This paper investigates how the pre-treatment of the growth solution with ultrasonic energy affects the annealing temperatures and the growth temperatures of zinc oxide (ZnO) nanorods. The ultrasonic pre-treatment of the growth solution resulted in the successful growth of ZnO nanorods at a very low annealing temperature of 40 °C. The size and density of ZnO nanorods were found to increase proportionally with the increasing duration of pre-ultrasonic treatment, as indicated by characterisations performed with a scanning electron microscope (SEM). At an annealing temperature of 40 °C, coupled with ultrasonic waves, the SEM results showed that ZnO nanorods’ length and diameter increased by 37 and 25%. A similar pattern was also observed at an annealing temperature of 60 and 80 °C, where the length and diameter of ZnO nanorods increased. In addition, the conductivity and acidity of the aqueous solution that had been sonicated were measured. The results showed that solution conductivity an... [more]

The molecular structure of cationic surfactants is closely related to their flotation performance. In this paper, three cationic surfactants with different head group structures were selected as collectors of kaolinite, and the substituent effects were studied by the DFT method. The DFT calculation results showed that increasing the number of substituents in the dodecylamine head group can significantly increase its surface and head group charge. Dodecylamine has the lowest LUMO orbital energy, so dodecylamine has the strongest electron attraction ability and the strongest interaction with kaolinite. Electron density differential showed that there was an area of electron aggregation between the collector and the surface of the kaolinite. The interaction energy of DDA on kaolinite surfaces was greater than that of the other two collectors, indicating that the adsorption of DDA on the surface of kaolinite was more stable. Flotation results showed that higher a kaolinite yield was obtaine... [more]

Wound healing is the process of skin and soft tissue repair following an injury. Angiogenesis is an essential process in wound healing and plays an important role in tissue regeneration. Ginseng is mainly composed of saponins and protopanaxadiol-based ginsenosides, namely Rb1, Rb2, Rc, Re, Rg1, and Rf. 20(S)-protopanaxadiol (PPD) and 20(S)-protopanaxatriol (PPT) are aglycones of ginsenosides produced by metabolic processes and heat treatment. This study aimed to investigate the wound healing effects of active ingredients of ginseng, namely ginsenosides and aglycones, in various cellular and animal skin wound models. The angiogenic effects of ginsenosides were investigated in human umbilical vein endothelial cells (HUVECs). All experiments were conducted at increased intracellular glucose concentrations and the induction of angiogenesis through tube formation was evaluated. Among the ginsenosides and aglycones used in this study, PPD showed the strongest wound-healing activity. Cell scr... [more]

Many oil wells in closed reservoirs continue to produce in the pseudo-steady-state flow regime for a long time. The principal objective of this work is to investigate the characteristics of two key pseudo-steady-state parameters—pseudo-steady-state constant (bDpss) and pseudo-skin factor (S)—for a well penetrated by a fracture with an azimuth angle (θ) in an anisotropic reservoir. Firstly, a general analytical pressure solution for a finite-conductivity fracture with or without an azimuth angle in an anisotropic rectangular reservoir was developed by using the point-source function and spatial integral method, and two typical cases were employed to verify this solution. Secondly, with the asymptotic analysis method, the expressions of pseudo-steady-state constant and pseudo-skin factor were obtained on the basis of their definitions, and the effects of permeability anisotropy, fracture azimuth angle, fracture conductivity and reservoir shape on them were discussed in detail. Results sh... [more]

A coupled structural decomposition analysis (SDA) and sensitivity analysis approach is developed to explore the drivers of China’s CO2 emission intensity at both general and sectoral levels and from both ex-post and ex-ante perspectives. Two steps are involved—structural decomposition and sensitivity analysis. First, the popular factor decomposition method, SDA, is implemented to identify which drivers “have” made the largest contribution to emission intensity changes. Second, an emerging ex-ante approach, sensitivity analysis, is introduced to answer how and to what extent such drivers “will” influence future emission intensity at a sectoral level. Based on China’s input-output tables for 1997−2012, the empirical study provides a hotspot map of China’s energy system. (1) Direct-emission coefficient and technology coefficient are observed as the top two overall drivers. (2) For the former, reducing direct-emission coefficient in an emission-intensity sector (e.g., electricity and heat... [more]

Anaerobic fermentation with biogas as an energy source is influenced by the presence of heavy metals. However, the availability of the heavy metals is dependent on the digestion temperature. In this study, the impacts of Cd on the characteristics of biogas, substrate biodegradation, and enzyme activity during anaerobic co-digestion were investigated under varying digestion temperatures. The results showed that 1 mg/L initial Cd concentration improved cumulative biogas yields by 404.96%, 16.93%, and 5.56% at 55 °C, 45 °C, and 35 °C, respectively. In contrast, at low temperatures (25 °C), the yield decreased by 0.77%. In the 55 °C group, Cd addition improved the activity of cellulase (p < 0.05) and coenzyme F420 (p < 0.01). The total chemical oxygen demand (COD) during the peak period and the transformation of hydrolytic organic components into volatile fatty acids (VFAs) influenced the CH4 and biogas yields. There were no significant differences in cellulase, dehydrogenase, and co... [more]

In the present work, the cooling efficiency of water droplets falling onto hot aluminum and stainless steel discs from heights of 12.5 cm, 25 cm, 50 cm and 100 cm, corresponding to speeds of 1.5 m/s, 2.2 m/s, 3.1 m/s and 4.4 m/s, respectively, were studied. The discs were aligned at 0° (horizontal), 30° and 60° inclination. The water application rate was 0.022 g/s and the droplet diameters studied were 2.5 mm, 3.2 mm and 3.7 mm. Acetone solutions (300 ppm and 700 ppm) as well as a NaCl (35 g/kg) solution, emulating seawater, were tested to evaluate the influence of an active surfactant on the recorded cooling efficiency. The droplets with higher impact speed resulted in lower cooling efficiency, especially at disc temperatures above the Leidenfrost temperature, likely due to more vigorous droplets bouncing. Larger inclination did, as expected, result in lower cooling efficiency. At temperatures associated with nucleate boiling, the water droplets with NaCl conspicuously displayed highe... [more]

This article intends to promote the usage of potato peels as efficient substrate for the anaerobic digestion process for energy recovery and waste abatement. This study examined the performance of anaerobic digestion of potato peels in different inoculum-to-substrate ratios. In addition, the impact of combined treatment with cow manure and pretreatment of potato peels was examined. It was found that co-digestion of potato peel waste and cow manure yielded up to 237.4 mL CH4/g VSadded, whereas the maximum methane yield from the mono-digestion of potato peels was 217.8 mL CH4/g VSadded. Comparing the co-digestion to mono-digestion of potato peels, co-digestion in PPW/CM ratio of 60:40 increased the methane yield by 10%. In addition, grinding and acid hydrolysis applied to potato peels were positively effective in increasing the methane amount reaching 260.3 and 283.4 mL CH4/g VSadded respectively. Likewise, compared to untreated potato peels, pretreatment led to an elevation of the metha... [more]

Energies presents 10 papers selected from the 11th International Conference on Computational Heat, Mass and Momentum Transfer (ICCHMT2018) [...]

This paper presents the results of a comparative investigation into the effects of the ignition method on the ballistic properties of three types of propellants: a single-base propellant, a double-base propellant and a low vulnerability (LOVA) propellant, as determined via closed vessel tests (CVT). Conventional gunpowder ignition and plasma jet ignition methods were used. The influence of the ignition method on the values of the propellant characteristics obtained in CVT was analysed. It was found that the method of ignition has an influence on the values of propellant characteristics, determined in CVT. An analysis of the experimental form functions showed that plasma ignition is not a solution to the problems inherent to the process of determining the ballistic properties of propellants in which the burning process deviates from the geometric burning law.

Heat cost allocators (HCAs) have a high market share in existing buildings, which may cause problems, especially with variable heat cost allocation due to wrong readings from HCAs and/or the method used in the heat cost allocation process. That is why we proposed two easily applicable and clear methods, which may be used with two types of HCAs commonly used in the billing practice. The proposed methods were presented on the example of the actual allocation of variable heating costs for a multi-family building located in Poland, and the results of billing were compared with three other methods of variable heating costs allocation. Owing to the proposed methods, higher (K = 0.5260 for schema A, K = 0.4468 for schema B) values of the correlation coefficient between heating costs and the average indoor temperature were obtained than for the methods commonly used in accounting practice. Additionally, the use of the proposed method allows for the elimination of defective indications of heat... [more]

This article presents a study of the sampling rate effect on electrical power measurements whose definitions are based on the Conservative Power Theory (CPT). The definitions of active power and reactive power of the CPT were applied in the MATLAB® software by varying the sampling rate and using a digital power meter as a reference. The measurements were performed in scenarios with linear and non-linear loads. Due to the usage of an integral in the CPT calculus, an error was verified associated with the reactive power being inversely proportional to the sampling rate. From the present study, it is possible to conclude that depending on the sample rate, the errors associated with the reactive power measurements are unacceptable and make the CPT implementation unfeasible. The results also presented effective information about the minimal sampling rate needed to make these errors neglected and to assist in choosing suitable microprocessors for the digital implementation of the CPT. It is... [more]

The connection section between cyclones and backpass is an important configuration in multi-cyclone circulating fluidized bed boilers (CFB). In this work, the resistance coefficient of different connection modes, and connection resistance distribution from each cyclone outlet to backpass (connection branch) in one mode are defined and calculated, in order to investigate their effects on furnace solids suspension density distribution and circulation rates. Three connection modes with different overall resistance coefficients were tested experimentally and analyzed by a 1.5-dimensional model in a four-cyclone scaling CFB apparatus. Both experimental and theoretical results show that, with larger overall resistance of a connection, there are more solids suspended in the furnace bottom and fewer in the top section. The investigation of the C-type connection has revealed that when the branch resistance of the connection decreases from branch No. 1−4, the solids suspension density and circul... [more]

In several energy applications, DC/DC converters are one of the most important components [...]

In this paper is presented a Normally-OFF GaN HEMT (High Electron Mobility Transistor) device using p-doped GaN barrier layer regrown by CBE (Chemical Beam Epitaxy). The impact of the p doping on the device performance is investigated using TCAD simulator (Silvaco/Atlas). With 4E17 cm−3 p doping, a Vth of 1.5 V is achieved. Four terminal breakdowns of the fabricated device are investigated, and the origin of the device failure is identified.

The fracturing technique is widely used in many fields. Fracture has a greater impact on the movement of fluids in formations. Knowing information about a fracture is key to judging its effect, but detailed information about complex fracture networks is difficult to obtain. In this paper, we propose a new method to describe the shape of a complex fracture network. This method is based on microseismic results and uses the L-system to establish a method for characterizing a complex fracture network. The method also combines with decomposition to construct a new method called the multiobjective fracture network inversion algorithm based on decomposition (MOFNIAD). The coverage of microseismic monitoring results and the degree of fitting of production data are the two objective functions of the inversion fracture network. The multiobjective fracture network inversion algorithm can be optimized to obtain multiple optimal solutions that meet different target weights. Therefore, this paper es... [more]

A control technique combining pulse width modulation (PWM) and pulse amplitude modulation (PAM) is presented herein to reduce the output voltage ripple of the converter as little as possible. Such a converter requires a two-stage cascaded structure. The first stage is the buck-boost converter, which is used to adjust the output voltage of the second power stage, whereas the second stage is the two-phase interleaved buck converter, which is used to reduce the output voltage ripple. In theory, the two phases of the second stage operate under the condition of individual duty cycles of 50% with a phase difference of 180° between the two, and hence, the currents in the two phases are cancelled for any period of time, thereby making the output voltage of the converter almost voltage-free. Moreover, in order to improve the overall efficiency further, the proposed soft-switching technique based on an active clamp is presented and applied to these two stages to render the main and auxiliary swi... [more]

The quantitative evaluation of cluster wind power output volatility and source-load timing matching is vital to the planning and operation of the future power system dominated by new energy. However, the existing volatility evaluation methods of cluster wind power output do not fully consider timing volatility, or are not suitable for small sample data scenarios. Meanwhile, the existing source-load timing matching evaluation indicator ignores the impact of wind power permeability on the timing matching degree between wind power output and load. Therefore, the authors propose quantitative evaluation methods of cluster wind power output volatility and source-load timing matching in regional power grid. Firstly, the volatility-based smoothing coefficient is defined to quantitatively evaluate the smoothing effect of wind-farm cluster power output. Then, the source-load timing matching coefficient considering wind power permeability is proposed to quantitatively evaluate the timing matching... [more]

The management of the power transformer population is a complex process, as the grid companies operate thousands of devices. For this issue, the health index method can be applied to facilitate asset management. The algorithm can be used not only in the technical assessment of the individual units, but also to determine the relationships within the whole population. In this paper, the presented health index method consists of periodic oil diagnostics, including the physicochemical properties, dissolved gas analysis, and furfural content, and further assessment in terms of the criticality of the device to determine the technical condition. The algorithm was specifically designed to reflect even the smallest changes of the input parameters in the final score. The performance of the health index was tested on 620 oil analyses from 220 transformers divided into four subpopulations based on the service conditions. The results have proven to be largely dependent on the criticality level and... [more]

Railway transit forms the backbone of sustainable transportation systems, which are necessary to limit the effects of global warming. In this paper, the authors seek to determine whether there is a statistically significant difference in energy consumption between distinct railway vehicle types. Firstly, the energy consumption measurement methods in the railway transportation sector are described and compared to each other in respect to precision and cost. Secondly, the use of energy consumption as a criterion in rolling stock tenders with the associated norm is analysed, particularly with regard to the life-cycle cost of railway vehicles. In the next part real life data on energy consumption of six distinct passenger electrical railway vehicle types is presented and analysed in order to compare the efficiency of different types of rolling stock. The differences in energy efficiency between rolling stock types may be used to improve the procurement process ensuring train operating comp... [more]

The flexible excitation system (FES) is a kind of novel excitation system with two channels for damping control. Besides the basic functions of traditional excitation systems, flexible excitation systems can provide reactive power support for the terminal voltage, and the large-capacity FES can improve the voltage stability and power-angle stability of synchronous generator units. However, with the increase in system capacity and the complication of control objectives, the difficulty of controller design will be increased. The randomness and fluctuation of new energy resources such as photovoltaic and wind turbines may cause disturbance and fault to the power system, which requires the coordinated control strategy for the FES to achieve stability in voltage and power angle. In this paper, the basic characteristics of FES are analyzed, and the mathematic model of the single machine infinite bus (SMIB) system based on FES is derived. The coordinated control strategy based on decoupling c... [more]

The use of biofuels for spark ignition engines is proposed to diversify fuel sources and reduce fossil fuel consumption, optimize engine performance, and reduce pollutant emissions. Additionally, when these biofuels are produced from low-grade wastes, they constitute valorisation pathways for these otherwise unprofitable wastes. In this study, ethanol and pyrolysis biogasoline made from low-grade wastes were evaluated as additives for commercial gasoline (RON95, RON98) in tests performed in a spark ignition engine. Binary fuel mixtures of ethanol + gasoline or biogasoline + gasoline with biofuel incorporation of 2% (w/w) to 10% (w/w) were evaluated and compared with ternary fuel mixtures of ethanol + biogasoline + gasoline with biofuel incorporation rates from 1% (w/w) to 5% (w/w). The fuel mix performance was assessed by determination of torque and power, fuel consumption and efficiency, and emissions (HC, CO, and NOx). An electronic control unit (ECU) was used to regulate the air−fue... [more]

The introduction of the Green Deal in 2019 by the European Commission poses a significant challenge for EU member states whose power generation is based primarily on fossil fuels. In Poland, nearly 80% of the electricity is produced from fossil fuels. This paper presents an analysis of the risks related to the delays in the accomplishment of investment programs in the Polish power industry. Three scenarios were prepared for balancing the deficiency of about 3 GW of power and 20 TWh of electricity in the national power grid in the years 2031−2040, which may emerge as a result of the delayed accomplishment of investment programs, particularly in nuclear energy. The first scenario presents a variant entailing the rapid phasing out of coal and the replacement of the decommissioned power units with new gas-powered units, where the missing power volume would be partially balanced by import, and partially through gas-based production in the new power units. The second scenario assumes that th... [more]

Urban heat island (UHI) effects significantly impact building energy. Traditional UHI investigation methods are often incapable of providing the high spatial density of observations required to distinguish small-scale temperature differences in the UHI. Crowdsourcing offers a solution. Building cooling/heating load in 2018 has been estimated in London, UK, using crowdsourced data from over 1300 Netatmo personal weather stations. The local climate zone (LCZ) scheme was used to classify the different urban environments of London (UK). Inter-LCZ temperature differences are found to be generally consistent with LCZ temperature definitions. Analysis of cooling degree hours in July shows LCZ 2 (the densest urban LCZ in London) had the highest cooling demand, with a total of 1550 cooling degree hours. The suburban related LCZs 5 and 6 and rural LCZs B and D all had about 80% of the demand of LCZ 2. In December, the rural LCZs A, B and D had the greatest heating demand, with all recording arou... [more]

When operating in cold climates, wind turbines are vulnerable to ice accretion. The main impact of icing on wind turbines is the power losses due to geometric deformation of the iced airfoils of the blades. Significant energy losses during the wind farm lifetime must be estimated and mitigated. Finding solutions for icing calls on several areas of knowledge. Modelling and simulation as an alternative to experimental tests are primary techniques used to account for ice accretion because of their low cost and effectiveness. Several studies have been conducted to replicate ice growth on wind turbine blades using Computational Fluid Dynamics (CFD) during the last decade. While inflight icing research is well developed and well documented, wind turbine icing is still in development and has its peculiarities. This paper surveys and discusses the models, approaches and methods used in ice accretion modelling in view of their application in wind energy while summarizing the recent research fin... [more]