ASU (air separation unit) and the r... [more]

Photovoltaic (PV) arrays can be connected following regular or irregular connection patterns to form regular configurations (e.g., series-parallel, total cross-tied, bridge-linked, etc.) or irregular configurations, respectively. Several reported works propose models for a single configuration; hence, making the evaluation of arrays with different configuration is a considerable time-consuming task. Moreover, if the PV array adopts an irregular configuration, the classical models cannot be used for its analysis. This paper proposes a modeling procedure for PV arrays connected in any configuration and operating under uniform or partial shading conditions. The procedure divides the array into smaller arrays, named sub-arrays, which can be independently solved. The modeling procedure selects the mesh current solution or the node voltage solution depending on the topology of each sub-array. Therefore, the proposed approach analyzes the PV array using the least number of nonlinear equations... [more]

This paper suggests an innovative approach for the ideal placement and categorization of capacitors in radial distribution networks (RDNs) by applying symmetric fuzzy and improved bacterial foraging optimization algorithm (IBFOA) solutions. The reactive power reimbursement significantly enhances the function of the power system, and capacitor placement is an impressive technique used to reduce loss of the system. The capacitor allocation for distribution system problems involves determining the ideal location and size of the capacitor. In this work, load flow is performed at first to compute actual losses and voltages at different nodes without compensation. In the planned technique, the loss sensitivity factor (VSF) and voltage stability index (VSI) are utilized to determine the optimal location of capacitors in RDNs. Here, the IBFOA is used to determine the proper rating of the capacitor. The suggested scheme is applied on three different types of RDNs.

The hydrophobicity of composite insulators is a great significance to the safe and stable operation of transmission lines. In this paper, a recognition method of the hydrophobicity class (HC) of composite insulators based on features optimization was proposed. Through the spray method, many hydrophobic images of water droplets on the insulator surface at various hydrophobicity classes (HCs) were taken. After processing of the hydrophobic images, seven features were extracted: the number n, mean eccentricity Eav and coverage rate k₁ of the water droplets, and the coverage rate k₂, perimeter Lmax, shape factor fc, and eccentricity Emax of the maximum water droplet. Then, the maximum value Δxmax, the minimum value Δxmin, and the average value Δxav of the change rate of each feature value between adjacent HCs, and the volatility Δs of each feature value, were used as the evaluation indexes for features optimization. After this features optimization, the five features that are most closely... [more]

Electrical tree is a serious threat to silicone rubber (SIR) insulation and can even cause breakdown. Electrical trees under alternating current (AC) and direct current (DC) voltage have been widely researched. While there are pulses in high-voltage direct current (HVDC) cables under operating conditions caused by lightning and operating overvoltage in the power system, little research has been reported about trees under combined DC-pulse voltage. Their inception and growth mechanism is still not clear. In this paper, electrical trees are studied under several types of combined DC-pulse voltage. The initiation and growth process was recorded by a digital microscope system. The experimental results indicate that the inception pulse voltage is different under each voltage type and is influenced by the combined DC. The initial tree has two structures, determined by the pulse polarity. With increased DC prestressing time, tree inception pulse voltage with the same polarity is clearly decre... [more]

With the massive penetration of intermittent generation (wind and solar), the reduction of Electrical Power Systems’ (EPSs) inertial frequency response represents a new challenge. One alternative to deal with this scenario may be the application of a Battery Energy Storage System (BESS). However, the main constraint for the massive deployment of BESSs is the high acquisition cost of these storage systems which in some situations, can preclude their use in transmission systems. The main goal of this paper is to propose a systematic procedure to include BESSs in power system aiming to improve the power system frequency response using full linear models and geometric measures. In this work, a generic battery model is developed in a two-area test system with assumed high wind penetration and full conventional generators models. The full power system is linearized, and the geometric measures of controllability associated with of the frequency regulation mode are estimated. Then, these resul... [more]

Excess heat is present in many sectors, and its utilization could reduce the primary energy use and emission of greenhouse gases. This work presents a geographical mapping of excess heat, in which excess heat from the industry and utility sector was distributed to specific geographical locations in Denmark. Based on this mapping, a systematic approach for identifying cases for the utilization of excess heat is proposed, considering the production of district heat and process heat, as well as power generation. The technical and economic feasibility of this approach was evaluated for six cases. Special focus was placed on the challenges for the connection of excess heat sources to heat users. To account for uncertainties in the model input, different methods were applied to determine the uncertainty of the results and the most important model parameters. The results show how the spatial mapping of excess heat sources can be used to identify their utilization potentials. The identified ca... [more]

The increasing proportion of intermittent renewable energies asks for further technologies for balancing demand and supply in the energy system. In contrast to other countries, Germany is characterized by a high installed capacity of dispatchable biogas plants. For this paper, we analyzed the total system costs varying biogas extension paths and modes of operation for the period of 2016⁻2035 by using a non-linear optimization model. We took variable costs of existing conventional power plants, as well as variable costs and capital investments in gas turbines, Li-ion batteries, and pumped-storage plants into account. Without the consideration of the costs for biogas plants, an increasing proportion of biogas plants, compared to their phase out, reduces the total system costs. Furthermore, their flexible power generation should be as flexible as possible. The lowest total system costs were calculated in an extension path with the highest rate of construction of new biogas plants. However... [more]

The conductor temperature of an overhead transmission line varies with time and space, which has an important impact on the system operation. In this paper, the conductor temperature is solved iteratively by the CIGRE heat balance equation. The time⁻space variation of conductor temperature of a 220-kV transmission line is analyzed using real meteorological data from Weihai. Considering the temporal distribution characteristics, the seasonal model of the conductor temperature is given. Considering the spatial distribution, the mean value model, the weight average model, and the segmentation model are established. The system power flow involving the conductor temperature is established based on the relationship between conductor temperature and transmission line parameters. Through the calculation of power flow and the analysis of the maximum power transmission capability, the accuracy of the segmentation model is verified. The results show that the conductor temperature of overhead line... [more]

Microgrids play an important role in today’s power systems as the distributed generation is becoming increasingly common. They can operate in two possible modes: (i) standalone and (ii) grid-connected. The transitional state from standalone to grid-connected mode is very critical and requires the microgrid to be synchronized with the main grid. Thus, secure, reliable and trustworthy control and communication is utmost necessary to prevent out-of-sync connection which could severely damage the microgrid and/or the main grid. Existing solutions consume more resources and take long time to establish a secure connection. The objective of the proposed work is to reduce the connection establishment time by using efficient computational algorithms and save the resources. This paper proposes a secure authentication and key establishment mechanism for ensuring safe operation and control of the microgrids. The proposed approach uses the concept of Elgamal with slight modification. Private key of... [more]

In this paper, the appropriate rated power of battery energy storage system (BESS) and the operating limit capacity of wind farms are determined considering power system stability, and novel output control methods of BESS and wind turbines are proposed. The rated power of BESS is determined by correlation with the kinetic energy that can be released from wind turbines and synchronous generators when a disturbance occurs in the power system. After the appropriate rated power of BESS is determined, a novel control scheme for quickly responding to disturbances should be applied to BESS. It is important to compensate the insufficient power difference between demand and supply more quickly after a disturbance, and for this purpose, BESS output is controlled using the rate of change of frequency (ROCOF). Generally, BESS output is controlled by the frequency droop control (FDC), however if ROCOF falls below the threshold, BESS output increases sharply. Under this control for BESS, the power s... [more]

The evolution of pore structure during in situ underground exploitation of oil shale directly affects the diffusion and permeability of pyrolysis products. In this study, on the basis of mineral analysis and thermogravimetric results, in combination with the low-pressure nitrogen adsorption (LPNA) and mercury intrusion porosimetry (MIP) technique, the evolution of pore structure from 23 to 650 °C is quantitatively analyzed by simulating in situ pyrolysis under pressure and temperature conditions. Furthermore, based on the experimental results, we analyze the mechanism of pore structure evolution. The results show the following: (1) The organic matter of Fushun oil shale has a degradation stage in the temperature range of 350⁻540 °C, and there is no obvious temperature gradient between decomposition of kerogen and the secondary decomposition of bitumen. The thermal response mechanisms of organic matter and minerals are different in each temperature stage, and influence the change of por... [more]

The strict operational condition of driving motors for vehicles propels the development of more complicated configurations in pure electric vehicles (PEVs). Multi-power-source powertrain configurations are one of the efficient technologies to reduce the manufacturing difficulty of driving motors. However, most of the existing studies are predominantly focused on optimal designs of powertrains and power distribution between the engine and motor of hybrid electric vehicles, which are not appropriate for PEVs. This paper proposes a novel dual-motor coupling-propulsion powertrain system that improves the dynamic and economic performance of the powertrain system in PEVs. The proposed powertrain system can realize both the single-motor driving mode and dual-motor coupling driving mode. The driving modes are divided and a power distribution strategy for the different driving modes based on an optimal system efficiency rule is employed, which enhances the performance of the proposed system. Fu... [more]

In order to design a well-performing hybrid storage system for trams, optimization of energy management strategy (EMS) and sizing is crucial. This paper proposes an improved EMS with energy interaction between the battery and supercapacitor and makes collaborative optimization on both sizing and EMS parameters to obtain the best working performance of the hybrid storage system. This paper demonstrates the whole process of the improvement of the EMS, the traction calculation, the parameter optimization, and the sizing optimization based on real tram and line conditions. The improved strategy is proven to be superior as it guarantees normal operation and avoids shutdown conditions when the supercapacitor is at a low voltage. Furthermore, the optimized sizing result largely decreases the weight of the storage system and obtains a long battery lifespan.

The lands in the northernmost corner of Europe present contradictory aspects in their social and economic development. Urban settlements are relatively few and small-sized, but rich natural resources (minerals, forests, rivers) attract energy-intensive industries. Energy demand is increasing as a result of new investments in mining and industries, while reliable energy supply is threatened by the planned phase out of Swedish nuclear power, the growth of intermittent power supplies and the need to reduce fossil fuel consumption, especially in the Finnish and Norwegian energy sectors. Given these challenges, this paper investigates the potentials of so far unexploited energy resources in the northern counties of Finland, Norway and Sweden by comparing and critically analyzing data from statistic databases, governmental reports, official websites, research projects and academic publications. The criteria for the technical and economic definition of potentials are discussed separately for... [more]

In recent years, the ultra-high voltage direct current (UHVDC) transmission system has been developed rapidly for its significant long-distance, high-capacity and low-loss properties. Equipment failures and overall outages of the UHVDC system have increasingly vital influence on the power supply of the receiving end grid. To improve the reliability level of UHVDC systems, a quantitative selection and configuration approach of redundant structures is proposed in this paper, which is based on multi-state reliability equivalence. Specifically, considering the symmetry characteristic of an UHVDC system, a state space model is established as a monopole rather than a bipole, which effectively reduces the state space dimensions to be considered by deducing the reliability merging operator of two poles. Considering the standby effect of AC filters and the recovery effect of converter units, the number of available converter units and corresponding probability are expressed with in universal ge... [more]

Accurate prediction of the hoop stress distribution of the cement sheath and its variation regularities during volume hydraulic fracturing in shale formations is of great significance for maintaining the wellbore integrity of shale gas horizontal wells. A finite element model of casing-cement sheath-formation system (CCFS) coupling between stresses and temperature was established through a staged finite element method based on the elastic anisotropy of shale. With this new model, the effects of operation parameters and formation mechanical property changes on the cement sheath hoop stress during the multi-stage hydraulic fracturing process were analyzed, and the results were compared with the conventional model. The results revealed that the increase of the temperature of the fracturing fluid could reduce the hoop stress of the cement sheath, which decreased gradually with the decreasing elastic modulus of the cement sheath, and eventually changed to compressive stress from tensile str... [more]

This article states a condition monitoring strategy for wind turbines using a statistical data-driven modeling approach by means of supervisory control and data acquisition (SCADA) data. Initially, a baseline data-based model is obtained from the healthy wind turbine by means of multiway principal component analysis (MPCA). Then, when the wind turbine is monitorized, new data is acquired and projected into the baseline MPCA model space. The acquired SCADA data are treated as a random process given the random nature of the turbulent wind. The objective is to decide if the multivariate distribution that is obtained from the wind turbine to be analyzed (healthy or not) is related to the baseline one. To achieve this goal, a test for the equality of population means is performed. Finally, the results of the test can determine that the hypothesis is rejected (and the wind turbine is faulty) or that there is no evidence to suggest that the two means are different, so the wind turbine can be... [more]

Total organic carbon (TOC), a critical geochemical parameter of organic shale reservoirs, can be used to evaluate the hydrocarbon potential of source rocks. However, getting TOC through core analysis of geochemical experiments is costly and time-consuming. Therefore, in this paper, a TOC prediction model was built by combining the data from a case study in the Ordos Basin, China and core analysis with artificial intelligence techniques. In the study, the data of samples were optimized based on annealing algorithm (SA) and genetic algorithm (GA), named SAGA-FCM method. Then, back propagation algorithm (BPNN), least square support vector machine (LSSVM), and least square support vector machine based on particle swarm optimization algorithm (PSO-LSSVM) were built based on the data from optimization. The results show that the intelligence model constructed based on core samples data after optimization has much better performance in both training and validation accuracy than the model const... [more]

This article offers reasons to defend the use of generic behavior models as opposed to specific models in applications to determine component degradation. The term generic models refers to models based on operating data from various units, whereas specific models are calculated using operating data taken from a single unit. Moreover, generic models, used in combination with a status indicator, show excellent capacity for detecting anomalies in the equipment and for evaluating the effectiveness of the maintenance actions, resulting in lower development and maintenance costs for the operating firm. Artificial neural networks and moving means were used to calculate the degradation indicators, based on the remainders in the model. The models were developed from operating data from fourteen wind turbines monitored over several years, and applied to the detection of faults in the bearings on the non-drive end of the generator. The use of generic models may not be recommendable for detecting... [more]

Among the issues of accurate power distribution, stability improvement, and harmonic suppression in micro-grid, each has been well studied as an individual, and most of the strategies about these issues aim at one inverter-based micro-grid, hence there is a need to establish a model to achieve these functions as a whole, aiming at a multi-inverter-based micro-grid. This paper proposes a comprehensive strategy which achieves this goal successfully; since the output voltage and frequency of micro-grid all consist of fundamental and harmonic components, the strategy contains two parts accordingly. On one hand, a fundamental control strategy is proposed upon the conventional droop control. The virtual impedance is introduced to solve the problem of accurate allocation of reactive power between inverters. Meanwhile, a secondary power balance controller is added to improve the stability of voltage and frequency while considering the aggravating problem of stability because of introducing vir... [more]

The electrical system of a wind farm has a significant influence on the wind farm reliability and electrical energy yield. The disconnect switch installed in an electrical system cannot only improve the operating flexibility, but also enhance the reliability for a wind farm. Therefore, this paper develops a probabilistic transfer technique for integrating the electrical topology structure, the isolation operation of disconnect switch, and stochastic failure of electrical equipment into the reliability assessment of wind farm electrical system. Firstly, as the traditional two-state reliability model of electrical equipment cannot consider the isolation operation, so the paper develops a three-state reliability model to replace the two-state model for incorporating the isolation operation. In addition, a proportion apportion technique is presented to evaluate the state probability. Secondly, this paper develops a probabilistic transfer technique based on the thoughts that through transfe... [more]

The integration of renewable energies into combined cooling, heating, and power (CCHP) systems has become increasingly popular in recent years. However, the optimization of renewable energies integrated CCHP (RECCHP) systems (i.e., optimal component configurations) is far from being well addressed, especially in isolated mode. This study aims to fill this research gap. A multi-objective optimization model characterizing the system reliability, system cost, and environmental sustainability is constructed. In this model, the objectives include minimization of annual total cost (ATC), carbon dioxide emission (CDE), and loss of energy supply probability (LESP). The decision variables representing the configuration of the RECCHP system include the number of photovoltaic (PV) panels and wind turbines (WTs), the tilt angle of PV panels, the height of WTs, the maximum fuel consumption, and the capacity of battery and heat storage tanks (HSTs). The multi-objective model is solved by a multi-obj... [more]

Strata movement boundary is not only a parameter for the prediction of overburden strata movement and deformation but also a key index of setting shafts, roadways and protective coal pillars. Based on physical and mechanical properties of rock mass, the overburden strata are divided into bedrock and unconsolidated stratum. By means of theoretical analysis, physical simulation and numerical simulation, this paper studies the movement boundary shapes of bedrock and unconsolidated stratum, builds fitting equations of movement boundary of the two, analyzes the influence of key strata (KS) on the shape of strata movement boundary, and determines the principle of setting protective coal pillars. The results show that the movement boundaries of bedrock and unconsolidated strata are located at the outside of coal mining boundary. They are concave-upward power function curves that cannot be merged into a smooth one due to their different mechanisms of movement and deformation. The movement boun... [more]

With the increasing penetration of renewable energy, it is difficult to schedule unit commitment (UC) in a power system because of the uncertainty associated with various factors. In this paper, a new solution procedure based on a multi-scenario tree method (MSTM) is presented and applied to the proposed stochastic UC problem. In this process, the initial input data of load and wind power are modeled as different levels using the mean absolute percentage error (MAPE). The load and wind scenarios are generated using Monte Carlo simulation (MCS) that considers forecasting errors. These multiple scenarios are applied in the MSTM for solving the stochastic UC problem, including not only the load and wind power uncertainties, but also sudden outages of the thermal unit. When the UC problem has been formulated, the simulation is conducted for 24-h period by using the short-term UC model, and the operating costs and additional reserve requirements are thus obtained. The effectiveness of the p... [more]