The microbial oxidation of CH4 in biochar-modified soil cover is considered a potent option for the mitigation of emissions from old landfills or sites containing wastes full of low CH4 generation rates. The mechanism of methane oxidizing bacteria (MOB) can be enhanced by amending the landfill cover soil with biochar, which is recalcitrant to biological degradation and can adsorb CH4 while facilitating the growth and activity of MOB within its porous structure. However, the increase in the permeability coefficient and water content of the cover due to the addition of biochar also affects the methane removal efficiency. A hydrophobic biochar modified by KH-570 was employed to reduce the water content and to promote the diffusion and oxidation of CH4 in the cover. Several series of small-scale column tests were conducted to quantify the CH4 oxidation properties of the landfill cover soil amended with biochar and hydrophobic biochar under different levels of exposed CH4 concentrations (5%... [more]

In this study, a well-to-wheels life cycle assessment was conducted to determine the environmental impacts from disposing of petroleum coke by converting it into liquid fuel. Specifically, three processes for converting petroleum coke and natural gas to Fischer Tropsch diesel were investigated, both with and without carbon capture and sequestration (CCS). Impact categories were calculated using the EPA’s TRACI 2.1 US-Canada 2008 midpoint method in SimaPro software. In addition, the impact of grid emissions on the overall process was assessed using two representative Canadian locations with high (Alberta) and low (Ontario) grid emissions. The results of each impact category were compared among the designs and against conventional petroleum and oil-sands derived diesel. Key findings showed that the proposed designs when operated using CCS in the low-emissions-grid location had lower life cycle GHG emissions than conventional petroleum and oil-sands derived diesel. Nevertheless, the vario... [more]

The editorial team greatly appreciates the reviewers who have dedicated their considerable timeand expertise to the journal’s rigorous editorial process over the past 12 months, regardless ofwhether the papers are finally published or not [...]

This is a submission of source file of the life cycle analysis of steel manufacturing off-gas utilization systems using SimaPro V9. It includes five locations: Ontario, the USA, Finland, Mexico, and China.

Bedded pack manure has long been considered an unsuitable feedstock for conventional anaerobic digestion systems due to its high solids content. However, solid-state anaerobic digestion (SS-AD) provides an opportunity to generate methane from such high-solids feedstocks. This study was conducted to determine the influence of moisture content on the digestion of bedded pack dairy manure using SS-AD. Mixtures of sawdust bedding and dairy manure were prepared with moisture contents (MCs) of 70, 76, and 83% and digested at 37 °C for 85 days. The performance of digesters containing manure at 83% MC was 1.3 to 1.4-fold higher than that of digesters containing 70% MC manure in terms of volatile solids (VS) reduction and biogas production. VS reduction rates were 55 to 75% and cumulative methane yield ranged from 64 to 90 NmL (gVS)−1. These values are lower than those from SS-AD of fresh manure and this is likely due to the partial decomposition of biodegradable materials during the two to thr... [more]

The paper presents the possibility of applying a twin-screw press for juice extraction from apples with different textural properties. The research was carried out with six different varieties; namely, Granny Smith, Modi, Ligol, Lobo, Boscop and Szampion. During the experiment, the following properties were measured: texture properties, pressing yield and polyphenolic content; and ascorbic acid content and antioxidant activity both in raw apples and apple juice. Based on the analysis, three hardness levels of apples can be distinguished, impacting the course of juice pressing in a twin-screw press (low hardness below 30 N, medium hardness 30−50 N and high hardness 50 N). The study showed that only high hardness apples are suitable for pressing on a twin-screw press. The mechanism by which texture properties influence the juice pressing process in the studied press was explained. It was further demonstrated that the hardness of apples has a positive impact on the degree of extraction of... [more]

It has been proven that polymer injection at early times is beneficial to offshore heavy oil recovery. It is of significant importance to optimize the polymer injection timing and decide the residual oil distribution after polymer flooding. Aiming at a specific offshore heavy oil reservoir in Bohai, China, the optimum polymer injection timing is investigated through laboratory experiments. The influence of polymer injection timing on oil displacement and remaining oil distribution is analyzed by combining macroscopic and microscopic flooding experiments. The results reveal that the optimum polymer injection timing should be close to the water breakthrough, i.e., just before the waterflooding front reaches the outlet of the core. In addition, the waterflooding front position is analytically solved by using the Buckley−Leverett method and verified by experimental results, which supply an approach to predict the polymer injection timing. When polymer is injected before the waterflood fron... [more]

The toxic pollutants phenol and cyanide in the bio-treated effluent of coking wastewater still need advanced treatment to meet environmental requirements. In this study, activated carbon prepared from municipal sludge and bamboo waste (SBAC) was used for simultaneous adsorption of phenol and cyanide from bio-treated effluent of coking wastewater. The results showed that the optimum removal efficiencies of volatile phenol (69.7%) and total cyanide (80.1%) were observed at a SBAC dosage of 8 g/L, a pH value of 8.0, and a contact time of 80 min. The physical and chemical properties of SBAC were analyzed using Brunauer−Emmett−Teller (BET) surface area (SBET), scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) spectroscopy. SBAC had high SBET (289.58 m2/g) and rich mesoporous structure (average pore diameter of 3.688 nm), and carboxylic groups on SBAC surfaces were enhanced due to the addition of bamboo waste. In addition, a kinetic model of pseudo-first-order fitted... [more]

In this study, a new type of hydrophobic cationic polyacrylamide P (AM-DMC-DABC) (PADD) was synthesized by ultrasonic (US)-initiated polymerization, which is used for the separation and removal of coal mine wastewater. The acrylamide (AM), methacryloyloxyethyl trimethyl ammonium chloride (DMC) and acryloyloxyethyl dimethylbenzyl ammonium chloride (DABC) were used as monomers to prepare). The factors that affecting the US initiated polymerization of PADD were analyzed. Fourier transform infrared spectroscopy (FT-IR), 1H nuclear magnetic resonance (1H NMR) and scanning electron microscopy (SEM) were used to characterize the chemical structure, thermal decomposition performance and surface morphology of the polymers. FT-IR and 1H NMR results showed that PADD was successfully synthesized. In addition, irregular porous surface morphology of PADD were observed by SEM analysis. Under the optimum conditions (pH = 7.0, flocculant dosage = 16.0 mg/L), the excellent flocculation performance (turb... [more]

The affinity law is widely used in pump design and experiments. The applicability of the affinity law in an emergency drainage pump at different rotating speeds was studied. Experiments and numerical simulation through ANSYS CFX (Computational Fluid Dynamics X) 15.0 software were used to research the affinity law characteristics. Results show that the simulation of characteristics is basically consistent with the experimental curves. In small flow rate conditions, due to the existence of obvious differential pressure between the pressure side and the suction side in the impeller blade tip area, the leakage flow occurs at the tip clearance, which collides with the main stream at the inlet and generates vortices at the leading edge of the impeller. The tip leakage flows of the pump at four different rotating speeds were compared, and it was found that the tip leakage increased with increasing rotation speed, and at the same rotation speed, the tip leakage flow was large in the small flow... [more]

High-speed countercurrent chromatography (HSCCC) and silica gel column chromatography were used to separate and purify alkaloids from Chinese herbal medicine Euchresta tubulosa Dunn. The purpose of this study is to provide a system mode for rapid separation of alkaloids from natural products. In the experiment, the eluent of silica gel column chromatography was screened by thin layer chromatography (TLC) to obtain four components with different polarity. Then, the two-phase solvent systems of different components were selected and purified by HSCCC. Four alkaloids with relatively high content were obtained by this mode successfully, including matrine (28 mg), oxymatrine (32 mg), N-formyl cytisine (24 mg), and cytisine (58 mg). The purity was higher than 91% by high performance liquid chromatography−ultraviolet (HPLC-UV) and their chemical structures were identified by nuclear magnetic resonance (NMR) and electron ionization mass spectrometry (EI-MS). The results showed that the combina... [more]

Spiral nozzles are widely used in wet scrubbers to form an appropriate spray pattern to capture the polluting gas/particulate matterwith the highest possible efficiency. Despite this fact, and a fact that it is a nozzle with a very atypical spray pattern (a full cone consisting of three concentric hollow cones), very limited amount of studies have been done so far on characterization of this type of nozzle. This work reports preliminary results on the spray characteristics of a spiral nozzle used for gas absorption processes. First, we experimentally measured the pressure impact footprint of the spray generated. Then effective spray angles were evaluated from the photographs of the spray and using the pressure impact footprint records via Archimedean spiral equation. Using the classical photography, areas of primary and secondary atomization were determined together with the droplet size distribution, which were further approximated using selected distribution functions. Radial and tan... [more]

In this study we explored the implementation of the vapor induced phase separation (VIPS) to produce cellulose acetate microcapsules for the encapsulation of a complex mix of fragrances. VIPS is a technique used for membrane preparation, but barely mentioned for microencapsulation. We compared the products from VIPS and a more common microencapsulation process, the immersion precipitation technique (IPS). The capsules prepared via VIPS show a core-shell structure with a thin polymeric shell surrounding the internally empty space, conversely to those produced via IPS, showing an incomplete spherical morphology. This can be attributed to a better control of the precipitation rate of the encapsulation material in the non-solvent thanks to the longer exposition time to the vapor. The activity and encapsulation efficiency of the capsules, obtained through TGA analysis, reached a maximum of ≈75% and ≈90%, respectively. Moreover, a growing trend between the initial active concentration and th... [more]

We characterize the long-term development of high-viscosity gas−liquid intermittent flows by means of a detrended fluctuation analysis (DFA). To this end, the pressures measured at different locations along an ad hoc experimental flow line are compared. We then analyze the relevant time-series to determine the evolution of the various kinds of intermittent flow patterns associated with the mixtures under consideration. Although no pattern transitions are observed in the presence of high-viscosity mixtures, we show that the dynamical attributes of each kind of intermittence evolves from one point to another within the transport system. The analysis indicates that the loss of a long-range correlation between the pressure responses are due to the discharge processes.

The amount of fines in sand greatly influence the permeability of sandy soils. Thus, this research was conducted to study the effect of plastic and non-plastic fines on the permeability of three types of sands (Lawrencepur sand, Chenab sand and Ravi sand). For this purpose, plastic and non-plastic fines were collected from different location of Lahore. Samples were prepared by mixing plastic and non-plastic fines into each type of sand separately, in amounts ranging from 0% to 50% with increments of five percent. Overall 63 samples were prepared. Sieve analysis and hydrometric analysis were performed to obtain particle size distribution for each sample. Atterberg’s limits were also determined and each sample was classified according to the Unified Soil Classification System (USCS). Compaction tests were performed on all samples as per the procedure in a standard Proctor test. The test samples were compacted in permeability molds with optimum moisture contents to obtain the density, as... [more]

The water inrush from karst collapse column (KCC) is a cascading, vicious cycle disaster caused by geological and mining activities, that can cause serious casualties and property losses. The key to preventing this risk is to study the mechanism of water inrush under confining pressure. Aiming at the investigationg the characteristics of the KCC named X1 in Chensilou mine, a series of methods, including connectivity experiments, water pressure monitoring tests in two side-walls, and numerical simulations based on plastic damage-seepage (PD-S) theory have been developed. The methods are used to test the security of the 2519 mining area, the damage thickness, pore water pressure, and seepage vector in the X1. The results indicate that the X1 has a certain water blocking capacity. In addition, with the decrease of confining pressure and increase of shear stress, deviatoric stress could cause the increase of permeability, the reduction of strength, and the reduction of pore water pressure... [more]

The seepage velocity and temperature externally manifest the changing structure, gas desorption and energy release that occurs in coal containing gas failure under loading. By using the system of coal containing gas failure under loading, this paper studies the law of seepage velocity and temperature under different loading rates and at 1.0 MPa confining pressure and 0.5 MPa gas pressure, and combined the on-site results of gas pressure and temperature. The results show that the stress directly affects the seepage velocity and temperature of coal containing gas, and the pressure and content of gas have the most sensitivity to mining stress. Although the temperature is not sensitive to mining stress, it has great correlation with mining stress. Seepage velocity has the characteristic of critically slowing down under loading. This is demonstrated by the variance increasing before the main failure of the samples. Therefore, the variance of seepage velocity with time and temperature can pr... [more]

Cylindrical 18650-type lithium-ion cells are being utilized more often for automotive applications. This introduces error in calculating expected lifetime due to varied usage conditions accelerating or reducing material damage. One such usage condition is vibration, which has been shown to impact the electrical performance over extended periods. Within this study X-ray photoelectron spectroscopy (XPS) has been performed on nickel manganese cobalt (NMC) cells subjected to vibration. This study found that vibration causes the removal of the selectively-formed surface film created during a cell’s first cycles and replaces it with the surface film from electrolyte decomposition. The surface films formed by vibration are composed of much higher concentrations of organic electrolyte decomposition products than the film from the control cell. The impact of this chemical mechanism is an increased level of cell degradation. This is exhibited in increased capacity fade and cell impedance. This i... [more]

This study proposes an effective method to inspect inaccessible nuclear power reactor head nozzles using interface waves that propagate along the shrink fit boundary of a reactor head. The reactor head is relatively thick, which makes it difficult to inspect from the outside by conventional ultrasonic testing. However, interface waves can propagate a long distance from a fixed transducer position. The inside of the nuclear reactor has limited access due to the high radiation, so the transducers are located outside the nuclear reactor head, and interface waves propagate into the nuclear reactor to detect defects. A numerical simulation and experiments were carried out to validate the method. Various defect cases that simulate field failures are also presented, and the proposed technique shows satisfactory defect classification.

Pulse width modulation strategies have been developed for indirect matrix converters (IMCs) in order to improve their performance. In indirect matrix converters, the LC input filter is used to remove input current harmonics and electromagnetic interference problems. Unfortunately, due to the existence of the input filter, the input power factor is diminished, especially during operation at low voltage outputs. In this paper, a new space vector modulation (SVM) is proposed to compensate for the input power factor of the indirect matrix converter. Both computer simulation and experimental studies through hardware implementation were performed to verify the effectiveness of the proposed modulation strategy.

The technology of gerotor pumps is progressing towards cutting-edge applications in emerging sectors, which are more demanding for pump performance. Moreover, recent environmental standards are heading towards leakage-free and noiseless hydraulic systems. Hence, in order to respond to these demands, this study, which will be referred to as the GeroMAG concept, aims to make a leap from the standard gerotor pump technology: a sealed, compact, non-shaft-driven gerotor pump with a magnetically-driving outer rotor. The GeroMAG pump is conceived as a variable-flow pump to accomplish a standard volumetric flow rate at low rotational speed with satisfactory volumetric efficiency. By following the authors’ methodology based on a catalogue of best-practice rules, a custom trochoidal gear set is designed. Then, two main technological challenges are encountered: how to generate the rotational movement of the driving outer rotor and how to produce the guide of rotation of the gear set once there is... [more]

This paper proposes a novel high-efficiency isolated three-port bidirectional DC/DC device for photovoltaic (PV) systems. The device contains a high step-up converter for PV modules to supply power to the DC bus, and a bidirectional charge/discharge control circuit for the battery with an improved boost-flyback converter. When the PV modules supply sufficient energy, their output can be stepped up and energy supply to the DC bus and charging of the battery can be achieved simultaneously. However, when the energy supplied is insufficient, the battery provides energy to the DC bus. When the proposed converter is operated in the step-down mode, the DC-blocking capacitor on the high-voltage side is used to reduce the voltage on the transformer and achieve high step-down performance. Moreover, to improve the overall efficiency of the system, the energy stored in the leakage inductance is recycled and supplied to the DC-blocking capacitor during operation in the step-up mode. Finally, to ver... [more]

Reduction of nitric oxides (NOx) in aircraft engines and in gas turbines by lean combustion is of great interest in the design of novel combustion systems. However, the stabilization of the flame under lean conditions is a main issue. In this context, the present work investigates the effects of sinusoidal dielectric barrier discharge (DBD) on a lean inverse diffusive methane/air flame in a Bunsen-type burner under different actuation conditions. The flame appearance was investigated with fixed methane loading (mass flux), but with varying inner airflow rate. High-speed flame imaging was done by using an intensified (charge-coupled device) CCD camera equipped with different optical filters in order to selectively record signals from the chemiluminescent species OH*, CH*, or CO2* to evaluate the flame behavior in presence of plasma actuation. The electrical power consumption was less than 33 W. It was evident that the plasma flame enhancement was significantly influenced by the plasma d... [more]

C-core linear flux-switching permanent magnet (PM) machines (LFSPMs) are attracting more and more attention due to their advantages of simplicity and robustness of the secondary side, high power density and high torque density, in which both PMs and armature windings are housed in the primary side. The primary salient tooth wound with a concentrated winding consists of C-shaped iron core segments between which PMs are sandwiched and the magnetization directions of these PMs are adjacent and alternant in the horizontal direction. On the other hand, the secondary side is composed of a simple iron core with salient teeth so that it is very suitable for long stroke applications. However, the detent force of the C-core LFSPM machine is relatively high and the magnetic circuit is unbalanced due to the end effect. Thus, a new multiple additional tooth which consists of an active and a traditional passive additional tooth, is employed at each end side of the primary in this paper, so that the... [more]

A hollow cylinder flywheel rotor with a novel outer rotor switched reluctance machine (SRM) mounted on the interior rim is presented, with measurements, numerical analysis and analytical models. Practical experiences from the construction process are also discussed. The flywheel rotor does not have a shaft and spokes and is predicted to store 181 Wh / kg at ultimate tensile strength (UTS) according to simulations. The novel SRM is an axial flux machine, chosen due to its robustness and tolerance for high strain. The computed maximum tip speed of the motor at UTS is 1050 m / s . A small-scale proof-of-concept electric machine prototype has been constructed, and the machine inductance has been estimated from measurements of voltage and current and compared against results from analytical models and finite element analysis (FEA). The prototype measurements were used to simulate operation during maximal speed for a comparison towards other high-speed electric machines, in te... [more]