It is well known that PV thin films can be deposited by an extensive range of more or less expensive and complicated techniques (such as sputtering, chemical vapor deposition (CVD), physical vapor deposition (PVD), pulsed laser deposition, atomic layer deposition (ALD)). The present paper focuses on TCO layers applied by chosen techniques, including mainly the ALD and CVD methods. Thin layers of transparent conductive oxides constitute a well-known group of materials with unique properties. Oxides such as ZnO, SnO2, and In2O3 are the most significant materials of this type; some of them are discussed in the paper. From the application point of view in the photovoltaic industry, the goal is to apply a method that will provide the highest value of electric charge conductivity while maintaining the minimum value of absorption in the layer and a reduced value of the reflection coefficient. The implementation of significant achievements in the coming decade is for developing guidelines for... [more]

In order to adjust to the change of the large-scale deployment of photovoltaic (PV) power generation and fully exploit the potentialities of an integrated energy distribution system (IEDS) in solar energy accommodation, an evaluation method on maximum hosting capacity of solar energy in IEDS based on convex relaxation optimization algorithm is proposed in this paper. Firstly, an evaluation model of maximum hosting capacity of solar energy for IEDS considering the electrical-thermal comprehensive utilization of solar energy is proposed, in which the maximization of PV capacity and solar collector (SC) capacity are fully considered. Secondly, IEDS’s potential in electricity, heat, and gas energy coordinated optimization is fully exploited to enhance the hosting capacity of solar energy in which the electric distribution network, heating network, and natural gas network constraints are fully modeled. Then, an enhanced second-order cone programming (SOCP)-based method is employed to solve... [more]

As the world is transitioning to electric vehicles (EVs), the existing power grids are facing several challenges. In particular, the additional charging power demand may repeatedly overload the traditionally-sized distribution transformers and adversely impact their operational life. To address this challenge, this paper proposes an EV-based reactive power compensation strategy for transformer overloading mitigation. Specifically, a low-bandwidth centralized recursive controller is proposed to determine a set point for the EV’s onboard charger’s reactive power. Importantly, the proposed strategy is practically implementable in existing distribution grids as it does not rely on smart grid infrastructure and is stable under potential communication delays and partial failures. This paper discusses the controller’s structure, design, and stability in detail. The proposed solution is tested with a realistic secondary distribution system considering four different EV charging scenarios with... [more]

Aiming to investigate the rotation effect on the natural convection and heat transfer of nanofluid, which has an important application in the control of heat transfer, the velocity field and temperature distribution inside the square cylinder with the rotating heat source in the center were numerically studied and presented in detail at different Hartman numbers and aspect ratios using the immersed boundary-lattice Boltzmann method. Then, the average Nusselt number on the surface of the heat source was calculated to compare the heat transfer rate in different cases. The results showed that the rotation would reduce the effect of gravity on the flow and suppress the heat transfer between the rotating heat source and nanofluid, while the external magnetic field would reduce the rotation effect on the flow and suppress or promote the heat transfer depending on the rotational speed and aspect ratio. Moreover, the smaller aspect ratio of the heat source to the square cylinder would enhance... [more]

The worldwide aspiration for a sustainable energy future has led to an increasing deployment of variable and intermittent renewable energy sources (RESs). As a result, predicting and planning the operation of power grids has become more complex. Batteries can play a critical role to this problem as they can absorb the uncertainties introduced by RESs. In this paper, we solve the problem of computing a dispatch plan for a distribution grid with RESs and batteries with a novel approach based on Reinforcement Learning (RL). Although RL is not inherently suited for planning problems that require open loop policies, we have developed an iterative algorithm that calls a trained RL agent at each iteration to compute the dispatch plan. Since the feedback given to the RL agent cannot be directly observed because the dispatch plan is computed ahead of operation, it is estimated. Compared to the conventional approach of scenario-based optimization, our RL-based approach can exploit significantly... [more]

Energy is the driver of the socioeconomic growth and development of a country. In the pursuit of available and affordable sources of energy, nations around the world have forgotten the sustainability angle and are facing an energy crisis. The developing world has initiated development plans in an unsustainable way, causing a demand−supply gap and leading to very high energy prices. Renewable energy gives us a solution to this circular crisis. The recent world has seen significant investment in renewables, particularly in the wind energy sector. The investment was initiated as a government spending program, but is now taken up by the private sector. The current study presents a thorough analysis of the prospects for wind energy and the means and measures required to fully capacitate the sector in Pakistan. In Pakistan’s three largest provinces, there is tremendous potential for wind energy, which requires proper utilization and exploration for sustained socioeconomic development. This s... [more]

Satellite-derived solar irradiance is advantageous in solar resource assessment due to its high spatiotemporal availability, but its discrepancies to ground-observed values remain an issue for reliability. Site adaptation can be employed to correct these errors by using short-term high-quality ground-observed values. Recent studies have highlighted the benefits of the sequential procedure of a regressive and a distribution-mapping technique in comparison to their individual counterparts. In this paper, we attempted to improve the sequential procedure by using various distribution mapping techniques in addition to the previously proposed quantile mapping. We applied these site-adaptation techniques on the global horizontal irradiance (GHI) and direct normal irradiance (DNI) obtained from the UASIBS-KIER model in Daejeon, South Korea. The best technique, determined by a ranking methodology, can reduce the mean bias from −5.04% and 13.51% to −0.45% and −2.02% for GHI and DNI, respectively... [more]

Understanding the processes occurring during the nanocrystallization of glass-forming liquids is important for creating artificial nanostructures for various applications. In this article, local thermal perturbations in supercooled glass-forming liquids and polymers during the nucleation of a crystalline phase are studied. To describe the thermal response of supercooled glass-forming liquids, an integro-differential heat equation with dynamic heat capacity is used. We have found that the effect of the dynamic heat capacity is significant for fast local thermal perturbations that arise in the early stages of crystal nucleation in glass-forming liquids and polymers. It has been established that local temperature perturbations during the nucleation of crystals in silicate glasses and polymers can change the nucleation rate by 2−5 orders of magnitude. The knowledge gained can be useful for the technology of artificial microstructures and advanced materials.

Energy accessibility, reliability and availability are key components of improved quality of life and human development in all spheres. As the United Nations’ SDG 7 calls for access to electricity for all by 2030, Africa still has a wide gap to fill as the statistics show that 85% of the population that will not have access to electricity is in Africa. As the world tries to wean itself off non-renewable energy and transition to green through use of renewable energy sources, hydropower energy remains at the heart of Africa for this venture. With majority of the rural population in Africa lacking electricity, there is need for a low-tech system that utilizes river flow to generate just enough energy for normal operation in these regions. Micro-hydrokinetic river turbine technology (µ-HRT), which offers less intermittency, can potentially contribute to sustainably electrifying Africa rural areas. The technology has been adopted by few countries worldwide, with limited comprehensive study... [more]

In this study, the authors explored the issues of the Soderbergh electrolysis cell’s increase in economic efficiency. This result was achieved by analyzing the temperature fields of the electrolysis cell in order to determine the overheating points. As a result, it led to the determination of the points of the hearth bottom’s subsequent breakdown, causing the failure of the electrolysis cell. In this paper, the mathematical modeling of the temperature fields using a spatially distributed mathematical model and conducted experimental studies were carried out. The mathematical model also provides the opportunity to measure the temperature field in the hearth bottom (at the bottom) of the OA-300M electrolysis cell. The results of the given research can be used to solve the experimental determination of the hearth bottom internal defect problem.

Complex multiphase flow problems in ocean engineering have long been challenging topics. Problems such as large deformations at interfaces, multi-media interfaces, and multiple physical processes are difficult to simulate. Mesh-based algorithms could have limitations in dealing with multiphase interface capture and large interface deformations. On the contrary, the Smoothed Particle Hydrodynamics (SPH) method, as a Lagrangian meshless particle method, has some merit and flexibility in capturing multiphase interfaces and dealing with large boundary deformations. In recent years, with the improvement of SPH theory and numerical models, the SPH method has made significant advances and breakthroughs in terms of theoretical completeness and computational stability, which starts to be widely used in ocean engineering problems, including multiphase flows under atmospheric pressure, high-pressure multiphase flows, phase-change multiphase flows, granular multiphase flows and so on. In this pape... [more]

Wind turbine icing has been the subject of intensive research over the past two decades, primarily focusing on applying computational fluid dynamics (CFD) to 2D airfoil simulations for parametric analysis. As a result of blades’ airfoils deformation caused by icing, wind turbines experience a considerable decrease in aerodynamic performance resulting in a substantial loss of productivity. Due to the phenomenon’s complexity and high computational costs, a fully 3D simulation of the entire iced-up rotating turbine becomes infeasible, especially when dealing with several scenarios under various operating and weather conditions. The Quasi-3D steady-state simulation is a practical alternative method to assess power loss resulting from ice accretion on wind turbine blades. To some extent, this approach has been employed in several published studies showing a capability to estimate performance degradation throughout the generation of power curves for both clean and iced wind turbines. In this... [more]

Triply periodic minimal surfaces (TPMS) have shown better mechanical performance, mass transfer, and thermal conductivity than conventional and strut-based structures, which have been employed in different disciplines. Most of the literature investigates different TPMS topologies in cooling channels to enhance thermal performance due to the smooth curvature and large surface area. However, a deeper investigation of the effects of TPMS design variables and the thermal performance advantages of cooling channels is required. This review details the effects of TPMS design variables, i.e., porosity, wall thickness, and unit cell size, on flow and heat transfer enhancement. It is found that varying the design variables significantly changes the flow and heat transfer characteristics. Also, by comparing TPMS and conventional cooling structures, it is found that most TPMS structures show better thermal performance than other strategies. Moreover, different fabrication methods for TPMS-based co... [more]

How dependent are European power systems and economies on natural gas? To answer this pressing question, we coupled a simulation model for assessing security of electricity supply and an economic optimization model. With this, we were able to analyze different reduction scenarios of the amount of gas utilized in the power sector. Our results show that reducing the amount of natural gas in the European power sector by up to 30% has a relatively moderate impact on the security of electricity supply. Restrictions of 40% or more result in substantially higher reductions in electricity demand shortfall and are associated with economic costs of more than EUR 77 billion. Furthermore, we demonstrate that a close coordination of gas distribution on a European level would be instrumental in mitigating negative economic consequences. Finally, it can be deduced that a coordinated delay of planned power plant shutdowns could effectively compensate for reduced gas volumes in the electricity sector.

Lithium cobalt oxide (LCO) cathode has been widely applied in 3C products (computer, communication, and consumer), and LCO films are currently the most promising cathode materials for thin-film lithium batteries (TFBs) due to their high volumetric energy density and favorable durability. Most LCO thin films are fabricated by physical vapor deposition (PVD) techniques, while the influence of preparation on the materials’ properties and electrochemical performance has not been highlighted. In this review, the dominant effects (heating, substrate, power, atmosphere, etc.) on LCO thin films are summarized, and the LCO thin films fabricated by other techniques (spin coating, sol−gel, atomic layer deposition, pulsed laser deposition, etc.) are outlined. Moreover, the modification strategies including bulk doping and surface coating for powder and thin-film LCO electrodes are discussed in detail. This review may pave the way for developing novel, durable, and high-performance LCO thin films b... [more]

Fuel with the addition of water, forming fuel-water emulsions, is a potential way to reduce the emission of pollutants from gas turbines powered by any liquid fuel. This article analyzes the available work on the combustion of fuel-water emulsions in gas turbines. The literature analysis was preceded by a theoretical introduction on fuel-water emulsion, taking into account the factors influencing its micro- and macroscopic properties. The basic features of the agents used to stabilize the emulsion were also discussed and the process of its combustion was described. The analyzed research differed in terms of the test stands on which the experiments were conducted, the fuel constituting the continuous phase of the emulsion, the amount of water contained in the mixture and the method of producing the emulsion. On the basis of the conducted analysis, conclusions were drawn concerning the influence of feeding a gas turbine with a fuel-water emulsion on the emission of nitrogen oxides, carbo... [more]

Oil, coal, and natural gas are traditional fossil energy sources and the main components of primary energy consumption globally [...]

Aqueous zinc-ion batteries (AZIBs) are being intensively developed as potential alternative electrochemical power sources, due to their advantages such as low cost, high safety, abundance of natural zinc resources and appropriate energy density. Among currently investigated prospective cathode materials for AZIBs, vanadium oxide-based composites with intrinsically conducting polymers have shown many advantages, such as high capacity, high power density and long battery life. This review gives a focused view of the design for the boosting of zinc ion storage performance using intrinsically conducting polymers in vanadium oxide-based composites and the mechanism of intercalation processes. The main challenges in interfacial engineering of vanadium oxide-conducting polymers composite structures and the prospects for further development of such cathode materials are summarized and discussed. The review would give rise to a broad interest focusing on the advantageous strategy of the develop... [more]

The prediction of gas productivity and reservoir stability of natural gas hydrate (NGH) reservoirs plays a vital role in the exploitation of NGH. In this study, we developed a THMC (thermal-hydrodynamic-mechanical-chemical) numerical model for the simulation of gas production behavior and the reservoir response. The model can describe the phase change, multiphase flow in porous media, heat transfer, and deformation behavior during the exploitation of NGH reservoirs. Two different production scenarios were employed for the simulation: depressurization and depressurization coupled with CO2 exchange. The simulation results suggested that the injection of CO2 promotes the dissociation of NGH between the injection well and the production well compared with depressurization only. The cumulative production of gas and water increased by 27.88% and 2.90%, respectively, based on 2000 days of production simulation. In addition, the subsidence of the NGH reservoir was lower in the CO2 exchange cas... [more]

When an axial-flow pump is running, there is a very complex flow inside the runner. Based on the two-way fluid−structure coupling method, this paper simulated the forward and reverse operating conditions of an axial-flow pump and calculated the dynamic stress distribution on the blade surface. The stress load spectrum was loaded onto the blade, and fatigue characteristic analysis was carried out to obtain the fatigue life and damage of the blade. This research shows the following: under different working conditions, the dynamic stress is concentrated at the root of the blade, and its amplitude decreases with the increase in the flow rate; at the same time, the change in stress with time shows a periodic change law. Under the working conditions of the turbine, the main frequency is the rotational frequency, and the secondary frequency is composed of multipliers of the rotational frequency, which is obviously affected by the number of blades; the fatigue damage and stress distribution ar... [more]

Electric vehicles (EVs) are emerging as an alternative transportation system owing to a reduction in depleting lubricates usage and greenhouse gas emissions. This paper presents a technical review of each and every sub-system and its feasible control of battery EV (BEV) propulsion units. The study includes the possible combination of electrical machines (EMs), storage system, and power electronic converters and their associated control strategies. The primary unit, i.e., EM, is the heart of the EV, which is used to drive the vehicle at the desired speed as well as to restore the regenerative braking (RB) energy that is generated to enhance the overall system reliability. To electrify the transportation sector, it is necessary to include new options of power electronic converter topologies and their associated control strategies for numerous reasons, which include extracting maximum power from sources in case the EV is powered from renewable energy resources, boosting the energy storage... [more]

Analyzing water availability from energy generation reservoirs is a determining factor in inferring the economic and development capacity of countries that operate primarily with hydroelectric generation. This is because the reservoirs configure the battery of this type of electric power generation system. In this context, the main interference variables are climate, consumptive use, operation, land use and occupation, topography, sediment input and geology. The present article analyzed rainfall data and the consumptive uses of five hydroelectric plants in the Rio Grande, operated by Furnas in Brazil. These two variables are chosen due to the frequent correlation between the rainfall regime and reservoir level and the scarcity of studies considering the influence of consumptive uses in this storage process. Data from 1994 to 2021 were analyzed from publicly available sources. The information was treated using the Mann−Kendall trend test. Having obtained the results, it was observed tha... [more]

A two-dimensional rectangular domain is considered with a discrete arrangement at equal distances from copper metal foam in a solar air heater (SAH). The local thermal non-equilibrium model is used for the analysis of heat transfer in a single-pass rectangular channel of SAH for different mass flow rates ranging from 0.03 to 0.05 kg/s at 850 W/m2 heat flux. Three different pores per inch (PPI) and porosities of copper metal foam with three different discrete thicknesses at equal distances are studied numerically. This paper evaluates the performance of SAH with 10 PPI 0.8769 porosity, 20 PPI 0.8567 porosity, and 30 PPI 0.92 porosity at 22 mm, 44 mm, and 88 mm thicknesses. The Nusselt number for 22 mm, 44 mm, and 88 mm thicknesses is 157.64%, 183.31%, and 218.60%, respectively, higher than the empty channel. The performance factor for 22 mm thick metal foam is 5.02% and 16.61% higher than for 44 mm and 88 mm thick metal foam, respectively. Hence, it is found that metal foam can be an ex... [more]

Hydrogen is a promising future fuel to enable the transition of transportation sector toward carbon neutrality. The direct utilization of H2 in internal combustion engines (ICEs) faces three major challenges: high NOx emissions, severe pressure rise rates, and pre-ignition at mid to high loads. In this study, the potential of H2 combustion in a truck-size engine operated in spark ignition (SI) and pre-chamber (PC) mode was investigated. To mitigate the high pressure rise rate with the SI configuration, the effects of three primary parameters on the engine combustion performance and NOx emissions were evaluated, including the compression ratio (CR), the air−fuel ratio, and the spark timing. In the simulations, the severity of the pressure rise was evaluated based on the maximum pressure rise rate (MPRR). Lower compression ratios were assessed as a means to mitigate the auto-ignition while enabling a wider range of engine operation. The study showed that by lowering CR from 16.5:1 to 12.... [more]

A voltage compensation and energy supplement-based power conversion system (VC-PCS) is proposed in this paper. A VC-PCS is a series connected to a battery that only processes fractional battery power; therefore, it has lower rated voltage and power in comparison with traditional PCSs. Compared with results of previous studies, the VC-PCS proposed herein can output bipolar voltage to meet voltage variation requirements and is a necessary and comprehensive improvement to previous research. First, its topology structure, working principle, and control strategy are comprehensively examined in this paper. Next, results of the simulations and physical experiments carried out are presented; the results show that the proposed VC-PCS is feasible in principle, and can be realized in physical applications.